DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 47
Technical content
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 1 of 47 MPU-3000/MPU-3050 Motion Processing Unit Product Specification Rev 2.9
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 2 of 47
CONTENTS
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 3 of 47
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 4 of 47
1 Document Information
1.1 Revision History
06/25/09 1.0 Initial Release 09/28/09 2.0 Changes for revision level compliance of MPU -30X0 to MPU-3000 Specification: Sec. 1.2 Added Revision B1 silicon note Sec. 1.3 Updated noise specification to 0.03º/s/√Hz Sec. 2.3 Added secondary I2C interface Sec. 3.1 Updated sensor specifications table Sec. 3.2 Changed VDD to 2.5V and TA = 250C Sec. 3.2-3.3 Changed electrical specifications table format and typical values Sec. 4.1 Updated pin-out and signal descriptions with new diagram Sec. 4.2 Updated typical operating circuit diagram Sec. 5.1 Updated new block diagram descriptions for primary and secondary I2C serial interfaces Sec. 5.9 Changed FIFO description Sec. 6 Edited digital interface Sec. 10.2 Updated package drawing/dimensions Sec. 10.7 Edited trace routing Sec. 13 Added Appendix 1.0, Errata for Revision G devices 11/5/09 2.1 Sec. 10 Added Material Handling Specification content 12/23/09 2.2 Sec. 3.2 Updated Electrical Specifications with Power -Supply Ramp Rate for VLOGIC Reference Voltage Sec. 3.3 Updated Level Output Current specifications for the Primary and Secondary I2C interfaces Sec. 3.4 Updated Frequency Variation Over Temperature Specification for Internal Clock Source Sec. 3.5.1 Updated ESD Specification Sec. 4.4 Added recommended Power-On Procedure diagram 03/15/2010 2.3 Sec. 1.4 Added new InvenSense trademarks under Applications Sec. 2.2 Edited Digital Output for 400KHz standard (not up to) Sec. 3.1 Changed Sensitivity Scale Factor to 115 LSB/(º/s) Sec. 4.4 Updated Recommended Power-on Procedure diagram Sec. 8.2 Modified Example Power Configuration diagram to remove IME - 3000 reference Sec. 11.2 Updated ESD-HBM for Device Component Level Tests. Removed all references to IME -3000 and replaced with third - party accelerometer. 08/17/2010 2.4 Sec. 3.1 Updated sensitivity scale factor, ZRO, Noise performance Sec. 3.2 Added operating current for case without DMP Added start-up time Sec. 8.2 Updated table with reference to AUX_VDDIO Sec. 9.1 Added Demo Software Section Sec. 10-11 Added Register Maps and Register Description Sections Sec. 12.9 Updated table and accompanying text Sec. 12.11 Added Storage Specifications Section Sec. 14 Added Environment Compliance Section 08/26/2010 2.4b Sec. 3.2-3.3 Updated specifications for Ci Sec. 3.5 Updated specifications for Cb Sec. 3.3 Updated VIH and Vhys
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 5 of 47 Revision Date Revision Description 12/23/2010 2.5 Sec. 9 Removed MPL section. C reated a separate document for Register Information 03/03/2011 2.6 Sec. 2.2 Clarified SPI Usage case Sec. 4.3 Fixed C1 and C2 Specifications Sec. 5.5 Clarified SPI Usage case Sec. 5.5 Documented inoperable primary bus when VDD is low and interface pins are low impedance Sec. 5.6 Documented gyro access capability in Pass-Through Mode Sec. 5.6 Documented the Secondary I 2C bus Internal Pull Up configuration Sec. 7.2 Modified diagrams to clarify usage of 3rd party accelerometers Sec. 8 Modified a ssembly rules and Moisture Sensitivity Level (MSL) Labels 05/19/2011 2.7 Sec. 1.2 Updated Software References Sec. 1.4 Added section describing InvenSense software solutions Sec. 3.2 Clarified Digital Input and Digital Output specifications Sec. 3.2 Added CLKOUT Digital Out Specifications Sec. 4.4 Clarified TVLG-VDD value Sec. 5.6 Modified diagrams for clarity Sec. 8.4.3 Clarified Trace Routing precautions Sec. 8.5 Modified Package Marking diagrams for clarity Sec. 8.8 Updated packaging images 06/13/2011 2.8 Sec. 3.5 Specified I2C Timing Specifications as only for the Primary I2C bus. Added reference to App Note for details regarding the Auxiliary I2C bus specifications. Sec. 4.1 Specified CLKIN and FSYNC to be connected to GND if unused. Sec. 4.4 Modified TVDDR value for consistency with Electrical Characteristics. Modified Power Up Sequencing Notes for clarity 11/14/2011 2.9 Sec. 3.7 Updated absolute maximum rating for acceleration Sec. 8.5 Updated package marking description
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 6 of 47
1.2 Purpose and Scope
This document is a product specification, providing a description, specifications, and design related information for the MPU-3000™ and MPU-3050™ Motion Processing Unit ™ (collectively called the MPU-30X0™). Electrical characteristics are based upon simulation results and limited characterization data of advanced samples only. Specifications are subject to change without notice. Final specifications will be updated based upon characterization of final silicon.
1.3 Product Overview
The MPU-30X0 Motion Processing Unit (MPU™) is the world’s first MotionProcessing™ solution with integrated 6-axis sensor fusion using its field-proven and proprietary MotionFusion™ engine for smart phone applications. The MPU -30X0 has an embedded 3 -axis gyroscope and Digital Motion Processor™ (DMP) hardware accelerator engine with a secondary I 2C port that interfaces to third party digital accelerometers to deliver a complete 6 -axis sensor fusion output to its primary I 2C port. This combines both linear and rotational motion into a single data strea m for the application. This breakthrough in gyroscope technology provides a dramatic 68% smaller footprint, 40% thinner package, consumes 55% less power, and has inherent cost advantages compared to the latest competitive gyro solutions to uniquely address the fast-growing demand for 6 -axis MotionProcessing in mobile handsets . The primary interface also supports SPI protocol on the MPU -3000 and can be used to read/write to all the registers on the part. The MPU’s memory and FIFO are not accessible via the SPI interface. The MPU-30X0 significantly extends and transforms motion sensing features provided by accelerometers beyond portrait and landscape orientation, to MotionProcessing functionality. The MPU measures and processes both linear and rotational m ovements, creating a higher degree of 1:1 motion interactivity between the user and their handset. Similar to the proliferation of Bluetooth, camera phone image sensors and Wi -Fi, MotionProcessing is becoming a “must -have” function in mobile handsets benefitting wireless carriers, mobile handset OEMs, application developers and end - users. By providing an integrated sensor fusion output, the DMP in the MPU-30X0 offloads the intensive MotionProcessing computation requirements from the applications processor, reducing the need for frequent polling of the motion sensor output and enabling use of low cost, low power application processors thereby increasing overall battery life of handsets. Since handsets today are of multi-function nature, MPU-30X0 not only provides accurate 1:1 motion tracking for some of the more common applications such as still/video image stabilization , gaming and dead reckoning , the 32-bit DMP can be programmed to deliver advanced UI, e.g. multiple kinds of gestures and character recognition leading to applications such as Airsign™, TouchAnywhere™, MotionCommand™. By leveraging its patented and volume -proven Nasiri -Fabrication platform, which integrates MEMS wafers with companion CMOS electronics through wafer -level bonding, InvenSense has driven the MPU-30X0 package size down to a revolutionary footprint of 4x4x0.9mm (QFN), while providing the highest performance, lowest noise, and the lowest cost semiconductor packaging to address a wide range of handheld consumer electronic devices.
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 7 of 47 The MPU-30X0 integrates 16-bit analog-to-digital converters (ADC s), selectable low -pass filters, FIFO, embedded temperature sensor, and Fast Mode I2C or SPI (MPU-3000 only) interfaces. Performance features include programmable full -scale range from ±250 degrees -per-second up to ±2000 degrees -per-second (º/s or dps ), and low -noise of 0.0 1º/s/√Hz, while providing the highest robustness supporting 10,000 g shock in operation. The highest cross -axis isolation is achieved by design from its single silicon integration. Factory-calibrated initial sensitivity reduces production -line calibration requirements. The part’s on -chip FIFO and dedicated I 2C-master accelerometer sensor bus simplify system timing and lower system power consumption . The sensor bus allows the MPU - 30X0 to directly acquire data from the off -chip accelerometer without interven tion from an external processor. Other industry -leading features include a small 4mm x4mmx0.9mm plastic QFN package , an embedded temperature sensor, programmable interrupts, and a lo w 13mW power consumption. Parts are available with I 2C and SPI serial interfaces, a VDD operating range of 2.1 to 3.6V, and a VLOGIC interface voltage from 1.71V to 3.6V. The MPU -3000 and MPU -3050 are identical, except that the MPU -3050 supports the I 2C s erial interface only, and has a separate VLOGIC reference pin (in addition to its analog supply pin, VDD), which sets the logic levels of its I 2C interface. The VLOGIC voltage may be between 1.71V min to VDD max. The MPU -3000 supports both I 2C and SPI interfaces and has a single supply pin, VDD, which is the device’s logic reference supply and the analog supply for the part. The table below outlines these differences: Primary Differences between MPU-3000 and MPU-3050 Part / Item MPU-3000 MPU-3050 VDD 2.1V to 3.6V 2.1V to 3.6V VLOGIC n/a 1.71V to VDD Serial Interfaces Supported I2C, SPI I2C Pin 8 /CS VLOGIC Pin 9 AD0/SDO AD0 Pin 23 SCL/SCLK SCL Pin 24 SDA/SDI SDA
1.4 Software Solutions
This section describes the MotionApps™ software solutions included with the InvenSense MPU ™ (MotionProcessing Unit™) and IMU (Inertial Measurement Unit) product families. Please note that the products within the IDG, IXZ, and ITG families do not include these software solutions. The MotionApps Platform is a complete software solution that in combination with the InvenSense IMU and MPU MotionProcessor ™ families delivers robust, well-calibrated 6-axis and/or 9-axis sensor fusion data using its field proven and proprietary MotionFusion™ engine. Sol ution packages are available for smartphones and tablets as well as for embedded microcontroller-based devices. The MotionApps Platform provides a turn-key solution for developers and accelerates time -to-market. It consists of complex 6/9 -axis sensor fusi on algorithms, robust multi -sensor calibration, a proven software architecture for Android and other leading operating systems, and a flexible power management scheme. The MotionApps Platform is integrated within the middleware of the target OS (the sensor framework), and also provides a kernel device driver to interface with the physical device . This directly benefits application developers by providing a cohesive set of APIs and a well -defined sensor data path in the user-space.
