P40-G240

P40-G240-WH BOURNS | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 7

Technical content

Features

■ Formerly brand ■ Extremely high speed performance ■ Low impedance ■ Two TBU® protectors in one small package ■ Very high bandwidth, GHz compatible ■ Simple, superior circuit protection ■ RoHS compliant*, UL Recognized

Applications

■ xDSL (ADSL, VDSL, VDSL2) ■ High Data Rate Interface IC protection (LVDS, HDMI, etc.) ■ Industrial sensors and controls ■ General electronics P40-G Series TBU ® High-Speed Protectors *RoHS Directive 2002/95/EC Jan. 27, 2003 including annex and RoHS Recast 2011/65/EU June 8, 2011. Specifi cations are subject to change without notice. Customers should verify actual device performance in their specifi c applications. Transient Blocking Units - TBU® Devices Bourns® Model P40-G products are high-speed bidirectional protection components, constructed using MOSFET semicon- ductor technology, designed to protect against faults caused by short circuits, AC power cross, induction and lightning surges. The TBU ® high-speed protector, triggering as a function of the MOSFET, blocks surges and provides an effective barrier behind which sensitive electronics are not exposed to large voltages or currents during surge events. The TBU ® device is provided in a surface mount DFN package and meets industry standard requirements such as RoHS and Pb Free solder refl ow profi les. Electrical Characteristics (Tamb = 25 °C) The P40-G Series TBU® high-speed protector is bidirectional; specifi cations are valid in both directions. Symbol Parameter Min. Typ. Max. Unit Iop Maximum current through the device that will not cause current blocking 240 mA Itrigger Typical current for the device to go from normal operating state to protected state 350 mA Iout Maximum current through the device 480 mA Rdevice Series resistance of the TBU® device 3.6 4.2 Ω Rbal Line-to line series resistance difference between two TBU® devices 5 % tblock Maximum time for the device to go from normal operating state to protected state 0.2 µs Iquiescent Current through the triggered TBU® device with 40 Vdc circuit voltage 0.7 mA Vreset Voltage below which the triggered TBU® device will transition to normal operating state 7 V Absolute Maximum Ratings (Tamb = 25 °C) Symbol Parameter Value Unit Vimp Maximum protection voltage for impulse faults with rise time ≥ 1 µsec 40 V Vrms Maximum protection voltage for continuous Vrms faults 28 V Top Operating temperature range -40 to +85 °C Tstg Storage temperature range -65 to +150 °C Agency Approval UL recognized component File # E315805. Industry Standards Description Model Telcordia GR-1089 P40-G *RoHS COMPLIANT

Specifi cations are subject to change without notice. Customers should verify actual device performance in their specifi c applications. Typical Performance Characteristics P40-G Series TBU® High-Speed Protectors V-I Characteristics Time to Block vs. Fault Current Trigger Current vs. Temperature -Itrigger Vreset -Vreset Itrigger Time to Block vs. Fault Current 0.0000001 0.000001 0.00001 0.0001 0.001 0.01 0.1 0.1 1 10 100 1000 Fault Current (A ) Time to Block (sec) 100 120 140 -40 -20 0 20 40 60 80 Temperature (°C) % of Trigger Current

P40-G Series TBU® High-Speed Protectors Specifi cations are subject to change without notice. Customers should verify actual device performance in their specifi c applications. Operational Characteristics P40-G Lightning Protection 40 V The graph below demonstrates the operational characteristics of the TBU® device. In the graph below the fault voltage, protected side voltage, and current is presented. P40-G Load V1Line1 Line2 TEST CONFIGURATION DIAGRAM 1 µs/div. 10 V/div. 400 mA/div. Ch1 V1 Ch3 Current

A B D C 4 65 3 12 FF J N N H M KK E TOP VIEW SIDE VIEW BOTTOM VIEW J G G H Specifi cations are subject to change without notice. Customers should verify actual device performance in their specifi c applications. P40-G Series TBU® High-Speed Protectors Product Dimensions DIMENSIONS: MM (INCHES) Dim. Min. Typ. Max. A 3.90 (.154) 4.00 (.157) 4.10 (.161) B 3.90 (.154) 4.00 (.157) 4.10 (.161) C 0.80 (.031) 0.85 (.033) 0.90 (.035) D 0.000 (.000) 0.025 (.001) 0.050 (.002) E 2.55 (.100) 2.60 (.102) 2.65 (.104) F 0.20 (.008) 0.25 (.010) 0.30 (.012) G 0.75 (.030) 0.80 (.031) 0.85 (.033) H 1.40 (.055) 1.45 (.057) 1.50 (.059) J 0.10 (.004) 0.15 (.006) 0.20 (.008) K 0.25 (.010) 0.30 (.012) 0.35 (.014) M 0.55 (.022) 0.60 (.024) 0.65 (.026) N 0.20 (.008) 0.25 (.010) 0.30 (.012) Recommended Pad Layout Pad # Apply

1 In1

3 Out1

4 Out2

6 In2

NC = Solder to PCB; do not make electrical connection, do not connect to ground. Pad Designation TBU ® devices have matte-tin termination fi nish. Suggested layout should use non-solder stencil opening size 0.025 mm (.0010 in.) less than the device pad size. As when heat sinking any power device, it is recommended that, wherever possible, extra PCB copper area is allowed. For minimum parasitic capacitance, do not allow any signal, ground or power signals beneath any of the pads of the device. Thermal Resistances Symbol Parameter Value Unit Rth(j-a) Junction to Package Pads (1 TBU of Pair) 250 °C/W Rth(j-a) Junction to Package Pads (2 TBUs of Equal Power) 180 °C/W Block Diagram TBU® Device 0.90 (.035) 0.30 +0.05/-0.00 (.012 +.002/-.000) 0.35 (.014) 1.45 (.057) 0.30 (.012) 2.60 (.102) Thermal resistance using minimal pad size, where the power is the total power dissipated in the package. Additional copper pad area to be used for additional heatsinking is also recommended.

