P6SMB TSC | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

Features

/cuspopen For surface mounted application in order to optimize board space /cuspopen Low profile package /cuspopen Built-in strain relief /cuspopen Glass passivated junction /cuspopen Excellent clamping capability /cuspopen Fast response time: Typically less than 1.0ps from 0 volt to B V m i n . /cuspopen Typical IR less than 1μA above 10V /cuspopen High temperature soldering guaranteed: 250 O C / 10 seconds at terminals /cuspopen Plastic material used carries Underwriters Laboratory Flammability Classification 94V-0 /cuspopen 600 watts peak pulse power capability with a 10 x 1000 us waveform by 0.01% duty cycle Mechanical Data /cuspopen Case: Molded plastic /cuspopen Terminals: Solder plated /cuspopen Polarity: Indicated by cathode band /cuspopen Standard packaging: 12mm tape (EIA STD RS-481) /cuspopen Weight: 0.093gram SMB/DO-214AA Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Type Number Symbol Value Units Peak Power Dissipation at TA=25 O Tp=1ms(Note 1) PPK Minimum 600 Watts Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method) (Note 2, 3) - Unidirectional Only IFSM 100 Amps Maximum Instantaneous Forward Voltage at 50.0A for Unidirectional Only (Note 4) VF 3.5 Volts Operating and Storage Temperature Range TJ, TSTG -65 to + 150 OC Notes: 1. Non-repetitive Current Pulse Per Fig. 3 and Derated above TA=25OC Per Fig. 2. 2. Mounted on 5.0mm2 (.013 mm Thick) Copper Pads to Each Terminal. 3. 8.3ms Single Half Sine-wave or Equivalent Square Wave, Duty Cycle=4 pulses Per Minute Maximum. Devices for Bipolar Applications 1. For Bidrectional Use C or CA Suffix for Types P6SMB6.8 through Types P6SMB200A. 2. Electrical Characteristics Apply in Both Directions. .082(2.08) .076(1.93) .012(.31) .006(.15) .012(.31) .006(.15) .008(.20) .004(.10) .056(1.41) .035(0.90) .147(3.73) .137(3.48) .187(4.75) .167(4.25) .103(2.61) .078(1.99) .208(5.28) .200(5.08)

  • 621 - RATINGS AND CHARACTERISTIC CURVES (P6SMB SERIES) FIG.5- TYPICAL REVERSE LEAKAGE CHARACTERASTICS I , INSTANTANEOUS REVERSE LEAKAGED CURRENT , MICROAMPERES MEASURED AT DEVICES STAND-OFF VOLTAGE, V WM T = 25 CJ O V , BREAKDOWN VOLTAGE. VOLTS(BR) 0 100 200 300 400 500 1000 100 0.1 0.01 0.001 FIG.6- TYPICAL JUNCTION CAPACITANCE UNIDIRECTIONAL V , BREAKDOWN VOLTAGE. VOLTS(BR) C ,JUNCTION CAP ACITANCE. (pF) J MEASURED at ZERO BIAS Tj =25 C f = 1.0MHz Vsig = 50 mVp-p O MEASURED at STAND-OFF VOLTAGE, V WM 1 10 100 200 100 1000 6000 FIG.1- PEAK PULSE POWER RATING CURVE P , PEAK PULSE POWER, KW PPM tp, PULSE WIDTH, sec. 0.1 s 1.0 s 10 s 100 s 1.0ms 10ms 0.1 100 NON-REPETITIVE PULSE WAVEFORM SHOWN in FIG.3 T = 25 C J O FIG.3- PULSE WAVEFORM PEAK PULSE CURRENT t, TIME, ms 0 1.0 2.0 3.0 4.0 100 150 PULSE WIDTH (td) is DEFINED as the POINT WHERE the PEAK CURRENT DECAYS to 50% of I PPM Half Value - IPPM 10/1000 sec. WAVEFORM as DEFINED by R.E.A. FIG.2- PULSE DERATING CURVE PEAK PULSE POWER (P ) or CURRENT (IPPM) PP TA, AMBIENT TEMPERATURE. ( C) O DERATING IN PERCENT AGE. % 0 25 50 75 100 125 150 175 200 100 FIG.4- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT UNIDIRECTIONAL ONLY IFSM, PEAK FOR WARD SURGE CURRENT NUMBER OF CYCLES AT 60Hz AMPERES 8.3ms Single Half Sine Wave JEDEC Method 1 2 4 6 8 10 20 40 60 80 10010 100 200 tr = 10 sec Peak Value IPPM td
  • 622 - ELECTRICAL CHARACTERISTICS (TA=25OC unless otherwise noted) Test Stand-Off Maximum Maximum Maximum Maximum Device Device Current Voltage Reverse Leakage Peak Pulse Clamping Temperature Marking @IT VWM at VWM Current IRSM Voltage at IPPM Coefficient Code Min Max (mA) (Volts) I D (uA) (Note 2)(Amps) VC(Volts) of V BR(% / OC) Breakdown Voltage VBR (Volts) (Note 1)
  • 623 - ELECTRICAL CHARACTERISTICS (TA=25OC unless otherwise noted) Breakdown Voltage Test Stand-Off Maximum Maximum Maximum Maximum Device Device VBR Current Voltage Reverse Leakage Peak Pulse Clamping Temperature Marking (Volts) (Note 1) @IT VWM at VWM Current IRSM Voltage at IPPM Coefficient Code Min Max (mA) (Volts) I D (uA) (Note 2)(Amps) V C(Volts) of V BR(% / OC) P6SMB220A Notes: 1. VBR measured after IT applied for 300us, IT=square wave pulse or equivalent. 2. Surge current waverform per Figure 3 and derate per Figure 2. 3. For bipolar types having VWM of 10 volts and under, the ID limit is doubled. 4. For bidirectional use C or Ca suffix for types P6SMB6.8 through P6SMB200A. 5. All terms and symbols are consistent with ANSI/IEEE C62.35.