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 8 of 47 The table below describes the MotionApps software solutions included with the InvenSense MPU and IMU product families. InvenSense MotionProcessor Devices and Included MotionApps Software Included Software Feature MotionApps Embedded MotionApps MotionApps Lite Embedded MotionApps Lite Notes Part Number MPU-3050™ MPU-6050™ IMU-3000™ Processor Type Mobile Application Processor 8/16/32-bit Microcontroller Mobile Application Processor 8/16/32-bit Microcontroller Applications Smartphones, tablets TV remotes, health/fitness, toys, other embedded Smartphones, tablets TV remotes, health/fitness, toys, other embedded 6-Axis MotionFusion Yes Yes < 2% Application Processor load using on-chip Digital Motion Processor (DMP). Reduces processing requirements for embedded
applications
Calibration Yes Yes No-Motion calibration and temperature calibration 3rd Party Compass Cal API Yes No Integrates 3rd party compass libraries Gyro-Assisted Compass Calibration (Fast Heading) Yes No Quick compass calibration using gyroscope Magnetic Anomaly Rejection (Improved Heading) Yes No Uses gyro heading data when magnetic anomaly is detected The table below lists recommended documentation for the MotionApps software solutions. Software Documentation Platform MotionApps and MotionApps Lite Embedded MotionApps and Embedded MotionApps Lite Software Documentation Installation Guide for Linux and Android MotionApps Platform, v1.9 or later Embedded MotionApps Platform User Guide, v3.0 or later MPL Functional Specifications Embedded MPL Functional Specifications For more information about the InvenSense MotionApps Platform, please visit the Developer’s Corner or consult your local InvenSense Sales Representative.
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 9 of 47
1.5 Applications
BlurFree™ technology (for Video/Still Image Stabilization) AirSign™ technology (for Security/Authentication) TouchAnywhere™ technology (for Application Control/Navigation) MotionCommand™ technology (for Gesture Short-cuts) Motion-enabled game and application framework InstantGesture™ iG™ gesture recognition “No Touch” UI Handset gaming Location based services, points of interest, and dead reckoning Improved camera image quality through image stabilization Health and sports monitoring Power management
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 10 of 47
2 Features
The MPU-30X0 Motion Processing Unit includes a wide range of features:
2.1 Sensors
X-, Y-, Z-Axis angular rate sensors (gyros) on one integrated circuit Digital-output temperature sensor External sync signal connected to the FSYNC pin supports image, video and GPS synchronization 6-axis MotionProcessing capability using secondary I2C interface to directly connect to a digital 3- axis third-party accelerometer Factory calibrated scale factor High cross-axis isolation via proprietary MEMS design 10,000g shock tolerant
2.2 Digital Output
Fast Mode (400kHz) I2C 1MHz SPI (MPU-3000 only) to access gyro, temp and auxiliary sensor registers only; aimed at higher speed applications which need raw data, refer to Section 5.5 for further explanation 16-bit ADCs for digitizing sensor outputs Angular rate sensors ( gyros) with applications -programmable full-scale-range of ±250°/sec, ±500°/sec, ±1000°/sec, or ±2000°/sec.
2.3 MotionProcessing
Embedded Digital Motion Processing ™ (DMP™) engine supports 3D MotionProcessing and gesture recognition algorithms When used together with a digital 3 -axis third party accelerometer , the MPU-30X0 collects the accelerometer data via a dedicated interface, while synchronizing data sampling at a user defined rate. The t otal data set obtained by the MPU-30X0 includes 3-axis gyroscope data and 3-axis accelerometer data, temperature data, and the one bit external sync signal connected to the FSYNC pin. The MPU also downloads the results calculated by the digital 3 -axis thir d party accelerometer internal registers. FIFO buffers complete data set, reducing timing requirements on the system processor and saving power by letting the processor burst read the FIFO data, and then go into a low -power sleep mode while the MPU collects more data. Programmable interrupt supports features such as gestu re recognition, panning, zooming, scrolling, zero-motion detection, tap detection, and shake detection Hand jitter filter Programmable low-pass filters Feature extraction for peak and zero-crossing detection Pedometer functionality
2.4 Clocking
On-chip timing generator clock frequency ±1% over full temperature range Optional external clock inputs of 32.768kHz or 19.2MHz 1MHz clock output to synchronize with digital 3-axis accelerometer
2.5 Power
VDD supply voltage range of 2.1V to 3.6V Flexible VLOGIC reference voltage allows for multiple I2C interface voltage levels (MPU-3050 only) Power consumption with all three axes and DMP active: 6.1mA Sleep mode: 5μA Each axis can be individually powered down
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 11 of 47
2.6 Package
4x4x0.9mm QFN plastic package MEMS structure hermetically sealed and bonded at wafer level RoHS and Green compliant
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 12 of 47
3 Electrical Characteristics
3.1 Sensor Specifications
Typical Operating Circuit of Section 4.2, VDD = 2.5V, VLOGIC = 2.5V (MPU-3050 Only), TA=25°C. Parameter Conditions Min Typical Max Unit Notes GYRO SENSITIVITY Full-Scale Range FS_SEL=0 ±250 º/s 4, 7 FS_SEL=1 ±500 4, 7 FS_SEL=2 ±1000 4, 7 FS_SEL=3 ±2000 4, 7 Gyro ADC Word Length 16 bits 3 Sensitivity Scale Factor FS_SEL=0 FS_SEL=1 FS_SEL=2 FS_SEL=3 131 65.5 32.8 16.4 LSB/(º/s) 1 Sensitivity Scale Factor Tolerance 25°C -6 ±2 +6 % 1 Sensitivity Scale Factor Variation Over Temperature Nonlinearity Best fit straight line; 25°C 0.2 % 6 Cross-Axis Sensitivity 2 % 6 GYRO ZERO-RATE OUTPUT (ZRO) Initial ZRO Tolerance 25°C ±20 º/s 1 ZRO Variation Over Temperature -40°C to +85°C ±0.03 º/s/°C 8 Power-Supply Sensitivity (1-10Hz) Sine wave, 100mVpp; VDD=2.2V 0.2 º/s 5 Power-Supply Sensitivity (10 - 250Hz) Sine wave, 100mVpp; VDD=2.2V 0.2 º/s 5 Power-Supply Sensitivity (250Hz - 100kHz) Sine wave, 100mVpp; VDD=2.2V 4 º/s 5 Linear Acceleration Sensitivity Static 0.1 º/s/g 6 GYRO NOISE PERFORMANCE FS_SEL=0 Total RMS Noise DLPFCFG=2 (100Hz) 0.1 º/s-rms 1 Low-frequency RMS noise Bandwidth 1Hz to10Hz 0.033 º/s-rms 1 Rate Noise Spectral Density At 10Hz 0.01 º/s/√Hz 3 GYRO MECHANICAL FREQUENCIES X-Axis 30 33 36 kHz 1 Y-Axis 27 30 33 kHz 1 Z-Axis 24 27 30 kHz 1 GYRO START-UP TIME DLPFCFG=0 ZRO Settling to ±1º/s of Final 50 ms 5 TEMPERATURE SENSOR Range Sensitivity Untrimmed -30 to 85 280 ºC LSB/ºC Room-Temperature Offset 35oC -13200 LSB 1 Linearity Best fit straight line (-30°C to +85°C) ±1 °C 2 TEMPERATURE RANGE Specified Temperature Range -40 ºC Notes: 1. Tested in production 2. Based on characterization of 30 parts over temperature on evaluation board or in socket 3. Based on design, through modeling, and simulation across PVT 4. Typical. Randomly selected part measured at room temperature on evaluation board or in socket 5. Based on characterization of 5 parts over temperature 6. Tested on 20 parts at room temperature 7. Part is characterized to Full-Scale Range. Maximum ADC output is [216 / (Sensitivity x 2)] Example: For Sensitivity of 131 LSB/(º/s), [216 / (131 x 2)] = ±250 º/s. 8. Based on characterization of 48 parts on evaluation board or in socket
