DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

SIDACtor® Protection Thyristors Revised: February 22, 2011 © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. Broadband Optimized™ Protection

Description

MC Series TO-92 are low capacitance SIDACtor® devices designed to protect broadband CPE equipment such as VoIP and DSL Modems from damaging overvoltage transients. The series provides a through-hole solution that enables CPE equipment to comply with global regulatory standards while limiting the impact to broadband signals.Electrical Characteristics Applicable Global Standards Features and Benefits MC Series - TO-92 Agency Approvals Agency Agency File Number E133083 Schematic Symbol Pinout Designation Part Number Marking VDRM @lDRM=5μA VS @100V/μs IH IS IT VT @IT=2.2 Amps Capacitance @1MHz, 2V bias V min V max mA min mA max A max V max pF min pF max P0080ECMCLxxx P0080ECMC 6 25 50 800 2.2 4 35 75 P0300ECMCLxxx P0300ECMC 25 40 50 800 2.2 4 25 45 P0640ECMCLxxx P0640ECMC 58 77 150 800 2.2 4 55 85 P0720ECMCLxxx P0720ECMC 65 88 150 800 2.2 4 50 75 P0900ECMCLxxx P0900ECMC 75 98 150 800 2.2 4 45 70 P1100ECMCLxxx P1100ECMC 90 130 150 800 2.2 4 45 70 P1300ECMCLxxx P1300ECMC 120 160 150 800 2.2 4 40 60 P1500ECMCLxxx P1500ECMC 140 180 150 800 2.2 4 35 55 P1800ECMCLxxx P1800ECMC 170 220 150 800 2.2 4 35 50 P2300ECMCLxxx P2300ECMC 190 260 150 800 2.2 4 30 50 P2600ECMCLxxx P2600ECMC 220 300 150 800 2.2 4 30 45 P3100ECMCLxxx P3100ECMC 275 350 150 800 2.2 4 30 45 P3500ECMCLxxx P3500ECMC 320 400 150 800 2.2 4 25 40 t TIA-968-A t TIA-968-B t ITU K.20/21 Enhanced Level t ITU K.20/21 Basic Level t GR 1089 Inter-building t GR 1089 Intra-building t IEC 61000-4-5 t YD/T 1082 t YD/T 993 t YD/T 950 Pin 1 Pin 3 t Low voltage overshoot t Low on-state voltage t Does not degrade with use t Fails short circuit when surged in excess of ratings t 40% lower capacitance than our Baseband Protectors, for applications that demand greater signal integrity Notes: - Absolute maximum ratings measured at T A= 25ºC (unless otherwise noted). - Devices are bi-directional (unless otherwise noted). - XXX Part Number Suffix: ‘AP’ (Ammo Pack), or ‘RP1’ or ‘RP2’ (Reel Pack),.

SIDACtor® Protection Thyristors Revised: February 22, 2011 © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. Broadband Optimized™ Protection Surge Ratings Series IPP ITSM 50/60 Hz di/dt0.2x310 1 0.5x700 2 2x10 1 2x10 2 8x20 1 1.2x50 2 10x160 1 10x160 2 10x560 1 10x560 2 5x320 1 9x720 2 10x360 1 10x360 2 10x1000 1 10x1000 2 5x310 1 10x700 2 A min A min A min A min A min A min A min A min A min A min A/μs Max C 50 500 400 200 150 200 175 100 200 30 500 Package Symbol Parameter Value Unit TO-92 TJ Operating Junction Temperature Range UP TS Storage Temperature Range UP R0JA Thermal Resistance: Junction to Ambient 90 °C/W Thermal Considerations IH IT IS IDRM VDRMVT +V-V VS 100 tr td Peak Value Half Value t – Time (μs) IPP – Peak Pulse Current – %I PP tr = rise time to peak value td = decay time to half value Waveform = t r x td V-I Characteristics tr x td Pulse Waveform 25°C Case Temperature (TC) - ºC 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 Ratio of IH IH (TC = 25ºC) Normalized VS Change vs. Junction T emperature Normalized DC Holding Current vs. Case T emperature Notes:

1 Current waveform in μs

2 Voltage waveform in μs

  • Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPPSBUJOHTBQQMJDBCMFPWFSUFNQFSBUVSFSBOHFPG$UP - The device must initially be in thermal equilibrium with -40°C < TJ < -40 -20 0 20 40 60 80 100 120 140 160 Junction Temperature (TJ) – °C Percent of VS Change – % 25 °C

