MPC104AU

MPC104 TI1 | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 16

Technical content

©1994 Burr-Brown Corporation PDS-1230C Printed in U.S.A. July, 1994

FEATURES

l BANDWIDTH: 210MHz (1.4Vp-p) l LOW INTERCHANNEL CROSSTALK: –79dB (30MHz, SO); –77dB (30MHz, DIP) l LOW SWITCHING TRANSIENTS: +13mV/–4mV l LOW DIFFERENTIAL GAIN/PHASE ERRORS: 0.03%, 0.01° l LOW QUIESCENT CURRENT: One Channel Selected: ±4.6mA No Channel Selected: ±120µA

APPLICATIONS

l VIDEO ROUTING AND MULTIPLEXING (CROSSPOINTS) l RADAR SYSTEMS l DATA ACQUISITION l INFORMATION TERMINALS l SATELLITE OR RADIO LINK IF ROUTING The MPC104 consists of two identical monolithic, integrated, open-loop buffer amplifiers, which are connected internally at the output. The bipolar comple- mentary buffers form a unidirectional transmission path and offer extremely high output-to-input isola- tion. The MPC104 multiplexer enables the user to connect one of two input signals to the output. The output of the multiplexer is in a high-impedance state when no channel is selected. When one channel is selected with a digital “1” at the corresponding SEL input, the component acts as a buffer with high input impedance and low output impedance. The wide bandwidth of over 210MHz at 1.4Vp-p signal level, high linearity and low distortion, and low input voltage noise of 5nV/√Hz make this crosspoint switch suitable for RF and video applications. All performance is specified with ±5V supply voltage, which reduces power consumption in comparison with ±15V designs. The multiplexer is available in a space- saving 8-pin SO and DIP packages. Both are designed and specified for operation over the industrial tem- perature range (–40°C to +85°C.) Wide-Bandwidth 2 x 1 VIDEO MULTIPLEXER

DESCRIPTION

The MPC104 is a wide-bandwidth, 2-to-1 channel video signal multiplexer, which can be used in a wide variety of applications. It was designed for wide-bandwidth systems, includ- ing high-definition television and broadcast equip- ment. Although it is primarily used to route video signals, the harmonic and dynamic attributes of the MPC104 also make it appropriate for other analog signal routing applications such as radar, communica- tions, computer graphics, and data acquisition sys- tems. IN1 +1 VOUT SEL 1 IN2 +1 SEL 2 TRUTH TABLE SEL 1 SEL 2 VOUT 0 0 HI-Z 1 0 I N 1 0 1 I N 2 MPC104 International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111 • Twx: 910-952-1111 Internet: http://www.burr-brown.com/ • FAXLine: (800) 548-6133 (US/Canada Only) • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132 MPC104 MPC104 SBFS008

SPECIFICATIONS –DC CHARACTERISTICS At VCC = ±5VDC, RL = 10kΩ , RIN = 100Ω , RSOURCE = 50Ω , and TA = +25°C, unless otherwise noted. The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support devices and/or systems. MPC104AP, AU PARAMETER CONDITIONS MIN TYP MAX UNITS INPUT OFFSET VOLTAGE Initial 14 ±30 mV vs Temperature 60 µV/°C vs Supply (Tracking) V CC = ±4.5V to ±5.5V –40 –80 dB vs Supply (Non-tracking) V CC = +4.5V to +5.5V –50 dB vs Supply (Non-tracking) V CC = –4.5V to –5.5V –50 dB Initial Matching All Buffers 3 mV INPUT BIAS CURRENT Initial 5 ±10 µA vs Temperature 20 nA/ °C vs Supply (Tracking) V CC = ±4.5V to ±5.5V ±710 nA/V vs Supply (Non-tracking) V CC = +4.5V to +5.5V 0.26 µA/V vs Supply (Non-tracking) V CC = –4.5V to –5.5V 1.7 µA/V INPUT IMPEDANCE Resistance Channel On 0.88 M Ω Capacitance Channel On 1.0 pF Capacitance Channel Off 1.0 pF INPUT NOISE Voltage Noise Density f OUT = 20kHz to 10MHz 5 nV/ √Hz Signal-to-Noise Ratio S/N = 0.7/V N • √5MHz 96 dB INPUT VOLTAGE RANGE Gain Error ≤ 10% ±3.6 V TRANSFER CHARACTERISTICS Voltage Gain R L = 1kΩ , VIN = ±2V 0.982 V/V R L = 10kΩ , VIN = ±2.8V 0.98 0.992 V/V RATED OUTPUT Voltage V IN = ±3V ±2.8 ±2.97 V Resistance One Channel Selected 12.5 Ω Resistance No Channel Selected 900 M Ω Capacitance No Channel Selected 1.2 pF CHANNEL SELECTION INPUTS Logic 1 Voltage +2 V CC +0.6 V Logic 0 Voltage +0.8 V Logic 1 Current V SEL = 5.0V 75 100 125 µA Logic 0 Current V SEL = 0.8V 0.002 5 µA SWITCHING CHARACTERISTICS VI = –0.3V to +0.7V, f = 5MHz SEL to Channel ON Time 90% Point of V OUT = 1Vp-p 0.13 µs SEL to Channel OFF Time 10% Point of V OUT = 1Vp-p 0.17 µs Switching Transient, Positive (Measured While Switching +13 mV Switching Transient, Negative Between Two Grounded Channels) –4 mV POWER SUPPLY Rated Voltage ±5V Derated Performance ±4.5 ±5.5 V Quiescent Current One Channel Selected, Over Temperature ±4.6 ±5.3 mA No Channel Selected, Over Temperature ±120 ±175 µA Rejection Ratio –80 dB