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 13 of 47
3.2 Electrical Specifications
Typical Operating Circuit of Section 4.2, VDD = 2.5V, VLOGIC = 2.5V (MPU-3050 only), TA = 25°C. Parameters Conditions Min Typical Max Units Notes VDD POWER SUPPLY Operating Voltage Range 2.1 3.6 V 2 Power-Supply Ramp Rate Monotonic ramp. Ramp rate is 10% to 90% of the final value (see Figure in Section 4.4) 0 5 ms 2 Normal Operating Current 6.1 mA 1 DMP disabled 5.9 mA 1 Sleep Mode Current 5 µA 4 VLOGIC REFERENCE VOLTAGE (must be regulated) Voltage Range VLOGIC must be ≤VDD at all times 1.71 VDD V 3, 5 Power-Supply Ramp Rate Monotonic ramp. Ramp rate is 10% to 90% of the final value 1 ms 3, 5 Normal Operating Current (see Figure in Section 4.4) Does not include pull up resistor current draw as that is system dependent 100 µA 4 START-UP TIME FOR REGISTER READ/WRITE 20 100 ms 4 I2C ADDRESS AD0 = 0 AD0 = 1 1101000 1101001 1 DIGITAL INPUTS (SDI/SDA, SCLK/SCL, FSYNC, AD0, /CS, CLKIN) VIH, High Level Input Voltage VIL, Low Level Input Voltage CI, Input Capacitance MPU-3000 MPU-3050 MPU-3000 MPU-3050 0.7*VDD 0.7*VLOGIC < 5 0.3*VDD 0.3*VLOGIC V V V V pF DIGITAL OUTPUT (SDO, INT) VOH, High Level Output Voltage VOL1, LOW-Level Output Voltage VOL.INT1, INT Low-Level Output Voltage Output Leakage Current tINT, INT Pulse Width RLOAD=1MΩ; MPU-3000 RLOAD=1MΩ; MPU-3050 RLOAD=1MΩ; MPU-3000 RLOAD=1MΩ; MPU-3050 OPEN=1, 0.3mA sink current OPEN=1 LATCH_INT_EN=0 0.9*VDD 0.9*VLOGIC 100 0.1*VDD 0.1*VLOGIC 0.1 V V V V V nA µs DIGITAL OUTPUT (CLKOUT) VOH, High Level Output Voltage VOL1, LOW-Level Output Voltage RLOAD=1MΩ RLOAD=1MΩ 0.9*VDD 0.1*VDD V V Notes: 1. Tested in production 2. Based on characterization of 30 parts over temperature on evaluation board or in socket 3. Typical. Randomly selected part measured at room temperature on evaluation board or in socket 4. Based on characterization of 5 parts over temperature 5. Refer to Section 4.4 for the recommended power-on procedure 6. Guaranteed by design
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 14 of 47
3.3 Electrical Specifications, continued
Typical Operating Circuit of Section 4.2, VDD = 2.5V, VLOGIC = 2.5V (MPU-3050 only), TA=25°C. Parameters Conditions Typical Units Notes Primary I2C I/O (SCL, SDA) VIL, LOW-Level Input Voltage MPU-3000 -0.5 to 0.3*VDD V 1 VIH, HIGH-Level Input Voltage MPU-3000 0.7*VDD to VDD + 0.5V V 1 Vhys, Hysteresis MPU-3000 0.1*VDD V 1 VIL, LOW Level Input Voltage MPU-3050 -0.5V to 0.3*VLOGIC V 1 VIH, HIGH-Level Input Voltage MPU-3050 0.7*VLOGIC to VLOGIC + 0.5V V 1 Vhys, Hysteresis MPU-3050 0.1*VLOGIC V 1 VOL1, LOW-Level Output Voltage 3mA sink current 0 to 0.4 V 1 IOL, LOW-Level Output Current VOL = 0.4V VOL = 0.6V mA mA Output Leakage Current 100 nA 2 tof, Output Fall Time from VIHmax to VILmax Cb bus capacitance in pf 20+0.1Cb to 250 ns 1 CI, Capacitance for Each I/O pin < 10 pF 3 Secondary I2C I/O (AUX_CL, AUX_DA) AUX_VDDIO=0 (MPU- 3050) VIL, LOW-Level Input Voltage -0.5V to 0.3*VLOGIC V 1 VIH, HIGH-Level Input Voltage 0.7*VLOGIC to VLOGIC + 0.5V V 1 Vhys, Hysteresis 0.1*VLOGIC V 1 VOL1, LOW-Level Output Voltage VLOGIC > 2V; 1mA sink current 0 to 0.4 V 1 VOL3, LOW-Level Output Voltage VLOGIC < 2V; 1mA sink current 0 to 0.2*VLOGIC V 1 IOL, LOW-Level Output Current VOL = 0.4V VOL = 0.6V mA mA Output Leakage Current 100 nA 2 tof, Output Fall Time from VIHmax to VILmax Cb bus capacitance in pF 20+0.1Cb to 250 ns 1 CI, Capacitance for Each I/O pin < 10 pF 3 Secondary I2C I/O (AUX_CL, AUX_DA) AUX_VDDIO=1 VIL, LOW-Level Input Voltage -0.5 to 0.3*VDD V 1 VIH, HIGH-Level Input Voltage 0.7*VDD to VDD+0.5V V 1 Vhys, Hysteresis 0.1*VDD V 1 VOL1, LOW-Level Output Voltage 1mA sink current 0 to 0.4 V 1 IOL, LOW-Level Output Current VOL = 0.4V VOL = 0.6V mA mA Output Leakage Current 100 nA 2 tof, Output Fall Time from VIHmax to VILmax Cb bus cap. in pF 20+0.1Cb to 250 ns 1 CI, Capacitance for Each I/O pin < 10 pF 3 Notes: 1. Based on characterization of 5 parts over temperature. 2. Typical. Randomly selected part measured at room temperature on evaluation board or in socket 3. Guaranteed by design
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 15 of 47
3.4 Electrical Specifications, continued
Typical Operating Circuit of Section 4.2, VDD = 2.5V, VLOGIC = 2.5V (MPU-3050 only), TA=25°C. Parameters Conditions Min Typical Max Units Notes INTERNAL CLOCK SOURCE CLK_SEL=0,1,2,3 Sample Rate, Fast DLPFCFG=0 SAMPLERATEDIV = 0 8 kHz 3 Sample Rate, Slow DLPFCFG=1,2,3,4,5, or 6 SAMPLERATEDIV = 0 1 kHz 3 Reference Clock Output CLKOUTEN = 1 1.024 MHz 3 Clock Frequency Initial Tolerance CLK_SEL=0, 25°C -5 +5 % 1 Frequency Variation over Temperature CLK_SEL=0 -15 to +10 % 2 CLK_SEL=1,2,3 +/-1 % 2 PLL Settling Time CLK_SEL=1,2,3 1 ms 4 EXTERNAL 32.768kHz CLOCK CLK_SEL=4 External Clock Frequency 32.768 kHz 4 External Clock Jitter Cycle-to-cycle rms 1 to 2 µs 4 Sample Rate, Fast DLPFCFG=0 SAMPLERATEDIV = 0 8.192 kHz 4 Sample Rate, Slow DLPFCFG=1,2,3,4,5, or 6 SAMPLERATEDIV = 0 1.024 kHz 4 Reference Clock Output CLKOUTEN = 1 1.0486 MHz 4 PLL Settling Time 1 ms 4 EXTERNAL 19.2MHz CLOCK CLK_SEL=5 External Clock Frequency 19.2 MHz 4 Sample Rate, Fast DLPFCFG=0 SAMPLERATEDIV = 0 8 kHz 4 Sample Rate, Slow DLPFCFG=1,2,3,4,5, or 6 SAMPLERATEDIV = 0 1 kHz 4 Reference Clock Output CLKOUTEN = 1 1.024 MHz 4 PLL Settling Time 1 ms 4 Notes: 1. Tested in production 2. Based on characterization of 30 parts over temperature on evaluation board or in socket 3. Typical. Randomly selected part measured at room temperature on evaluation board or in socket 4. Based on design, through modeling, and simulation across PVT
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 16 of 47
3.5 I2C Timing Characterization
Typical Operating Circuit of Section 4.2, VDD = 2.5V, VLOGIC = 1.8V±5% (MPU-3050 only) , 2.5V±5%, Parameters Conditions Min Typical Max Units Notes I2C TIMING I2C FAST-MODE fSCL, SCL Clock Frequency 0 400 kHz 1 tHD.STA, (Repeated) START Condition Hold Time 0.6 µs 1 tLOW, SCL Low Period 1.3 µs 1 tHIGH, SCL High Period 0.6 µs 1 tSU.STA, Repeated START Condition Setup Time 0.6 µs 1 tHD.DAT, SDA Data Hold Time 0 µs 1 tSU.DAT, SDA Data Setup Time 100 ns 1 tr, SDA and SCL Rise Time Cb bus cap. from 10 to 400pF 20+0.1 Cb 300 ns 1 tf, SDA and SCL Fall Time Cb bus cap. from 10 to 400pF 20+0.1 Cb 300 ns 1 tSU.STO, STOP Condition Setup Time 0.6 µs 1 tBUF, Bus Free Time Between STOP and START Condition 1.3 µs 1 Cb, Capacitive Load for each Bus Line < 400 pF 3 tVD.DAT, Data Valid Time 0.9 µs 1 tVD.ACK, Data Valid Acknowledge Time 0.9 µs 1 Notes: 1. Based on characterization of 5 parts over temperature on evaluation board or in socket 2. S = Start Condition, P = Stop Condition, Sr = Repeated Start Condition 3. Guaranteed by design Note: Specifications apply to the Primary I 2C bus only. For Auxiliary I 2C bus specifications, please refer to the Application Note, AN-MPU-3000A-20. I2C Bus Timing Diagram
