MPP10

MPP102WF1000T2E MULTICOMP | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 7

Technical content

Page <1> V1.028/07/23 Thick Film Chip Resistors Newark.com/multicomp-pro Farnell.com/multicomp-pro sg.element14.com/b/multicomp-pro Scope: This specification for approval relates to Ultra - High Power Thick Film Chip Resistors Ratings: Type MPP10 (2010) MPP12 (2512) MPP17 (2817) MPP20 (4320) MPP27 (4527) Power Rating at 70°C 2W 3W 4W 5W 6W Max. Working Voltage 200 V 250 V 250 V 300 V 300 V Max. Overload Voltage 500 V 500 V 500 V 600 V 600 V Dielectric Withstanding Voltage 500 V 500 V 500 V 600 V 600 V Temperature Range -55°C to +155°C Ambient Temperature 70°C Voltage rating: Resistors shall have a rated direct-current (DC) continuous working voltage or an approximate sine-wave root-mean-square (RMS) alternating-current (AC) continuous working voltage at commercialline frequency and waveform corresponding to the power rating , as determined from the following formula : RCWV = √P x R Note : Max. Working Voltage or √P x R whichever is lesser Max. Overload Voltage or 2.5 √P x R whichever is lesser Where : RCWV = Rated DC or RMS AC continuous working voltage at commercial-line frequency and waveform (volt) P = Power Rating (watt) R = Nominal Resistance (ohm) Nominal Resistance Effective figures of nominal resistance shall be in accordance : E-24 values – these are preferred and will have standard MOQ E-96 values – are available on case by case basis and availability and MOQ need to be confirmed with factory first

Page <2> V1.028/07/23 Thick Film Chip Resistors Newark.com/multicomp-pro Farnell.com/multicomp-pro sg.element14.com/b/multicomp-pro Construction Power rating and dimensions Power rating: Resistors shall have a power rating based on continuous load operation at an ambient temperature of 70°C. For temperature in excess of 70°C, The load shall be derate as shown in figure 1.

Page <3> V1.028/07/23 Thick Film Chip Resistors Newark.com/multicomp-pro Farnell.com/multicomp-pro sg.element14.com/b/multicomp-pro Dimension Type Dimension (mm) L W H ℓ1 ℓ2 MPP10 (2010) 5.00 ± 0.10 2.50 ± 0.15 1.10 ± 0.10 Dimensions : Millimetres Power Rating Type Power Rating at 70°C Tolerance % Resistance Range Standard Series MPP10 (2010) 2W 1Ω to 10MΩ E-96 ±5 E-24 MPP12 (2512) 3W ±1 E-96 ±5 E-24 MPP17 (2817) 4W ±1 E-96 ±5 E-24 MPP20 (4320) 5W ±1 E-96 ±5 E-24 MPP27 (4527) 6W ±1 E-96 ±5 E-24

Page <4> V1.028/07/23 Thick Film Chip Resistors Newark.com/multicomp-pro Farnell.com/multicomp-pro sg.element14.com/b/multicomp-pro Performance specification Characteristics Limits Test Methods (AEC - Q200) Operational Life Resistance change rate is 125°C, at 35% of operating power, 1000H(1.5 hours “ON”, 0.5 hour “OFF”) (MIL-STD-202 Method 108) Temperature Coefficient Resistance change rate is 10Ω< R ≤10Ω : ±200PPM/°C 10Ω< R ≤10MΩ : ±100PPM/°C 4.8 Natural resistance change per temp. degree centigrade. R2-R1 R1(t2-t1) R1: Resistance value at room temperature (T1) R2: Resistance value at room temp. plus 100°C (T2) Test pattern: room temp. (T1), room temp. +100°C (T2) Short Time Overload Resistance change rate is 2.5x Rated voltage or Max. Overload Voltage whichever is lower for 5 seconds, then check the resistance. External Visual No Mechanical Pamage Electrical test not required.Inspect device construction, marking and workmanship (MIL-STD-883 Method 2009) Physical Dimension Reference 2.0 Dimension Standards Verify physical dimensions to the applicable device detail specification. Note: User(s) and Suppliers spec. Electrical test not required. (JESD22 MH Method JB-100) Resistance to Solvent Marking Unsmeared Note: Add Aqueous wash chemical – OKEM Clean or equivalent. Do not use banned solvents. ( MIL-STD-202 Method 215) Terminal Strength Not broken Force of 1.8kg for 60 seconds. (JIS-C-6429) High Temperature Expo- sure (Storage) Resistance change rate is ±(1.0%+0.1Ω)max 1000hrs. at T=155°C.Unpowered. Measurement at 24±2 hours after test conclusion. (MIL-STD-202 Method 108) Temperature cycling Resistance change rate is 1000 Cycles (-55°C to +155°C). Measurement at 24±2 hours after test conclusion. (JESD22 Method JA-104) Moisture Resistance Resistance change rate is T=24 hours /cycle. Unpowered. Measurement at 24±2 hours after test conclusion. (MIL-STD-202 Method 106)

