MT093 ZARLINK | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 9
Technical content
Features
- Internal control latches and address decoder
- Short set-up and hold times
- Wide operating voltage: 4.5V to 14.5V
- 3.5Vpp analog signal capability ON Ω max. @ V DD =14V, 25 C R ON Ω @ V DD =14V, 25 C
- Full CMOS switch for low distortion
- Minimum feedthrough and crosstalk
- Low power consumption ISO-CMOS technology
Applications
- PBX systems
- Mobile radio
- Test equipment /instrumentation
- Analog/digital multiplexers
- Audio/Video switching
Description
The Zarlink MT093 is fabricated in Zarlink’s ISO- CMOS technology providing low power dissipation and high reliability. The device contains a 8x12 array of crosspoint switches along with a 7 to 96 line decoder and latch circuits. Any one of the 96 switches can be addressed by selecting the appropriate seven input bits. The selected switch can be turned on or off by applying a logical one or zero to the DATA input.
Ordering Information
MT093AE 40 Pin Plastic DIP MT093AP 44 Pin PLCC to 70 C Figure 1 - Functional Block Diagram 7 to 96 Decoder Latches 8 x 12 Switch Array STROBE DATA RESET VDD VSS Xi I/O (i=0-11) Yi I/O (i=0-7) 9696 AX0 AX1 AY0 AY1 AY2 AX2 AX3 ISSUE 2 March 1997 MT093 8 x 12 Analog Switch Array ISO-CMOS
Figure 2 - Pin Connections Pin Description Pin # Name Description PDIP PLCC 11Y 3 Y3 Analog (Input/Output): this is connected to the Y3 column of the switch array.
22 A Y 2
Y2 Address Line (Input) 3 3 RESET Master RESET (Input): this is used to turn off all switches. Active High. 4,5 4,5 AX3,AX0 X3 and X0 Address Lines (Inputs) 6,7 6-8 NC No Connection. 8-13 9-14 X6-X11 X6-X11 Analog (Inputs/Outputs): these are connected to the X6-X11 rows of the switch array. 14 15-17 NC No Connection. 15 18 Y7 Y7 Analog (Input/Output): this is connected to the Y7 column of the switch array. 16 - NC No Connection. 17 19 Y6 Y6 Analog (Input/Output): this is connected to the Y6 column of the switch array. 18 20 STROBE STROBE (Input) : enables function selected by address and data. Address must be stable before STROBE goes high and DATA must be stable on the falling edge of the STROBE. Active High. 19 21 Y5 Y5 Analog (Input/Output): this is connected to the Y5 column of the switch array. 20 22 V SS Ground Reference. 21 23 Y4 Y4 Analog (Input/Output): this is connected to the Y4 column of the switch array. 22, 23 24,25 AX1,AX2 X1 and X2 Address Lines (Inputs) 24, 25 26,27 AY0,AY1 Y0 and Y1 Address Lines (Inputs) 26, 27 28-31 NC No Connection. 28 - 33 32-37 X5-X0 X5-X0 Analog (Inputs/Outputs): these are connected to the X5-X0 rows of the switch array. 34 38,39 NC No Connection. 35 40 Y0 Y0 Analog (Input/Output) : this is connected to the Y0 column of the switch array. 36 - NC No Connection. 37 41 Y1 Y1 Analog (Input/Output) : this is connected to the Y1 column of the switch array.
