MSK4226 ANAREN | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 6
Technical content
75 VOLT 20 AMP MOSFET
The MSK4226 is a complete H-Bridge circuit to be used for DC brushed motor control or Class D switchmode amplifi - cation. All of the drive/control circuitry for the lowside and highside switches are internal to the circuit. Logic level inputs are provided for controlling each MOSFET independently, allowing every possible switch combination except those that would cause a simultaneous conduction or shoot-through condition for each half bridge. This gives the user freedom to use various modulation schemes for PWM control. The MSK4226 is constructed in a space efficient plastic power package that can be directly bolted to a heatsink. DESCRIPTION: PIN-OUT INFORMATION 8548-151 Rev. G 4/151 FEATURES:
- Low RDS(ON) 0.013Ω Typical
- Non-Hermetic Low Cost Complete H-Bridge
- 20 Amp Capability, 75 Volt Maximum Rating
- Self-contained Smart Lowside/Highside Drive Circuitry
- Shoot-through Protection
- Isolated Case Allows Direct Heatsinking
- Logic Level Disable Input
- Individual Logic Level Gate Drive Inputs for Various Modulation Schemes NC VCC BHI DIS BLI AHI ALI GND GND NC RSENSE B RSENSE B OUTPUT B OUTPUT B OUTPUT A OUTPUT A RSENSE A RSENSE A MIL-PRF-38534 AND 38535 CERTIFIED FACILITY EQUIVALENT SCHEMATIC TYPICAL APPLICATIONS
RDS (ON) 1 4 VDS(ON) Voltage Instantaneous Forward Voltage Reverse Recovery Time 1 Leakage Current VCC SUPPLY CHARACTERISTICS Quiescent Bias Current VCC Voltage Range 1 LOGIC CONTROL INPUTS,ALI,BLI,AHI,BHI and DIS 1 Input Voltage LO Input Voltage HI Input Current (VIN=0V) SWITCHING CHARACTERISTICS 1 Rise Time Fall Time Dead Time Each MOSFET ID=20A Each MOSFET ID=20A 3 Each MOSFET IS=20A Intrinsic Diode 3 Intrinsic Diode Each MOSFET V+=70V RL=100Ω VCC IOUT IPK VOUT θJC ABSOLUTE MAXIMUM RATINGS Parameter ELECTRICAL SPECIFICATIONS Units Ω V V nS uA mA V V V uA nS nS nS Max. 0.013 0.52 1.3 280 250 0.8 270 MSK4226 Typ. 0.45 1.0 Min. 2.7 Test Conditions 2 TST TLD TC TJ NOTES: Guaranteed by design but not tested. Typical parameters are representative of actual device performance but are for reference only. VCC=+12V, V+=28V, RSENSE A,B=Ground, DIS=0V unless otherwise specified. Measured using a 300µS pulse with a 2% Duty Cycle. On Resistance is specified for the Internal MOSFET for Thermal Calculations. It does not include the package pin resistance. Continuous operation at or above absolute maximum ratings may adversely effect the device performance and/or life cycle. When applying power to the device, apply the low voltage followed by the high voltage or alternatively, apply both at the same time. Do not apply high voltage without low voltage present. Tc= +25°C Unless Otherwise Specified High Voltage Supply Logic Supply Continuous Output Current Peak Output Current Output Voltage Range Thermal Resistance (Output Switches @ 125°C) 75V 16V 20A 40A GND -2V min. to V + max. 3.0°C/W Storage Temperature Range Lead Temperature Range (10 Seconds) Case Operating Temperature MSK4226 Junction Temperature -55°C to +125°C 300°C -40°C to +85°C +150°C 8548-151 Rev. G 4/15
VCC - Is the low voltage supply for powering internal logic and drivers for the lowside and highside MOSFETS. The supplies for the highside drivers are derived from this voltage. OUTPUT B - Is the output pin for the B half bridge. OUTPUT A - Is the output pin for the A half bridge. RSENSE A - Is the connection for the bottom of the A half bridge. This can have a sense resistor connection to the V+ return ground for current limit sensing, or can be connected directly to ground. The maximum voltage on this pin is ±2 volts with respect to GND. RSENSE B - Is the connection for the bottom of the B half bridge. This can have a sense resistor connection to the V+ return ground for current limit sensing, or can be connected directly to ground. The maximum voltage on this pin is ±2 volts with respect to GND. GND - Is the return connection for the input logic and VCC. DIS - Is the connection for disabling all 4 output switches. DIS - ABLE high overrides all other inputs. When taken low, everything functions normally. An internal pullup to VCC will keep DISABLE high if left unconnected. This is a diagram of a typical application