MPC15-12 MULTICOMP | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 6

Technical content

Features

  • Ultra-wide voltage input range
  • Low no-load power consumption
  • Protection:Short Circuit/Over Current/Over Voltage
  • Super Small Design
  • Low Ripple & Noise, high efficiency Model Information Part Number DC Voltage Rated Current Rated Power Max. Capacitive Load MPC15-5 5V 3A 15W 5000uF MPC15-12 12V 1.25A 15W 2000uF MPC15-24 24V 0.625A 15W 680uF Voltage Range 85-305V AC, 100-430V DC Frequency Range 47-63Hz Average Efficiency(Typ.) 85% MPC15-5 85% MPC15-12 86% MPC15-24 AC Current (Typ.) 0.45A/115V AC, 0.30A/230V AC Inrush Current(Typ.) Cold Start 30A/115V AC Cold Start 60A/230V AC Leakage Current <0.1mA/277V AC, 50Hz Input

Page <2> V1.010/04/25 PCB Mount Power Supply AC To DC Newark.com/multicomp-pro Farnell.com/multicomp-pro sg.element14.com/b/multicomp-pro Output Ripple & Nose(max.) 70mVp-p All Series Voltage Tolerance ±2.0% All Series Line Regulation ±0.5% All Series Load Regulation ±1.0% All Series No Load Power Consumption(Typ.) 0.1W/230V AC MPC15/5/12 0.12W/230V AC MPC15-24 Setup,Rise Time 1000ms, 30ms/230V AC at full load 1000ms, 30ms/115V AC at full load Hold Up Time (Typ.) 55ms/230V AC at full load 10ms/115V AC at full load Protection Over Current ≥110% Rated Output current Protection type: Shut down O/P voltage, recovers automatically after current goes down Short Circuit Protection type: Hiccup mode, allowing long short circuit mode, re-power on to recover Over Voltage MPC15-5 : ≤7.5V DC MPC15-12 : ≤20V DC MPC15-24 : ≤30V DC Protection type: Output voltage clamp or Hiccup mode Environment Working Temp. -40°C to +85°C (Refer to "Derating Curve") Working Humidity 20 ~ 95% RH Non-Condensing Storage Temp, Humidity -40°C~+85°C,10 ~ 95% RH non-condensing Temp. Coefficient ± 0.02%/°C(0~50°C) MTBF >3200K hrs min. MIL-HDBK-217F (25°C) Projected Lifetime >130Kh/220V AC, 25°C at full load >20Kh/220V AC, 55°C at full load >27Kh/220V AC, 55°C at 80%load Altitude Application 5000m

Page <3> V1.010/04/25 PCB Mount Power Supply AC To DC Newark.com/multicomp-pro Farnell.com/multicomp-pro sg.element14.com/b/multicomp-pro 1. All parameters without special description are measured under the conditions of input 230V AC, rated load, ambient temperature 25°C,and ambient humidity less than 75%. 2. Ripple&noise are measured from peak to peak with band width limit of 20MHz(0.1uf and 47uf /50V parallel capacitor under DC output full load, AC nominal input 25°C ambient temperature). 3. Tolerance :includes set up tolerance, line regulation and load regulation. 4. Derating may be needed under low input voltages. Please check the derating curve for more details. 5. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to”EMI testing of component power supplies.” 6. The ambient temperature derating of 3.5°C/1000m is needed for operating altitude greater than 2000m(6500ft). Physical Property Length × Width × Height 47.4× 26.8 × 23.5mm PCB Mounting Style 76 × 31.5 × 32.3mm Terminal Blocks Style 76 × 31.5 × 36.9mm Din Rail Style Weight 48g(PCB Mounting Style) 88g (Terminal Blocks Style) 88g (Din Rail Style) Cooling Method Natural Air Cooling Texture Black flame retardant and heat resistant plastic Curve

Page <4> V1.010/04/25 PCB Mount Power Supply AC To DC Newark.com/multicomp-pro Farnell.com/multicomp-pro sg.element14.com/b/multicomp-pro Dimensions and Installation Pin-Out Pin Function

1 AC/L

2 AC/N

5 No Pin

annotation: unit of size:mm Pin diameter tolerances:±0.1 [±0.004] General tolerances:±0.5 [±0.02] Pin-Mode Pin Function

1 AC/N

2 AC/L

annotation: unit of size:mm Connection Wire diameter :24-12AWG tightening torque:Max 0.4 N*m Unmarked tolerance:±1 [±0.039] Terminal Blocks Style External Dimension

Page <5> V1.010/04/25 PCB Mount Power Supply AC To DC Newark.com/multicomp-pro Farnell.com/multicomp-pro sg.element14.com/b/multicomp-pro Pin-Mode Pin Function annotation: unit of size:mm Connection Wire diameter :24-12AWG tightening torque:Max 0.4 N.m Unmarked tolerance:±1 [±0.039] Din Rail Style External Dimension Typical application circuit MODEL FUSE R1 C1 C2 TVS MPC15-5 3.15A/300V, Slow fuse, must be connected 6.8Ω/3W(Wire wound resistor, must be connected) 1uF/50V 220uF/16V SMBJ7A MPC15-12 100uF/25V SMBJ20A MPC15-24 100uF/35V SMBJ30A EMC Solution - Recommended circuit Figure 1:Typical application circuit Figure 2:EMC Recommended circuits for higher requirements Component Type Recommended Value MOV 14D561K

Page <6> V1.010/04/25 PCB Mount Power Supply AC To DC Newark.com/multicomp-pro Farnell.com/multicomp-pro sg.element14.com/b/multicomp-pro Important Notice : This data sheet and its contents (the “Information”) belong to the members of the AVNET group of companies (the “Group”) or are licensed to it. No licence is granted for the use of it other than for information purposes in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any error in or omission from it or for any use made of it. Users of this data sheet should check for themselves the Information and the suitability of the products for their purpose and not make any assumptions based on information included or omitted. Liability for loss or damage resulting from any reliance on the Information or use of it (including liability resulting from negligence or where the Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group’s liability for death or personal injury resulting from its negligence. Multicomp Pro is the registered trademark of Premier Farnell Limited 2019. Part Number Table Description Part Number PCB Mount Power Supply, 5V, 3A MPC15-5 PCB Mount Power Supply, 12V, 1.25A MPC15-12 PCB Mount Power Supply, 24V, 0.625A MPC15-24 EMC Solution - Recommended circuit (Recommended when the output end of the product needs to be connected to PE or connected to PE through a Y capacitor Component Type Recommended Value FUSE 3.15A/300V Slow fuse, must be connected MOV 14D561K CX 334K/305VAC R1 12Ω/5W(Winding resistor, must be connected) L1 1.2mH/0.5A CY1/CY2 2.2nF/400VAC GDT 300V/1KA LCM 20mH annotation:Rx1/Rx2/Rx3/Rx4/Rx5/Rx6 is the bleed resistance of CX, the recommended resistance value is 1.5MΩ/150VDC