Specifi cations are subject to change without notice. Customers should verify actual device performance in their specifi c applications. P40-G Series TBU® High-Speed Protectors Refl ow Profi le Profi le Feature Pb-Free Assembly Average Ramp-Up Rate (Tsmax to Tp) 3 °C/sec. max. Preheat - Temperature Min. (Tsmin) - Temperature Max. (Tsmax) - Time (tsmin to tsmax) 150 °C 200 °C 60-180 sec. Time maintained above: - Temperature (TL) - Time (tL) 217 °C 60-150 sec. Peak/Classifi cation Temperature (Tp) 260 °C Time within 5 °C of Actual Peak Temp. (tp) 20-40 sec. Ramp-Down Rate 6 °C/sec. max. Time 25 °C to Peak Temperature 8 min. max. Typical Part MarkingHow to Order P 40 - G 240 - WH Form Factor P = Two TBU ® protectors in one device Impulse Voltage Rating 40 = 40 V Directional Indication G = Bidirectional Iop Indicator 240 = 240 mA MARKING NUMBER 04GC = P40-G240-WH MANUFACTURER’S TRADEMARK* PIN 1 MANUFACTURING DATE CODE* - 1ST DIGIT INDICATES THE YEAR’S 6-MONTH PERIOD. - 2ND DIGIT INDICATES THE WEEK NUMBER IN THE 6-MONTH PERIOD. - 3RD & 4TH DIGITS INDICATE SPECIFIC LOT FOR THE WEEK. 6-MONTH PERIOD CODES: A = JAN-JUN 2009 C = JAN-JUN 2010 E = JAN-JUN 2011 B = JUL-DEC 2009 D = JUL-DEC 2010 F = JUL-DEC 2011 EXAMPLE: ARBC - 1ST DIGIT ‘A’ = JAN-JUN 2009 - 2ND DIGIT ‘R’ = WEEK 18; WEEK OF APRIL 27 - 3RD & 4TH DIGITS ‘BC’ = LOT SPECIFIC INFORMATION *TRANSITION FROM FULTEC TRADEMARK AND LOT CODE TO BOURNS TRADEMARK AND DATE CODE IN 2009.

Specifi cations are subject to change without notice. Customers should verify actual device performance in their specifi c applications. P40-G Series TBU® High-Speed Protectors Packaging Specifi cations (per EIA468-B) B A D C N F G (MEASURED AT HUB) USER DIRECTION OF FEED CENTER LINES OF CAVITY EMBOSSMENT t D TOP COVER TAPE E W P DIMENSIONS: MM (INCHES) Device A B C D G N P40-G240 326 (12.835) 330.25 (13.002) 1.5 (.059) 2.5 (.098) 12.8 (.504) 13.5 (.531) 20.2 (.795) - 12.4 (.488) 102 (4.016) Device A0 B 0 D D 1 E F P40-G240 4.2 (.165) 4.4 (.173) 4.2 (.165) 4.4 (.173) 1.5 (.059) 1.6 (.063) 1.5 (.059) - 1.65 (.065) 1.85 (.073) 5.45 (.216) 5.55 (.219) Device K0 P P 0 P 2 t W P40-G240 1.05 (.041) 1.25 (.049) 7.9 (.311) 8.1 (.319) 3.9 (.159) 4.1 (.161) 1.9 (.075) 2.1 (.083) 0.25 (.010) 0.35 (.014) 11.7 (.461) 12.3 (.484) QUANTITY: 3000 PIECES PER REEL

1 µs/div. 400 V/div. 200 mA/div. Ch1 V1 Ch3 Current Model P40-G Series - High Speed Surge Protectors Reference Application A cost-effective protection solution combines the Bourns® TBU® protection device with a diode bridge on the driver side of the transformer and GDTs on the line side. The GDT should have a minimum DCBD of 900 V and a maximum sparkover voltage of 1600 V. The diagram below illustrates a common confi guration of these components. The graph demonstrates the operational characteristics of the circuit. Common Confi guration Diagram - xDSL Protection

5000 V Lightning 2/10 μsec, 500 A

REV. 04/12 “TBU” is a registered trademark of Bourns, Inc. in the United States and other countries. Specifi cations are subject to change without notice. Customers should verify actual device performance in their specifi c applications. P40-G Series TBU® High-Speed Protectors Ch1 P40 VCC P40-G Ch3 Asia-Pacifi c: Tel: +886-2 2562-4117 • Fax: +886-2 2562-4116 Europe: Tel: +41-41 768 5555 • Fax: +41-41 768 5510 The Americas: Tel: +1-951 781-5500 • Fax: +1-951 781-5700 www.bourns.com