MP3310N MPS | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 10

Technical content

50V, 1.3A, Step-up White LED Driver with True PWM Dimming MP3310N Rev.1.0 www.MonolithicPower.com 1 12/2/2014 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2014 MPS. All Rights Reserved. The Future of Analog IC Technology

DESCRIPTION

The MP3310N is a monolithic step-up converter designed for driving arrays of WLEDs from a wide input supply range. The MP3310N uses current mode, fixed frequency architecture to regulate the LED current to user programmed value set by an external current setting resistor. The switching frequency is also programmable with an external resistor. The MP3310N features true PWM dimming, which allows the flexible control of the backlighting luminance under wide range of the ambient brightness. The MP3310N is turned off if an over-voltage condition is present due to an open circuit condition. Use one external resistor voltage divider to program OVP threshold. The MP3310N also includes under-voltage lockout, current limiting and thermal overload protection preventing damage in the event of an output overload. The MP3310N is available in small 10-pin QFN 3x3mm package.

FEATURES

  • Internal 0.3 Ω Power MOSFET
  • Wide 4.5V to 25V Operating Input Range
  • Drives up to 12 Series White LEDs
  • Up to 93% Efficiency
  • True PWM Dimming
  • Adjustable Switching Frequency
  • Adjustable Open Load Protection Voltage
  • Internal 1.3A Current Limit
  • UVLO, Thermal Shutdown
  • Available in 3mm x 3mm QFN10 Package

APPLICATIONS

  • LCD Panels
  • Digital Picture Frames
  • Handheld Computers and PDAs
  • Digital Still Cameras
  • Small LCD Displays All MPS parts are lead-free and adhere to the RoHS directive. For MPS green status, please visit MPS website under Quality Assurance. “MPS” and “The Future of Analog IC Technology” are Registered Trademarks of Monolithi c Power Systems, Inc. TYPICAL APPLICATION EFFICIENCY (%) VIN vs. Efficiency 100 4 8 12 16 20 24 VIN(V)

MP3310N—50V, 1.3A, STEP-UP WHITE LED DRIVER WITH TRUE PWM DIMMING MP3310N Rev.1.0 www.MonolithicPower.com 2 12/2/2014 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2014 MPS. All Rights Reserved.

ORDERING INFORMATION

Part Number* Package Top Marking MP3310NGQ QFN-10 (3mm x 3mm) ALB * For Tape & Reel, add suffix –Z (e.g. MP3310NGQ–Z); PACKAGE REFERENCE ABSOLUTE MAXIMUM RATINGS (1) Continuous Power Dissipation (TA = +25°C) (2) Recommended Operating Conditions (3) Thermal Resistance (4) θJA θJC Notes: 1) Exceeding these ratings may damage the device. 2) The maximum allowable power dissipation is a function of the maximum junction temperature T J(MAX), the junction-to- ambient thermal resistance θJA, and the ambient temperature TA. The maximum allowable continuous power dissipation a t any ambient temperature is calculated by PD(MAX)=(TJ(MAX)- TA)/ θJA. Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. Internal thermal shutdown circuitry protects the device from permanent damage. 3) The device is not guaranteed to function outside of its operation conditions. 4) Measured on JESD51-7 4-layer board.

MP3310N—50V, 1.3A, STEP-UP WHITE LED DRIVER WITH TRUE PWM DIMMING MP3310N Rev.1.0 www.MonolithicPower.com 3 12/2/2014 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2014 MPS. All Rights Reserved.