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 17 of 47
3.6 SPI Timing Characterization (MPU-3000 only)
Typical Operating Circuit of Section 4.2, VDD = 2.1V to 3.6V, T A = -40°C to +85°C, unless otherwise noted. Typical values are at TA=25°C. Parameters Conditions Min Typical Max Units SPI TIMING fSCLK, SCLK Clock Frequency 0.9 1 MHz tLOW, SCLK Low Period 400 ns tHIGH, SCLK High Period 400 ns tSU.CS, CS Setup Time 8 ns tHD.CS, CS Hold Time 500 ns tSU.SDI, SDI Setup Time 11 ns tHD.SDI, SDI Hold Time 7 ns tVD.SDO, SDO Valid Time Cload = 20pF 100 ns tHD.SDO, SDO Hold Time Cload = 20pF 4 ns tDIS.SDO, SDO Output Disable Time 10 ns Note: 1. Based on characterization of 5 parts over temperature as mounted on evaluation board or in sockets SPI Bus Timing Diagram
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 18 of 47
3.7 Absolute Maximum Ratings
Stress above those listed as “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress rating s only and functional operation of the device at these conditions is not implied. Exposure to the absolute maximum ratings conditions for extended periods may affect device reliability. Absolute Maximum Ratings Parameter Rating Supply Voltage, VDD -0.5V to +6V VLOGIC Input Voltage Level (MPU-3050) -0.5V to VDD + 0.5V REGOUT -0.5V to 2V Input Voltage Level (CLKIN, AUX_DA, AD0, FSYNC, INT, SCL, SDA) -0.5V to VDD + 0.5V CPOUT (2.1V ≤ VDD ≤ 3.6V ) -0.5V to 30V Acceleration (Any Axis, unpowered) 10,000g for 0.2ms Operating Temperature Range -40°C to +105°C Storage Temperature Range -40°C to +125°C Electrostatic Discharge (ESD) Protection 1.5kV (HBM); 200V (MM) Latch-up JEDEC Class II (2),125°C Level B, ±60mA
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 19 of 47
4 Applications Information
4.1 Pin Out and Signal Description
3050 Pin Name Pin Description
1 Y Y CLKIN External reference clock input. Connect to GND if unused. 6 Y Y AUX_DA Interface to a 3rd party accelerometer, SDA pin. Logic levels are set to be either VDD or VLOGIC. See Section 6 for more details. 7 Y Y AUX_CL Interface to a 3rd party accelerometer, SCL pin. Logic levels are set to be either VDD or VLOGIC. See Section 6 for more details.
8 Y /CS SPI chip select (0=SPI mode, 1= I2C mode)
8 Y VLOGIC Digital I/O supply voltage. VLOGIC must be ≤ VDD at all times.
9 Y AD0 / SDO I2C Slave Address LSB (AD0); SPI serial data output (SDO)
9 Y AD0 I2C Slave Address LSB
10 Y Y REGOUT Regulator filter capacitor connection
11 Y Y FSYNC Frame synchronization digital input. Connect to GND if unused.
12 Y Y INT Interrupt digital output (totem pole or open-drain)
13 Y Y VDD Power supply voltage and Digital I/O supply voltage
18 Y Y GND Power supply ground
19 Y Y RESV Reserved. Do not connect.
20 Y Y CPOUT Charge pump capacitor connection
21 Y Y RESV Reserved. Do not connect.
22 Y Y CLKOUT 1MHz clock output for third-party accelerometer synchronization
23 Y SCL / SCLK I2C serial clock (SCL); SPI serial clock (SCLK)
23 Y SCL I2C serial clock
24 Y SDA / SDI I2C serial data (SDA); SPI serial data input (SDI)
24 Y SDA I2C serial data
2, 3, 4, 5, 14, 15, 16, 17 Y Y NC Not internally connected. May be used for PCB trace routing. 7 8 9 10 11 12 AUX_CL VLOGIC AD0 REGOUT FSYNC INT NC NC NC VDD NC GND NC NC NC AUX_DA NC CLKIN 24 23 22 21 20 19 RESV CPOUT RESV CLKOUT SCL SDA MPU-3050 24-pin, 4mm x 4mm x 0.9mm Orientation of Axes of Sensitivity and Polarity of Rotation 7 8 9 10 11 12 AUX_CL /CS AD0 / SDO REGOUT FSYNC INT NC NC NC VDD NC GND NC NC NC AUX_DA NC CLKIN 24 23 22 21 20 19 RESV CPOUT RESV CLKOUT SCL / SCLK SDA / SDI MPU-3000 24-pin, 4mm x 4mm x 0.9mm MPU-3000 MPU-3050 +X+Y
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 20 of 47
4.2 Typical Operating Circuits
Typical Operating Circuits 7 8 9 10 11 12 24 23 22 21 20 19 MPU-3000 CLKIN /CS GND GND GND FSYNC INT GND VDD SCL / SCLK SDA / SDI C3 2.2nF 0.1µF 0.1µF AD0 7 8 9 10 11 12 24 23 22 21 20 19 MPU-3050 CLKIN GND GND GND FSYNC INT GND VDD SCL SDA 2.2nF 0.1µF 0.1µF GND VLOGIC 10nF AUX_CL AUX_DA AUX_CL AUX_DA CLKOUT CLKOUT
4.3 Bill of Materials for External Components
Component Label Specification Quantity Regulator Filter Capacitor C1 Ceramic, X7R, 0.1µF ±10%, 2V 1 VDD Bypass Capacitor C2 Ceramic, X7R, 0.1µF ±10%, 4V 1 Charge Pump Capacitor C3 Ceramic, X7R, 2.2nF ±10%, 50V 1 VLOGIC Bypass Capacitor C4* Ceramic, X7R, 10nF ±10%, 4V 1 *MPU-3050 only
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 21 of 47
4.4 Recommended Power-on Procedure
- VLOGIC amplitude must always be ≤VDD amplitude 2. TVDDR is VDD rise time: Time for VDD to rise from 10% to 90% of its final value 3. TVDDR is ≤5ms 4. TVLGR is VLOGIC rise time: Time for VLOGIC to rise from 10% to 90% of its final value 5. TVLGR is ≤1ms 6. TVLG-VDD is the delay from the start of VDD ramp to the start of VLOGIC rise 7. TVLG-VDD is ≥0ms; 8. VDD and VLOGIC must be monotonic ramps 90% 10% 90% 10% TVLG - VDD
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 22 of 47
5 Functional Overview
5.1 Block Diagram
(/CS) AD0 / (SDO) SCL / (SCLK) SDA / (SDI) Temp Sensor ADC ADCZ Gyro Signal Conditioning ADCY Gyro Signal Conditioning ADCX Gyro Signal Conditioning Digital Motion Processor (DMP) FSYNC Primary I2C or SPI Serial Interface Secondary I2C Serial Interface Config Register Clock CPOUT Secondary Interface Bypass Mux AUX_CL AUX_DA INT12 Sensor Register OTP FIFO Interrupt Status Register VDD Bias & LDO GND REGOUT 13 18 10 [VLOGIC] Note: Pin names in round brackets ( ) are MPU-3000 only Pin names in square brackets [ ] are MPU-3050 only CLKIN CLKOUT
5.2 Overview
The MPU-30X0 is comprised of the following key blocks / functions: Three-axis MEMS rate gyroscope sensors with 16-bit ADCs and signal conditioning Digital Motion Processor (DMP) Primary I2C and SPI (MPU-3000 only) serial communications interfaces Secondary I2C serial interface for 3rd party accelerometer or other sensors Clocking Sensor Data Registers FIFO Interrupts Digital-Output Temperature Sensor Bias and LDO Charge Pump
5.3 Three-Axis MEMS Gyroscope with 16-bit ADCs and Signal Conditioning
The MPU-30X0 consists of three independent vibratory MEMS rate gyroscopes, which detect rotation about the X, Y, and Z axes. When the gyros are rotated about any of the sense axes , the Coriolis Effect causes a vibration that is detected by a capacitive pickoff. The resulting signal is amplified, demodula ted, and filtered to produce a voltage that is proportional to the angular rate. This voltage is digitized using individual on-chip 16-bit Analog-to-Digital Converters (ADCs) to sample each axis. The full -scale range of the gyro sensors may be digitally programmed to ±250, ±500, ±1000, or ±2000 degrees per second (dps). ADC sample rate is programmable from 8,000 samples per second , down to 3.9 samples per second , and user -selectable low- pass filters enable a wide range of cut-off frequencies.
