P2001 ETAL | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 5
Technical content
ETALDOC 100/17 Page 1 of 5 February 2006 PRODUCT DATA SHEET LINE MATCHING TRANSFORMER P2001 Features Applications ∗ Ultra Low Distortion ∗ Telecommunications ∗ Lead-free (Pb-free) ∗ V.34modems ∗ RoHS compliant ∗ Portable computers ∗ 12.6mm (0.5") seated height ∗ Fax / modems ∗ Vacuum encapsulated ∗ IEC 60950 and UL 60950 Certified ∗ UL Recognized Component
DESCRIPTION
P2001 is the transformer of choice in high-speed applications where good performance in a robust resin encapsulated package is required at a most competitive price. P2001 meets international safety standards, being vacuum encapsulated and 100% tested to withstand 6.5kV DC. The part is completely lead-free, compliant with RoHS Directive 2002/95/EC, and suitable for lead-free and conventional processing. P2001 is ideal for datacommunications at V.34 (33,600 bits/second) and is a drop-in replacement for industry standard P1200 for circuits to be upgraded for high speed. P2001 is certified to IEC 60950 and UL 60950. P2001 is a UL Recognized Component and is supported by an IEC CB Test Certificate.
ETALDOC 100/17 Page 2 of 5 February 2006 SPECIFICATIONS Electrical At T = 25ºC and as circuit fig. 2 unless otherwise stated. Parameter Conditions Min Typ Max Units Insertion Loss f = 2kHz, RL = 560Ω - - 1.5 dB Frequency response LF-3dB cutoff HF-3dB cutoff 200Hz - 4kHz ±0.2 Hz kHz dB Return Loss 200Hz - 4kHz 18 - - dB Third Harmonic Distortion (1) 450Hz 0dBm in line 600Hz –10dBm -85 -105 dBm dBm Balance DC – 5kHz Method TG25 dB Saturation Excitation 50Hz 250V rms. Output voltage across line Vrms Vpeak Voltage isolation (2) 50Hz DC 3.88 5.5 kVrms kV Operating range: Functional Storage Humidity Ambient temperature -25 -40 +85 +125 ºC ºC %R.H. Lumped equivalent circuit parameters as Fig. 1 DC resistance, RDC (3) Sum of windings 118 - 146 Ω Leakage inductance ΔL 15 - 19 mH Shunt inductance Lp (4) 200Hz 10mV 4.5 15 H Shunt loss Rp (4) 200Hz 10mV 14 - 40 kΩ Notes 1. Third harmonic typically exceeds other harmonics by 20dB. 2. Components are 100% tested at 6.5kV DC. 3. Caution: do not pass DC through windings. Telephone line current, etc. must be diverted using choke or semiconductor line hold circuit. 4. At signal levels greater than 100mV, Lp will increase and Rp will decrease slightly but the effect is usually favourable to the return loss characteristic. E quivalent Circuit IDE AL 1:1 Fi g 1 LINE MODE M
ETALDOC 100/17 Page 3 of 5 February 2006 PERFORMANCE CHARACTERISTICS -14 -22 -26 -30 100Hz 200 300 500 Typical Wo r st C a se 1kHz 2 Fr e q u e n c y dB 34 5 10 -18 Re t u r n Lo ss Fi g 4 -0.2 -0.3 -0.4 100Hz 200 300 500 1kHz 2 Fr e q u e n c y dB 34 5 10 -0.1 Typical Worst Case F requency R esponse Fi g 3 Re c o m m e n d e d C i r c u i t Fi g 2 560LINE 600 * If return los s > 16dB , 300Hz - 4kHz is acceptable, blocking capacitor may be relaxed to 4.7 F µ 33nF27nF 5%+_ 2%+_ *+5 0 % 20%_µ6.8 F +5 0 % 20%_ 5%+_
600 MATCHΩ EUROPEAN CTR21 COMPLEX MATCH
Figure 5 gives flat RX and TX responses against the reference impedance (typically around 0.5dB 300Hz - 3.4kHz). Return loss is typically better than 20dB. The circuit values in parentheses give optimum flatness at a small sacrifice in return loss. For circuits with existing board drillings, figure 6 gives good return loss (>20dB) and RX flatness against the reference impedance, but TX flatness is degraded by the use of this topology. Re c o m m e n d e d C i rc u i t Fi g 5 150 (220) LINE 270 750 750 (680)56nF (150nF ) 100nF150nF µ2.2 F Re c o m m e n d e d C i rc u i t Fi g 6 820 LINE 270 750 330 27nF 68nF 150nF µ2.2 F