SIDACtor® Protection Thyristors Revised: February 22, 2011 © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. Broadband Optimized™ Protection Time T emperature TP TL TS(max) TS(min) tP tL tS time to peak temperature (t 25ºC to peak) Ramp-down Ramp-up Preheat Critical Zone TL to TP Figure 1 Soldering Parameters Physical Specifications Environmental Specifications Lead Material Copper Alloy T erminal Finish 100% Matte-Tin Plated Body Material UL recognized epoxy meeting flammability classification 94V-0 High T emp Voltage Blocking 80% Rated VDRM (VAC Peak ¡$PS 504 or 1008 hrs. MIL -STD-750 (Method 1040) JEDEC, JESD22-A-101 T emp Cycling ¡$UP NJOEXFMM VQUP cycles. MIL -STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased T emp & Humidity 52 V DC VQUPIST&*" JEDEC, JESD22-A-101 High T emp Storage ¡$IST.*-45% .FUIPE JEDEC, JESD22-A-101 Low T emp Storage -65°C, 1008 hrs. Thermal Shock ¡$UP NJOEXFMM TFDUSBOTGFS 10 cycles. MIL -STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker T est) BUN VQUPIST&*" JEDEC, JESD22-A-102 Resistance to Solder Heat TFDT.*-45% .FUIPE Moisture Sensitivity Level IST SFnPXDZDMFT ¡$1FBL +&%&$+45% -FWFM Reflow Condition Pb-Free assembly (see Fig. 1) Pre Heat - Temperature Min (Ts(min)) - Temperature Max (Ts(max)) - Time (Min to Max) (ts) 60-180 secs. Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) - Temperature (tL) 60-150 secs. Peak Temp (TP) Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed Part MarkingPart Numbering CONSTRUCTION VARIABLE PACKING OPTIONS IPP RATING RoHS COMPLIANT TYPE P = SIDACtor P L xxx MEDIAN VOLTAGE PACKAGE TYPE xxx 0 E C MC SERIES MC XXXXXXX XX XXXXX Part Marking Code (Refer to Electrical Characteristics Table) Date Code

SIDACtor® Protection Thyristors Revised: February 22, 2011 © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. Broadband Optimized™ Protection Package Type Description Packing Options Quantity Added Suffix Lead Spacing Industry Standard E TO-92 Tape and Reel Pack 2000 RP1 0.1 inch (2.54mm) EIA-481-D RP2 0.2 inch (5.08mm) TO-92 Ammo Pack AP (Not applicable) EIA-468-B TO-92 Bulk Pack N/A (Not applicable) N/A Packing Options All leads are insulated from case. Case is electri- cally non-conductive. (Rated at 1600 V(AC) RMS for one minute from leads to case over the operating temperature range.) Mold flash shall not exceed 0.13 mm per side. A B Temperature Measurement Point MT2/PIN 3MT1/PIN 1 E H G D K J L M N The TO-92 is designed to meet mechanical standards as set forth in JEDEC publication number 95. Inches Millimeters Min Max Min Max A 0.176 0.196 4.47 4.98 B 0.500 12.70 D 0.095 0.105 2.41 2.67 E 0.150 3.81 G 0.135 0.145 3.43 3.68 H 0.088 0.096 2.23 2.44 J 0.176 0.186 4.47 4.73 K 0.088 0.096 2.23 2.44 L 0.013 0.019 0.33 0.48 M 0.013 0.017 0.33 0.43 N 0.60 1 .52 Dimensions — TO-92 T ape and Reel Specification — TO-92 Inches Millimeters Min Max Min Max A N/A 14.173 N/A 360.0 B 4.016 N/A 102.0 N/A C 3.386 N/A 86.0 N/A D 0.795 N/A 20.2 N/A W1 1 .181 1 .968 30.0 50.0 P 0.496 0.504 12.60 12.80 P0 0.498 0.502 12.65 12.75 F(for RP1) 0.090 0.110 2.29 2.80 F(for RP2) 0.182 0.244 4.63 6.19 H N/A 1 .673 N/A 42.50 H1 N/A 1 .270 N/A 32.26 W 0.67 4 0.763 17 .12 19.38 W2 0.354 0.370 8.25 9.75 W3 0.236 N/A 6.00 N/A W4 0.020 N/A 0.50 N/A Ammo Pack Specification — TO-92 Flat down

25 Devices per fold

0.708 (18.0) 1.27 (32.2) (41.2) MAX 0.50 (12.7) 0.354 (9.0) 0.236 (6.0) 0.02 (0.5) 0.20 (5.08) 0.50 (12.7) 0.25 (6.35) Direction of F eed Dimensions are in inches (and millimeters). 1.7 (43) 12.9 (327) 6.9 (175) 1.7 (43) 0.157 DIA(4.0) A B D C W1 FLAT SIDE OF TO-92 ROUND SIDE OF TO-92 H W W4H1 P P0 F (RP1) F (RP2)