MPX2102_10 FREESCALE | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 16
Technical content
Features
- Temperature Compensated Over 0 °C to +85°C
- Easy-to-Use Chip Carrier Package Options
- Available in Absolute, Differential and Gauge Configurations
- Absolute, Differential and Gauge Options
ORDERING INFORMATION
No. # of Ports Pressure Type Device MarkingNone Single Dual Gauge Differential Absolute Unibody Package (MPX2102 Series) MPX2102A Tray 344 • • MPX2102A MPX2102AP Tray 344B • • MPX2102AP MPX2102ASX Tray 344F • • MPX2102A MPX2102DP Tray 344C • • MPX2102DP MPX2102GP Tray 344B • • MPX2102GP MPX2102GVP Tray 344D • • MPX2102GVP Small Outline Package (MPXV2102G Series) MPXV2102GP Tray 1369 • • MPXV2102GP MPXM2102A Rail 1320 • • MPXM2102A MPXM2102AT1 Tape and Reel 1320 • • MPXM2102A MPXM2102AS Rail 1320A • • MPXM2102AS MPXM2102AST1 Tape and Reel 1320A • • MPXM2102AS MPXM2102D Rail 1320 • • MPXM2102D MPXM2102DT1 Tape and Reel 1320 • • MPXM2102D MPXM2102GS Rail 1320A • • MPXM2102GS MPXM2102GST1 Tape and Reel 1320A • • MPXM2102GS MPX2102 0 to 100 kPa (0 to 14.5 psi) 40 mV Full Scale (Typical) Series Application Examples
- Pump/Motor Control
- Robotics
- Level Detectors
- Medical Diagnostics
- Pressure Switching
- Barometers
- Altimeters
2 Freescale Semiconductor
Table 1. Operating Characteristics (VS = 10 VDC, TA = 25°C unless otherwise noted, P1 > P2)
- 1.0 kPa (kiloPascal) equals 0.145 psi.
- Device is ratiometric within this spec ified excitation range. Operating the device above the specified excitation range may induce additional
error due to device self-heating.
- Full Scale Span (V FSS) is defined as the algebraic difference between the output voltage at full rated pressure and the output voltage at the
- Offset (V OFF) is defined as the output voltage at the minimum rated pressure.
- Accuracy (error budget) consists of the following:
- Linearity: Output deviation from a straight line relationshi p with pressure, using end point method, over the specified pressure range.
- Temperature Hysteresis:Output deviation at any temperature within the operating temperature range, after the temperature is cycled to and from the minimum or maximum operating temperature points, with zero differential pressure applied.
- Pressure Hysteresis: Output deviation at any pressure with the specified range, when this pressure is cycled to and from the minimum or maximum rated pressure at 25°C.
- TcSpan: Output deviation at full rated pressure over the temperature range of 0 to 85°C, relative to 25°C.
- TcOffset: Output deviation with minimum rat ed pressure applied, over the temperature range of 0 to 85°C, relative to 25°C. -0.6 -1.0 -0.6 -1.0 0.4 1.0 0.4 1.0 %VFSS %VFSS Pressure Hysteresis(5) (0 to 100 kPa) — — ±0.1 — %VFSS Temperature Hysteresis(5)(-40°C to +125°C) — — ±0.5 — %VFSS Temperature Coefficient of Full Scale Span(5) TCVFSS -2.0 — 2.0 %VFSS Temperature Coefficient of Offset(5) TCVOFF -1.0 — 1.0 mV Input Impedance ZIN 1000 — 2500 W Output Impedance ZOUT 1400 — 3000 W Response Time(6) (10% to 90%) 6. Response Time is defined as the time from the incremental change in the output to go from 10% to 90% of its final value when subjected to a specified step change in pressure. tR — 1.0 — ms Warm-Up Time — — 20 — ms Offset Stability(7) 7. Offset stability is the product’s output deviation when subjected to 1000 hours of Pulsed Pressure, Temperature Cycling with Bias Test. — — ±0.5 — %VFSS
4 Freescale Semiconductor
proportional to the differential pressure applied. is drawn on the pressure (P1) side. vacuum (P2) side relative to the pressure (P1) side. on the stand-alone pressure sensor chip. Figure 1. Temperature Compensated Pressure Sensor Schematic Table 2. Maximum Ratings
- Exposure beyond the specified limits may caus e permanent damage or degradation to the device.