ELECTRICAL CHARACTERISTICS

VIN = 12V, VEN = 5V, TA = +25°C, unless otherwise noted. Parameters Symbol Condition Min Typ Max Units Operating Input Voltage V IN 4.5 25 V Supply Current (Shutdown) I IN SD V EN = 0V 1 µA Supply Current (Quiescent) I IN QS V EN = 5V, VLED = 1V 1 2 mA LDO Output Voltage V CC VEN = 5V, 6V < VIN < 25V, 0 < IVCC < 10mA 4.3 5.0 5.5 V Switching Frequency f SW RFSET = 50kΩ 470 560 650 kHz RFSET Open 0.8 1 1.2 MHz Maximum Duty Cycle D MAX 90 % Under Voltage Lockout IN Under Voltage Lockout V CC UVLO V IN Rising 3.6 3.9 4.2 V Under Voltage Lockout Hysteresis 450 mV Open Load Protection Threshold VOVP VOV Rising 1.18 1.24 1.30 V Hystersis 0.12 Enable & Dimming EN Low Threshold V EN LOW V EN Falling 0.6 V EN High Threshold V EN HIGH V EN Rising 1.6 V EN Disable Timer 10 ms Current Regulation Delay From V EN Rising Edge 2 µs LED Current Regulation LED Current I LED R ISET = 60kΩ 74.1 76.8 79.5 mA LED Regulation Voltage V LED I LED = 80mA 500 mV Output Switch SW On-Resistance R ON 0.3 Ω SW Current Limit Duty Cycle = 90% 1.3 A Thermal Shutdown 150 °C LED Switch (M2, refer block diagram) On Resistance 2 Ω

MP3310N—50V, 1.3A, STEP-UP WHITE LED DRIVER WITH TRUE PWM DIMMING MP3310N Rev.1.0 www.MonolithicPower.com 4 12/2/2014 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2014 MPS. All Rights Reserved. PIN FUNCTIONS Pin # Name Pin Function

1 OVP

Open Load Protection Programming Pin. Connect a resistor divider from output to this pin to program the OVP threshold. When this pin voltage reaches the threshold 1.24V, the switch will be turned off until VOVP decrease and kick the hysteresis. 2 ISET LED Current Set. Tie a current setting resistor from this pin to ground to program the whole LED current. 3 COMP Step-up Converter Compensation Pin. This pin is used to compensate the regulation control loop. Connect a capacitor or a series RC network from COMP to GND.

4 LED

LED Current Input. This pin is the open-drain output of an internal dimming control switch. Connect the LED cathode to this pin. With internal 500mV reference, the current flows into LED pin should be less than 120mA for normal operation.

5 GND,

Exposed Pad Ground. Connect exposed pad to GND plane for proper thermal performance. 6 SW Power Switch Output. SW is the drain of the internal MOSFET switch. Connect the power inductor and output rectifier to SW. 7 EN/DIM ON/OFF Control and Dimming Command Input. To use PWM dimming, add a 200Hz to 2kHz square wave signal to this pin. 8 VIN Input Supply Pin. Must be locally bypassed.

9 VCC

The Internal 5V Linear Regulator Output. VCC provides power supply for the internal MOSFET switch gate driver and the internal control circuitry. Bypass VCC to GND with a ceramic capacitor. If VIN is less than 5.5V, apply an external 5V supply directly on VCC. 10 FSET Switching Frequency Programming Pin. Connect a resistor to ground to set the switching frequency.

MP3310N—50V, 1.3A, STEP-UP WHITE LED DRIVER WITH TRUE PWM DIMMING MP3310N Rev.1.0 www.MonolithicPower.com 5 12/2/2014 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2014 MPS. All Rights Reserved. TYPICAL PERFORMANCE CHARACTERISTICS VIN = 12V, VEN = 5V, ILED = 80mA, 10WLEDs 4Strings, unless otherwise noted. 100 4 8 12 16 20 24 0 1 02 03 04 05 06 07 08 09 0 1 0 0 IINDUCTOR 200mA/div. VSW 20V/div. VOUT/AC 200mV/div. VIEST 500mV/div. ILED 50mA/div. VSW 20V/div. VEN 5V/div. VCMOP 500mV/div. ILED 50mA/div. VSW 20V/div. VEN 5V/div. VOUT 10V/div. ILED 50mA/div. VSW 20V/div. PWM 2V/div. VOUT 10V/div. ILED 50mA/div. VSW 20V/div. PWM 2V/div. VOUT 10V/div. 200 300 400 500 600 700 800 900 1000 1100 1200 1300 0 20 40 60 80 100 120