SPECIFICATIONS – AC CHARACTERISTICS At VCC = ±5VDC, RL = 10kΩ , RIN = 100Ω , RSOURCE = 50Ω , and TA = +25°C, unless otherwise noted. MPC104AP, AU PARAMETER CONDITIONS MIN TYP MAX UNITS LARGE SIGNAL BANDWIDTH (–3dB) VOUT = 5.0Vp-p, COUT = 1pF 55 MHz VOUT = 2.8Vp-p, COUT = 1pF 101 MHz VOUT = 1.4Vp-p, COUT = 1pF 210 MHz SMALL SIGNAL BANDWIDTH VOUT = 0.2Vp-p, COUT = 1pF 590 MHz GROUP DELAY TIME 550 ps DIFFERENTIAL GAIN f = 4.43MHz, VIN = 0.3Vp-p VDC = 0 to 0.7V 0.03 % DIFFERENTIAL PHASE f = 4.43MHz, VIN = 0.3Vp-p VDC = 0 to 0.7V 0.01 Degrees GAIN FLATNESS PEAKING VOUT = 0.2Vp-p, DC to 30MHz 0.05 dB VOUT = 0.2Vp-p, DC to 100MHz 0.07 dB HARMONIC DISTORTION f = 30MHz, VOUT = 1.4Vp-p Second Harmonic –63 dBc Third Harmonic –65 dBc CROSSTALK VIN = 1.4Vp-p MPC104AP Channel-to-Channel f = 5MHz, –90 dB f = 30MHz, –77 dB Off Isolation f = 5MHz, –93 dB f = 30MHz, –81 dB MPC104AU Channel-to-Channel f = 5MHz, –95 dB f = 30MHz, –79 dB Off Isolation f = 5MHz, –93 dB f = 30MHz –86 dB RISE/FALL TIME VOUT = 1.4Vp-p, Step 10% to 90% C OUT = 1pF, ROUT = 22Ω 2.3 ns SLEW RATE VOUT = 1.4Vp-p C OUT = 1pF 500 V/ µs C OUT = 22pF 360 V/ µs C OUT = 47pF 260 V/ µs

IN1, IN2 Analog Input Channels GND Analog Input Shielding Grounds, Connect to System Ground SEL 1, SEL2 Channel Selection Inputs VOUT Analog Output; tracks selected channel –VCC Negative Supply Voltage; typical –5VDC +VCC Positive Supply Voltage; typical +5VDC CONNECTION DIAGRAM PIN DESCRIPTION Top View DIP/SO-8 ABSOLUTE MAXIMUM RATINGS PACKAGE DRAWING TEMPERATURE PRODUCT PACKAGE NUMBER (1) RANGE MPC104AP 8-Pin Plastic DIP 006 –40 °C to +85°C MPC104AU SO-8 Surface Mount 182 –40 °C to +85°C NOTE: (1) For detailed drawing and dimension table, please see end of data sheet, or Appendix C of Burr-Brown IC Data Book. PACKAGE/ORDERING INFORMATION IN1 GND +V CC IN2 SEL 1 –VCC VOUT SEL 2 ELECTROSTATIC DISCHARGE SENSITIVITY This integrated circuit can be damaged by ESD. Burr-Brown recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degrada- tion to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.