40 PIN PLASTIC DIP 44 PIN PLCC
2318 19 20 21 22 24 25 26 27 28 17 29 NC NC NC NC NC DATA VDD AY2 RESET AX3 AX0 NC
The MT093 is an analog switch matrix with an array size of 8 x 12. The switch array is arranged such that there are 8 columns by 12 rows. The columns are referred to as the Y input/output lines and the rows are the X input/output lines. The crosspoint analog switch array will interconnect any X line with any Y line when turned on and provide a high degree of isolation when turned off. The control memory consists of a 96 bit write only RAM in which the bits are selected by the address input lines (AY0-AY2, AX0-AX3). Data is presented to the memory on the DATA input line. Data is asynchronously written into memory whenever the STROBE input is high and is latched on the falling edge of STROBE. A logical “1” written into a memory cell turns the corresponding crosspoint switch on and a logical “0” turns the crosspoint off. Only the crosspoint switches corresponding to the addressed memory location are altered when data is written into memory. The remaining switches retain their previous states. Any combination of X and Y lines can be interconnected by establishing appropriate patterns in the control memory. A logical “1” on the RESET input line will asynchronously return all memory locations to logical “0” turning off all crosspoint switches. Address Decode The seven address lines along with the STROBE input are logically ANDed to form an enable signal for the resettable transparent latches. The DATA input is buffered and is used as the input to all latches. To write to a location, RESET must be low while the address and data lines are set up. Then the STROBE input is set high and then low causing the data to be latched. The data can be changed while STROBE is high, however, the corresponding switch will turn on and off in accordance with the data. Data must be stable on the falling edge of STROBE in order for correct data to be written to the latch. 38 42 DATA DATA (Input) : a logic high input will turn on the selected switch and a logic low will turn off the selected switch. Active High. 39 43 Y2 Y2 Analog (Input/Output) : this is connected to the Y2 column of the switch array. 40 44 V DD Positive Power Supply. Pin Description Pin # Name Description PDIP PLCC
- Exceeding these values may cause permanent damage. Functional operation under these conditions is not implied. † DC Electrical Characteristics are over recommended temperature range & recommended power supply voltages. ‡ Typical figures are at 25 C and are for design aid only; not guaranteed and not subject to production testing. Absolute Maximum Ratings - Voltages are with respect to V SS unless otherwise stated. Parameter Symbol Min Max Units
1 Supply Voltage V
V SS -0.3 -0.3 16.0 V DD +0.3 V V
2 Analog Input Voltage V
-0.3 V DD +0.3 V
3 Digital Input Voltage V
V SS -0.3 V DD +0.3 V
4 Current on any I/O Pin I
5 Storage Temperature T
S -65 +150 C
6 Package Power Dissipation PLASTIC DIP P
D 0.6 W Recommended Operating Conditions - Voltages are with respect to V SS unless otherwise stated. Characteristics Sym Min Typ Max Units Test Conditions
1 Operating Temperature T
O 02 5 7 0 C
2 Supply Voltage V
4.5 14.5 V
3 Analog Input Voltage V
V SS 3.5 V
4 Digital Input Voltage V
V SS V DD V Voltages are with respect to V SS =0V, V DD =14V unless otherwise stated. Characteristics Sym Min Typ Max Units Test Conditions
1 Quiescent Supply Current I
µ A All digital inputs at V IN SS or V DD 7 15 mA All digital inputs at V IN =2.4V
2 Off-state Leakage Current I
µ AI V Xi - V Yj I = V DD - V SS
3 Input Logic “0” level V
0.8 V
4 Input Logic “1” level V
2.4 V
5 Input Leakage (digital pins) I
µ A All digital inputs at V IN = V SS or V DD - VIDC/VODC is the external DC offset applied at the analog I/O pins. Characteristics Sym 25 °C6 0 °C7 0 °C Units Test Conditions Typ Max Typ Max Typ Max
1 On-state V DD=14V
RON 45 65 75 Ω VSS=0V, IVXi-VYjI = 0.25V VIDC=6.75V VODC=6.5V
2 Difference in on-state
ON 51 0 1 0 1 0 Ω VDD=14V, VSS=0, VIDC=6.75V VODC=6.5V IVXi-VYjI = 0.25V
† Timing is over recommended temperature range. ‡ Typical figures are at 25 °C and are for design aid only; not guaranteed and not subject to production testing. Crosstalk measurements are for Plastic DIPS only, crosstalk values for PLCC packages are approximately 5dB better. † Timing is over recommended temperature range. Digital Input rise time (tr) and fall time (tf) = 10ns. ‡ Typical figures are at 25 °C and are for design aid only; not guaranteed and not subject to production testing. I/O pins. Voltages are with respect to VDD=7V, VDC=0V, VSS=-7V, unless otherwise stated. Characteristics Sym Min Typ ‡ Max Units Test Conditions
1 Switch I/O Capacitance C S 20 pF f=1 MHz
2 Feedthrough Capacitance C F 0.2 pF f=1 MHz
3 Frequency Response
Channel “ON” 20LOG(V OUT/VXi)=-3dB F3dB 45 MHz Switch is “ON”; V INA = 2Vpp sinewave; RL = 1kΩ 4 Total Harmonic Distortion THD 0.05 % Switch is “ON”; V INA = 2Vpp sinewave f= 1kHz; RL=1kΩ
5 Feedthrough
Channel “OFF” Feed.=20LOG (V OUT/VXi) FDT -95 dB All Switches “OFF”; V INA= 2Vpp sinewave f= 1kHz; R L= 1kΩ.