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 23 of 47
5.4 Digital Motion Processor
The embedded Digital Motion Processor (DMP) is located within the MPU-30X0 and offloads computation of motion processing algorithms from the host processor. The DMP acquires data from accelerometers, gyroscopes, and additional sensors such as magnetometers, and processes the data. Th e resulting data can be read from the DMP’s registers, or can be buffered in a FIFO. The DMP has access to some of MPU’s external pins, which can be used for synchronizing external devices to the motion sensors, or generating interrupts for the application. The purpose of the DMP is to offload both timing requirements and processing power from the host processor. Typically, motion processing algorithms should be run at a high rate, often around 200Hz, in order to provide accurate results with low latency. This is required even if the application updates at a much lower rate; for example, a low power user interface may update as slowly as 5Hz, but the motion processing should still run at 200Hz. The DMP can be used as a tool in order to minimize power, simpl ify timing and software architecture, and save valuable MIPS on the host processor for use in the application.
5.5 Primary I2C and SPI Serial Communications Interfaces
The MPU-30X0 has a primary I2C serial interface and the MPU -3000 also supports SPI protocol on the primary interface. SPI interface can be used to read/write to all the registers of MPU -3000 but the MPU’s memory and FIFO are not accessible via the SPI interface. MPU-30X0 always acts as a slave when communicating to the system processor. The logic level for communications to the master is set by the voltage on the VLOGIC pin ( MPU-3050) or by VDD (MPU -3000). The LSB of the of the I 2C slave address is set by pin 9 (AD0). I2C and SPI protocols are described in more detail in Section 6. Note: When VDD is low, the primary I 2C or SPI (MPU -3000 only) interface pins become low impedance and thus can load the serial bus. This is a concern if other devices are active on the bus during this time. SPI Usage Cases (MPU-3000 only): MPU-3000 Application Processor Primary SPI Interface External Sensor Auxiliary I2C Interface Gyro Registers Temp Registers Ext. Sensor Registers Configure Registers Accessing Raw Sensor Data and Configuring MPU-3000 using SPI interface Primary interface on the MPU-3000 supports SPI protocol and this feature was designed in keeping in mind high speed applications which need access to raw sensor data. As depicted in the above diag ram all the
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 24 of 47 sensor registers can be accessed using the SPI interface and the MPU-3000 can be configured through the SPI interface. MPU’s memory and FIFO are not accessible via the SPI interface. MPU-3000 Application Processor OIS Controller MUX I2C SPIPrimary I2C/SPI Interface I2C or SPI Select Dual Mode Operation Using SPI The MPU -3000’s SPI interface can also be used in a dual -mode configuration as shown above. In this configuration, the application processor accesses all the functions of MPU-3000 using the I2C interface of the MPU-3000, and the OIS controller accesses only raw data from the MPU-3000 gyroscope registers using the SPI interface. The multiplexer ( MUX) is used to select which interface device is connected to the primary serial interface of the MPU -3000. The figure above is simplified, since there needs to be communication between the application processor and the OIS controller, and this is not shown.
5.6 Secondary I2C Serial Interface (for a third-party Accelerometer or other sensors)
The MPU-30X0 has a secondary I 2C bus for communicating to an off-chip 3-axis digital output accelerometer. This bus has two operating modes: I2C Master Mode, where the MPU-30X0 acts as a master to an external accelerometer connected to the secondary I2C bus; and Pass-Through Mode, where the MPU- 30X0 directly connects the primary and secondary I 2C buses together, to allow the system processor to directly communicate with the external accelerometer. Secondary I2C Bus Modes of Operation: I2C Master Mode: allows the MPU-30X0 to directly access the data registers of an external digital accelerometer. In this mode, the MPU-30X0 directly obtains sensor data from accelerometers and optionally, another sensor (such as a magnetometer), thus allowing the on-chip DMP to generate sensor fusion data without intervention from the system applications processor. In I 2C master mode, the MPU-30X0 can be configured to perform burst read s, returning the following data from the accelerometer: X accelerometer data (2 bytes) Y accelerometer data (2 bytes) Z accelerometer data (2 bytes) Pass-Through Mode: allows an external system processor to act as master and directly communicate to the external accelerometer connected to the secondary I 2C bus pins ( AUX_DA and AUX_CL). This is useful for configuring the accelerometers, or for keeping the MPU-30X0 in a low- power mode, when only accelerometers are to be used. In this mode, the secondary I 2C bus control logic (third-party accelerometer Interface block) of the MPU-30X0 is disabled, and the secondary I2C pins AUX_DA and AUX_CL (Pins 6 and 7) are connected to the main I2C bus (Pins 23 and 24) through analog switches. In the Pass-Through Mode the system processor can still access MPU -30X0 gyro data through the I2C interface.
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 25 of 47 Secondary I2C Bus IO Logic Levels The logic levels of the secondary I 2C bus can be programmed to be either VDD or VLOGIC (see Sections 6 and 7). Secondary I2C Bus Internal Pull-up Configuration I2C Master Mode Equivalent Circuit: The simplified equivalent circuit diagram below shows the MPU- 30X0 auxiliary I²C interface while in master mode. It should be noted that the AUX_CL pin is output only and is driven by a CMOS output buffer which does not require a pull -up resistor. The AUX_DA pin is open drain and an internal pull-up resistor is enabled. The CMOS output buffer and the pull up resistor can be powered from VDD or VLOGIC. Please refer to Section 7.2 for more details. P N MPU-30X0 VLOGIC/VDD AUX_CL AUX_DA PULLUP Equivalent ~2.5k Ohm MPU-30X0 I2C Master Mode Auxiliary I2C interface – equivalent circuit
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 26 of 47 Pass-Through Mode – Equivalent Circuit: The simplified equivalent circuit diagram below shows the MPU-30X0 I²C interface during pass-through mode. Internal analog switches are used to connect the primary and auxiliary I²C interfaces together (SCL to AUX_CL through a buffer and SDA to AUX_DA pins through a level shifter). MPU-30X0 VLOGIC/VDD AUX_CL AUX_DA Level Shifter Circuit VLOGIC/VDD SCL SDA Analog switch Analog switch MPU-30X0 Pass-Through Mode Equivalent Circuit
5.7 Internal Clock Generation
The MPU-30X0 has a flexible clocking scheme, allowing for a variety of internal or external clock sources for the internal synchronous circuitry. This synchronous circuitry includes the signal conditioning and ADCs, the DMP, and various control circuits and registers. An on -chip PLL provides flexibility in the allowable input s for generating this clock. Allowable internal sources for generating the internal clock are: An internal relaxation oscillator Any of the X, Y, or Z gyros (MEMS oscillators with a drift of ±1% over temperature) Allowable external clocking sources are: 32.768kHz square wave 19.2MHz square wave The choice of which source to select for generating the int ernal synchronous clock depends on the availability of external sources and the requirements for power consumption and clock accuracy . Most likely, these requirements will vary by mode of operation. For example, in one mode, where the biggest concern is power consumption, one may wish to operate the Digital Motion Processor of the MPU-30X0 to process
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 27 of 47 accelerometer data, while keeping the gyros off . In this case, the internal relaxation oscillator is a good clock choice. However, in another mode, where the gyros are active, selecting the gyros as the clock source provides for a more-accurate clock source. Clock accuracy is important, since timin g errors directly affect the distance and angle calculations performed by the Digital Motion Processor (or by extension, by any processor). There are also start -up conditions to consider. When the MPU-30X0 initially starts up; the device operates off of its internal clock until programmed to operate from another source. This allows the user, for example, to wait for the MEMS oscillators to stabilize before they are selected as the clock source.
5.8 Clock Output
In addition, the MPU-30X0 provides a clock output, which allows the device to operate synchronously with an external digital 3-axis accelerometer. Operating synchronously provides for higher -quality sensor fusion data, since the sampling instant for the sensor data can be set to be coincident for all sensors.
5.9 Sensor Data Registers
The sensor data registers contain the latest gyro and temperature data. They are read-only registers, and are accessed via the Serial Interface. Data from these registers may be read any time, however, the interrupt function may be used to determine when new data is available.
5.10 FIFO
The MPU-30X0 contains a 512 -byte FIFO register that is accessible via the Serial Interface. The FIFO configuration register determines what data goes into it, with possible choices being gyro data , accelerometer data , temperature readings , auxiliary ADC readings , and FSYNC input . A FIFO counter keeps track of how many bytes of valid data are contained in the FIFO. The FIFO register supports burst reads. The interrupt function may be used to determine when new data is available.
5.11 Interrupts
Interrupt functionality is configured via the Interrupt Configuration register. Items that are configurable include the INT pin configuration, the interrupt latching and clearing method, and triggers for the interrupt. Items that can trigger an interrupt are (1) Clock generator locked to new reference oscillator (used when switching clock sources); (2) Digital Motion Processor Done (programmable function); (3) new data is available to be read (from the FIFO and Data registers); and (4) the MPU -30X0 did not receive an acknowledge from the accelerometer on the Secondary I 2C bus. The interrupt status can be read from the Interrupt Status register.
5.12 Digital-Output Temperature Sensor
An on -chip temperature sensor and ADC are used to measure the MPU-30X0 die temperature. The readings from the ADC can be read from the FIFO or the Sensor Data registers.
5.13 Bias and LDO
The bias and LDO section generates the internal supply and the reference voltages and currents required by the MPU-30X0. Its two inputs are an unregulated VDD of 2.1V to 3.6V and a VLOGIC logic reference supply voltage of 1.71V to VDD (MPU-3050 only). The LDO output is bypassed by a 0.1µF capacitor at REGOUT.
