DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 6

Technical content

Series NP01 Subminiature Smooth Actuation Pushbuttons D74 IndicatorsAccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons DIlluminated PBSlides Programmable RockersTouch Tilt Toggles www.nkkswitches.com Electrical Capacity (Resistive Load) Logic Level: 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Other Ratings Contact Resistance: 50 milliohms maximum Insulation Resistance: 500 megohms minimum @ 250V DC Dielectric Strength: 250V AC minimum between contacts for 1 minute minimum Mechanical Life: 500,000 operations minimum Electrical Life: 500,000 operations minimum Nominal Operating Force: Standard: 1.5N ±0.5 Newtons High: 2.5N ±0.8 Newtons Stroke: 1.5mm (.059”) Materials & Finishes Actuator: Silicon rubber Case: Polycarbonate resin Base: Glass fiber reinforced polyamide resin Movable Contact: Silver over nickel with gold plating Stationary Contacts: Brass with gold plating Switch Terminals: Brass with gold plating Environmental Data Operating Temperature Range: –25°C through +50°C (–13°F through +122°F) for Illuminated –25°C through +70°C (–13°F through +158°F) for Nonilluminated Humidity: 90 ~ 95% humidity for 96 hours @ 40°C (104°F) Vibration: 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours Shock: 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Installation Cap Installation Force: 5.0N maximum downward force on actuator PCB Processing Soldering: Wave Soldering: 270°C maximum @ 6 seconds maximum Manual Soldering: 390°C maximum @ 4 seconds maximum Cleaning: These devices are not process sealed. Hand clean locally using alcohol based solution. Standards & Certifications The NP01 Series pushbuttons have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current, logic-level circuit. When used as intended in a logic-level circuit, the results do not produce hazardous energy. General Specifications 7/19/17

Series NP01Subminiature Smooth Actuation Pushbuttons D75 IndicatorsAccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons D Illuminated PBSlides Programmable TogglesRockersTouch Tilt www.nkkswitches.com Actual Size Distinctive Characteristics Soft touch actuation achieved by mechanical silicon rubber structure. Distinct, long stroke of 1.5mm (.059”). Entire cap is fully illuminated with single or bicolor LED. Compact design with dimension of 12.5mm (.492”) from PC board to top of cap. Alternating legend options with bicolor LED. Available in both high (2.5N) or standard (1.5N) operating force. Gold plated contacts provide high reliability. Crimped terminals ensure secure PC mounting and prevent dislodging during soldering. Molded-in terminals prevent entry of flux, solvents, and other contaminants.

Series NP01 Subminiature Smooth Actuation Pushbuttons D76 IndicatorsAccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons DIlluminated PBSlides Programmable RockersTouch Tilt Toggles www.nkkswitches.com TYPICAL SWITCH ORDERING EXAMPLE H Contacts & Terminals G03 Gold Contacts and PC Terminals, Rated 0.4VA @ 28V AC/DC Packaging No Code Partitioned Tray, Any Quantity (With or without caps installed) S Stick-Tube

50 Pieces/Stick

(For switch body only; caps pack- aged separately) FNP01 LEDs Cap Types & Colors JFG0315 Single or Bicolor LED C Red D Amber F Green CF Bicolor Red/Green DG Bicolor Amber/Blue Cap Lens/Diffuser Colors JB Clear/White (Combine with any LED) JC Clear/Red JD Clear/Amber JF Clear/Green Nonilluminated N No LED Solid Color Cap A Black B White C Red H Gray Bicolor LED CF Red/Green DG Amber/Blue L Illumination L Illuminated N Nonilluminated Pole & Circuit

15 SPST OFF (ON)

( ) = Momentary Normally Open Contacts Operating Force A Standard (1.5N) (Black Switch Body) H High (2.5N) (Gray Switch Body) Bicolor Alternating Legend Caps JCF Red/Green JDG Amber/Blue Alternating Legends

11 ON (pos) OFF (pos)

12 ON (neg) OFF (neg)

13 START STOP

14 OPEN CLOSE

Contact factory for custom options. Part Numbers for Alternating Legends Color Part Number Red/Green AT3023JCF11 ~ AT3023JCF14 Amber/Blue AT3023JDG11 ~ AT3023JDG14 Refer to Ordering Table for Alternating Legend that corresponds with last 2 digits of part number. High (2.5N) Operating Force SPST OFF-Momentary ON Circuit Normally Open Contacts DESCRIPTION FOR TYPICAL ORDERING EXAMPLE NP0115HG03LF-JF Green LED Clear Lens with Green Diffuser Gold Contacts with 0.4VA Rating Straight PC Terminals

Series NP01Subminiature Smooth Actuation Pushbuttons D77 IndicatorsAccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons D Illuminated PBSlides Programmable TogglesRockersTouch Tilt www.nkkswitches.com A Standard Nominal Operating Force 1.5 ±0.5N Switch base is Black Gold Contacts Straight PC Terminals 0.4VA maximum @ 28V AC/DC maximumG03 High Nominal Operating Force 2.5 ±0.8N Switch base is Gray H Nonilluminated Models Plunger Position ( ) = Momentary Connected Terminals Throw & Switch Schematic Pole Model Normal Down Note: Switch is marked with LC1, 1, L3, L4, L1, L2, 2, LC2. SP NP0115AG03N NP0115HG03N OFF (ON) Normally Open 1-2 SPST Illuminated Models Plunger Position ( ) = Momentary Connected Terminals Throw & Switch Schematic Pole Model Normal Down SP NP0115AG03L NP0115HG03L OFF (ON) Normally Open 1-2 SPST (+) (-) Notes: Switch is marked with LC1, 1, L3, L4, L1, L2, 2, LC2. Lamp circuit is isolated and requires an external power source. L Illuminated NonilluminatedN POLE & CIRCUIT OPERATING FORCE CONTACTS, TERMINALS, & RATING ILLUMINATION

