OP4 VOXPOWER | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 1
Technical content
OUTPUT MODULE 4: 18V-58V, 3.75A, 150W OP4 DATASHEET All specifications are believed to be correct at time of publishing. Vox Power Ltd reserves the right to make changes to any of its products and to change or improve any part of the specification, electrical or mechanical design or manufacturing process without notice. Vox Power Ltd does not assume any liability arising out of the use or application of any of its products and o f any information to the maximum extent permitted by law. No license, express or implied, by estoppel or otherwise, to any intellec tual property rights is granted by this document or by any products of Vox Power Ltd. VOX POWER LTD DISCLAIMS ALL WARRANTIES AND REPRESENTATIONS OF ANY KIND WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF SUITABILITY, FITNESS FOR PURPOSE, MERCHANTABILITY AND NONINFRINGEMENT. Please consult your local distributor or Vox Power directly to ensure that you have the latest revision before using the prod uct and refer to the latest relevant user manual for further information rel ating to the use of the product. Vox Power Ltd products are not intended for use in connection with life support systems, human implantations, nuclear facilities or systems, aircraft, spacecraft, military or naval missile, ground support or control equipment used for the purpose of guidance navigation or direction of any aircraft, spacecraft or military or naval missile or any o ther application where product failure could lead to loss of life or catastrophic property damage. The user will hold Vox Power Ltd harmless from any loss, cost or damage resulting from its breach of these provisions. DOC-DTS-014-01, NEVO+ series output 4 datasheet Vox Power Limited | Unit 2, Red Cow Interchange Estate, Ballymount, Dublin 22, D22 Y8H2, Ireland | T +353 1 4591161 | www.vox-power.com OUTPUT 4 SPECIFICATIONS Parameter Details Min Typ Max Units Output voltage range See table 18 48 58 V Rated current 3.75 A Average output power 150 Watts Peak output power See graph, < 5 seconds 50% duty cycle
225 Watts
Initial voltage accuracy Factory set units -0.5 0.5 % Manual Voltage Adjust 11 turn potentiometer 3.6 V/turn Load Regulation Measured at sense terminals -300 300 mV Line Regulation Measured at sense terminals -0.1 0.1 %Vnom Cross Regulation Measured at sense terminals -0.2 0.2 %Vnom Minimum Load 0 Watts Temperature coefficient -0.02 0.02 %/°C Ripple and Noise 20MHz BW, pk-pk 1 %Vnom Transient response 25% to 75% load transient at 0.25A/uS 3 V Recovery to within 10% of Vset 100 uS Turn on rise time Monotonic 10% to 90% 1.5 3.5 mS Turn on overshoot 0.1 %Vset Turn on delay AC to PG 600 750 mS En to PG 15 20 mS Current share accuracy 5 %Imax Open sense offset Open sense, voltage offset due to bias currents 2 %Vnom Holdup voltage 50 V Isolation to ground Each terminal 250 V Over current protection % of rated current 105 125 %rated Reverse current protection % of rated current -6 0 %rated Short circuit protection (Hiccup mode) Period 125 mS Duty cycle 3 % Voltage threshold (Measured at sense terminals) 3.5 V Over voltage protection Latching 66 V Over Temperature protection Internally monitored. Latching 115 125 °C Sense cable protection Positive -3 3 V Negative 2 V Power Good threshold Low threshold only 90 %Vset Current output signal ISIG=0.6+IOUT/(IRTD*1.25) 0 110 %Irated Current limit control ILMT = (VCTRL-0.6)*IRTD*1.25 0 110 %Irated Remote voltage control VOUT=VSET((1.8-VCTRL)/0.6) 0 300 %Vset Bias supply 10mA max 4.5 5 5.2 V Reliability 40°C 80% load 1 FPMH Warranty 2 Years Wire Size 20 18 10 AWG Weight 60 Grams Size 60mm x 35mm x 17mm Notes: All specifications are believed to be correct at time of publication and are subject to change without notice.