DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 6

Technical content

ORIGINATOR: C. ENG Date: 7/8/2011 DOCUMENT NO. DOC002326 REV A P1RX4C-SX4x-01MM Product Specification SHEET 1 OF 6 P1RX4C-SX4-01MM Product Specification Sheet

ORIGINATOR: C. ENG DATE: 7/8/2011 DOCUMENT NO. DOC002326 REV A P1RX4C-SX4x-01MM Product Specification SHEET 2 OF 6

1.0 Features

  • Multiple signals from one Multimode fiber
  • Integrated TIA and Limiting Amp
  • Metal enclosure with SC optical interface
  • CML outputs This device is EXTREMELY SENSITIVE to Electrostatic Discharge (ESD). At a minimum, all handling must be performed in accordance with an ANSI-compliant ESD Control Program (ANSI/ESD S20.20-2007) to mitigate possible ESD-induced damage. Reliability and life of the device will be adversely affected if these precautions are not met. This device is a Class 3R Laser device (per IEC 60825-1:2007) and can cause damage to eye sight if used improperly. Refer to ANSI Z136 for proper handling and usage of Class 3R devices.

ORIGINATOR: C. ENG DATE: 7/8/2011 DOCUMENT NO. DOC002326 REV A P1RX4C-SX4x-01MM Product Specification SHEET 3 OF 6

2.0 Absolute Maximum Ratings

Parameter Symbol Min Typ Max Units Storage Temperature 1, 3 Tst °C 3.3V Supply Voltage VCC1 V Operating Surface Temperature 2 Ta °C Operating Humidity 3 RH % Durability – SC Connector 200 cycles Durability – Plug-down Connector 50 cycles

3.0 Optical Characteristics

Parameter (per channel) Symbol Min Typ Max Units Wavelength – Lane 0 778 nm Wavelength – Lane 1 800 nm Wavelength – Lane 2 825 nm Wavelength – Lane 3 850 nm Data Rate per Channel 4 P1RX4C-SX4V-01 P1RX4C-SX4D-01 DR Gb/s Peak Optical Input Power Pin dBm OMA Sensitivity 5 -16.00 dBm

4.0 Electrical Specifications

1 Stresses listed may be applied without causing damage. Functionality at or above the values listed is not implied. Exposure to these values for extended periods may affect reliability. 2 See outline drawing for measurement point. 3 Non condensing, 80% RH. 4 Requires DC-balanced data pattern and max run rate of 80 bits. Measured with input signals conforming to HDMI rev 1.3a, section 4.2.5, figure 4-20. 5 Optical Modulation Amplitude. Based on an unstressed input signal.

6 Based on a jitter-free source

7 CML interface through a 100-ohm differential load.

8 This output is asserted low when a loss of signal is detected on all Lanes

Parameter Symbol Min Typ Max Units Low Frequency Cutoff F CUTOFF 175 kHz Total Jitter (RMS), per lane 6 T J1 10 ps Differential Output Voltage 7 V OD 500 mVp-p Loss of Signal Assert Sensitivity LOS SEN-ON -14.50 dBm Loss of Signal De-Assert Sensitivity LOS SEN-OFF -13.00 dBm Loss of Signal Output Low 8 V LOS V Loss of Signal Output High VLOS V Operating Supply Voltage VCC 3.30 V Operating Supply Current ICC 127 mA

ORIGINATOR: C. ENG DATE: 7/8/2011 DOCUMENT NO. DOC002326 REV A P1RX4C-SX4x-01MM Product Specification SHEET 4 OF 6

5.0 Pin Numbers and Descriptions

The RX-SX4 plugs into a 30 pin connector. For information on the specifications of the connector, contact Hirose (DF12(4.0)-30DP-0.5V(86)). Pin # Signal Description

1 GND Ground

2 LOS Global Loss of Signal Indicator

3 +TD0 Positive Data Output (778nm)

4 NC No Connect 9

5 -TD0 Negative Data Output (778nm)

6 NC No Connect 9

7 +TD1 Positive Data Output (800nm)

8 NC No Connect 9

9 -TD1 Negative Data Output (800nm)

10 NC No Connect 9

11 +TD2 Positive Data Output (825nm)

12 NC No Connect 9

13 -TD2 Negative Data Output (825nm)

14 NC No Connect 9

15 +TD3 Positive Data Output (850nm)

16 NC No Connect 9

17 -TD3 Negative Data Output (850nm)

18 NC No Connect 9

19 GND Ground

20 NC No Connect 9

21 NC No Connect 9

22 NC No Connect 9

23 NC No Connect 9

24 NC No Connect 9

25 NC No Connect 9

26 NC No Connect 9

27 NC No Connect 9

28 VCC 3.3 volt input.

29 GND Ground

30 VCC 3.3 volt input.

6.0 Laser Safety

The P1RX4-SX4x-01 meets Class-3 requirements. 9 NC = No Connect. Do not connect anything to this pin.

ORIGINATOR: C. ENG DATE: 7/8/2011 DOCUMENT NO. DOC002326 REV A P1RX4C-SX4x-01MM Product Specification SHEET 5 OF 6

7.0 Environmental Standards

Omron Network Products designs and manufactures its products to minimize the negative impact on our environment. As such, the P1RX4C-SX4-01MM conforms to a variety of environmental and safety standards Standard Compliant Certificate Available RoHS Yes Yes

ORIGINATOR: C. ENG DATE: 7/8/2011 DOCUMENT NO. DOC002326 REV A P1RX4C-SX4x-01MM Product Specification SHEET 6 OF 6 Dimensions The SX4 ROSA is designed to work with a standard SC ferrule only. Insertion of any other type may result in damage. Dimensions (mm) and orientation are for reference only. Temperature measurement point