MPB125

MPB125 POWER-ONE | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 4

Technical content

DESCRIPTION

The MPB125 series incorporates patented high efficiency circuitry, high power density and active Power Factor Correction (PFC) to meet the requirements of networking and data communications systems, as well as commercial and industrial configurations. Dual output units deliver a regulated main output plus a second 12V output for fans or other system functions. Multiple output models provide tightly regulated DC power in a variety of configurations. The MPB125 is rated for convection as well as forced-air cooling. Full output power is available with as few as 130 Linear Feet per Minute (LFM) forced-air cooling. The MPB125 product line is approved to the latest international regulatory standards, and displays the CE Mark.

• High Power Density in Industry Standard 3" x 5" Footprint  Power Factor Correction (PFC) Meets EN61000-3-2  Main Output Remote Sense  Power Good Signals  CE Marked to Low Voltage Directive  Input Transient & ESD Compliance to

FEATURES

MULTIPLE OUTPUT MODEL SELECTION CHART -

80 Watts Convection Cooling, 125 Watts Forced-Air Cooling

OUTPUT MAXIMUM OUTPUT TOTAL RIPPLE & NOISE REGULATION RANGEVOLTAGE CURRENT (AMPS), REGULATION % pk-pk (VOLTS) 130 LFM (NOTE 2) % (NOTE 3) MPB125-2005 +5V 25A ±3% 1% 4.85V to 5.15V +12V 0.5A ±5% 1% 11.40V to 12.60V MPB125-2012 +12V 10.5A ±3% 1% 11.64V to 12.36V +12V 0.5A ±5% 1% 11.40V to 12.60V MPB125-2015 +15V 8.3A ±3% 1% 14.54V to 15.45V +12V 0.5A ±5% 1% 11.40V to 12.60V MPB125-2024 +24V 5.2A ±3% 1% 23.28V to 24.72V +12V 0.5A ±5% 1% 11.40V to 12.60V MPB125-2048 +48V 2.6A ±3% 1% 46.56V to 49.44V +12V 0.5A ±5% 1% 11.40V to 12.60V MPB125-3000 +5V 15A ±3% 1% 4.85V to 5.15V +12V 5A ±5% 1% 11.40V to 12.60V MPB125-4250 +2.5V 10A (NOTE 4,5) ±3% 1% 2.42V to 2.58V +5V 15A (NOTE 4,5) ±3% 1% 4.85V to 5.15V (NOTE 1) +12V 5A ±5% 1% 11.40V to 12.60V MPB125-4350 +3.3V 10A (NOTE 4,5) ±3% 1% 3.20V to 3.40V +5V 15A (NOTE 4,5) ±3% 1% 4.85V to 5.15V (NOTE 1) +12V 5A ±5% 1% 11.40V to 12.60V NOTES: 1) Maximum convection output power is 75 watts. 2) Maximum forced-air output power is 125 watts with 130 LFM at 5 CFM. 3) Maximum peak-to-peak noise expressed as a percentage of output voltage, 20 MHz bandwidth. 4) Maximum power of 80 watts from V1 + V2 with 130 LFM at 5 CFM forced-air cooling. 5) Maximum power of 45 watts from V1 + V2 for convection cooling. NUCLEAR AND MEDICAL APPLICATIONS Power-One products are not authorized for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the President of Po wer-One, Inc. TECHNICAL REVISIONS The appearance of products, including safety agency certifications pictured on labels, may change dependin g on the date manufactured. Specifications are subject to change without notice. Advanced Product Release REV. 08/23/01

PARAMETER CONDITIONS/DESCRIPTION MIN NOM MAX UNITS Input Voltage- AC Continuous input range. 90 264 VAC Input Frequency AC Input. 47 63 Hz Brownout Protection Lowest AC input voltage that regulation is maintained with full rated loads. 90 VAC Hold-up Time Over full AC input voltage range at full rated load. 17 mS Input Current 90 VAC at full rated load. 1.8 A RMS Input Protection Non-user serviceable internally located AC input line fuse, 3.15A. Inrush Surge Current Internally limited by thermistor, 110VAC: 23 APK one cycle, 25° C. 220VAC: 46 Power Factor Circuitry Active PFC meets requirements of EN61000-3-2. Operating Frequency Switching frequency of main transformer. 100 kHz OUTPUT SPECIFICATIONS PARAMETER CONDITIONS/DESCRIPTION MIN NOM MAX UNITS Efficiency Full Load, 230VAC. Varies with distribution of loads among outputs. 75 85 % Minimum Loads V1 + V2 + V3. 5 Watts Ripple and Noise Full load, 20 MHz bandwidth. See Model Selection Chart Output Power 130 LFM at 5 CFM forced-air cooling. 125 WattsConvection, dual and triple-output models. 80 Convection, four-output models. 75 Overshoot /Undershoot Output voltage overshoot/undershoot at turn-on. 10 % Regulation Varies by output. Total regulation includes: line changes from 85-132 VAC See Model Selection Chart or 170-264 VAC, changes in load starting at 20% load and changing to 100% load. Transient Response Maximum deviation due to a 25% load change with unit at 75% load. 3 % Turn-on Delay Time required for initial output voltage stabilization. 0.2 1.5 Sec Turn-on Rise Time Time required for output voltage to rise from 10% to 90%. 0.2 20 mS INTERFACE SIGNALS AND INTERNAL PROTECTION PARAMETER CONDITIONS/DESCRIPTION MIN NOM MAX UNITS Overvoltage Protection V1 of dual and triple output models; V1 & V2 outputs of 4-output models. MPB125-4250 (V1) 3.20 4.0 MPB125-4350 (V1) 3.67 4.8 VDC MPB125-2005, MPB125-3000, MPB125-4X50 5.74 7.0 MPB125-2012 13.5 15.5 MPB125-2015 17.0 19.0 MPB125-2024 27.0 30.7 MPB125-2048 50.0 70.0 Overload Protection Fully protected against output short circuit. Automatic recovery upon removal of overload condition. Remote Sense (Note 1) Total voltage compensation for cable losses on +Sense. 200 mVTotal voltage compensation for cable losses on -Sense. 100 Power Good, Delay High TTL compatible signal is high if output is within 97% of nominal. 100 500 mS Delay after outputs have reached 97%. Power Good, AC Fail TTL compatible signal is low if AC power is interrupted for 16 mS. Power 1.0 mS warning before outputs reach 97% of nominal. NOTES: 1) -Sense must be connected to output common or load common for proper power supply operation. SAFETY, REGULATORY, AND EMI SPECIFICATIONS PARAMETER CONDITIONS/DESCRIPTION MIN NOM MAX UNITS Agency Approvals UL1950. CSA 22.2 No. 234/950. Approved EN60950 (TÜV). Dielectric Withstand Voltage AC to chassis. 1500 VAC Input to output. 3000 VDC Electromagnetic Interference EN55022 Conducted. B Class Advanced Product Release