MP3310N—50V, 1.3A, STEP-UP WHITE LED DRIVER WITH TRUE PWM DIMMING MP3310N Rev.1.0 www.MonolithicPower.com 6 12/2/2014 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2014 MPS. All Rights Reserved. FUNCTION DIAGRAM Figure 1—MP3310N Function Block Diagram

MP3310N—50V, 1.3A, STEP-UP WHITE LED DRIVER WITH TRUE PWM DIMMING MP3310N Rev.1.0 www.MonolithicPower.com 7 12/2/2014 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2014 MPS. All Rights Reserved. OPERATION The MP3310N employs a constant frequency, peak current mode step-up converter and internal regulated current source to regulate the array of white LEDs. The operation of the MP3310N can be understood by referring to the block diagram of Figure 1. Internal 5V Regulator The MP3310N includes an internal linear regulator (VCC). When VIN is greater than 5.5V, this regulator offers a 5V power supply for the internal MOSFET switch gate driver and the internal control circuitry. The VCC voltage drops to 0V when the chip shuts down. In the application of VIN smaller than 5.5V, tie VCC and VIN together. The MP3310N features Under Voltage Lockout. The chip is disabled until VCC exceeds the UVLO threshold. And the hysteresis of UVLO is approximately 450mV. System Startup When the MP 3310N is enabled and VCC exceeds the UVLO threshold, the capacitor on COMP pin is charged. Once the COMP level reaches to about 750mV, the switching begins and the MP3310N starts boosting the step-up converter. Step-up Converter The converter operation frequency is adjustable by FSET setting resistor, which is helpful for optimizing the external components sizes and improving the efficiency. At the beginning of each cycle, the power FET is turned on with the internal clock. To prevent sub- harmonic oscillations at duty cycles greater than 50 percent, a stabilizing ramp is added to the output of the current sense amplifier and the result is fed into the PWM comparator. When this result voltage reaches the output voltage of the error amplifier (V COMP) the power FET is turned off. The COMP voltage at the output of the internal error amplifier is an amplified signal of the difference between the 500mV reference voltage and the feedback voltage. The converter automatically provides enough bus voltage to power the LED array. If the feedback voltage drops below the 500mV reference, the output of the error amplifier increases. It results in more current flowing through the power FET, thus increasing the power delivered to the output. In this way it forms a close loop to make the LED current in regulation. At light-load or VOUT near to VIN operation, the converter runs into the pulse-skipping mode, the FET is turned on for a minimum on-time, and then the converter discharges the power to the output in the remnant period. The FET will keep off until the output voltage needs to be boosted again. Dimming Control The MP3310N incorporates both Enable and PWM dimming onto a single control pin. The part features true PWM dimming which results in PWM chopping of the current in the LEDs to provide flexible LED brightness control. Open Load Protection The open load protection is achieved through the over voltage protection. If LED array is open, the LED pin is pulled to ground and the IC keeps charging the output voltage until it reach OVP threshold. Then MP3310 turns off the internal switch and recovers when V OVP falls to hysteresis.

MP3310N—50V, 1.3A, STEP-UP WHITE LED DRIVER WITH TRUE PWM DIMMING MP3310N Rev.1.0 www.MonolithicPower.com 8 12/2/2014 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2014 MPS. All Rights Reserved.

