PXXXXDM UNSEMI | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 6
Technical content
Description
Applicable Global Standards ROHS www.unsemi.com.tw Features and Benefits Revision March 1,2022 www.unsemi.com.tw For technical questions, contact: tech@unsemi.com.tw Specifications are subject to change without notice. Please refer to www.unsemi.com.tw for current information.1/5 PXXXXDM Series SOD-123FL(SMF) Thyristor Surge Suppressors (TSS) @10/700μSđ2KV Schematic Symbol Electrical Parameters PXXXXDM Series are designed to protect broadband equipment such as modems, line card, CPE and DSL from damaging over-voltage transients. The series provides a surface mount solution that enables equipment to comply with global regulatory standards Excellent capability of absorbing transient surge Quick response to surge voltage (ns Level) Eliminates over voltage caused by fast rising transients Moisture sensitivity level: Level 1 Weight 69 mg (approximate) Non degenerative Response Time is < 1us ROHS compliant TIA-968-A ITU K.20/21 Enhanced level ITU K.20/21 Basic Level GR 1089 Inter building IEC 61000-4-5 YD/T 1082 Parameter IS lDRM IH IT VS VDRM Vτ Definition Off-state Capacitance - typical capacitance measured in off state On-state Voltage - maximum voltage measured at rated on-state current Peak Off-state Voltage - maximum voltage that can be applied while maintaining off state Switching Voltage - maximum voltage prior to switching to on stat On-state Current - maximum rated continuous on-state bcurrent Holding Current - minimum current required to maintain on state Leakage Current - maximum peak off-state current measured at VDRM Switching Current - maximum current required to switch to on state IS lDRM IH IT VS VDRMVτ +V- V
Revision March 1,2022 www.unsemi.com.tw For technical questions, contact: tech@unsemi.com.tw ROHS Thyristor Surge Suppressors (TSS) @10/700μSđ2KV Specifications are subject to change without notice. Please refer to www.unsemi.com.tw for current information. PXXXXDM Series SOD-123FL(SMF) Electrical Characteristics (@ 25℃ Unless Otherwise Specified ) P0080DM P0300DM P0640DM P0720DM P0900DM P1100DM P1300DM P1500DM P1800DM P2000DM P2300DM P2600DM P3100DM P3500DM P3800DM P4200DM 120 140 170 180 190 220 275 320 360 400 130 160 180 220 220 260 300 350 400 460 520 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 150 150 150 150 150 150 150 150 150 150 150 150 150 150 Part Number P8M 03M 06M 07M 09M 11M 13M 15M 18M 20M 23M 26M 31M 35M 38M 42M Marking pF Typ. V DRM @IDRM=5μA IDRM VS @100V/μS IS VT @IT=2.2A IT CO @1MHzIH Surge Ratings Series 2/10μS¹ 2/10μS² A min 8/20μS¹ 1.2/50μS² A min 10/160μS¹ 10/160μS² A min 100 100 60 10/560μS¹ 10/560μS² A min 10/1000μS¹ 10/1000μS² A min 5/320μS¹ ITSM 50/60HZ10/700μS² di/dt A min A min Amps/µs max 50 10 500 A Notes: 1. Current waveform in µs 2. Voltage waveform in µs Notes: - Vs is measured at 100KV/s - Off-state capacitance is measured in VDC=2V, VRMS=1V, f=1MHz - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPP ratings applicable over temperature range of -40ºC to +85ºC - The device must initially be in thermal equilibrium with -40°C < TJ < +150°C
Revision March 1,2022 www.unsemi.com.tw For technical questions, contact: tech@unsemi.com.tw ROHS Thyristor Surge Suppressors (TSS) Specifications are subject to change without notice. Please refer to www.unsemi.com.tw for current information.4/5 Soldering Parameters ROHS Environmental Specifications Physical Specifications Lead Material Terminal Finish Body Material Copper Alloy 100% Matte-Tin Plated UL recognized epoxy meeting flammability classification 94V-0 High Temp Voltage Blocking 80% Rated VDRM (VAC Peak ) +125°C or +150°C, Lead Material Copper Alloy High Temp Voltage Blocking 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 -65°C to +150°C, 15 min. dwell, 10 up to 100 cycles.MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 52 VDC (+85°C) 85%RH, 504 up to 1008 hrs. EIA/ JEDEC, JESD22-A-101 +150°C 1008 hrs. MIL-STD-750 (Method 1031) JEDEC, JESD22-A-101 85%RH, +85°C, 168 hrs., 3 reflow cycles Level (+260°C Peak). JEDEC-J-STD-020, Level 1 -65°C, 