SAFETY, REGULATORY, AND EMI SPECIFICATIONS (CONTINUED) PARAMETER CONDITIONS/DESCRIPTION MIN NOM MAX UNITS Flicker Per EN61000-3-3. Radiated Susceptibility Per EN61000-4-3. EFT/Burst Per EN61000-4-4. Input Transient Protection Per EN61000-4-5. RF Immunity Per EN61000-4-6. Magnetic Fields Per EN61000-4-8. Voltage Dips Per EN61000-4-11. Insulation Resistance Input to output. 10 M /H9024 Leakage Current Per EN60950 (264 VAC) 1.0 mA ENVIRONMENTAL SPECIFICATIONS PARAMETER CONDITIONS/DESCRIPTION MIN NOM MAX UNITS Altitude Operating 10K ASL FeetNon-Operating 50K Operating Temperature At 100% load: 0 50 °C Storage Temperature -40 70 °C Forced-Air Cooling Forced-air cooling of 130 LFM at 5 CFM is required for full output power. Air velocity is measured with power supply mounted on 0.375" (9.5mm) standoffs. Airflow direction is from the input section to the output section. Temperature Coefficient 0°C to 70°C (after 15 minute warm-up). ±0.02 ±0.05 %/°C Relative Humidity Non-Condensing. 5 85 %RH Shock Operating: 11 ±3mS, 3 axes, Half Sine. 15 G Non-operating: 11 ±3mS, 3 axes, Half Sine. 30 Vibration Operating: Random vibration, 5-500 Hz, 10 minutes each axis. 2.4 G RMS Non-Operating: Random vibration, 5-500 Hz, 10 minutes each axis. 4.8 G RMS Advanced Product Release

MPB125 SERIES Advanced Product Release 5.00" (127.0) 4.55" (115.57) 3.00" (76.2) J1- INPUT CONNECTOR MPB125-3000 MPB125-4250 MPB125-4350 J2 - DC OUTPUT CONNECTOR FASTENER CLEARANCE AREA (4 PL) PIN #1 PIN #1 PIN #1 SAFETY GROUND CONNECTION POINT PRINTED CIRCUIT BOARD SCREWS SHOWN FOR REFERENCE ONLY 2.56" (65.02) 1.25" (31.75) 0.19" (4.8) 0.06" (1.5) 1.00" (25.4) Ø 0.16" (4 PL) (4.06) TOP VIEW SIDE VIEW END VIEW J1 - AC I/P CONN. Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Pin 8 Pin 9 Pin 10 Pin 11 Pin 12 Pin 13 Pin 14 -12V +12V N/C N/C N/C RTN RTN RTN RTN RTN +5V +5V +5V +5V -12V +12V +2.5V +2.5V +2.5V RTN RTN RTN RTN RTN +5V +5V +5V +5V -12V +12V +3.3V +3.3V +3.3V RTN RTN RTN RTN RTN +5V +5V +5V +5V Pin 1 -SENSE Pin 2 +SENSE Pin 3 PWR GOOD J2 - J3 - Pin 1 NEUTRAL Pin 2 NO PIN Pin 3 LINE MPB125 -3000 MPB125 -4250 MPB125 -4350 MPB125-2005 J2 - DC OUTPUT CONNECTOR PIN #1 PIN #1 MPB125-2012 MPB125-2015 PIN #1 PIN #1 J2 - DC OUTPUT CONNECTOR MPB125-2024 J2 - DC OUTPUT CONNECTOR PIN #1 PIN #1 MPB125-2048 J2 - DC OUTPUT CONNECTOR PIN #1 PIN #1 MPB125 MPB125 MPB125 MPB125 MPB125 MPB125 -2005 -2012 -2012 -2024 -2048 -3000 -2015 -2015 -4250 -4350 J1 Housing 09-50-8033 09-50-8033 09-50-8033 09-50-8033 09-50-8033 09-50-8033 Pins 08-52-0113 08-52-0113 08-52-0113 08-52-0113 08-52-0113 08-52-0113 J2 Housing 09-50-8103 09-50-8063 09-50-8063 09-50-8043 09-50-8023 09-50-8143 Pins 08-52-0113 08-52-0113 08-52-0113 08-52-0113 08-52-0113 08-52-0113 J3 Housing 22-01-3067 22-01-3067 22-01-3067 22-01-3067 22-01-3067 22-01-3037 Pins 08-50-0114 08-50-0114 08-50-0114 08-50-0114 08-50-0114 08-50-0114 MATING CONNECTORS NOTE: PART NUMBERS ARE MOLEX; EQUIVALENTS ARE ACCEPTABLE.