Series NP01 Subminiature Smooth Actuation Pushbuttons D78 IndicatorsAccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons DIlluminated PBSlides Programmable RockersTouch Tilt Toggles www.nkkswitches.com R = E – VF IF Where: R E VF IF = Resistor Value (Ohms) = Source Voltage (V) = Forward Voltage (V) = Forward Current (A) VF I FR + E Anode Cathode LEDs are an integral part of the switch and not available separately. The electrical specifications shown are determined at a basic temperature of 25°C. If the source voltage exceeds the forward voltage, a ballast resistor is required. Specifications in parentheses ( ) below for Bicolor LED denote simultaneous illumination of Red and Green. LED COLORS & SPECIFICATIONS Amber LED Red or Green LEDs Red/Green Bicolor LED LC2 (+) L4 (-) L3 (-) LC1 (+) L2 (-) L1 (-) LC2 (+) L4 (-) Green L3 (-) Red LC1 (+) L2 (-) Red L1 (-) Green LC1 (+) L2 (-) L1 (-) Color ATTENTION ELECTROSTATIC SENSITIVE DEVICES Single Color LED Bicolor LED Red Amber Green Red Green Amber Blue Maximum Forward Current IFM 30mA 30mA 25mA 30 (25)mA 25 (25)mA 30mA 30mA Typical Forward Current IF 20mA 20mA 16mA 20 (20)mA 16 (5)mA 20mA 20mA Maximum Reverse Voltage VRM 5V 5V 5V 5V 5V 5V 5V Current Reduction Rate ∆IF 0.41mA/°C above 25°C 0.38mA/°C above 25°C 0.33mA/°C above 25°C 0.40mA/°C above 25°C 0.33mA/°C above 25°C 0.40mA/°C above 25°C 0.40mA/°C above 25°C Ambient Temperature Range –25° ~ +50°C –25° ~ +50°C C D F CF DG LC2 (+) L4 (-) Blue L3 (-) Amber LC1 (+) L2 (-) Amber L1 (-) Blue Amber/Blue Bicolor LED JB Cap for Single or Bicolor LED JC JD JF Clear Lens/White Diffuser Clear Lens/Red Diffuser Clear Lens/Amber Diffuser Clear Lens/Green Diffuser Alternating Legend Cap for Bicolor LED Material: Polycarbonate Resin Standard Alternating Legend Pairs AT3022 12mm Square Cap Material: Polycarbonate Resin AT3023 12mm Square Cap Clear Lens Alternating Legend Filter CAP TYPES & COLORS (10.2) .402 (12.0) Sq .472 (10.2) .402 (12.0) Sq .472 11 12 13 Cap illumination is alternating Green/Red or Blue/Amber; legend text is black. Contact factory for other Alternating Legends. Legend illustrations are approximate representations of the actual characters on the filters. ON OFF ON OFF START STOP 14 OPEN CLOSE Green/Red or Blue/Amber Green/Red or Blue/Amber Green/Red or Blue/Amber Green/Red or Blue/Amber JCF Red/Green Amber/BlueJDG

Series NP01Subminiature Smooth Actuation Pushbuttons D79 IndicatorsAccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons D Illuminated PBSlides Programmable TogglesRockersTouch Tilt www.nkkswitches.com Illuminated • Straight PC NP0115HG03LF-JF S Stick-Tube Packaging 50 pieces per stick Switches must be ordered in 50-piece increments when stick-tube packaging is selected. This packaging is for the switch body only. Caps will be packaged separately. Partitioned Tray Any quantity. No code is required. Switches may be packaged with or without caps installed. No Code 1. NP01 Pushbuttons are electrostatically sensitive. To prevent damage to LED, devices must be properly isolated from static electricity. 2. Once the cap is installed onto the switch body, it cannot be removed. 3. When assembling cap, align projection on switch body to slot on inside of cap. (Refer to illustration at right.) 4. * Legends may be printed on the lens with laser etch, screen print or pad print methods. Epoxy based ink is recommended. 5. Do not use excessive force during installation on PC board or for cap installation. * NKK Switches can provide custom legends for caps. Contact factory for more information. A Solid Color Cap for Nonilluminated B C H Black White Red Gray Material: Polycarbonate Resin AT3024 12mm Square Cap ATTENTION ELECTROSTATIC SENSITIVE DEVICES CAP TYPES & COLORS (CONTINUED) TYPICAL SWITCH DIMENSIONS PACKAGING PRECAUTIONS FOR HANDLING & STORAGE (10.2) .402 (12.0) Sq .472 (12.0) .472 Sq (12.5) .492 (10.2) .402 (0.3) .012 Typ (7.0) .276 (3.3) .130 (2.1) .083 LC22L2L1 LC1 1L 3L 4 (2.0) .079 Typ (0.5) .020 Typ (2.0) .079 Typ (7.0) .276 (1.0) .039 Dia Typ CL LC11L3L4 L1L22LC2 (15.3) .602 (11.85) .467 (470.0) 18.504 Projection Slot LEGEND ORIENTATION LC22L2L1 LC1 1L 3L 4 LC2 OPEN Orient cap with legend as shown here, and “LC2” at lower right of switch body. Orders for switches with legends will be assembled as illustrated. Top View Bottom View