OPG-1L EMCORE | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 4
Technical content
Features
50 MHz to 2.3 GHz Optimized for IF- and L-Band Video Signals Supports 30 km Links Optically-Isolated DFB Lasers Enable High- Dynamic-Range Links 25 dB Tx and Rx Adjustable Gain Range Peak Optimizer for Quick and Easy Set-Up SmartGain for Enhanced AGC Performance 50 & 75 Ohm BNC or 50 Ohm SMA Blind Mate RF Coax to Support Rear Plug-in Access SC/APC and LC/APC Optical Connectors Tx & Rx RF Power Monitors Via LED, SMA, Dashboard and SNMP Dashboard and SNMP Monitoring and Control LNB Power Capable Tx and Rx PCBA Card and Module 2 RU, 20-Slot openGear® Enclosure CE & CSA Certified, RoHS Block Diagram The OPG-1L was designed to be fully compatible with the openGear® standard for terminal equip- ment or cable headend design. This means that when you install an openGear® enclosure, you can then purchase additional insert cards from different manufacturers to be used in the same enclosure. The standard enclosure is a 19” rack-mount frame that can hold up to 20 insert cards. A separate module handles the management and control systems, and allows for local or remote interfaces. Each enclosure utilizes 2 RU of rack space, maximizing the overall usage of the equipment rack. The OPG-1L’s Rear Interface Modules may be pre-installed with its cabling, with- out corresponding PCBA cards. This allows the user to anticipate future expansion needs without significantly increasing the intial investment, and without having to access the rear panel and cabling once installed. The user simply purchases corre- sponding PCBA cards on an as-needed basis then slides them into place from the front of the frame, effortlessly locking them into the Rear Interface Module. System Design EMCORE’s openGear® OPG-1L RF Fiber Optic Links are optimized to perform in the 50 MHz to 2.3 GHz frequency range providing transparent signal transport for satellite antenna applications on an open architecture platform. The OPG-1L transmitter and receiver modules may be housed in the same chassis as EMCORE’S openGear® HD video, audio, serial data and USB extension / distribution cards, allowing full monitoring and control of each module via the DashBoard Network Management System (NMS). For higher optics, please contact us Transmitter Receiver Sin Push Button Sout PL PR Smon SmonOptimizer DC to LNB Photodiode Laser
satcom-sales@emcore.com www.emcore.com Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice. © 2013 EMCORE Corporation | REV 2013.10 +1 626-293-3400 DATASHEET | OCTOBER 2013 Performance Highlights Parameter Value Units TX Wavelength 1310, 1550 nm Optical Output Power 5 + 2 dBmo IF-Band Frequency L-Band Frequency 50-1000 850-2300 MHz MHz Frequency Response Any 500 MHz Full Band (50-2300 MHz) + 0.75 + 1.5 dB dB Input Return Loss (minimum) 10 dB Total Front-End RF Gain1 (at minimum attenuation setting) 25 + 2 dB Attenuation Adjustment Range 30 dB Spurs Free Dynamic Range2 98 dB-Hz2/3 Noise Figure (at maximum gain, 25°C) 23 dB Input IP3 (at maximum gain, 25°C) -4 dBm Total RF Power Into Laser 2 + 2dB dBm RX Output Return Loss (Minimum) 10 dB Total Front-End RF Gain1 (at minimum attentuation setting) 20 (dual output) 25 (single output) dB Attenuation Adjustment Range 15 dB Output IP3 (at maximum gain, 25°C) 20 (dual output) 25 (single output) dBm Parameter Value1 Units PCBA Card Dimension 12.8 L x 3.0 H x 0.681 W 32.5 L x 7.62 H x 0.173W in cm Rear Interface Module Dimension 1.362 L x 3.365 H x 1.31 W 3.46 L x 8.55 H x 3.33 W in cm Mechanical Characteristics Parameter Value Units TX Power Requirement 12 W Input Voltage (@ 1 A Max) 12 +/- 0.5 VDC LNB Voltage (at RF input port, 350 mA max) 17 +/- 1.0 VDC DC Current (@ +12 V with LNB Off) 350 +/- 50 mA RX Input Voltage (@ 1 A Max) 12 +/- 0.5 VDC DC Current (@ +12 V) 250 +/- 50 mA
Electrical Characteristics
PCBA Cards with Rear Interface Modules PCBA Cards 1. Defined per openGear Development Guide by Ross: 8200DR-001-02, 8200DR-001-03 1. Link RF Gain dB = TG + RG - 2*Fiber Loss dBo 2. SFDR = 2/3*(IIP3 + 174 - NF). Frame Options OPG-8321 OG3-FR openGear® OPG-1L 50 MHz – 2.3 GHz RF Fiber Optic Link
satcom-sales@emcore.com www.emcore.com Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice. © 2013 EMCORE Corporation | REV 2013.10 +1 626-293-3400 DATASHEET | OCTOBER 2013 Card Compatibility to openGear® Frames openGear® OPG-1L 50 MHz – 2.3 GHz RF Fiber Optic Link
satcom-sales@emcore.com www.emcore.com Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice. © 2013 EMCORE Corporation | REV 2013.10 +1 626-293-3400 DATASHEET | OCTOBER 2013 Transmitter/Receiver OPG-WX When ordering replace “W” with one of the RF Connector Options When ordering replace “X” with one of the RF Connector Impedance Options RF Connector Options “W” RF Connector Impedance Options (ohm) “X” B = BNC, S = SMA 5 = 50, 7 = 75 (BNC only) Ordering Information for Rear Interface Module (RIM) Ordering Information PCBA Card Transmitter1 Receiver OPG-UT-YY05-ZZ OPG-UR-V-ZZ Note 1. When installing transmitter cards in the OG3-FR frame, remove the pre-installed LNB blocker plug from the PCBA card but leave as-is for the OPG-8321 frame to prevent the frame’s DC-power alarm from activating. When ordering replace “U” with one of the Frequency Band Options When ordering replace “V” with one of the RX Only: RF Interface Options When ordering replace “YY” with one of the Wavelength Options** When ordering replace “ZZ” with one of the Optical Connector Options Frequency Band Options “U” Frequency Band (MHz) RX Only: RF Interface Options “V” Wavelength Options (nm) “YY” Output Power (dBmo) Optical Connector Options “ZZ” I = IF-Band 50-1000 1 = Output+Monitor 2 = Dual Outputs 13 = 1310, 55 = 1550 05 = +5 LA = LC-APC, SA = SC-APC (OG3-FR only) L = L-Band 850-2300 1 = Output+Monitor 2 = Dual Outputs 13 = 1310, 55 = 1550 05 = +5 LA = LC-APC, SA = SC-APC (OG3-FR only) Laser Safety This product meets the appropriate standard in Title 21 of the Code of Federal Regulations (CFR). FDA/CDRH Class 1M laser product. This device has been classified with the FDA/CDRH under accession number 0220191. All versions of this laser are Class 1M laser product, tested according to IEC 60825-1:2007 / EN 60825-1:2007. An additional warning for Class 1M laser products. For diverging beams, this warning shall state that viewing the laser output with certain optical instruments (for example: eye loupes, magnifiers, and microscopes) within a distance of 100 mm may pose an eye hazard. For collimated beams, this warning shall state that viewing the laser output with certain instruments designed for use at a distance (for example: telescopes and binoculars) may pose an eye hazard. Wavelength = 1.3/1.5 μm. Maximum power = 30 mW. *Caution - Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. *IEC is a registered trademark of the International Electrotechnical Commision. openGear® OPG-1L 50 MHz – 2.3 GHz RF Fiber Optic Link