5.14 Charge Pump
An on-board charge pump generates the high voltage required for the MEMS oscillators. Its output is bypassed by a 2.2nF capacitor at CPOUT.
5.15 Chip Version
The chip version is written into OTP memory.
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 28 of 47
6 Digital Interface
6.1 I2C and SPI (MPU-3000 only) Serial Interfaces
The internal registers and memory of the MPU -3000/MPU-3050 can be accessed using either I 2C or SPI (MPU-3000 & raw sensor data only ). SPI operates in four-wire mode. Serial Interface Pin Number MPU-3000 MPU-3050 Pin Name Pin Description
8 Y /CS SPI chip select (0=SPI mode, I 2C disable, 1= I 2C mode, SPI
disable) 8 Y VLOGIC Digital I/O supply voltage. VLOGIC must be ≤ VDD at all times. Note 1: To prevent switching into I 2C mode when using SPI (MPU-3000), the I 2C interface should be disabled by setting the I2C_IF_DIS configuration bit in the WHO_AM_I register. Setting this bit should be performed immediately after waiting the time specified by the “Start-Up Time for Register Read/Write” in Section 3.2.
6.1.1 I2C Interface
I2C is a two -wire interface comprised of the signals serial data (SDA) and serial clock (SCL). In general, the lines are open -drain and bi -directional. In a generalized I 2C interface implementation, attached devices can be a master or a slave. The master device puts the slave address on the bus, and the slave device with the matching address acknowledges the master. The MPU-30X0 always operates as a slave device when communicating to the system processor, which thus acts as the master. SDA and SCL lines typically need pull -up resistors to VDD. The maximum bus speed is 400kHz. The slave address of the MPU -30X0 is b110100X which is 7 bits long. The LSB bit of the 7 bit address is determined by the logic level on pin ADO. This allows two MPU -30X0s to be connected to the same I 2C bus. When used in this configuration, the address of the one of the devices should be b1101000 (p in ADO is logic low) and the address of the other should be b1101001 (pin AD0 is logic high). The I 2C address is stored in WHO_AM_I register. I2C Communications Protocol START (S) and STOP (P) Conditions Communication on the I 2C bus starts when the master puts the START condition (S) on the bus, which is defined as a HIGH -to-LOW transition of the SDA line while SCL line is HIGH (see figure below). The bus is considered to be busy until the master puts a STOP condition (P) on the bus, which is defined as a LOW to HIGH transition on the SDA line while SCL is HIGH (see figure below). Additionally, the bus remains busy if a repeated START (Sr) is generated instead of a STOP condition.
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 29 of 47 SDA SCL S START condition STOP condition P START and STOP Conditions Data Format / Acknowledge I2C data bytes are defined to be 8 bits long. There is no restriction to the number of bytes transmitted per data transfer. Each byte transferred must be followed by an acknowledge (ACK) signal. The clock for the acknowledge signal is generated by the master, while the receiver generates the actual acknowledge signal by pulling down SDA and holding it low during the HIGH portion of the acknowledge clock pulse. If a slave is busy and is unable to transmit or receive another byte of data until some other task has been performed, it can hold SCL LOW, thus forcing the master into a wait state. Normal data transfer resumes when the slave is ready, and releases the clock line (refer to the following figure). DATA OUTPUT BY TRANSMITTER (SDA) DATA OUTPUT BY RECEIVER (SDA) SCL FROM MASTER START condition clock pulse for acknowledgement acknowledge not acknowledge 1 2 8 9 Acknowledge on the I2C Bus Communications After beginning communications with the START condition (S), the master sends a 7 -bit slave address followed by an 8th bit, the read/write bit. The read/write bit indicates whether the master is receiving data from or i s writing to the slave device. Then, the master releases the SDA line and waits for the acknowledge signal (ACK) from the slave device. Each byte transferred must be followed by an acknowledge bit. To acknowledge, the slave device pulls the SDA line LOW and keeps it LOW for the high period of the SCL line. Data transmission is always terminated by the master with a STOP condition (P), thus freeing the communications line. However, the master can generate a repeated START condition (Sr), and address another slave without first generating a STOP condition (P). A LOW to HIGH transition on the SDA line while SCL is HIGH defines the stop condition. All SDA changes should take place when SCL is low, with the exception of start and stop conditions.
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 30 of 47 SDA START condition SCL ADDRESS R/W ACK DATA ACK DATA ACK STOP condition S P 1 – 7 8 9 1 – 7 8 9 1 – 7 8 9 Complete I2C Data Transfer To write the internal MPU -30X0 registers, the master transmits the start condition (S), followed by the I 2C address and the write bit (0). At the 9th clock cycle (when the clock is high), the MPU-30X0 acknowledges the transfer. Then the master puts the register address (RA) on the bus. After the MPU -30X0 acknowledges the reception of the register address, the master puts the register data onto the bus. This is followed by the ACK signal, and data transfer may be concluded by the stop condition (P). To write multiple bytes after the last ACK signal, the master can continue outputting data rather than transmitting a stop signal. In this case, the MPU-30X0 automatically increments the register address and loads the data to the appropriate register. The following figures show single and two-byte write sequences. Single-Byte Write Sequence Burst Write Sequence To read the internal MPU-30X0 registers, the master sends a start condition, followed by the I 2C address and a write bit, and then the register address that is going to be read. Upon receiving the ACK signal from the MPU-30X0, the master transmits a start signal followed by the slave address and read bit. As a result, the MPU-30X0 sends an ACK signal and the data. The communication ends with a not acknowledge (NACK) signal and a stop bit from master. The NACK condition is defined such that the SDA line remains high at the 9th clock cycle. The following figures show single and two-byte read sequences. Single-Byte Read Sequence Burst Read Sequence Master S AD+W RA DATA P Slave ACK ACK ACK Master S AD+W RA DATA DATA P Slave ACK ACK ACK ACK Master S AD+W RA S AD+R NACK P Slave ACK ACK ACK DATA Master S AD+W RA S AD+R ACK NACK P Slave ACK ACK ACK DATA DATA
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 31 of 47 I2C Terms Signal Description S Start Condition: SDA goes from high to low while SCL is high AD Slave I2C address W Write bit (0) R Read bit (1) ACK Acknowledge: SDA line is low while the SCL line is high at the 9th clock cycle NACK Not-Acknowledge: SDA line stays high at the 9th clock cycle RA MPU-30X0 internal register address DATA Transmit or received data P Stop condition: SDA going from low to high while SCL is high
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 32 of 47
6.1.2 SPI interface (MPU-3000 only)
SPI is a 4-wire synchronous serial interface that uses two control and two data lines. The MPU -3000 always operates as a Slave device during standard Master -Slave SPI operation. With respect to the Master, the Serial Clock output (SCLK), the Data Output (SDO) and the Data Input (SDI) are shared among the Slave devices. The Master generates an independent Chip Select (/CS) for each Slave device; /CS goes low at the start of transmission and goes back high at the end. The Serial Data Output (SDO) line, remains in a high - impedance (high-z) state when the device is not selected, so it does not interfere with any active devices. SPI Operational Features 1. Data is delivered MSB first and LSB last 2. Data is latched on rising edge of SCLK 3. Data should be transitioned on the falling edge of SCLK 4. SCLK frequency is 1MHz max 5. SPI read and write operations are completed in 16 or more clock cycles (two or more bytes). The first byte contain s the SPI Address, and the following byte(s) contain(s) the SPI data. The first bit of the first byte contains the Read/Write bit and indicates the Read (1) or Write (0) operation. The following 7 bits contain the Register Address. In cases of multiple -byte Read/Writes, data is two or more bytes: SPI Address format MSB LSB R/W A6 A5 A4 A3 A2 A1 A0 SPI Data format MSB LSB D7 D6 D5 D4 D3 D2 D1 D0 6. Supports Single or Burst Read/Writes. Typical SPI Master / Slave Configuration SPI Master SPI Slave 1 SPI Slave 2 /CS1 /CS2 SCLK SDI SDO /CS SCLK SDI SDO /CS Each SPI slave requires its own Chip Select (/CS) line. SDO, SDI and SCLK lines are shared. Only one /CS line is active (low) at a time ensuring that only one slave is selected at a time. The /CS lines of other slaves are held high which causes their respective SDO pins to be high-Z.
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 33 of 47
7 Serial Interface Considerations (MPU-3050)
7.1 MPU-3050 Supported Interfaces
The MPU -3050 supports I 2C communications on both its primary (microprocessor) serial interface and its secondary (accelerometer) interface.
7.2 Logic Levels
The MPU-3050 I/O logic levels are set to be either VDD or VLOGIC, as shown in the table below. I/O Logic Levels vs. AUX_VDDIO (Secondary I2C Bus IO Level) AUX_VDDIO MICROPROCESSOR LOGIC LEVELS (Pins: SDA, SCL, AD0,CLKIN, INT) ACCELEROMETER LOGIC LEVELS (Pins: AUX_DA, AUX_CL)
0 VLOGIC VLOGIC
1 VLOGIC VDD
Notes: 1. CLKOUT has logic levels that are always referenced to VDD 2. The power-on-reset value for AUX_VDDIO is 0. VLOGIC may be set to be equal to VDD or to another voltage, such that at all times VLOGIC is ≤ VDD. When AUX_VDDIO is set to 0 (its power -on-reset value), VLOGIC is the power supply voltage for both the microprocessor system bus and the accelerometer secondary bus, as shown in the figure of Section 7.2.1. When AUX_VDDIO is set to 1, VLOGIC is the power supply voltage for the microprocessor system bus and VDD is the supply for the accelerometer secondary bus, as shown in the figure of Section 7.2.2.
