DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 5

Technical content

SIDACtor® Protection Thyristors Revised: February 22, 2011 © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. Broadband Optimized™ Protection Q2L Series - 3x3 QFN

Electrical Characteristics

Description

Features and Benefits Part Number Marking VDRM @lDRM=5μA VS @100V/μs IH IS IT VT@ IT = 2.2Amps Capacitance @1MHz, 2V bias V min V max mA min mA max A max V max pF min pF max P0080Q12ALRP P-8A 6 25 50 800 2.2 5 25 55 P0300Q12ALRP P03A 25 40 50 800 2.2 5 15 35 P0640Q12ALRP P06A 58 77 150 800 2.2 5 40 60 P0720Q12ALRP P07A 65 88 150 800 2.2 5 40 60 P0900Q12ALRP P09A 75 98 150 800 2.2 5 35 55 P1100Q12ALRP P11A 90 130 150 800 2.2 5 30 50 P1300Q12ALRP P13A 120 160 150 800 2.2 5 25 45 P1500Q12ALRP P15A 140 180 150 800 2.2 5 25 40 P1800Q12ALRP P18A 170 220 150 800 2.2 5 25 35 P2300Q12ALRP P23A 190 260 150 800 2.2 5 25 35 P2600Q12ALRP P26A 220 300 150 800 2.2 5 25 35 P3100Q12ALRP P31A 275 350 150 800 2.2 5 20 35 P3500Q12ALRP P35A 320 400 150 800 2.2 5 20 30 Pinout Designation Agency Approvals Agency Agency File Number E133083 Schematic Symbol Not Applicable t-PXWPMUBHFPWFSTIPPU t-PXPOTUBUFWPMUBHF t-PXDBQBDJUBODF t%PFTOPUEFHSBEFXJUIVTF t4NBMM40GPPUQSJOU t'BJMTTIPSUDJSDVJUXIFO surged in excess of ratings Q2L Series 3x3 QFN are low capacitance SIDACtor® de- vices designed to protect high density broadband equip- ment from damaging overvoltage transients. The series provides a low profile, chip scale surface mount solution that enables broadband equipment to comply with global regulatory standards while limiting the impact to broadband signals and board space. Applicable Global Standards t5*"" t5*"# t*56,&OIBODFE Level* t*56,#BTJD-FWFM t*&$ t(3*OUFSCVJMEJOH t(3*OUSBCVJMEJOH t:%5 t:%5 t:%5 * A/B-Rated parts require series resistance Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are bi-directional (unless otherwise noted). T able continues on next page.

SIDACtor® Protection Thyristors Revised: February 22, 2011 © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. Broadband Optimized™ Protection Surge Ratings Electrical Characteristics (continued) Package Symbol Parameter Value Unit 3x3 QFN TJ Operating Junction Temperature Range UP TS Storage Temperature Range UP R0JA Thermal Resistance: Junction to Ambient 120 °C/W Thermal Considerations Series Ipp ITSM di/dt 2x10μs 1.2x50μs/8x20μs 10x160μs 10x560μs 10x1000μs 50 / 60 Hz A min A min A min A min A min A min A/μs max A1 5 0 1 5 0 9 0 5 0 4 5 2 0 5 0 0 B 250 250 150 100 80 25 500 Part Number Marking VDRM @lDRM=5μA VS @100V/μs IH IS IT VT@ IT = 2.2Amps Capacitance @1MHz, 2V bias V min V max mA min mA max A max V max pF min pF max P0080Q12BLRP P-8B 6 25 50 800 2.2 5 25 55 P0300Q12BLRP P03B 25 40 50 800 2.2 5 15 35 P0640Q12BLRP P06B 58 77 150 800 2.2 5 40 60 P0720Q12BLRP P07B 65 88 150 800 2.2 5 40 60 P0900Q12BLRP P09B 75 98 150 800 2.2 5 35 55 P1100Q12BLRP P11B 90 130 150 800 2.2 5 30 50 P1300Q12BLRP P13B 120 160 150 800 2.2 5 25 45 P1500Q12BLRP P15B 140 180 150 800 2.2 5 25 40 P1800Q12BLRP P18B 170 220 150 800 2.2 5 25 35 P2300Q12BLRP P23B 190 260 150 800 2.2 5 25 35 P2600Q12BLRP P26B 220 300 150 800 2.2 5 25 35 P3100Q12BLRP P31B 275 350 150 800 2.2 5 20 35 P3500Q12BLRP P35B 320 400 150 800 2.2 5 20 30 Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are bi-directional (unless otherwise noted). Notes: - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPPSBUJOHTBQQMJDBCMFPWFSUFNQFSBUVSFSBOHFPG$UP - The device must initially be in thermal equilibrium with -40°C < TJ <