6 Freescale Semiconductor
The Pressure (P1) side may be identified by using Table 3. Table 3. Pressure (P1) Side Delineation
1320 Stainless Steel Cap
7 Freescale Semiconductor
NOTES: DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. CONTROLLING DIMENSION: INCH. DIMENSION -A- IS INCLUSIVE OF THE MOLD STOP RING. MOLD STOP RING NOT TO EXCEED 16.00 (0.630). MAM0.136 (0.005) T 1234PIN 1 R N L G F D 4 PL SEATING PLANE -T- C M J B -A- DAMBAR TRIM ZONE: F THIS IS INCLUDED WITHIN DIM. "F" 8 PL 1 23 4 Y Z STYLE 1: PIN 1. GROUND 2. + OUTPUT 3. + SUPPL Y 4. - OUTPUT STYLE 2: PIN 1. V CC 2. - SUPPL Y 3. + SUPPL Y 4. GROUND STYLE 3: PIN 1. GND 2. -VOUT 3. VS 4. +VOUT DIM MIN MAX MIN MAX MILLIMETERSINCHES A 0.595 0.630 15.11 16.00 B 0.514 0.534 13.06 13.56 C 0.200 0.220 5.08 5.59 D 0.016 0.020 0.41 0.51 F 0.048 0.064 1.22 1.63 G 0.100 BSC 2.54 BSC J 0.014 0.016 0.36 0.40 L 0.695 0.725 17.65 18.42 M 30˚ NOM 30˚ NOM N 0.475 0.495 12.07 12.57 R 0.430 0.450 10.92 11.43 Y 0.048 0.052 1.22 1.32 Z 0.106 0.118 2.68 3.00 CASE 344-15 ISSUE AA UNIBODY PACKAGE NOTES: DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. CONTROLLING DIMENSION: INCH. D 4 PL F U H L PORT #1 POSITIVE PRESSURE (P1) PIN 1 -A- -Q- S K G -P- SQM0.25 (0.010) T SSM0.13 (0.005) Q ST 12 34 SEATING PLANE B N R C J -T- STYLE 1: PIN 1. GROUND 2. + OUTPUT 3. + SUPPL Y 4. - OUTPUT DIM MIN MAX MIN MAX MILLIMETERSINCHES A 1.145 1.175 29.08 29.85 B 0.685 0.715 17.40 18.16 C 0.305 0.325 7.75 8.26 D 0.016 0.020 0.41 0.51 F 0.048 0.064 1.22 1.63 G 0.100 BSC 2.54 BSC H 0.182 0.194 4.62 4.93 J 0.014 0.016 0.36 0.41 K 0.695 0.725 17.65 18.42 L 0.290 0.300 7.37 7.62 N 0.420 0.440 10.67 11.18 P 0.153 0.159 3.89 4.04 Q 0.153 0.159 3.89 4.04 R 0.230 0.250 5.84 6.35 S U 0.910 BSC 23.11 BSC 0.220 0.240 5.59 6.10 CASE 344B-01 ISSUE B UNIBODY PACKAGE Pressure
NOTES: DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. CONTROLLING DIMENSION: INCH. PORT #2 PORT #1 PORT #2 VACUUM (P2) (P1) SEATING PLANE SEATING PLANE K S W H L U F G D 4 PL PORT #1 POSITIVE PRESSURE -Q- 12 4 3PIN 1 -P- SSM0.13 (0.005) Q ST B N J C V R -A- STYLE 1: PIN 1. GROUND 2. + OUTPUT 3. + SUPPL Y 4. - OUTPUT DIM MIN MAX MIN MAX MILLIMETERSINCHES A 1.145 1.175 29.08 29.85 B 0.685 0.715 17.40 18.16 C 0.405 0.435 10.29 11.05 D 0.016 0.020 0.41 0.51 F 0.048 0.064 1.22 1.63 G 0.100 BSC 2.54 BSC H 0.182 0.194 4.62 4.93 J 0.014 0.016 0.36 0.41 K 0.695 0.725 17.65 18.42 L 0.290 0.300 7.37 7.62 N 0.420 0.440 10.67 11.18 P 0.153 0.159 3.89 4.04 Q 0.153 0.159 3.89 4.04 R 0.063 0.083 1.60 2.11 S U 0.910 BSC 23.11 BSC V 0.248 0.278 6.30 7.06 W 0.310 0.330 7.87 8.38 0.220 0.240 5.59 6.10 CASE 344C-01 ISSUE B UNIBODY PACKAGE NOTES: DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. CONTROLLING DIMENSION: INCH. D 4 PL F U L HPORT #2 VACUUM (P2) POSITIVE PRESSURE (P1) PIN 1 -A- -Q- S K G-P- SQM0.25 (0.010) T SSM0.13 (0.005) Q ST 12 34 SEATING PLANE B N R