OP4014B RFM | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 E-mail: info@rfm.com Page 1 of 2 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 http://www.rfm.com ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. OP4014B-041003
Electrical Characteristics
1, 9 627.329 MHz Tune Range ±25 ppm Tune Voltage VDC Tuning Linearity 1, 8 ±3% Tuning Sensitivity df/dv 2, 10 140 300 ppm/V Modulation Bandwidth 125 265 kHz Q and Q Output Voltage into 50 Ω (VSWR≤1.2) VO 1,3 0.60 1.1 VP-P Operating Load VSWR 1,3 2:1 Symmetry 3, 4, 5 Harmonic Spurious 3, 4, 6 -30 dBc Nonharmonic Spurious 3, 4, 6, 7 -60 dBc Phase Noise dBc/Hz@100Hz offset -70 dBc/Hz 1kHz offset -100 dBc/Hz 10k offset -120 Noise Floor -150 Q and Q Jitter RMS Jitter 3, 4, 6, 7 PSP-P No Noise on VCC 3, 4, 6, 7 PSP-P 200 mVP-P from 1MHz to ½ fO on PSP-P Input Impedence (Tuning Port) KΩ Output DC Resistance (between Q & Q) 1, 3 KΩ DC Power Supply Operating Voltage VCC 1, 3 3.13 3.3, 5.0 5.25 VDC Operating Current ICC 1, 3 mA Operating Case Temperature TC 1, 3 -40°C +85°C Lid Symbolization (YY=Year, WW=Week) RFM OP4014B YYWW SMC-08 Quartz SAW Stabilized and Filtered “Diff Sine” Technology Fundamental-Mode Oscillation at 627.329 MHz Voltage Tunable for Phase Lock Loop Operations Optical Timing Reference for G.709 Timing Applications The output of this device is generated and filtered by narrowband quartz SAW elements at 627.329 MHz. The configuration of this clock is intended to provide a pure signal for optical timing applications in noisy signal environments. The Q/Qbar differential output swing of ±1 volt about 0 vdc has symmetry better than ±1% into loads from 40 ohms to 70 ohms; determined by customer application. The long term frequency accuracy is set by an external reference source allowing this device to complete a Phase Lock Loop design without the usual noise and jitter problems associated with PLL’s. Absolute Maximum Ratings Rating Value Units DC Suppy Voltage 0 to 5.5 VDC Tune Voltage 0 to 6 VDC Case Temperature -55 to 100
627.329 MHz
CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. COCOM CAUTION: Approval by the U.S. Department of Commerce is required prior to export of this device. Notes: Unless otherwise noted, all specifications include any combination of load VSWR, Vcc, and temperature, with Q and Q terminated into 50 ohm loads to ground (see typical test circuit). Useful tuning range is in excess of what is required over temp, aging, pushing, pulling & accuracy. The design, manufacturing process, and specifications of this device are subject to change without notice. Only under the nominal conditions of 50 Ω load impedance with VSWR ≤ 1.2 and nominal power supply voltage. Symmetry is defined as the pulse width (in percent of total period) measured at the 50% points of Q or Q (see timing definitions). Jitter and other spurious outputs induced by externally generated electrical noise on VCC or mechanical vibration are not included in this specification, except where noted. External voltage regulation and careful PCB layout are recommended for optimum performance. Applies to period jitter of Q and Q. Measurements are made with the Tektronix CSA803 signal analyzer with at least 1000 samples. Linearity is a function of the percentage variation from a permitted linear deviation versus the amount of frequency tune range (see lin- earity definition). One or more of the following United States patents apply: 4,616,197; 4,670,681; 4,760,352. BLOCK DIAGRAM Q VCC Buffer Amplifier SAW Oscillator Vtune Q
627.329 MHz Optical Timing Clock
RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 E-mail: info@rfm.com Page 2 of 2 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 http://www.rfm.com ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. OP4014B-041003 SMC-8 8-Terminal Surface Mount Case Dimen- sion mm Inches MIN MAX MIN MAX A 13.46 13.97 0.530 0.550 B 9.14 9.66 0.360 0.380 C
1.93 Nominal
0.076 Nominal
D
3.56 Nominal
0.141 Nominal
E
2.24 Nominal
0.088 Nominal
F
1.27 Nominal
0.050 Nominal
G
2.54 Nominal
0.100 Nominal
H
3.05 Nominal
0.120 Nominal
J K
5.54 Nominal
0.218 Nominal
L
4.32 Nominal
0.170 Nominal
M
4.83 Nominal
0.190 Nominal
N
0.50 Nominal
0.020 Nominal
A B N J L (X2) D (X8) K (X8) C H G M (X3) E F Terminal Number Connection VCC Ground Enable/Disable Q Output Q Output Ground TUNE Input LID Ground TOP VIEW ELECTRICAL CONNECTIONS