of the MSK4226. The design VCC voltage is +12 volts and should have a good low ESR bypass capacitor such as a tantalum electrolytic. The digital inputs can come from a microprocessor or any type of PWM controller. The controller will use the current sense signal to either control current through PWM, current limit the bridge, or both. Current sensing is done in this case by a 0.01 ohm sense resistor to sense current from both legs of the bridge separately. It is important to make the high current traces as big as possible to keep inductance down. The storage capacitor connected to the V+ and the module should be large enough to provide the high energy pulse without the voltage sagging too far. A low ESR ceramic capacitor or large polypropylene capacitor will be required. Mount the capacitor as close to the module as possible. The connection between GND and the V+ return should not be carrying any motor current. The sense resistor signal is com - mon mode filtered as necessary to feed the limiting circuitry for the microprocessor. This application will allow full four quadrant torque control for a closed loop servo system. Any modulation scheme may be used, however, but the current sensing scheme may have to change. A snubber network is usually required, due to the inductance in the power loop. It is important to design the snubber network to suppress any positive spikes above 70V and negative spikes below -2V with respect to ground. *There are certain inductive load situations that can possibly cause a momentary shoot-through or cross-conduction condition in the MSK4226. This shoot-through is approximately 100nSec long and can be several amps, depending on the layout and impedence of the bypassing circuit. Most bypassing and current sensing filtering will usually eliminate the effects. However, in the case where it is still present, or the sense resistor trace lengths are long, reverse-biased ultra-fast recovery diodes or power schottky diodes from RSENSE A and RSENSE B to power ground will minimize or eliminate the situation. V+ - Is the higher voltage H-bridge supply. The MOSFETS obtain the drive current from this supply pin. The voltage on this pin is limited by the drive IC. The MOSFETS are rated at 75 volts. Proper by-passing to GND with sufficient capacitance to suppress any voltage transients, and to ensure removing any drooping during switching, should be done as close to the pins of the module as possible. MSK4226 PIN DESCRIPTIONS TYPICAL SYSTEM OPERATION ALI - Is the logic level digital input for controlling the lowside MOSFET in the A half bridge. If AHI is driven high or not connected externally then ALI controls both the lowside and highside MOS- FETs, with dead time in between. This is due to the simultaneous conduction lockout feature. DIS will override the ALI input. AHI - Is the logic level digital input for controlling the highside MOSFET in the A half bridge. ALI high level input will override this input to prevent simultaneous conduction. DIS will override the AHI input. BLI - Is the logic level digital input for controlling the lowside MOSFET in the B half bridge. If BHI is driven high or not con - nected externally then BLI controls both the lowside and highside MOSFETs, with dead time in between. This is due to the simulta- neous conduction lockout feature. DIS will override the BLI input. BHI - Is the logic level digital input for controlling the highside MOSFET in the B half bridge. BLI high level input will override this input to prevent simultaneous conduction. DIS will override the BHI input. 8548-151 Rev. G 4/15
MSK4226 EVALUATION SCHEMATIC 4 8548-151 Rev. G 4/15
ORDERING INFORMATION
CAUTION: THIS IS A NON-HERMETIC DEVICE. DO NOT EXPOSE PLASTIC HOUSING TO LIQUID 8548-151 Rev. G 4/15 MOUNTING TORQUE: 3-4 INCH POUNDS ESD TRIANGLE INDICATES PIN 1 WEIGHT=36.6 GRAMS TYPICAL ALL DIMENSIONS ARE SPECIFIED IN INCHES
The information contained herein is believed to be accurate at the time of printing. MSK reserves the right to make changes to its products or specifications without notice, however, and assumes no liability for the use of its products. Please visit our website for the most recent revision of this datasheet. MSK www.anaren.com/msk 6 8548-151 Rev. G 4/15