SIDACtor® Protection Thyristors Revised: February 22, 2011 © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. Broadband Optimized™ Protection IH IT IS IDRM VDRMVT +V-V VS 100 tr td Peak Value Half Value t – Time (μs) IPP – Peak Pulse Current – %I PP tr = rise time to peak value td = decay time to half value Waveform = t r x td V-I Characteristics tr x td Pulse Waveform -40 -20 0 20 40 60 80 100 120 140 160 Junction Temperature (TJ) – °C Percent of VS Change – % 25 °C 25°C Case Temperature (TC) - ºC 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 Ratio of IH IH (TC = 25ºC) Normalized VS Change vs. Junction T emperature Normalized DC Holding Current vs. Case T emperature Soldering Parameters Reflow Condition Pb-Free assembly (see Fig. 1) Pre Heat - Temperature Min (Ts(min)) - Temperature Max (Ts(max)) - Time (Min to Max) (ts) 60-180 secs. Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) - Temperature (tL) 60-150 secs. Peak Temp (TP) Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed Time T emperature TP TL TS(max) TS(min) tP tL tS time to peak temperature (t 25ºC to peak) Ramp-down Ramp-up Preheat Critical Zone TL to TP Figure 1

SIDACtor® Protection Thyristors Revised: February 22, 2011 © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. Broadband Optimized™ Protection Dimensions Inches Millimeters Min Max Min Max A 0.114 0.122 2.900 3.100 B 0.114 0.122 2.900 3.100 C 0.075 0.083 1 .900 2.100 E 0.011 0.019 0.285 0.485 F 0.076 0.084 1 .930 2.130 H 0.035 0.043 0.900 1 .100 J 0.000 0.008 0.000 0.200 K1 0.004 0.012 0.100 0.300 K2 0.004 0.012 0.100 0.300 M1 0.056 0.064 1 .430 1 .630 M2 0.038 0.046 0.970 1 .170 N1 0.096 0.104 2.440 2.640 N2 0.082 0.090 2.080 2.280 2.54 (.100”) H 1.50 (.059”) 1 .27 (.050”) K1N2 END VIEW SIDE VIEW F E C J B A TOP VIEW BOTTOM VIEW Recommended Soldering Pad Outline (Reference Only) Dimensions — 3x3 QFN Physical Specifications Environmental Specifications Lead Material Copper Alloy T erminal Finish 100% Matte-Tin Plated Body Material UL recognized epoxy meeting flammability classification 94V-0 Part Numbering CONSTRUCTION VARIABLE REEL PACK IPP RATING PACKAGE TYPE RoHS COMPLIANT TYPE P = SIDACtor Q12 x L RP MEDIAN VOLTAGE P xxx 0 Part Marking Code (Refer to Electrical Characteristics Table) Date codeXXXXX XXXX Terminals on Back XXXX XXXXX Part Marking High T emp Voltage Blocking 80% Rated VDRM (VAC Peak ¡$PS 504 or 1008 hrs. MIL -STD-750 (Method 1040) JEDEC, JESD22-A-101 T emp Cycling ¡$UP NJOEXFMM VQUP cycles. MIL -STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased T emp & Humidity 52 V DC VQUPIST&*" JEDEC, JESD22-A-101 High T emp Storage ¡$IST.*-45% .FUIPE JEDEC, JESD22-A-101 Low T emp Storage -65°C, 1008 hrs. Thermal Shock ¡$UP NJOEXFMM TFDUSBOTGFS 10 cycles. MIL -STD-750 (Method 1056) JEDEC, JESD22-A-106 Resistance to Solder Heat TFDT.*-45% .FUIPE Moisture Sensitivity Level IST SFnPXDZDMFT ¡$1FBL +&%&$+45% -FWFM Package Type Description Quantity Added Suffix Industry Standard Q12 3x3 QFN Tape and Reel Pack 5000 RP EIA-481-D Packing Options

SIDACtor® Protection Thyristors Revised: February 22, 2011 © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. Broadband Optimized™ Protection A B D C N Reel Dimension W D1P2 F CARRIER TAPE COVER TAPE T E1 Tape Dimension Items TRAILER 160mm MIN LEADER 400mm MIN CARRIER TAPE COVER TAPE Tape Leader and Trailer Dimensions STARTEND Symbols Description Inches Millimeters Min Max Min Max A Reel Diameter N/A 12.992 N/A 330.0 B Drive Spoke Width 0.059 N/A 1 .50 N/A C Arbor Hole Diameter 0.504 0.531 12.80 13.50 D Drive Spoke Diameter 0.795 N/A 20.20 N/A N Hub Diameter 1 .969 N/A 50.00 N/A W1 Reel Inner Width at Hub 0.488 0.567 12.40 14.40 A0 Pocket Width at bottom 0.126 0.134 3.20 3.40 B0 Pocket Length at bottom 0.126 0.134 3.20 3.40 D0 Feed Hole Diameter 0.059 0.063 1 .50 1 .60 D1 Pocket Hole Diameter 0.059 N/A 1 .50 N/A E1 Feed hole position 1 0.065 0.073 1 .65 1 .85 E2 Feed hole position 2 0.400 0.408 10.15 10.35 F Feed hole center-Pocket hole 0.215 0.219 5.45 5.55 K0 Pocket Depth 0.039 0.051 1 .00 1 .30 P0 Feed Hole Pitch 0.153 0.161 3.90 4.10 P1 Component Spacing 0.311 0.319 7 .90 8.10 Feed hole center-Pocket hole 0.077 0.081 1 .95 2.05 T Carrier Tape Thickness 0.010 0.014 0.25 0.35 W Embossed Carrier Tape Width 0.453 0.484 11 .50 12.30 W0 Cover Tape Width 0.358 0.366 9.10 9.30 T ape and Reel Dimensions — 3x3 QFN