MT5150-UG MARKTECH | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 6

Technical content

3Northway Lane North Latham,New York 12110. Tollfree:1.800.984.5337 Phone:1.518.956.2980 Fax:1.518.785.4725 Http://www.marktechopto.com SPECIFICATION P ART NO. : MT5150-UG 5.0mm ROUND LED LAMP OBSERVE PRECAUTION FOR HANDLING ELECTRO STATIC SENSITIVE DEVICES ATTENTION

MT5150-UG 5.0 mm ROUND LED LAMP VER.: 01 Date: 2007/03/22 Page: 1/5

Description

This true green lamp is made with InGaN/Sapphire chip and water clear epoxy resin. 8.724.0 MIN. 1.5 TYP. 0.5 MAX. A K 5.9 Notes: 1. All dimensions are in mm. 2. Tolerance isÔ0.25mm unless otherwise noted. Part No. Material Emitting Color Lens Color MT5150-UG InGaN/Sapphire True green Water clear

MT5150-UG 5.0 mm ROUND LED LAMP VER.: 01 Date: 2007/03/22 Page: 2/5 Absolute Maximum Ratings at Ta=25Ċ Parameter Symbol Rating Unit Power Dissipation PD 100 mW Reverse V oltage VR 5 V D.C. Forward Current If 25 mA Reverse (Leakage) Current Ir 50 DŽA Peak Current(1/10Duty Cycle,0.1ms Pulse Width.) If(Peak) 100 mA Operating Temperature Range Topr. -40 to +95 Ċ Storage Temperature Range Tstg. -40 to +100 Ċ Soldering Temperature(1.6mm from body) Tsol. Dip Soldering : 260 for Ċ 5 sec. Hand Soldering : 350 for 3 sec.Ċ Electrostatic discharge ESD. 6000 V Electrical and Optical Characteristics: Parameter Symbol Condition Min. Typ. Max. Unit Luminous Intensity IV If=20mA 12000 22000 mcd Forward V oltage Vf If=20mA 3.2 4.0 V Dominant Wavelength λd If=20mA 520 525 535 nm Reverse (Leakage) Current Ir Vr=5V 50 µA Viewing Angle 2ǀ1/2 If=20mA 15 deg Spectrum Line Halfwidth ∆λ If=20mA 35 nm Notes: The datas tested by IS tester. 2. Customer’s special requirements are also welcome.

MT5150-UG 5.0 mm ROUND LED LAMP VER.: 01 Date: 2007/03/22 Page: 3/5 Typical Electrical / Optical Characteristics Curves : Applied Voltage (V) Forward Current IF(mA) FORWARD CURRENT VS.APPLIED VOLTAGE Forward Current (mA) FORWARD CURRENT VS. LUMINOUS INTENSITY Temperature ( )Ċ FORWARD CURRENT VS. AMBIENT TEMPERATURE 0 20 40 60 100 80 Forward Current IF(mA)10 3KQJO R j-a=480 Ċ/W RADIATION DIAGRAM 80° 90° 60° 70° 50° 30° 40° 0.10.5 0.7 0.8 0.3 1.0 0.9 0.40.2 0.6 0° 10° 20° 0.0 10.0 20.0 30.0 10000 20000 50000Relative Luminous Intensity(mcd) 30000 40000

MT5150-UG 5.0 mm ROUND LED LAMP VER.: 01 Date: 2007/03/22 Page: 4/5 Specifications for Bin Grading: Iv(mcd) BIN MIN. MAX. Z1 12000 16800 Z2 16800 23500 Z3 23500 32900 Specifications for Vf Group: Vf(V) Group MIN. MAX. V6 2.6 2.8 V7 2.8 3.0 V8 3.0 3.2 V9 3.2 3.4 V10 3.4 3.6 V11 3.6 3.8 V12 3.8 4.0 *Majority VF bins are highlighted in Yellow. Specifications for Wavelength Group: ǃD(nm) @20mA Group MIN . MAX. X7 520 525 X8 525 530 X9 530 535

MT5150-UG 5.0 mm ROUND LED LAMP VER.: 01 Date: 2007/03/22 Page: 5/5 Precautions: TAKE NOTE OF THE FOLLOWING IN USE OF LED 1. Temperature in use Since the light generated inside the LED needs to be emitted to outside efficiently, a resin with high light transparency is used; therefore, additives to improve the heat resistance or moisture resistance (silica gel , etc) which are used for semiconductor products such as transistors cannot be added to the resin. Consequently, the heat resistant ability of the resin used for LED is usually low; therefore, please be careful on the following during use. Avoid applying external force, stress, and excessive vibration to the resins and terminals at high temperature. The glass transition temperature of epoxy resin used for the LED is approximately 120-130 Ċ. At a temperature exceeding this limit, the co efficient of liner expansion of the resin doubles or more compared to that at nor mal temperature and the resin is softened. If external force or stress is applie d at that time, it may cause a wire rupture. 2. Soldering Please be careful on the following at soldering. After soldering, avoided applying external force, stress, and excessive vibration until the products go to cooling process (normal temperature), <Same for products with terminal leads> (1) Soldering measurements: Distance between melted solder side to bottom of resin shall be 1.6mm or longer. (2) Dip soldering : Pre-heat: 90Ċ max. (Backside of PCB), Within 60 seconds. S o l d e r b a t h : 2 6 0Ô5Ċ (Solder temperature), Within 5 seconds. (3) Hand soldering: 350 Ċ max. (Temperature of soldering iron tip), Within 3 seconds. 3. Insertion Pitch of the LED leads and pitch of mounting holes need to be same. 4. Others Since the heat resistant ability of the LED resin is low, SMD components are used on the same PCB, please mount the LED after adhesive baking process for SMD components. In case adhesive baking is done after LED lamp in sertion due to a production process reason, make sure not to apply external force, stress, and excessive vibration to the LED and follow the conditions below. Baking temperature: 120 Ċ max. Baking time: Within 60 seconds. If soldering is done sequentially after the adhesi ve baking, please perform the soldering after cooling down the LED to normal temperature.