C J -T- STYLE 1: PIN 1. GROUND 2. + OUTPUT 3. + SUPPL Y 4. - OUTPUT DIM MIN MAX MIN MAX MILLIMETERSINCHES A 1.145 1.175 29.08 29.85 B 0.685 0.715 17.40 18.16 C 0.305 0.325 7.75 8.26 D 0.016 0.020 0.41 0.51 F 0.048 0.064 1.22 1.63 G 0.100 BSC 2.54 BSC H 0.182 0.194 4.62 4.93 J 0.014 0.016 0.36 0.41 K 0.695 0.725 17.65 18.42 L 0.290 0.300 7.37 7.62 N 0.420 0.440 10.67 11.18 P 0.153 0.159 3.89 4.04 Q 0.153 0.158 3.89 4.04 R 0.230 0.250 5.84 6.35 S U 0.910 BSC 23.11 BSC 0.220 0.240 5.59 6.10 CASE 344D-01 ISSUE B UNIBODY PACKAGE Pressure
9 Freescale Semiconductor
NOTES: DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. CONTROLLING DIMENSION: INCH. E C J V -T- PORT #1 POSITIVE PRESSURE (P1) PIN 1
4 PLD
-P- G K MQM0.25 (0.010) T U A F S N B SPM0.13 (0.005) Q ST -Q- R 4321 DIM MIN MAX MIN MAX MILLIMETERSINCHES A 1.080 1.120 27.43 28.45 B 0.740 0.760 18.80 19.30 C 0.630 0.650 16.00 16.51 D 0.016 0.020 0.41 0.51 E 0.160 0.180 4.06 4.57 F 0.048 0.064 1.22 1.63 G 0.100 BSC 2.54 BSC J 0.014 0.016 0.36 0.41 K N 0.070 0.080 1.78 2.03 P 0.150 0.160 3.81 4.06 Q 0.150 0.160 3.81 4.06 R 0.440 0.460 11.18 11.68 S 0.695 0.725 17.65 18.42 U 0.840 0.860 21.34 21.84 V 0.182 0.194 4.62 4.92 0.220 0.240 5.59 6.10 STYLE 1: PIN 1. GROUND 2. V (+) OUT 3. V SUPPL Y 4. V (-) OUT CASE 344F-01 ISSUE B UNIBODY PACKAGE Pressure
Freescale Semiconductor 10 CASE 1369-01 ISSUE B SMALL OUTLINE PACKAGE PAGE 1 OF 2 Pressure
11 Freescale Semiconductor
12 Freescale Semiconductor
Freescale Semiconductor 13 Pressure CASE 1320-02 ISSUE B MPAK
14 Freescale Semiconductor
Freescale Semiconductor 15 Pressure CASE 1320A-02 ISSUE A MPAK
Rev. 8 Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”, must be validated for each customer application by customer’s technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. Freescale and the Freescale logo are trademarks of Freescale Semiconductor, Inc., All other product or service names are the property of their respective owners. © Freescale Semiconductor, Inc. 2010. All rights reserved. How to Reach Us: Home Page: www.freescale.com Web Support: http://www.freescale.com/support USA/Europe or Locations Not Listed: Freescale Semiconductor, Inc. Technical Information Center, EL516
2100 East Elliot Road
Tempe, Arizona 85284 1-800-521-6274 or +1-480-768-2130 www.freescale.com/support Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) www.freescale.com/support Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku, Tokyo 153-0064 Japan 0120 191014 or +81 3 5437 9125 support.japan@freescale.com Asia/Pacific: Freescale Semiconductor China Ltd. Exchange Building 23F No. 118 Jianguo Road Chaoyang District Beijing 100022 China +86 010 5879 8000 support.asia@freescale.com For Literature Requests Only: Freescale Semiconductor Literature Distribution Center 1-800-441-2447 or +1-303-675-2140 Fax: +1-303-675-2150 LDCForFreescaleSemiconductor@hibbertgroup.com