Page <5> V1.028/07/23 Thick Film Chip Resistors Newark.com/multicomp-pro Farnell.com/multicomp-pro sg.element14.com/b/multicomp-pro Characteristics Limits Test Methods (AEC - Q200) Biased Humidity Resistance change rate is 10% rated power, 85°C/85%RH, 1000H,Measurement at 24 hours after test conclusion. (MIL-STD-202 Method 103) Mechanical Shock Resistance change rate is ±(1.0%+0.1Ω)max Wave Form: Tolerance for half sine shock pulse. Peak value is 100g’s. Normal duration (D) is 6. (MIL-STD-202 Method 213) Vibration Resistance change rate is ±(1.0%+0.1Ω)max 5g’s for 20 min., 12cycle each of 3 orientations. Note: Use 8”*5”PCB. 031” thick 7 secure points (onone) long side and 2 secure points at corners of opposite sides. Parts mounted within 2’ from any secure point. Test from 10-2000Hz. (MIL-STD-202 Method 204) Thermal Shock Resistance change rate is ±(1.0%+0.1Ω)max -55°C/+155°C,Note: Number of cycles required -300, Maximum transfer time -20 seconds, Dwell time -15 minutes. Air-Air. (MIL-STD-202 Method 107) ESD Resistance change rate is ±(10%+0.1Ω)max With the electrometer in direct contact with the discharge tip, verify the voltage setting at levels of ±500V,±1KV, ±2KV, ±4KV, ±8KV, The electrometer reading shall be within ±10% for voltages from 500V to 800V. (AEC-Q200-002) Solderability 95% coverage Min. For both leaded & SMD. Electrical test not required. Magnification 50X. Conditions: a) Method B 4hrs at 155°C dry heat, the dip in bath with 245°C,5s. b) Method B: at 215°C,5s. c) Method D: at 260°C, 60s. ( J-STD-002) Flammability No ignition of the tissue paper or scorching or the pinewood board V-0 or V-1 are acceptable. Electrical test not required. (UL-94) Board Flex Resistance change rate is ±(1%+0.05Ω)max 2mm (Min) (JIS-C-6429) Flame Retardance No flame Temperature sensing at 500°C, Voltage power subjected to 32V DC current clamped up to 500A DC and decreased in 1.0V DC/hour. (AEC-Q200-001) Resistance to Soldering Heat Resistance change rate is ±(1%+0.05Ω)max. Condition B No per-heat of samples. Note: Single Wave Solder-Procedure 2 for SMD and Procedure 1 for Leaded with solder within 1.5mm of device body. (MIL-STD-202 Method 210) * Sulfuration test: H 2S 3~5PPM 50°C±2°C 91%~93%RH 1000H

Page <6> V1.028/07/23 Thick Film Chip Resistors Newark.com/multicomp-pro Farnell.com/multicomp-pro sg.element14.com/b/multicomp-pro Packing specification Tapping Dimension Type A ±0.1 B ±0.1 C ±0.15 ØD +0.1 MPP10 (2010) 2.65 5.25 2 1.5 1.75 5.5 12 1 1.35 MPP12 (2512) 3.5 6.7 5.5 12 1.5 MPP17 MPP17 (2817) 5.4 11.5 11.5 24 - MPP27 (4527) 7.2 11.9 11.5 24 -