6 Crosstalk between any two
channels for switches Xi-Yi and Xj-Yj. Xtalk=20LOG (V Yj/VXi). Xtalk -45 dB V INA=2Vpp sinewave f= 10MHz; RL = 75Ω. -90 dB V INA=2Vpp sinewave f= 10kHz; RL = 600Ω. -85 dB V INA=2Vpp sinewave f= 10kHz; RL = 1kΩ. -80 dB V INA=2Vpp sinewave f= 1kHz; RL = 10kΩ.
7 Propagation delay through
tPS 50 ns R L=1kΩ; CL=50pF I/O pins. Voltages are with respect to VDD=7V, VDC=0V, VSS=-7V, unless otherwise stated. Characteristics Sym Min Typ ‡ Max Units Test Conditions
1 Control Input crosstalk to switch
(for DATA, STROBE, Address) CXtalk 50 mVpp V IN=3V+VDC squarewave; RIN=1kΩ, RL=10kΩ.
2 Digital Input Capacitance C DI 10 pF f=1MHz
3 Switching Frequency F O 10 MHz
4 Setup Time DATA to STROBE t DS 20 ns R L= 1kΩ, CL=50pF
5 Hold Time DATA to STROBE t DH 20 ns R L= 1kΩ, CL=50pF
6 Setup Time Address to STROBE t AS 20 ns R L= 1kΩ, CL=50pF
7 Hold Time Address to STROBE t AH 20 ns R L= 1kΩ, CL=50pF
8 STROBE Pulse Width t SPW 40 ns R L= 1kΩ, CL=50pF
9 RESET Pulse Width t RPW 80 ns R L= 1kΩ, CL=50pF
10 STROBE to Switch Status Delay t S 80 200 ns R L= 1kΩ, CL=50pF
11 DATA to Switch Status Delay t D 100 200 ns R L= 1kΩ, CL=50pF
12 RESET to Switch Status Delay t R 70 200 ns R L= 1kΩ, CL=50pF
Table 1. Address Decode Truth Table ➀ This address has no effect on device status.
www.zarlink.com Information relating to products and services furnished herein by Zarlink Semiconductor Inc. or its subsidiaries (collectively “Zarlink”) is believed to be reliable. However, Zarlink assumes no liability for errors that may appear in this publication, or for liability otherwise arising from t he application or use of any such information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, u nder patents or other intellectual property rights owned by Zarlink or licensed from third parties by Zarlink, whatsoever. Purchasers of products are also hereby notified that the use of product in certain ways or in combination with Zarlink, or non-Zarlink furnished goods or services may infringe patents or other intellectual property rights owned by Zarlink. This publication is issued to provide information only and (unless agreed by Zarlink in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other information appearing in this publication are subject to change by Zarlink without notice. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user’s responsibility t o fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to Zarlink’s conditions of sale which are available on request. Purchase of Zarlink’s I2C components conveys a licence under the Philips I 2C Patent rights to use these components in and I 2C System, provided that the system conforms to the I2C Standard Specification as defined by Philips. Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc. Copyright Zarlink Semiconductor Inc. All Rights Reserved. TECHNICAL DOCUMENTATION - NOT FOR RESALE For more information about all Zarlink products visit our Web Site at