OP4006B1 RFM | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 2

Technical content

RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 E-mail: info@rfm.com Page 1 of 2 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 http://www.rfm.com ©2001 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. OP4006B1-041003

  • Quartz SAW Stabilized Differential Output Technology
  • Very Low Jitter Fundamental-Mode Operation at 666.51 MHz
  • Voltage Tunable for Phase Locked Loop Applications
  • Optical Timing Reference for Forward Error Correction Applications The OP4006B1 is a voltage-controlled SAW clock (VCSC) designed for phase-locked loop (PLL) applications in optical data communications systems. The differential outputs of the OP4006B1 are generated by high-Q, fundamental mode quartz surface acoustic wave (SAW) technology. This technique provides very low output jitter and phase noise, plus excellent immunity to power supply noise. The OP4006B1 differential outputs fea- ture ±1% symmetry, and can be DC-configured to drive a wide range of high-speed logic families. The OP4006B1 is packaged in a hermetic metal-ceramic LCC. Absolute Maximum Ratings Rating Value Units DC Suppy Voltage 0 to 5.5 Vdc Tune Voltage 0 to 5.5 Vdc Case Temperature -55 to 100 °C

666.51 MHz

CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. COCOM CAUTION: Approval by the U.S. Department of Com merce is required prior to export of this device. Notes: 1. Unless otherwise noted, all specifications include the combined effects of load VSWR, V CC and T C . 2. Net tuning range after tuning out the effects of initial manufacturing tolerances, VSWR pushing/pulling, V CC , T C and aging. 3. The internal design, manufacturing processes, and specifications of this device are subject to change without notice. 4. Specified only for a balanced load with a VSWR < 1.2 ( 50 ohms each side), and a V CC = 3.0 Vdc. 5. Symmetry is defined as the width in (% of total period) measure at 50% of the peak-to-peak voltage of either output. 6. Jitter and other noise outputs due to power supply noise or mechanical vibration are not included in this specification excep t where noted. 7. Applies to period jitter of either differential output. Measured with a Tektronix CSA803 signal analyzer with at least 1000 s amples. 8. See Figure 4. 9. One or more of the following United States patents apply: 4, 616,197; 4,670,681; 4,760,352. Characteristic Sym Notes Minimum Typical Maximum Units Operating Frequency Absolute Frequency fO 1 666.51 MHz Tuning Range 2 ±100 ppm Tuning Voltage 1 0 3.3 Vdc Tuning Linearity 1, 8 ±5 % Modulation Bandwidth 50 kHz Q and Q Output Voltage into 50 Ω (VSWR ≤ 1.2) V O 1,3 0.60 1.1 V P-P Operating Load VSWR 1,3 2:1 Symmetry 3, 4, 5 49 51 % Harmonic Spurious 3, 4, 6 -15 dBc Nonharmonic Spurious 3, 4, 6, 7 -60 dBc Phase Noise @ 100 Hz offset 3, 6 -70 dBc/Hz @ 1 kHz offset 3, 6 -100 dBc/Hz @ 10 kHz offset 3, 6 -125 dBc/Hz Noise Floor 3, 6 -150 dBc/Hz Q and Q Jitter RMS Jitter 3, 4, 6, 7 1 ps No Noise on V CC 3, 4, 6, 7 12 ps P-P 200 mV P-P Noise, from 1 MHz to ½ f O on V CC 3 12 ps P-P Output DC Resistance (between Q & Q ) 1, 3 50 K Ω DC Power Supply Operating Voltage V CC 1, 3 3.13 3.3 or 5.0 5.25 Vdc Operating Current ICC 1, 3 70 mA Operating Case Temperature T C 1, 3 -40°C +85°C °C Lid Symbolization (YY=Year, WW=Week) RFM OP4006B1 YYWW SMC-08A

Electrical Characteristics

666.51 MHz Optical Timing Clock

RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 E-mail: info@rfm.com Page 2 of 2 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 http://www.rfm.com ©2001 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. OP4006B1-041003 SMC-8A 8-Terminal Surface Mount Case Dimension mm Inches MIN MAX MIN MAX A 13.46 13.97 0.530 0.550 B 9.14 9.66 0.360 0.380 C 1.93 Nominal 0.076 Nominal D 1.93 Nominal 0.076 Nominal E 2.54 Nominal 0.100 Nominal F 1.27 Nominal 0.050 Nominal Terminal Number Connection

1 Tune

2 *Enable

3 Ground

4 Ground

5 Q Output

6 Q Output

7 V CC

8 Ground

D E FA B C 0.190 X 0.088 CENTERED Typical Printed Circuit Board Land Pattern A typical land pattern for a circuit board is shown below. Ground- ing of the metallic center pad is optional. Typically 0.01" to 0.05" or 0.25 mm to 1.25 mm (8 Places) (The optimum value of this dimension is dependent on the PCB assembly process employed.) Dimensions *Enable Sense: Pin 2 Ground-Clock Off