P3034 ETAL | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 4
Technical content
ETALDOC 458/10 Page 1 of 4 April 2005 PRODUCT DATA SHEET LINE MATCHING TRANSFORMER P3034 Features Applications ∗ Low Distortion ∗ Telecommunications ∗ Lead-free (Pb-free) ∗ V.34plus modems ∗ RoHS compliant ∗ Portable computers ∗ 12.6mm (0.5") seated height ∗ Fax / modems ∗ Vacuum encapsulated ∗ IEC 60950 and UL 60950 Certified ∗ UL Recognized Component
DESCRIPTION
P3034 is intended for V.34plus applications where low distortion at moderate power levels is required at a competitive price. P3034 is a drop-in replacement for industry standard P1200 for circuits to be upgraded to V.34plus (33,600 bits/second). P3034 is also mechanically and electrically compatible with P2001. P3034 meets international safety standards, being vacuum encapsulated and 100% tested to withstand 6.5kV DC. The part is completely lead-free, compliant with RoHS Directve 2002/95/EC, and suitable for lead-free and conventional processing. P3034 is certified to IEC 60950 and UL 60950. P3034 is a UL Recognized Component and is supported an IEC CB Test Certificate.
ETALDOC 458/10 Page 2 of 4 April 2005 SPECIFICATIONS Electrical At T = 25ºC and as circuit fig. 2 unless otherwise stated. Parameter Conditions Min Typ Max Units Insertion Loss f = 2kHz, RL = 560Ω - - 1.5 dB Frequency response LF-3dB cutoff HF-3dB cutoff 200Hz - 4kHz ±0.2 Hz kHz dB Return Loss 200Hz - 4kHz 18 - - dB Third Harmonic Distortion (1) 450Hz 0dBm in line 300Hz -10dBm 600Hz -10dBm -78 –92 -105 dBm dBm dBm Balance DC – 5kHz Method TG25 80 - - dB Saturation Excitation 50Hz 250V rms. Output voltage across line Vrms Vpeak Voltage isolation (2) 50Hz DC 3.88 5.5 kVrms kV Operating range: Functional Storage Ambient temperature -40 +70 +125 ºC ºC Lumped equivalent circuit parameters as Fig. 1 DC resistance, RDC (3) Sum of windings 120 - 148 Ω Leakage inductance ΔL 14.5 - 19 mH Shunt inductance Lp (4) 10mV 200Hz 4.5 6 - H Shunt loss Rp (4) 10mV 200Hz 12 18 - kΩ Notes 1. Third harmonic typically exceeds other harmonics by 20dB. 2. Components are 100% tested at 6.5kV DC. 3. Caution: do not pass DC through windings. Telephone line current, etc. must be diverted using choke or semiconductor line hold circuit. 4. At signal levels greater than 100mV, Lp will increase and Rp will decrease slightly but the effect is usually favourable to the return loss characteristic. E quivalent Circuit Fi g . 1 IDEAL 1:1 LINE EQ UIPMENT ½ L ½ L½ R½ R
ETALDOC 458/10 Page 3 of 4 April 2005 MATCHING RECOMMENDATIONS CONSTRUCTION Dimensions shown are in millimetres (inches). Geometric centres of outline and pin grid coincide within a tolerance circle of 0.6mm Windings may be used interchangeably as primary or secondary. R ecommended Circuit Fi g . 2 560LINE 600 * If return loss > 16dB , 300Hz - 4kHz is acceptable, blocking capacitor may be relaxed to 4.7 F 33nF27nF 5%+_ 2%+_ μ *+5 0 % 20%_μ6.8 F +5 0 % 20%_ 5%+_
600 MATCHΩ
Figure 3 gives flat RX and TX responses against the CTR21 complex reference impedance (typically around ±0.5dB 300Hz - 3.4kHz). Return loss is typically better than 20dB. The circuit values in parentheses give optimum flatness at a small sacrifice in return loss. For circuits with existing board drillings, figure 4 gives good return loss (>20dB) and RX flatness against the CTR21 complex reference impedance, but TX flatness is degraded by the use of this topology. EUROPEAN CTR21 COMPLEX MATCH R ecommended Circuit Fi g . 3 150 (220) LINE 270 750 750 (680)56nF (150nF ) 100nF150nF μ2.2 F Fi g . 4 820 LINE 270 750 330 27nF 68nF 150nF μ2.2 F
ETALDOC 458/10 Page 4 of 4 April 2005 SAFETY CERTIFICATION Constructed in accordance with IEC 60950-1, EN 60950-1, supplementary insulation, and UL 60950-1, reinforced insulation, 250Vrms maximum working voltage, flammability class V-0. Distances through solid insulation 0.4mm minimum. Certified under the IEC CB scheme (Certificate DK-8570) to IEC 60950-1-2001, sub-clauses 1.5, 1.5.1, Sweden national deviations) for a maximum working voltage of 250Vrms, nominal mains supply voltage not exceeding 300Vrms and a maximum operating temperature of 70ºC in Pollution Degree 2 environments, supplementary insulation. Recognized under the Component Recognition Program of Underwriters Laboratories Inc. to US and Canadian requirements CAN/CSA C22.2 No. 60950-1-03/UL60950-1, First Edition, based on IEC 60950-1, First Edition, maximum working voltage 250Vrms, Pollution Degree 2, reinforced insulation. UL File number E203175. Additionally, Profec Technologies certifies all transformers as providing voltage isolation of 3.88kVrms, 5.5kV DC minimum. All shipments are supported by a certificate of conformity to current applicable safety standards ABSOLUTE MAXIMUM RATINGS COPYRIGHT (Ratings of components independent of circuit). Short term isolation voltage (1s) DC current Storage temperature Lead temperature, 10s 4.6kVrms, 6.5kV DC 100μA -40ºC to +125ºC 260ºC ETAL, P1200, P2001 and P3034 are Trade Marks of Profec Technologies Ltd. The Trade Mark ETAL is registered at the UK Trade Marks Registry. Profec Technologies Ltd. is the owner of the design right under the Copyright Designs and Patents Act 1988 and no rights or licences are hereby granted or implied to any third party. © 1996 - 2005 Profec Technologies Ltd. Reproduction prohibited. ETAL Group Oy, Kuormatie 14, FIN-03101, Nummela Telephone: +358 (0)20 7500 330 Fax: +358 (0)20 7500 333 Website: www.etalgroup.com Email: etalgroup@egruppen.com FM 25326 ISO 9001 E 203175