MSK3554 ANAREN | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 6
Technical content
FEATURES: Stable at Low Gain Fast Slew Rate - 1200V/µs Typical Gain Bandwidth Product - 1200 MHz Typical Low Quiescent Current - ±14.0 mA Typical Low Offset - 2 mV Maximum Drop In Replacement for OPA 3554 and TP 3554 High Output Current - ±100mA Minimum Contact MSK for MIL-PRF-38534 Qualification Status DESCRIPTION: The MSK3554 is a pin compatible, low gain stable, drop-in replacement for the OPA 3554 and TP 3554. The MSK3554 does not exhibit high frequency output oscillations like other versions of the 3554 when operated at closed loop gains of less than 55 V/V. The extremely low input bias current and input offset voltage ratings coupled with a high slew rate and wide bandwidth make the MSK3554 an excellent choice for fast D/A converters, buffers, pulse amplifiers and other high speed op-amp applications. The MSK3554 is packaged in an 8-pin TO-3 using thick film hybrid technology to obtain high reliability and compact size. Fast D/A Converters Pulse Amplifiers Video Instrumentation Fast Buffer/Follower Video Frequency Filters Balance 2 Negative Power Supply Non-Inverting Input Inverting Input Output Positive Power Supply Compensation Balance 1 TYPICAL APPLICATIONS PIN-OUT INFORMATION HIGH SPEED, WIDEBAND OPERATIONAL AMPLIFIER EQUIVALENT SCHEMATIC MIL-PRF-38534 AND 38535 CERTIFIED FACILITY 8548-155 Rev. E 10/151
±18V ±150mA ±25V -55°C to +125°C -40°C to +85°C STATIC Supply Voltage Range Quiescent Current Thermal Resistance INPUT Input Offset Voltage Input Offset Voltage Drift Input Offset Adjust Input Bias Current Input Offset Current Input Impedance Power Supply Rejection Ratio Input Noise Density Input Noise Voltage OUTPUT Output Voltage Swing Output Current Settling Time Power Bandwidth Bandwidth (Small Signal) TRANSFER CHARACTERISTICS Slew Rate Open Loop Voltage Gain ABSOLUTE MAXIMUM RATINGS TST TLD PD TJ Storage Temperature Range Lead Temperature Range (10 Seconds) Power Dissipation Junction Temperature Supply Voltage Peak Output Current Differential Input Voltage Case Operating Temperature MSK3554B MSK3554 -65°C to +150°C 300°C See Curve 175°C Unless otherwise specified ±VCC=±15VDC AV=-1, measured in false summing junction circuit. Devices shall be capable of meeting the parameter, but need not be tested. Typical parameters are for reference only. Industrial grade devices shall be tested to subgroups 1 and 4 unless otherwise specified. Military grade devices ('B' suffix) shall be 100% tested to subgroups 1,2,3 and 4. Subgroup 5 and 6 testing available upon request. Subgroup 1,4 TA=TC=+25°C Subgroup 2,5 TA=TC=+125°C Subgroup 3,6 TA=TC=-55°C Measurement taken .5 second after application of power using automatic test equipment. Continuous operation at or above absolute maximum ratings may adversely effect the device performance and/or life cycle. NOTES: ±VCC IOUT VIN TC Min. ±12 ±10.5 ±100 800 Max. ±18 ±20 ±30 ±2.0 ±50 ±50 ±50 ±25 ±30 150 Min. ±12 ±10 ±100 750 Max. ±18 ±20 ±3.0 ±100 ±30 150 Units V mA mA °C/W mV µV/°C mV pA nA pA nA Ω dB nV√Hz µVrms V mA nS MHz MHz V/µS dB MSK3554B 11 11 MSK3554 Adjust to Zero Adjust to Zero ELECTRICAL SPECIFICATIONS Typ. ±15 ±14 ±0.5 ±20 ±10 ±10 ±2.0 ±2.0 110 10.0 ±12 ±120 120 1200 Typ. ±15 ±14 ±0.5 ±20 ±20 ±2.0 110 10.0 ±12 ±120 120 1200 Test Conditions Group A Subgroup 2,3 2,3 1,2,3 2,3 2,3 VIN=0V AV=-1V/V Junction to Case Output Devices Bal.Pins=N/C VIN=0V AV=-10V/V VIN=0V RPOT=20KΩ To +VCC AV=-1V/V VCM=0V Either Input VCM=0V F=DC Differential ∆ VCC=10V F=1KHz F=10Hz To 1MHz RL=100Ω TJ<150°C 0.1% 10V step RL=100Ω VO=±10V CC=0 CC=0 VOUT=±10V RL=100Ω CC=0 CC=0 RL=100Ω F=1KHz VOUT=±10V Parameter 8548-155 Rev. E 10/15