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 34 of 47
7.2.1 AUX_VDDIO = 0
The figure below shows logic levels and voltage connections for AUX_VDDIO = 0. Note: Actual configuration will depend on the type of third-party accelerometer used. MPU-30X0 3rd Party Accel SDA AUX_CL SCL AUX_DA VDD_IO VDD VDD SA0 CS INT 2 INT 1 System Processor CLKIN SYSTEM BUS VLOGIC VLOGIC VLOGIC VDD VDD VLOGIC (0V - VLOGIC) CLKOUT SCL SDA INT FSYNC VLOGIC AD0 (0V - VLOGIC) (0V - VLOGIC) (0V - VLOGIC) (0V - VLOGIC) (0V - VLOGIC) Notes: 1. AUX_VDDIO is bit 7 in Register 24, and determines the IO voltage levels of AUX_DA and AUX_CL (0 = set output levels relative to VLOGIC) 2. CLKOUT is always referenced to VDD 3. Other MPU-3050 logic IO are always referenced to VLOGIC (0V - VLOGIC) (0V - VLOGIC) (0V - VLOGIC) (0V - VLOGIC) 0V - VDD (0V, VLOGIC) No connect (0V, VLOGIC) SCL SDA I/O Levels and Connections for AUX_VDDIO = 0
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 35 of 47
7.2.2 AUX_VDDIO = 1
When AUX_VDDIO is set to 1 by the user, VLOGIC is the power supply voltage for the microprocessor system bus and VDD is the power supply for the accelerometer secondary bus, as shown in the figure below. This is useful when interfacing to a third-party accelerometer where there is only one supply for both the logic and analog sections of the 3rd party accelerometer. MPU-30X0 3rd Party Accel SDA AUX_CL SCL AUX_DA VDD VDD ADDR INT 2 INT 1 System Processor CLKIN SYSTEM BUS VLOGIC VDD Configuration 1 Configuration 2 1.8V±5% 2.5V±5% 3.0V±5% 3.0V±5% Voltage/ Configuration VLOGIC VLOGIC VDD VDD VLOGIC CLKOUT SCL SDA INT FSYNC VLOGIC AD0 (0V - VLOGIC) (0V - VLOGIC) (0V - VLOGIC) (0V - VLOGIC) AUX_VDDIO 1 1 Notes: 1. AUX_VDDIO is bit 7 in Register 24, and determines the IO voltage levels of AUX_DA and AUX_CL (1 = set output levels relative to VDD) 2. CLKOUT is always referenced to VDD 3. Other MPU-3050 logic IO are always referenced to VLOGIC 4. Third-party accelerometer logic levels are referenced to VDD; setting INT1 and INT2 to open- drain configuration provides voltage compatibility when VDD ≠ VLOGIC. When VDD = VLOGIC, INT1 and INT2 may be set to push-pull outputs, and the external pull-up resistors will not be needed. (0V - VLOGIC) (0V - VLOGIC) 0V - VDD 0V - VDD 0V - VDD DIO (0V, VLOGIC) 0V - VDD VLOGIC (0V - VLOGIC) (0V - VLOGIC) SCL SDA I/O Levels and Connections for Two Example Power Configurations ( AUX_VDDIO = 1) Note: Actual configuration will depend on the type of third-party accelerometer used.
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 36 of 47
8 Assembly
This section provides general guidelines for assembling InvenSense Micro Electro -Mechanical Systems (MEMS) gyros packaged in Quad Flat No leads package (QFN) surface mount integrated circuits.
8.1 Orientation of Axes
The diagram below shows the orientation of the axes of sensitivity and the polarity of rotation. Note the pin 1 identifier in the figure. Orientation of Axes of Sensitivity and Polarity of Rotation MPU-3000 MPU-3050 +X+Y
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 37 of 47
8.2 Package Dimensions:
SYMBOLS DIMENSIONS IN MILLIMETERS MIN NOM MAX A 0.85 0.90 0.95 A1 0.00 0.02 0.05 b 0.18 0.25 0.30 D 3.90 4.00 4.10 D2 2.95 3.00 3.05 E 3.90 4.00 4.10 E2 2.75 2.80 2.85 e --- 0.50 --- L 0.30 0.35 0.40 L1 0.35 0.40 0.45 I 0.20 0.25 0.30 R 0.05 --- 0.10 s 0.05 --- 0.15 S1 0.15 0.20 0.25 R S S A E D PIN 1 IDENTIFIER IS A LASER MARKED FEATURE ON TOP c L1 (12x) D2 L(12x) b e f I PIN 1 IDENTIFIER C 0.16 On 4 corner lead dim. 7 12 1924 712 19 24 I
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 38 of 47
8.3 PCB Design Guidelines:
The Pad Diagram using a JEDEC type extension with solder rising on the outer edge is shown below . The Pad Dimensions Table shows pad sizing (mean dimensions) recommended for the MPU-30X0 product. JEDEC type extension with solder rising on outer edge PCB Lay-out Diagram SYMBOLS DIMENSIONS IN MILLIMETERS NOM Nominal Package I/O Pad Dimensions e Pad Pitch 0.50 b Pad Width 0.25 L Pad Length 0.35 L1 Pad Length 0.40 D Package Width 4.00 E Package Length 4.00 D2 Exposed Pad Width 3.00 E2 Exposed Pad Length 2.80 I/O Land Design Dimensions (Guidelines ) D3 I/O Pad Extent Width 4.80 E3 I/O Pad Extent Length 4.80 c Land Width 0.35 Tout Outward Extension 0.40 Tin Inward Extension 0.05 L2 Land Length 0.80 L3 Land Length 0.85 PCB Dimensions Table (for PCB Lay-out Diagram)
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 39 of 47
8.4 Assembly Precautions
8.4.1 Gyroscope Surface Mount Guidelines
InvenSense MEMS Gyros sense rate of rotation. In addition, gyroscopes sense mechanical stress coming from the printed circuit board (PCB). This PCB stress can be minimized by adhering to certain design rules: When using MEMS gyroscope components in plastic packages, PCB mounting and assembly can cause package stress. This package stress in turn can affect the output offset and its valu e over a wide range of temperatures. This stress is caused by the mismatch between the Coefficient of Linear Thermal Expansion (CTE) of the package material and the PCB. Care must be taken to avoid package stress due to mounting. Traces connected to pads should be as symmetric as possible. Maximizing symmetry and balance for pad connection will help component self alignment and will lead to better control of solder paste reduction after reflow. Any material used in the surface mount assembly process of the MEMS gyroscope should be free of restricted RoHS elements or compounds. Pb-free solders should be used for assembly.
8.4.2 Exposed Die Pad Precautions
The MPU-30X0 has very low active and standby c urrent consumption. The exposed die pad is not required for heat sinking, and should not be soldered to the PCB . Failure to adhere to this rule can induce performance changes due to package thermo -mechanical stress. There is no electrical connection between the pad and the CMOS.
8.4.3 Trace Routing
Routing traces or vias under the gyro package such that they run under the exposed die pad is prohibited. Routed active signals may harmonically couple with the gyro MEMS devices, compromising gyro response. These devices are designed with the drive f requencies as follows: X = 33±3kHz, Y = 30±3kHz, and Z=27±3kHz. To avoid harmonic coupling don’t route active signals in non-shielded signal planes directly below, or above the gyro package. Note: For best performance, design a ground plane under the e -pad to reduce PCB signal noise from the board on which the gyro device is mounted. If the gyro device is stacked under an adjacent PCB board, design a ground plane directly above the gyro device to shield active signals from the adjacent PCB board.
8.4.4 Component Placement
Do not place large insertion components such as keyboard or similar buttons, connectors, or shielding boxes at a distance of less than 6 mm from the MEMS gyro. Maintain generally accepted industry design practices for component placement near the MPU-30X0 to prevent noise coupling and thermo-mechanical stress.
8.4.5 PCB Mounting and Cross-Axis Sensitivity
Orientation errors of the gyroscope mounted to the printed circuit board can cause cross -axis sensitivity in which one gyro responds to rotation about another axis . For example, the X -axis gyroscope may respond to rotation about the Y or Z axes. The orientation mounting errors are illustrated in the figure below.
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 40 of 47 Package Gyro Axes ( ) Relative to PCB Axes ( ) with Orientation Errors (Θ and Φ) MPU-3000 MPU-3050 Φ Θ X Y Z The table below shows the cross-axis sensitivity of the gyroscope for a given orientation error. Cross-Axis Sensitivity vs. Orientation Error Orientation Error (θ or Φ) Cross-Axis Sensitivity (sinθ or sinΦ) 0º 0% 0.5º 0.87% 1º 1.75% The specification for cross -axis sensitivity in Section 3.1 includes the effect of the die orientation error with respect to the package.