1008 hrs. 0°C to +100°C, 5 min. dwell, 10 sec. transfer, Thermal Shock 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 +121°C, 100%RH, 2atm, 24 up to 168 hrs. EIA/Cooker Test) JEDEC, JESD22-A-102 +260°C, 30 secs. MIL-STD-750 (Method 2031 Biased Temp & Humidity High Temp Storage Low Temp Storage Thermal Shock Autoclave (Pressure Cooker Test) Resistance to Solder Heat Moisture Sensitivity Level Temp Cycing @10/700μSđ2KV PXXXXDM Series SOD-123FL(SMF) TimeTime to peak temperature ( T25℃ to peak) Preheat Ts(min) Ts(max) TL TL TP Temperature Ramp-up Ramp-down Critical Zone TL toTP TP Ts Lead–free assembly +150°C +200°C 60 -180 Seconds 3°C/Second max 5°C/Second max 217°C 60 -150 Seconds 260 +0/-5°C
30 Seconds Max
6°C/Second Max 8 minutes Max +260°C Reflow Condition Pre Heat -Temperature Min (Ts(min)) -Temperature Max (Ts(max)) - Time (min to max) (TS) Average ramp up rate ( Liquidus Temp TL) to peak TS(max) to TL - Ramp-up Rate Reflow - Temperature (TL) (Liquidus) - Time (min to max) (TS) Peak Temperature (TP) Do not exceed Time 25°C to peak Temperature (TP) Time within 5°C of actual peak Temperature (TP) Ramp-down Rate
Thyristor Surge Suppressors (TSS) Revision March 1,2022 www.unsemi.com.tw For technical questions, contact: tech@unsemi.com.tw ROHS Specifications are subject to change without notice. Please refer to www.unsemi.com.tw for current information.5/5 Dimensions ROHS PXXXXDM Series SOD-123FL(SMF) Packaging Tape and Reel Specifications @10/700μS, 2KV PXXXXDM Part Number Component Package SOD-123FL 3000 0.0141 7 inch reel pack Quantity Unit Weight (g/Pcs) typ. Description Ref. InchesMillimeters Min Min A B C D E F G J K L 2.60 1.60 3.45 0.10 0.30 0.80 0.95 1.30 1.30 3.00 2.00 3.95 0.25 0.90 1.20 1.35 1.70 0.102 0.063 0.136 0.004 0.012 0.031 0.037 0.051 0.051 0.118 0.079 0.156 0.010 0.035 0.047 0.053 0.067 Max Max Ref. Dimensions Millimeters Inches A B C D E F G J JK L SOD-123FL P0 P2 E F A0 P1 W BO C DO E F W 1.95 ± 0.3 3.95 ± 0.3 178 1.55 ± 0.1 1.75 ± 0.2 13.3 ± 0.3 3.50 ± 0.2 4.00 ± 0.2 4.00 ± 0.2 2.00 ± 0.2 8.0 ± 0.2 11.5 ± 1.0 0.077 ± 0.012 0.156 ± 0.012 7.0 0.061 ± 0.004 0.069 ± 0.008 0.524 ± 0.012 0.138 ± 0.008 0.157 ± 0.008 0.157 ± 0.008 0.079 ± 0.008 0.315 ± 0.008 0.453 ± 0.039
Revision March 1,2022 www.unsemi.com.tw For technical questions, contact: tech@unsemi.com.tw ROHS Specifications are subject to change without notice. Please refer to www.unsemi.com.tw for current information. Disclaimer ROHS UNSEMI RESERVES THE RIGHT TO MAKE CHANGE ON OUR PRODUTS , PRODUCTS SPECIFICATION AND DATA WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. UN SEMICONDUCTOR LIMITED its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “UNSEMI”)does not give any representations or warranties for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. In no event shall UNSEMI be liable for any indirect, incidental, punitive, special or consequential damages (including any and all implied warranties, warranties of fitness for particular purpose, non-infringement and merchantability.) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Statements regarding the suitability of products for certain types of applications are based on UNSEMI knowledge of typical requirements that are often placed on UNSEMI products in generic applications. Such statements are not binding, statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify UNSEMI's terms and conditions of purchase, including but not limited to the warranty expressed therein. Unless otherwise agreed in writing, UNSEMI product is not designed, authorized or warranted to be suitable for use in medical life-saving, or life-sustaining application , nor in applications where failure or malfunction of a UNSEMI product can reasonably be expected to result in personal injury, death or severe property or environmental damage. UNSEMI and its suppliers accept no liability for inclusion or use of UNSEMI products in such equipment or applications and therefore such inclusion and/or use is at the customer's own risk. All referenced brands, product names, service names and trademarks are the property of their respective owners.