APPLICATION INFORMATION

Setting the Switching Frequency The resistor on FSET pin is used to set the switching frequency. The relationship of the operating frequency vs. the FSET resistor is showed as the curve in page 5. A 20kΩ to 100kΩ FSET resistor, which sets the operating frequency from around 1.2MHz to 300kHz, is recommended. Leaving the FSET pin open sets the switching frequency to 1MHz as default. Setting the LED Current The regulated total LED current is identical and set through the current setting resistor on the ISET pin through the use of the equation: I LED = 4605V / RISET For RISET=60.4kΩ, the LED current is set to about 76.2mA. The ISET pin can not be open. With internal 500mV reference, the current flows into LED pin should be less than 120mA for normal operation. PWM Dimming Apply a 200Hz to 2kHz square waveform to the EN pin to implement PWM dimming of the LEDs. The minimum recommended amplitude of the PWM signal is 2V. Setting the Over Voltage Protection The open load protection is achieved through the over voltage protection (OVP) setting. In some cases, LED strings failure results in the feedback voltage is always zero. The part then keeps boosting the output voltage higher and higher. If the output voltage reaches the programmable OVP threshold, the protection will be triggered. To make sure the chip functions properly in normal operation, the OVP setting resistor divider must be set with a proper value. The recommended OVP point is about 1.3 times higher than the output voltage for normal operation. V OV=1.24V x (R1+R2)/R2 Selecting the Inductor A 10μH to 22µH inductor with a DC current rating of at least 40% higher than the maximum input current is recommended for most applications at wide input range. For highest efficiency, the inductor’s DC resistance should be as small as possible. Selecting the Input Capacitor The input capacitor reduces the surge current drawn from the input supply and the switching noise from the device. The input capacitor impedance at the switching frequency should be less than the input source impedance to prevent high frequency switching current from passing through the input. Ceramic capacitors with X5R or X7R dielectrics are highly recommended because of their low ESR and small temperature coefficients. For most applications, two 4.7 μF capacitors paralleled is sufficient. Selecting the Output Capacitor The output capacitor keeps the output voltage ripple small and ensures feedback loop stability. The output capacitor impedance should be low at the switching frequency. Ceramic capacitors with X7R dielectrics are recommended for their low ESR characteristics. For most applications, a 1μF ceramic capacitor is sufficient. Layout Considerations Careful attention must be paid to the PCB board layout and components placement. Proper layout of the high frequency switching path is critical to prevent noise and electromagnetic interference problems. The loop of MP3310N SW to GND pin, output diode, and output capacitor is flowing with high frequency pulse current. It must be as short as possible. The IC exposed pad is internally connected to GND pin. Lay the GND plane widely for proper thermal performance. The VCC pin is the power supply input for the internal MOSFET switch gate driver and the internal control circuitry. It must be locally bypassed.

MP3310N—50V, 1.3A, STEP-UP WHITE LED DRIVER WITH TRUE PWM DIMMING NOTICE: The information in this document is subject to change without notice. Users should warrant and guarantee that third party Intellectual Property rights are not infringed upon w hen integrating MPS products into any application. MPS will not assume any legal responsibility for any said applications. MP3310N Rev. 1.0 www.MonolithicPower.com 10 12/2/2014 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2014 MPS. All Rights Reserved.

PACKAGE INFORMATION

QFN-10 (3mm x 3mm) SIDE VIEW TOP VIEW 110 6 5 BOTTOM VIEW 2.90 3.10 1.45 1.752.90 3.10 2.25 2.55 0.50 BSC 0.18 0.30 0.80 1.00 0.00 0.05

0.20 REF

1.70 0.50 0.25 RECOMMENDED LAND PATTERN

2.90 NOTE:

1) ALL DIMENSIONS ARE IN MILLIMETERS. 2) EXPOSED PADDLE SIZE DOES NOT INCLUDE MOLD FLASH. 3) LEAD COPLANARITY SHALL BE 0.10 MILLIMETER MAX. 4) DRAWING CONFORMS TO JEDEC MO-229, VARIATION VEED-5. 5) DRAWING IS NOT TO SCALE. PIN 1 ID SEE DETAIL A 2.50 0.70 PIN 1 ID OPTION B R0.20 TYP. PIN 1 ID OPTION A R0.20 TYP. DETAIL A 0.30 0.50PIN 1 ID INDEX AREA