8.4.6 MEMS Handling Instructions
MEMS (Micro Electro -Mechanical Systems) are a time -proven, robust technology used in h undreds of millions of consumer, automotive and industrial products. MEMS devices consist of microscopic moving mechanical structures. They differ from conventional IC products, even though they can be found in similar packages. Therefore, MEMS devices req uire different handling precautions than conventional ICs prior to mounting onto printed circuit boards (PCBs). The MPU -30X0 gyroscope has been qualified to a shock tolerance of 10,000 g. InvenSense packages its gyroscopes as it deems proper for protection against normal handling and shipping. It recommends the following handling precautions to prevent potential damage. Do not drop individually packaged gyroscopes, or trays of gyroscopes onto hard surfaces. Components placed in trays could be subject to g-forces in excess of 10,000g if dropped. Printed circuit boards that incorporate mounted gyroscopes should not be separated by manually snapping apart. This could also create g-forces in excess of 10,000g.
8.4.7 ESD Considerations
Establish and use ESD-safe handling precautions when unpacking and handling ESD-sensitive devices. Store ESD sensitive devices in ESD safe containers until ready for use. The Tape -and-Reel moisture- sealed bag is an ESD approved barrier. The best practice is to keep the units in the original moisture sealed bags until ready for assembly. Restrict all device handling to ESD protected work areas that measure less than 200V static charge. Ensure that all workstations and personnel are properly grounded to prevent ESD.
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 41 of 47
8.4.8 Reflow Specification
Qualification Reflow: The MPU -30X0 gyroscope was qualified in accordance with IPC/JEDEC J -STD- 020D.01. This standard classifies proper packaging, storage and handling in order to avoid subsequent thermal and mechanical damage during the solder reflow attachment phase of assembly. The classification specifies a sequence consisting of a bake cycle, a moisture soak cycle in a temperature humidity oven, followed by three solder reflow cycles and functional testing for qualificatio n. All temperatures refer to the topside of the QFN package, as measured on the package body surface. The peak solder reflow classification temperature requirement is (260 +5/ -0°C) for lead-free soldering of components measuring less than 1.6 mm in thickness. Production Reflow: Check the recommendations of your solder manufacturer. For optimum results, production solder reflow processes should reduce exposure to high temperatures, and use lower ramp -up and ramp-down rates than those used in the component qualification profile shown for reference below. Production reflow should never exceed the maximum constraints listed in the table and shown in the figure below. These constraints were used for the qualification profile, and represent the maximum tolerable ratings for the device. Maximum Temperature IR / Convection Solder Reflow Curve Used for Qualification Temperature Set Points for IR / Convection Reflow Corresponding to Figure Above Step Setting CONSTRAINTS Temp (°C) Time (sec) Rate (°C/sec) A Troom 25 B TSmin 150 C TSmax 200 60 < tBC < 120 D TLiquidus 217 r(TLiquidus-TPmax) < 3 E TPmin [255°C, 260°C] 255 r(TLiquidus-TPmax) < 3 F TPmax [ 260°C, 265°C] 260 tAF < 480 r(TLiquidus-TPmax) < 3 G TPmin [255°C, 260°C] 255 10< tEG < 30 r(TPmax-TLiquidus) < 4 H TLiquidus 217 60 < tDH < 120 I Troom 25 Note: For users TPmax must not exceed the classification temperature (260°C). For suppliers TPmax must equal or exceed the classification temperature.
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 42 of 47
8.4.9 Storage Specifications
The storage specification of the MPU-30X0 gyroscope conforms to IPC/JEDEC J-STD-020D.01 Moisture Sensitivity Level (MSL) 3. Calculated shelf-life in moisture-sealed bag 12 months -- Storage conditions: <40°C and <90% RH After opening moisture-sealed bag 168 hours -- Storage conditions: ambient ≤30°C at 60%RH
8.5 Package Marking Specification
Y Y = Year Code W W = Work Week TOP VIEW INVENSENSE MPU-3050 X X X X X X-X X X X Y Y W W X Package Marking Specification
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 43 of 47
8.6 Tape & Reel Specification
Reel Dimensions and Package Size PACKAGE SIZE REEL (mm) L V W Z 4x4 330 100 13.2 2.2
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 44 of 47 Tape and Reel Specification Reel Specifications Quantity Per Reel 5,000 Reels per Box 1 Boxes Per Carton (max) 3 Pieces per Carton (max) 15,000
8.7 Label
(Anti-Static) Carrier Tape (Anti-Static) Label Reel Terminal Tape
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 45 of 47
8.8 Packaging
Tape & Reel Barcode Label Reel in Box Box with Tape & Reel Label Moisture-Sensitive Caution Label
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 46 of 47
9 Reliability
9.1 Qualification Test Policy
Before InvenSense product s are released for production, they complete a series of q ualification tests. The Qualification Test Plan for the MPU -30X0 followed the JEDEC JESD47G.01 Standard, “Stress-Test-Driven Qualification of Integrated Circuits.” The individual tests are described below.
9.2 Qualification Test Plan
/ Lot Acc / Reject Criteria High Temperature Operating Life (HTOL/LFR) JEDEC JESD22-A108C, Dynamic, 3.63V biased, Tj>125°C [read-points 168, 500, 1000 hours] 3 77 (0/1) Highly Accelerated Stress Test (1) (HAST) JEDEC JESD22-A118 Condition A, 130°C, 85%RH, 33.3 psia., unbiased, [read-point 96 hours] 3 77 (0/1) High Temperature Storage Life (HTS) JEDEC JESD22-A103C, Cond. A, 125°C, Non-Biased Bake [read-points 168, 500, 1000 hours] 77 (0/1) Device Component Level Tests TEST Method/Condition Lot Quantity Sample / Lot Acc / Reject Criteria ESD-HBM JEDEC JESD22-A114F, (1.5KV) 1 3 (0/1) ESD-MM JEDEC JESD22-A115-A, (200V) 1 3 (0/1) Latch Up JEDEC JESD78B Class II (2), 125°C; Level B ±60mA 1 6 (0/1) Mechanical Shock JEDEC JESD22-B104C, Mil-Std-883H, method 2002.5, Cond. E, 10,000g’s, 0.2ms, ±X, Y, Z – 6 directions, 5 times/direction (0/1) Vibration JEDEC JESD22-B103B, Variable Frequency (random), Cond. B, 5-500Hz, X, Y, Z – 4 times/direction 3 5 (0/1) Temperature Cycling (TC) (1) JEDEC JESD22-A104D Condition N, [-40°C to +85°C], Soak Mode 2 [5’], 100 cycles 3 77 (0/1) Board Level Tests TEST Method/Condition Lot Quantity Sample / Lot Acc / Reject Criteria Board Mechanical Shock JEDEC JESD22-B104C, Mil-Std-883H, method 2002.5, Cond. E, 10000g’s, 0.2ms, +-X, Y, Z – 6 directions, 5 times/direction (0/1) Board Temperature Cycling (TC) (1) JEDEC JESD22-A104D Condition N, [ -40°C to +85°C], Soak Mode 2 [5’], 100 cycles 1 40 (0/1) (1) Tests are preceded by MSL3 Preconditioning in accordance with JEDEC JESD22-A113F
MPU-3000/MPU-3050 Product Specification Document Number: PS-MPU-3000A-00 Revision: 2.9 Release Date: 11/14/2011 47 of 47
10 Environmental Compliance
The MPU-30X0 is RoHS and Green compliant. The MPU -30X0 is in full environmental compliance as evidenced in report HS -MPU-30X0A, Materials Declaration Data Sheet. Environmental Declaration Disclaimer: InvenSense believes this environmental information to be correct but cannot guarantee accuracy or completeness. Conformity documents for the above component constitutes are on file. InvenSense subcontracts manufacturing and the information containe d herein is based on data received from vendors and suppliers, which has not been validated by InvenSense. This information furnished by InvenSense is believed to be accurate and reliable. However, no responsibility is assumed by In venSense for its use, or for any infringements of patents or other rights of third parties that may result from its use. Specificat ions are subject to change without notice. InvenSense reserves the right to make changes to this product, including its circuits and software, in order to improve its design and/or performance, without prior notice. InvenSense makes no warranties, neither expressed nor implied, regarding the information and specifications contained in this document. InvenSense assumes no responsibility for any claims or damages arising from information contained in this document, or from the use of products and services det ailed therein. This includes, but is not limited to, claims or damages based on the infringement of patents, copyrights, mask work and/or other intellectual property rights. Certain intellectual property owned by InvenSense and described in this document is patent protected. No license is granted by implication or otherwise under any patent or patent rights of InvenSense. This publication supersedes and replaces all inform ation previously supplied. Trademarks that are registered trademarks are the propert y of their respective companies. InvenSense sensors should not be used or sold in the development, storage, production or utilization of any conventional or mass-destructive weapons or for any other weapons or life threatening applications, as well as in a ny other life critical applications such as medical equipment, transportation, aerospace and nuclear instruments, undersea equipment, power plant equipment, disaster prevention and crime prevention equipment. InvenSense®, AirSign®, TouchAnywhere ®, and Mo tionCommand®, are registered trademarks of InvenSense, Inc. , MPU™, MPU- 30X0™, MPU-3000™, MPU-3050™, MPU-6050™, IMU-3000™, Motion Processing Unit™, Digital Motion Processor™, Digital Motion Processing™, DMP ™, MotionApps™, MotionProcessing™, MotionProcessor™, MotionFusion™, InstantGesture™, iG ™, and BlurFree™ are trademarks of InvenSense, Inc. ©2011 InvenSense, Inc. All rights reserved.