TYPICAL PERFORMANCE CURVES At VCC = ±5VDC, RL = 10kΩ , RIN = 100Ω , RSOURCE = 50Ω , and TA = +25°C, unless otherwise noted. –40 –20 0 20 60 80 100 Temperature (°C) Input Offset Voltage (mV) INPUT OFFSET VOLTAGE vs TEMPERATURE 40 –40 –20 0 20 60 80 100 Temperature (°C) Input Bias Current (µA) INPUT BIAS CURRENT vs TEMPERATURE 10k 100k 1M 10M 100M 1G Frequency (Hz) 100 1.0M 100k 10k Input Impedance (Ω ) INPUT IMPEDANCE vs FREQUENCY 10k 100k 1M 10M 100M 1G Frequency (Hz) 100 Output Impedance (Ω ) OUTPUT IMPEDANCE vs FREQUENCY –40 –20 0 20 60 80 100 Temperature (°C) Supply Current (mA) TOTAL POSITIVE QUIESCENT CURRENT vs TEMPERATURE One Channel Selected –40 –20 0 20 60 80 100 Temperature (°C) 140 120 100 Supply Current (µA) TOTAL POSITIVE QUIESCENT CURRENT vs TEMPERATURE No Channel Selected

Time (µs) SWITCHING TRANSIENTS Time (µs) SWITCHING ENVELOPE (Channel-to-Channel Switching) Time (µs) TYPICAL PERFORMANCE CURVES (CONT) At VCC = ±5VDC, RL = 10kΩ , RIN = 100Ω , RSOURCE = 50Ω , and TA = +25°C, unless otherwise noted. +5V +20mV –5mV SEL 36MHz Low-Pass Filter Acc. Eureka Rec. EU95-PG03 in Signal Path +5V +5mV –5mV DB1VIN SEL 1 DB2 SEL 2 VOUT1 100Ω 100Ω VOUT VOUT +0.7V –0.3V SEL SEL VOUT 36MHz Low Pass Filter Acc. Eureka Rec. EU95-PG03Wideband Measurement Input Voltage (V) Output Voltage (V) TRANSFER FUNCTION – 5 – 4 – 3 – 2 – 1 012345 – 5 – 4 – 3 – 2 – 1 012345 Input Voltage (V) Gain Error (%) GAIN ERROR vs INPUT VOLTAGE +25°C –40°C +85°C 10 100 10k 100k 1M 10M Frequency (Hz) 100 Voltage Noise (nV/ Hz) INPUT VOLTAGE NOISE SPECTRAL DENSITY

TYPICAL PERFORMANCE CURVES (CONT) At VCC = ±5VDC, RL = 10kΩ , RIN = 100Ω , RSOURCE = 50Ω , and TA = +25°C, unless otherwise noted. 0 2 04 06 08 0 1 0 0 Time (ns) VIN = 0.2Vp-p, COUT = 1pF tRISE = tFALL = 2ns (Generator) 150 100 –50 –100 –150 Output Voltage (mV) SMALL SIGNAL PULSE RESPONSE 0 2 04 06 08 0 1 0 0 Time (ns) VIN = 0.2Vp-p, COUT = 47pF tRISE = tFALL = 2ns (Generator) 150 100 –50 –100 –150 Output Voltage (mV) SMALL SIGNAL PULSE RESPONSE 0 2 04 06 08 0 1 0 0 Time (ns) VIN = 4Vp-p, COUT = 1pF tRISE = tFALL = 2ns (Generator) Output Voltage (V) LARGE SIGNAL PULSE RESPONSE 0 2 04 06 08 0 1 0 0 Time (ns) VIN = 4Vp-p, COUT = 47pF tRISE = tFALL = 2ns (Generator) Output Voltage (V) LARGE SIGNAL PULSE RESPONSE GROUP DELAY TIME vs FREQUENCY Frequency (Hz) 1M 10M 100M 1G Delay Time (ns) DUT 100Ω 22Ω 180Ω VOUTVIN 50Ω 1pF BUF601 VIN = 1.4Vp-p –10 –15 –20 –25 Frequency (Hz) Output (dB) 1M 10M 100M 1G BANDWIDTH vs C OUT WITH RECOMMENDED R OUT 1pF 10pF 22pF 33pF 47pF R OUT 1pF 0 Ω 571MHz f–3dBC OUT 10pF 27 Ω 364MHz 22pF 33pF 47pF 16Ω 12Ω 279MHz 231MHz 188MHz

