MSP100 TEC | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 8

Technical content

SENSOR SOLUTIONS ///MSP100 Page 1 08/2016

FEATURES

 Single Piece Construction; No Welds, No Oil  100% Stainless Steel Isolation for Harsh Chemical Measurement  Low Cost  14-Bit Digital Output or Analog

APPLICATIONS

 Beverage Dispensing Systems  Water Pressure or Flow Monitor  Medical Equipment  Industrial Equipment/Hydraulics  Tank Level Measurement  Manifold Pressure MSP100 Pressure Transducer SPECIFICATIONS  Analog and 14-Bit Digital Output  Small Size  Low Cost  316L Stainless Steel or 17-4PH The MSP100 pressure transducer provides stainless steel media compatibility in a low cost, small profile solution. This sensor has no silicone gel or polymeric media isolation methods to fail in contact with water or other harsh chemicals. Pressure connections are provided via an o-ring seal. The device is available in both analog and 14-bit digital output with a port material of either 316L SS or 17-4PH. Additional custom port options available to meet your application needs. The small size vs. performance and media compatibility are provided through solid-state technology. STANDARD RANGES Range psig 0 to 100  0 to 150  0 to 250  0 to 500 

SENSOR SOLUTIONS ///MSP100 08/2016 Page 2 PERFORMANCE SPECIFICATIONS (ANALOG, OUTPUT SIGNAL “2”) Ambient Temperature: 25°C (unless otherwise specified) PARAMETERS MIN TYP MAX UNITS NOTES Supply Voltage 4.75 5.00 5.25 Vdc Zero Offset -2 2 mV Ratiometric Span 98 100 102 mV Ratiometric Current Consumption 2 mA Proof Pressure 1.5X Rated Burst Pressure 3X Rated Endurance 1E+6 0~FS Cycles Accuracy -0.5 ±0.2 0.5 %Span RSS of BFSL: Linearity, Hysteresis, Repeatability Long Term Stability 0.25 %Span Minimum Resistance between Transducer and Body

50 MΩ @250Vdc

Thermal Zero Shift -2.0 2.0 %Span Reference to 25°C over Compensated Temperature Thermal Span Shift -2.0 2.0 %Span Reference to 25°C over Compensated Temperature Compensation Temperature 0 45 °C Operating Temperature 0 55 °C Response Time (10% to 90%) 0.1 mS Vibration ±20g MIL-STD-810C, Procedure 514.2, Figure 514.2-2, Curve L Shock 50g, 11 msec half sine shock per mil standard 202F. Method 213B, Condition A For custom configurations, consult factory.

SENSOR SOLUTIONS ///MSP100 08/2016 Page 3 PERFORMANCE SPECIFICATIONS (DIGITAL, OUTPUT SIGNAL “J” OR “S”) Ambient Temperature: 25°C (unless otherwise specified) PARAMETERS MIN TYP MAX UNITS NOTES Supply Voltage 2.7 5.0 Vdc Output at Zero Pressure 720 1000 1280 Count Output at FS Pressure 14,720 15,000 15,280 Count Current Consumption 3 mA Proof Pressure 1.5X Rated Burst Pressure 3X Rated Endurance 1E+6 0~FS Cycles Accuracy -0.5 0.5 %Span RSS of BFSL: Linearity, Hysteresis, Repeatability A/D Resolution 14 Bit Operating Temperature 0 55 °C @250Vdc Operating Temperature Output 512 1075 Count Temperature Accuracy -3 3 °C Pressure Port Temperature Thermal Zero Shift -2.0 2.0 %F.S. Reference to 25°C over Compensated Temperature Thermal Span Shift -2.0 2.0 %F.S. Reference to 25°C over Compensated Temperature Compensated Temperature 0 45 °C Response Time (10% to 90%) 3 mS @ 4MHz Without Sleep Mode Response Time (10% to 90%) 8.4 mS @ 4MHz With Sleep Mode Vibration ±20g MIL-STD-810C, Procedure 514.2, Figure 514.2-2, Curve L Shock 50g, 11 msec half sine shock per mil standard 202F. Method 213B, Condition A For custom configurations, consult factory.

