MX0141VA0 IDT | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 6
Technical content
1:4 High-Speed / Low-Speed Multiplexer Pair MX0141VA0 Short-Form Datasheet © 2017 Integrated Device Technology, Inc. 1 May 1, 2017
Description
Important: All parameters in this short-form datasheet are prior to device characterization and are currently subject to change. Final parameters will be updated after device characterization. The MX0141VA0 is comprised of a high -speed, 1:4 multiplexer (mux) path and a low-speed, 1:4 mux path. The high-speed path is a bidirectional 12-bit port 1:4 mux. The low- speed path is a unidirectional 4 -bit port 1:4 mux. Both high-speed and low-speed paths support SSTL_12 and SSTL_18 signaling. Both paths are controlled in an identical manner using the input control signals: SEL1, SEL0, and EN_B. For example, when EN_B is asserted LOW, one of the high-speed [ABCD] ports is connected to IN while all the remaining ports are tri-stated. When input EN_B is HIGH all four [ABCD] ports are tri-stated. Figure 1. Block Diagram Table 1. Characteristics of HS and LS Paths
Table 2. Pin Descriptions [a] The voltages on these pins must always be equal to or lower than the voltage on VDD. This also applies during device power up sequencing.
The absolute maximum ratings are stress ratings only. Stresses greater than those listed below can cause permanent damage to the device. Table 3. Absolute Maximum Ratings
- Recommended Operating Conditions
Table 4. Recommended Operating Conditions
4.1 Control Logic – High-Speed Ports
Table 5. The IN, A, B, C, and D ports are bidirectional. “Z” indicates tri-state and all bits follow the IOL_HS specification. Table 5. Control of High-Speed Ports
4.2 Control Logic – Low-Speed Ports
the internal pull-up side set to the FUNC input pin voltage. INL is a unidirectional signal multiplexed to the selected LA, LB, LC, or LD port. Table 6. Control of Low-Speed Ports
0 XX 1 Z Z Z Z
1 XX 1 H H H H
MX0141VA0 Short-Form Datasheet © 2017 Integrated Device Technology, Inc. 5 May 1, 2017
4.3 FUNC Pin Description
The FUNC pin is used to choose either the “Z” tri-state or a weak pull-up for the low-speed outputs when deselected. Example 1: The FUNC pin is set to less than 0.3V. In this example, deselected low-speed outputs will be “Z” = tri-state. Example 2: The FUNC pin is set to greater than 0.9V .In this example, deselected low-speed mux outputs will be pulled to the FUNC voltage level through individual internal pull -up resistors of value R _LS. For example, if FUNC is set to 1.8V, then deselected low-speed mux outputs will be pulled up to 1.8V through individual internal pull-up resistors of the value R_LS. Example 3: The FUNC pin is set to a voltage between 0.3V and 0.9V. In this example, the FUNC input is set to an illegal voltage level and the FUNC pin functionality is undetermined. 5. Package Drawings 98-FCCSP package information is available on the IDT website at www.idt.com/package/AVG98. 6. Marking Diagram The following package marking diagram is for illustration purposes only. Line 1 – IDTMX0141 Line 2 – VA0AVG Line 3 – #YYWW$ where # is the step; YYWW is the last two digits of the year followed by two digits for the workweek; and $ is the assembly location Line 4 – Lot number 7. Ordering Information Orderable Part Number Description and Package MSL Rating Shipping Packaging Temperature MX0141VA0AVG MX0141VA0, 4.0 x 7.5 mm 98-FCCSP (AVG98)
3 Tray 0° to +85°C
MX0141VA0AVG8 MX0141VA0, 4.0 x 7.5 mm 98-FCCSP (AVG98)
3 Tape and Reel 0° to +85°C
MX0141VA0 Short-Form Datasheet © 2017 Integrated Device Technology, Inc. 6 May 1, 2017 8. Revision History Revision Date Description of Change May 1, 2017 Implementation of the following edit corresponding to edit in full MX0141VA0 Datasheet approved revision dated April 19, 2017: Deletion of note regarding availability being limited to samples in section 7. April 6, 2017 Initial release of short-form datasheet. Corporate Headquarters
6024 Silver Creek Valley Road
San Jose, CA 95138 www.IDT.com Sales 1-800-345-7015 or 408-284-8200 Fax: 408-284-2775 www.IDT.com/go/sales Tech Support www.IDT.com/go/support DISCLAIMER Integrated Device Technology, Inc. (IDT) and its affiliated companies (herein referred to as “IDT”) reserve the right to modify the products and/or specifications described herein at any time, without notice, at IDT's sole discretion. Performance specifications and operating parameters of the described products are d etermined in an independent state and are not guaranteed to perform the same way when installed in customer products. The information contained herein is provided without representation or warranty of a ny kind, whether express or implied, including, but not limited to, the suitability of IDT's products for any particular purpose, an implied warranty of merchantability, or non -infringement of the intellectual property rights of others. This document is presented only as a guide and does not convey any license under intellectual property rights of IDT o r any third parties. IDT's products are not intended for use in applications involving extreme environmental conditions or in life support systems or similar devices where the failure or malfunction of an IDT product can be reasonably expected to signific antly affect the health or safety of users. Anyone using an IDT product in such a manner does so at their own risk, absent an express, written agreement by IDT. Integrated Device Technology, IDT and the IDT logo are trademarks or registered trademarks of IDT and its subsidiaries in the United States and other countries. Other trademarks used herein are the property of IDT or their respective third party owners. Fo r datasheet type definitions and a glossary of common terms, visit www.idt.com/go/glossary . All contents of this document are copyright of Integrated Device Technology, Inc. All rights reserved.