P1165

P1165 ETAL | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 7

Technical content

ETALDOC 78/22 Page 1 of 5 February 2006 PRODUCT DATA SHEET LOW PROFILE LINE P1165 MATCHING TRANSFORMER Features Applications ∗ Low Profile (11mm) ∗ Telecommunications ∗ Lead-free (Pb-free) ∗ Modems to V.34 ∗ RoHS compliant ∗ Line matching ∗ Vacuum encapsulated ∗ Portable computers ∗ IEC 60950 and UL 60950 certified ∗ Fax/modems ∗ UL Recognized Component ∗ Instrumentation ∗ High Thermal Stability ∗ Voice

DESCRIPTION

P1165 is intended for data communications at V.32bis (14,400 bits/second) data rates. With careful circuit design, P1165 may be used for V.34 applications to 33,600 bits/second or higher. P1165 is specifically designed to be easily matched to both 600ohm and complex impedance telephone lines, using a minimum of external components. P1165 also exhibits stable characteristics over its operating temperature range to maximize data throughput under varying environmental conditions without the need for modem retraining. P1165 is certified to IEC 60950 and UL 60950. P1165 is a UL Recognized Component and is supported by an IEC CB Test Certificate. The part is completely lead-free, compliant with RoHS Directive 2002/95/EC, and suitable for lead-free and conventional processing.

ETALDOC 78/22 Page 2 of 5 February 2006 SPECIFICATIONS Electrical At T = 25ºC and as circuit fig. 2 unless otherwise stated. Parameter Conditions Min Typ Max Units Insertion Loss f = 2kHz, RL = 560Ω - - 1.5 dB Frequency response LF-3dB cutoff HF-3dB cutoff 200Hz - 4kHz ±0.2 Hz kHz dB Return Loss 200Hz - 4kHz 18 - - dB Distortion (1) 0dBm in line, 3 rd Harmonic f = 600Hz f = 450Hz -76 -75 -72 -70 dBm dBm Balance DC – 5kHz Method TG25 dB Saturation Excitation 50Hz 250V rms. Output voltage across line V rms V peak Voltage isolation (2) 50Hz DC 3.88 5.5 kVrms kV Operating range: Functional Storage Humidity Ambient temperature -25 –40 +85 +125 ºC ºC %R.H. Lumped equivalent circuit parameters as Fig. 1 DC resistance, RDC (3) Sum of windings 108 - 132 Ω Leakage inductance ΔL 6.5 - 7.5 mH Shunt inductance Lp (4) 100mV 200Hz 100mV 1kHz 2.25 2.5 H H Shunt loss Rp (4) 10mV 200Hz 10mV 1kHz kΩ kΩ Notes 1. Third harmonic typically exceeds other harmonics by 20dB. 2. Components are 100% tested at 6.5kV DC. 3. Caution: do not pass DC through windings. Telephone line current, etc. must be diverted using choke or semiconductor line hold circuit. 4. At signal levels greater than 100mV, Lp will increase and Rp will decrease slightly but the effect is usually favourable to the return loss characteristic. E quivalent Circuit Fi g . 1 IDEAL 1:1 LINE EQ UIPMENT ½ L ½ L½ R½ R

ETALDOC 78/22 Page 3 of 5 February 2006

ETALDOC 78/22 Page 4 of 5 February 2006 PERFORMANCE CHARACTERISTICS EUROPEAN CTR21 COMPLEX MATCH R ecommended Circuit Fi g 5 100 LINE 270 750 910 27nF 100nF150nF μ2.2 F R ecommended Circuit Fi g 2 LINE 600 * If re turn lo ss > 1 6d B, 30 0 Hz - 4 kHz is a c c e p ta b le , b lo c kin g capacitor may be relaxed to μ6.8 F +5 0 20 %*