SENSOR SOLUTIONS ///MSP100 08/2016 Page 4 DIMENSIONS

SENSOR SOLUTIONS ///MSP100 08/2016 Page 5 WIRING Analog mV Output Wiring Connection PIN 1 PIN 2 PIN 3 PIN 4 Molex 4pin Connector +SUPPLY +OUTPUT -OUTPUT -SUPPLY PCB Mount Digital I2C Output Wiring Connection PIN 1 PIN 2 PIN 3 PIN 4 Molex 4pin Connector VDD GND SDA SCL PCB Mount Digital SPI Output Wiring Connection PIN 1 PIN 2 PIN 3 PIN 4 PIN5 Molex 5pin Connector VDD GND SDA SCLK SS PCB Mount

SENSOR SOLUTIONS ///MSP100 08/2016 Page 6 SENSOR OUTPUT

SENSOR SOLUTIONS ///MSP100 08/2016 Page 7 TEMPERATURE OUTPUT

SENSOR SOLUTIONS ///MSP100 08/2016 Page 8 OUTPUT SIGNAL Code Output Signal Supply Voltage (V) 2 0 – 100mV 5 ± 0.25 J I2C 2.7 – 5.0 S SPI 2.7 – 5.0

ORDERING INFORMATION

MS1 J 1 - 0 00 0 0 J - 100P G Model Output Signal Connection Type - Port Material 00 Sleep Mode (Digital Only) Address for I2C (Digital Only) Port Type - Pressure Range Pressure Type MS1 2 = 0 - 100mV J = I2C S = SPI 1 = Cable 2 ft with Molex Connector 0 = 316L SS 1 = 17-4PH 0 = Without Sleep Mode 1 = With Sleep Mode (If Analog, use “0”) 0 = 0x28H 1 = 0x36H 2 = 0x46H 3 = 0x48H 4 = 0x51H (If Analog or SPI, use “0”) J = O-Ring Face Seal U = O-Ring Radial Seal 100P 150P 250P 500P G = Gauge NORTH AMERICA EUROPE ASIA Measurement Specialties, Inc., a TE Connectivity company

45738 Northport Loop West

Fremont, CA 94538 Tel: +1 800 767 1888 Fax: +1 510 498 1578 customercare.frmt@te.com MEAS France SAS, a TE Connectivity company

4 Rue Gaye Marie

31027 Toulouse, France

Tel: +33 (5) 822 822 00 Fax: +33 (5) 820 821 51 customercare.tlse@te.com Measurement Specialties (China) Ltd., a TE Connectivity company No. 26 Langshan Road Shenzhen High-Tech Park (North) Nanshan District, Shenzhen, 518057 China Tel: +86 755 3330 5088 Fax: +86 755 3330 5099 customercare.shzn@te.com TE.com/sensorsolutions Measurement Specialties, Inc., a TE Connectivity company. Measurement Specialties, TE Connectivity, TE Connectivity (logo) and EVERY CONNECTION COUNTS are trademarks. All other logos, products and/or company names referred to herein might be trademarks of their respective owners. The information given herein, including drawings, illustrations and schematics which are intended for illustration purposes only, is believe d to be reliable. However, TE Connectivity makes no warranties as to its accuracy or completeness and disclaims any liability in connection with its use. TE Connectivity‘s obligation s shall only be as set forth in TE Connectivity‘s Standard Terms and Conditions of Sale for this product and in no case will TE Connectivity be liable for any incidental, indirect or consequential damages arising out of the sale, resale, use or misuse of the product. Users of TE Connectivity products should make their own evaluation to determine the suitability of each such product for the specific application. © 2015 TE Connectivity Ltd. family of companies All Rights Reserved.