Page <7> V1.028/07/23 Thick Film Chip Resistors Newark.com/multicomp-pro Farnell.com/multicomp-pro sg.element14.com/b/multicomp-pro Important Notice : This data sheet and its contents (the “Information”) belong to the members of the AVNET group of companies (the “Group”) or are licensed to it. No licence is granted for the use of it other than for information purposes in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any error in or omission from it or for any use made of it. Users of this data sheet should check for themselves the Information and the suitability of the products for their purpose and not make any assumptions based on information included or omitted. Liability for loss or damage resulting from any reliance on the Information or use of it (including liability resulting from negligence or where the Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group’s liability for death or personal injury resulting from its negligence. Multicomp Pro is the registered trademark of Premier Farnell Limited 2019. Description Part Number Thick Film Chip Resistor, 1R MPP102WF100KT2E Thick Film Chip Resistor, 1.2R MPP102WF120KT2E Thick Film Chip Resistor, 1.5R MPP102WF150KT2E Thick Film Chip Resistor, 1.6R MPP102WF160KT2E Thick Film Chip Resistor, 1.8R MPP102WF180KT2E Thick Film Chip Resistor, 2R MPP102WF200KT2E Thick Film Chip Resistor, 2.7R MPP102WF270KT2E Thick Film Chip Resistor, 3R MPP102WF300KT2E Thick Film Chip Resistor, 3.9R MPP102WF390KT2E Thick Film Chip Resistor, 4.7R MPP102WF470KT2E Thick Film Chip Resistor, 5.1R MPP102WF510KT2E Thick Film Chip Resistor, 5.6R MPP102WF560KT2E Thick Film Chip Resistor, 6.2R MPP102WF620KT2E Thick Film Chip Resistor, 6.8R MPP102WF680KT2E Thick Film Chip Resistor, 7.5R MPP102WF750KT2E Thick Film Chip Resistor, 8.2R MPP102WF820KT2E Thick Film Chip Resistor, 9.1R MPP102WF910KT2E Thick Film Chip Resistor, 10R MPP102WF100JT2E Thick Film Chip Resistor, 12R MPP102WF120JT2E Thick Film Chip Resistor, 13R MPP102WF130JT2E Thick Film Chip Resistor, 16R MPP102WF160JT2E Thick Film Chip Resistor, 20R MPP102WF200JT2E Thick Film Chip Resistor, 33R MPP102WF330JT2E Thick Film Chip Resistor, 43R MPP102WF430JT2E Thick Film Chip Resistor, 62R MPP102WF620JT2E Description Part Number Thick Film Chip Resistor, 75R MPP102WF750JT2E Thick Film Chip Resistor, 100R MPP102WF1000T2E Thick Film Chip Resistor, 110R MPP102WF1100T2E Thick Film Chip Resistor, 120R MPP102WF1200T2E Thick Film Chip Resistor, 160R MPP102WF1600T2E Thick Film Chip Resistor, 220R MPP102WF2200T2E Thick Film Chip Resistor, 300R MPP102WF3000T2E Thick Film Chip Resistor, 470R MPP102WF4700T2E Thick Film Chip Resistor, 620R MPP102WF6200T2E Thick Film Chip Resistor, 680R MPP102WF6800T2E Thick Film Chip Resistor, 750R MPP102WF7500T2E Thick Film Chip Resistor, 910R MPP102WF9100T2E Thick Film Chip Resistor, 1.2K MPP102WF1201T2E Thick Film Chip Resistor, 1.5K MPP102WF1501T2E Thick Film Chip Resistor, 3.6K MPP102WF3601T2E Thick Film Chip Resistor, 12K MPP102WF1202T2E Thick Film Chip Resistor, 43K MPP102WF4302T2E Thick Film Chip Resistor, 62K MPP102WF6202T2E Thick Film Chip Resistor, 91K MPP102WF9102T2E Thick Film Chip Resistor, 1R MPP102WJ010JT2E Thick Film Chip Resistor, 5.6R MPP102WJ056JT2E Thick Film Chip Resistor, 120R MPP102WJ0121T2E Thick Film Chip Resistor, 470R MPP102WJ0471T2E Thick Film Chip Resistor, 560R MPP102WJ0561T2E Thick Film Chip Resistor, 1M MPP102WJ0105T2E Part Number Table