6.8 F +5 0

20_

600 MATCHΩ

18nF 5% 680 10% 560 2% Re c o m m e n d e d C i rc u i t Fi g 6 910 LINE 270 750 330 82nF 150nF μ2.2 F -0.2 -0.3 -0.4 100Hz 200 300 500 1kHz 2 F requency dB 34 5 10 -0.1 Typical Worst Case F requency R esponse Fi g 3 Figure 5 gives flat RX and TX responses against the reference impedance (typically around 0.5dB 200Hz - 4kHz). Return loss is typically better than 20dB. The 150nF capacitor should be of a temperature stable dielectric. In practice, the 100ohm resistor will normally connect to a low impedance TX output. For circuits with existing board drillings, figure 6 gives good return loss (>20dB) against the reference impedance, but TX and RX flatness are degraded by the use of this topology. For recommended matching to other reference impedances please contact ETAL. -14 -22 -26 -30 100Hz 200 300 500 Typical Wo r st C a se 1kHz 2 F requency dB 34 5 10 -18 Re t u rn Lo ss Fi g 4 TypicalFu n d a m e n t a l 450Hz -74 -72 -76 -78 -80 -10 -5 Fu n d a m e n t a l Po w e r (d Bm ) T hird Harmonic dBc 0+ 5 T hird H armonic Dis tortion vs . S ignal L evel Fi g 7 500+ 600Hz Typical 1.6kHz+ 2.0kHz Total power in line (dB m) Distortion P ower in 200H z - 4kHz bandwidth

2 Tone Intermodulation P roducts

vs. S ignal L evelFi g 8 -70 -60 -80 -90 -10 -8 -6 -4 dB m -2 0

ETALDOC 78/22 Page 5 of 5 February 2006 CONSTRUCTION Dimensions shown are in millimetres (inches). Geometric centres of outline and pin grid coincide within a tolerance circle of 0.6mm Windings may be used interchangeably as primary or secondary. SAFETY CERTIFICATION Constructed in accordance with IEC 60950-1:2001, EN60950-1:2001 and UL 60950-1 First Edition, s upplementary insulation, 250Vrms maximum working voltage, flammability class V-0. Distances through solid insulation 0.4mm minimum. Certified under the IEC CB scheme (Certificate DK-9431) to IEC 60950-1:2001, sub-clauses 1.5, maximum working voltage of 250Vrms, nominal mains supply voltage not exceeding 300Vrms and a maximum operating temperature of 85ºC in Pollution Degree 2 environments, supplementary insulation, including national differences for Denmark, Finland, Germany, Norway, Sweden, Switzerland, USA, Canada and UK. Recognized under the Component Recognition Program of Underwriters Laboratories Inc. to US and Canadian requirements CAN/CSA C22.2 No. 60950-1-03/UL60950-1, First Edition, based on IEC 60950-1, First Edition, maximum working voltage 250Vrms, Pollution Degree 2, reinforced insulation. UL File number E203175. Additionally, Profec Technologies certifies all transformers as providing voltage isolation of 3.88kVrms, 5.5kV DC minimum. All shipments are supported by a Certificate of Conformity to current applicable safety standards.

ETALDOC 78/22 Page 6 of 5 February 2006

ETALDOC 78/22 Page 7 of 5 February 2006 ABSOLUTE MAXIMUM RATINGS COPYRIGHT (Ratings of components independent of circuit). Short term isolation voltage (2s) DC current Storage temperature Lead temperature, 10s 4.6kVrms, 6.5kV DC 100μA -40ºC to +125ºC 260ºC ETAL, and P1165 are Trade Marks of Profec Technologies Ltd. The Trade Mark ETAL is registered at the UK Trade Marks Registry. Profec Technologies Ltd. is the owner of the design right under the Copyright Designs and Patents Act 1988 and no rights or licences are hereby granted or implied to any third party. © 1997 - 2006 Profec Technologies Ltd. Reproduction prohibited. ETAL Group Oy, Kuormatie 14, FIN-03101, Nummela Telephone: +358 (0)20 7500 330 Fax: +358 (0)20 7500 333 Website: www.etalgroup.com Email: etalgroup@egruppen.com FM 25326 ISO 9001 E 203175