TYPICAL PERFORMANCE CURVES (CONT) At VCC = ±5VDC, RL = 10kΩ , RIN = 100Ω , RSOURCE = 50Ω , and TA = +25°C, unless otherwise noted. –0.7V +0.7V ON/OFF CHARACTERISTIC Time (µs) SEL VOUT +5V GAIN FLATNESS Frequency (Hz) Output (dB) 1M 10M 100M 1G VOUT = 1.4Vp-p VOUT = 0.2Vp-p –10 –20 –30 –40 Output (dBm) BANDWIDTH vs OUTPUT VOLTAGE Frequency (Hz) 1M 10M 100M 1G 5Vp-p 1.4Vp-p 0.2Vp-p 2.8Vp-p Output (dB) BANDWIDTH vs R LOAD Frequency (Hz) 10M 100M 1G1M –10 –20 –30 –40 VOUT = 1.4Vp-p, COUT = 22pF R L = 10kΩ R L = 500Ω –10 –20 –30 Output (dB) BANDWIDTH MATCHING C OUT = 22pF, VOUT = 2.8Vp-p Frequency (Hz) 1M 10M 100M 1G Ch1, Ch2 30M 60M 90M 30MHz HARMONIC DISTORITION Frequency (Hz) VOUT = 1.4Vp-p, RL = 10kΩ , COUT = 1pF –20 –40 –60 –80 Harmonic Distortion (dBc) DUT 100Ω 180Ω 47Ω Advantest R3361A 50Ω BUF601AUHP8116A VIN = 1.4Vp-p G 10kΩ DB1VIN SEL 1 SEL 2 DB2 VOUT 100Ω 100Ω

are unlikely to cause permanent damage. ited to 10mA whenever possible. recommended when handling the MPC104. input channels is typically less than 300ns. FIGURE 1. Internal ESD Protection. internally connected to all pins. multichannel switch matrices. multiplexer, in effect, a quad switchable high-speed buffer. low-impedance transmission lines or inputs. the luminance signal is ramped through its specified range. ance remains high and constant between ON and OFF states. the overall system bandwidth.

glitches in subsequent equipment. shorter than the typical SEL-to-channel-OFF time of 250ns. sign, and results in cooler, more reliable operation. following tips are offered as suggestions, not as absolutes. high-speed components when they are used incorrectly.

• Bypass power supplies very close to the device pins. Use tantalum chip capacitors (approximately 2.2µF), a parallel 470pF ceramic chip capacitor may be added if desired. Surface-mount types are recommended due to their low lead inductance.
• PC board traces for signal and power lines should be wide to reduce impedance or inductance.
• Make short and low inductance traces. The entire physical circuit should be as small as possible.
• Use a low-impedance ground plane on the component side to ensure that low-impedance ground is available through- out the layout. Grounded traces between the input traces are essential to achieve high interchannel crosstalk rejec- tion.
• Do not extend the ground plane under high-impedance nodes sensitive to stray capacitances, such as the buffer’s input terminals.
• Sockets are not recommended, because they add signifi- cant inductance and parasitic capacitance. If sockets must be used, consider using zero-profile solderless sockets.
• Use low-inductance and surface-mounted components. Circuits using all surface mount components with the MPC104 will offer the best AC-performance.
• A resistor (100Ω to 150Ω ) in series with the input of the buffers may help to reduce peaking. Place the resistor as close as possible to the pin.
• Plug-in prototype boards and wire-wrap boards will not function well. A clean layout using RF techniques is essential—there are no shortcuts.

FIGURE 2. Simplified Circuit Diagram.

FIGURE 13. Input Multiplexer for a CRT Output Stage. NOTE: (1) Philips Semiconductors.

FIGURE 14. Input Multiplexer for RGB Video Signals.

Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. Customers are responsible for their applications using TI components. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright  2000, Texas Instruments Incorporated