MSJC78

SMCJ5.0 TSC | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 5

Technical content

Features

/cuspopen For surface mounted application /cuspopen Low profile package /cuspopen Built-in strain relief /cuspopen Glass passivated junction /cuspopen Excellent clamping capability /cuspopen Fast response time: Typically less than 1.0ps from 0 volt to B V m i n . /cuspopen Typical I R less than 1μA above 10V /cuspopen High temperature soldering guaranteed: 260OC / 10 seconds at terminals /cuspopen Plastic material used carries Underwriters Laboratory Flammability Classification 94V-0 /cuspopen 1500 watts peak pulse power capability with a 10 X 1000 us waveform by 0.01% duty cycle Mechanical Data /cuspopen Case: Molded plastic /cuspopen Terminals: Solder plated /cuspopen Polarity: Indicated by cathode band /cuspopen Standard packaging: 16mm tape (EIA STD RS-481) /cuspopen Weight: 0.21gram SMC/DO-214AB Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Type Number Symbol Value Units Peak Power Dissipation at TA=25 O C, Tp=1ms (Note 1) PPK Minimum 1500 Watts Steady State Power Dissipation Pd 5 Watts Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method) (Note 2, 3) - Unidirectional Only IFSM 200 Amps Maximum Instantaneous Forward Voltage at 100.0A for Unidirectional Only (Note 4) VF 3.5 / 5.0 Volts Operating and Storage Temperature Range TJ, TSTG -55 to + 150 OC Notes: 1. Non-repetitive Current Pulse Per Fig. 3 and Derated above TA=25OC Per Fig. 2. 2. Mounted on 0.6 x 0.6" (16 x 16mm) Copper Pads to Each Terminal. 3. 8.3ms Single Half Sine-wave or Equivalent Square Wave, Duty Cycle=4 Pulses Per Minute Maximum. 4. VF=3.5V on SMCJ5.0 thru SMCJ90 Devices and VF=5.0V on SMCJ100 thru SMCJ170 Devices. Devices for Bipolar Applications 1. For Bidrectional Use C or CA Suffix for Types SMCJ5.0 through Types SMCJ170. 2. Electrical Characteristics Apply in Both Directions.

• 607 - RATINGS AND CHARACTERISTIC CURVES (SMCJ SERIES) FIG.4- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PEAK FOR WARD SURGE CURRENT . (A) 1 10 100 100 200 NUMBER OF CYCLES AT 60Hz 8.3ms Single Half Sine Wave JEDEC Method UNIDIRECTIONAL ONLY FIG.1- PEAK PULSE POWER RATING CURVE Pppm, PEAK PULSE POWER, KW 0.1 100 td. PULSE WIDTH, sec. 0.1 s 1.0 s 10 s 100 s 1.0ms 10ms 0.31X0.31" (8.0X8.0mm) COPPER PAD AREAS NON-REPETITIVE PULSE WAVEFORM SHOWN in FIG. 3 T =25 C A 0 FIG.6- TYPICAL JUNCTION CAPACITANCE Cj, JUNCTION CAP ACITANCE, pF 1 10 400100 100 1000 10000 20000 VWM, REVERSE STAND-OFF VOLTAGE. (V) Tj=25 C f=1.0MHz Vsig=50mVp-p MEASURED AT ZERO BIAS VR MEASURED AT STAND-OFF VOLTAGE,V WM FIG.5- TYPICAL JUNCTION CAPACITANCE BIDIRECTIONAL Cj, JUNCTION CAP ACITANCE, pF 1 10 400100 100 1000 10000 VWM, REVERSE STAND-OFF VOLTAGE. (V) Tj=25 C f=1.0MHz Vsig=50mVp-p MEASURED AT ZERO BIAS MEASURED AT STAND-OFF VOLTAGE,V WM FIG.2- PULSE DERATING CURVE PEAK PULSE POWER (Pppm) or CURRENT (lpp) DERATING IN PERCENT AGE, % 0 25 50 75 100 125 150 175 200 100 200 TA, AMBIENT TEMPERATURE. C O FIG.3- PULSE WAVEFORM 0 1.0 2.0 3.0 4.0 150 100 t, TIME, ms lppm, PEAK PULSE CURRENT % IRSM tr=10 sec. 10/1000 sec. WAVEFORM AS DEFINED BY R.E.A. td PEAK VALUE lppm HALF VALUE- lpp PULSE WIDTH (td) is DEFINED AS THE POINT WHERE THE PEAK CURRENT DECAYS to 50% of lppm 150

• 608 - ELECTRICAL CHARACTERISTICS (TA=25OC unless otherwise noted) Breakdown Maximum Maximum Device Type Device Voltage Test Stand-off Reverse Peak Pulse Maximum Modified Marking V(BR) (Volts) Current voltage Leakage Surge Clamping "J" Bend Lead Code (Note 1) at IT(mA) VWM(Volts) at VWM Current IPPM Voltage at IPPM (MIN / MAX) (Note 3) I D(uA) (Note 2) (Amps) VC(Volts)

• 609 - ELECTRICAL CHARACTERISTICS (TA=25OC unless otherwise noted) Breakdown Maximum Maximum Device Type Device Voltage Test Stand-off Reverse Peak Pulse Maximum Modified Marking V(BR) (Volts) Current voltage Leakage Surge Clamping "J" Bend Lead Code (Note 1) at IT(mA) V WM(Volts) at VWM Current IPPM Voltage at IPPM (MIN / MAX) (Note 3) I D(uA) (Note 2) (Amps) VC(Volts) Notes: 1. V(BR) measured after IT applied for 300us, IT=Square wave pulse or equivalent. 2. Surge current waveform per Fig. 3 and derate per Figure 2. 3. For bidirectional types having VWM of 10 Volts and less, the ID limit is doubled 4. all terms and symbols are consistent with ANSI/IEEE C62.35