ETALDOC 100/17 Page 4 of 5 February 2006 PERFORMANCE CHARACTERISTICS Notes 1. Figure 7 - to obtain harmonic distortion power in dBm, add fundamental power in dBm to third harmonic in dBc e.g. at -10dBm power in line at 450Hz third harmonic power is -10+ (-96) = -106dBm typical. 2. Third order intermodulation products 2fa-fb and 2fb-fa are of most importance and are significantly greater than products 2fa+fb and 2fb+fa. Figure 8 gives the total power of all distortion products within the voiceband. CONSTRUCTION Dimensions shown are in millimetres (inches). Geometric centres of outline and pin grid coincide within a tolerance circle of 0.6mm Windings may be used interchangeably as primary or secondary. TypicalFu n d a m e n t a l 450H z -84 -80 -88 -92 -96 -10 -5 Fu n d a m e n t a l Po w e r (d Bm ) Th i r d Ha r m o n i c d Bc 0+ 5 T hird Harmonic Distortion vs. S ignal L evel Fi g 7 500+ 600Hz 1.6kHz+ 2.0kHz Fu n d a m e n t a l Po w e r (d Bm ) Dis tortion P ower in 200Hz - 4kHz bandwidth
2 Tone Intermodulation P roducts
vs . S ignal L evelFi g 8 -80 -70 -90 -100 -10 -8 -6 -4 dB m -2 0
ETALDOC 100/17 Page 5 of 5 February 2006 SAFETY CERTIFICATION Constructed in accordance with IEC 60950-1:2001, EN 60950-1:2001 and UL 60950-1 First Edition, supplementary insulation, 250Vrms maximum working voltage, flammability class V-0. Distances through solid insulation 0.4mm minimum. Certified under the IEC CB scheme (Certificate DK-9431) to IEC 60950-1:2001, sub-clauses 1.5, maximum working voltage of 250Vrms, nominal mains supply voltage not exceeding 300Vrms and a maximum operating temperature of 85ºC in Pollution Degree 2 environments, supplementary insulation, including national differences for Denmark, Finland, Germany, Norway, Sweden, Switzerland, USA, Canada and UK. Recognized under the Component Recognition Program of Underwriters Laboratories Inc. to US and Canadian requirements CAN/CSA C22.2 No. 60950-1-03/UL60950-1, First Edition, based on IEC 60950-1, First Edition, maximum working voltage 250Vrms, Pollution Degree 2, reinforced insulation. UL File number E203175. Additionally, Profec Technologies certifies all transformers as providing voltage isolation of 3.88kVrms, 5.5kV DC minimum. All shipments are supported by a certificate of conformity to current applicable safety standards. ABSOLUTE MAXIMUM RATINGS COPYRIGHT (Ratings of components independent of circuit). Short term isolation voltage (15s) DC current Storage temperature Lead temperature, 10s 4.6kVrms, 6.5kV DC 100μA -40ºC to +125ºC 260ºC ETAL, P1200 and P2001 are Trade Marks of Profec Technologies Ltd. The Trade Mark ETAL is registered at the UK Trade Marks Registry. Profec Technologies Ltd. is the owner of the design right under the Copyright Designs and Patents Act 1988 and no rights or licences are hereby granted or implied to any third party. © 1996 - 2006 Profec Technologies Ltd. Reproduction prohibited. ETAL Group Oy, Kuormatie 14, FIN-03101, Nummela Telephone: +358 (0)20 7500 330 Fax: +358 (0)20 7500 333 Website: www.etalgroup.com Email: etalgroup@egruppen.com FM 25326 ISO 9001 E 203175