Refer to the following thermal model and governing equations to determine appropriate heat sinking for your application. Example: This example demonstrates a worst case analysis for the op-amp output stage. This occurs when the output voltage is 1/2 the power supply voltage. Under this condition, maximum power transfer occurs and the output is under maximum stress. Conditions: VCC = ±16VDC VO = ±8Vp Sine Wave, Freq. = 1KHZ RL = 100Ω Governing Equation: TJ=PD x (RθJC + RθCS + RθSA) + TA Where TJ = Junction Temperature PD = Total Power Dissipation RθJC = Junction to Case Thermal Resistance RθCS = Case to Heat Sink Thermal Resistance RθSA = Heat Sink to Ambient Thermal Resistance TC = Case Temperature TA = Ambient Temperature TS = Sink Temperature For a worst case analysis we will treat the +8Vp sine wave as an 8 VDC output voltage. 1.) Find Driver Power Dissipation PD = (VCC-VO) (VO/RL) = .64W 2.) For conservative design, set TJ=+125°C 3.) For this example, worst case TA=+90°C 4.) RθJC = 37°C/W from MSK3554B Data Sheet 5.) RθCS = 0.15°C/W for most thermal greases 6.) Rearrange governing equation to solve for RθSA RθSA = ((TJ - TA)/PD) - (RθJC) - (RθCS) = 54.7 - 37.15 = 17.54°C/W The heat sink in this example must have a thermal resistance of no more than 17.54°C/W to maintain a junction temperature of no more than +125°C. OFFSET NULL Typically, the MSK3554(B) has an input offset voltage of less than ±0.5mV. If it is desirable to adjust the offset closer to "zero", or to a value other than "zero", the circuit below is recommended. Rp should be a ten-turn 20KΩ potentiometer. Typical offset adjust is ±20mV. Thermal Model: GAIN -10 -100 follower Rfb 5.6KΩ 5.6KΩ 10KΩ Cfb 2.0pF 1.2pF 0.0pF 0pF Ccomp 10pF 10pF 0.0pF 12pF Rin 5.6KΩ 560Ω 100Ω COMPONENT SELECTION TABLE COMPENSATION The compensation capacitor is connected between pins 1 and 3 and is used to optimize bandwidth and slew rate while maintaining circuit stability. The effect of compensation capacitance can be seen in the Bode Plot under the Typical Performance Curves. As closed loop gain increases, compensation capacitance can decrease and higher slew rates and wider bandwidths will be realized. See the component selection table for recommended values of input and feedback resistance as well as feedback capacitance and com - pensation capacitance. 3 8548-155 Rev. E 10/15
TYPICAL PERFORMANCE CURVES 4 8548-155 Rev. E 10/15
ORDERING INFORMATION
MSK3554B Mil-PRF-38534 Class H 8548-155 Rev. E 10/15 TOP VIEW PIN REFERENCES SHOWN. WEIGHT=14.1 GRAMS TYPICAL ALL DIMENSIONS ARE SPECIFIED IN INCHES
The information contained herein is believed to be accurate at the time of printing. MSK reserves the right to make changes to its products or specifications without notice, however, and assumes no liability for the use of its products. Please visit our website for the most recent revision of this datasheet. MSK www.anaren.com/msk 6 8548-155 Rev. E 10/15