MP3217 MPS | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 10

Technical content

36V, 670kHz Step-up Converter with a 0.5A Switch MP3217 Rev. 0.91 www.MonolithicPower.com 1 10/15/2009 MPS Proprietary Information. Unaut horized Photocopy and Duplication Prohibited. © 2009 MPS. All Rights Reserved. The Future of Analog IC Technology

DESCRIPTION

The MP3217 is a monolithic step up converter integrating a 0.5A, 0.6 Ω internal switch. The MP3217 uses current mode, fixed frequency architecture to regulate the output voltage, providing fast transient response and cycle by cycle current limit. The MP3217 includes under-voltage lockout, over voltage protection and thermal overload protection preventing damage in the event of an output overload. The MP3217 is available in small 6-pin TSOT23 package.

FEATURES

  • Internal 0.6 Ω Power MOSFET
  • Up to 36V Output Voltage
  • 670kHz Fixed Switching Frequency
  • 42V Over Voltage Shutdown
  • Cycle-by-Cycle Over Current Protection
  • UVLO, Thermal Shutdown
  • Available in TSOT23-6 Packages

APPLICATIONS

  • APD Bias Generation
  • Portable Applications
  • Handheld Computers and PDAs
  • Digital Still Cameras “Monolithic Power Systems”, “MPS”, and “The Future of Analog IC Technology” are Registered Trademarks of Monolithic Power Systems, Inc. TYPICAL APPLICATION MP3217 VIN=5V B0540 ENABLE IN SW EN GND FB VOUT=33V PGND 40 0 2 4 6 8 1 01 21 41 61 82 0 OUTPUT CURRENT (mA) Efficiency vs. Output Current EFFICIENCY (%)

MP3217 –36V, 670kHz STEP-UP CONVERTER WITH A 0.5A SWITCH MP3217 Rev. 0.91 www.MonolithicPower.com 2 10/15/2009 MPS Proprietary Information. Unaut horized Photocopy and Duplication Prohibited. © 2009 MPS. All Rights Reserved.

ORDERING INFORMATION

  • For Tape & Reel, add suffix –Z (e.g. MP3217DJ–Z); For RoHS Compliant Packaging, add suffix –LF (e.g. MP3217DJ–LF–Z) PACKAGE REFERENCE PGND GND FB SW IN EN TOP VIEW ABSOLUTE MAXIMUM RATINGS (1) Continuous Power Dissipation (TA = +25°C) (2) Recommended Operating Conditions (3) Thermal Resistance (4) θJA θJC Notes: 1) Exceeding these ratings may damage the device. 2) The maximum allowable power dissipation is a function of the maximum junction temperature T J(MAX), the junction-to- ambient thermal resistance θJA, and the ambient temperature TA. The maximum allowable continuous power dissipation at any ambient temperature is calculated by PD(MAX)=(TJ(MAX)- TA)/θJA. Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. Internal thermal shutdown circuitry protects the device from permanent damage. 3) The device is not guaranteed to function outside of its operating conditions. 4) Measured on JESD51-7, 4-layer PCB. Part Number* Package Top Marking Temperature MP3217DJ TSOT23-6 7H -40°C to +85°C

MP3217 –36V, 670kHz STEP-UP CONVERTER WITH A 0.5A SWITCH MP3217 Rev. 0.91 www.MonolithicPower.com 3 10/15/2009 MPS Proprietary Information. Unaut horized Photocopy and Duplication Prohibited. © 2009 MPS. All Rights Reserved.

ELECTRICAL CHARACTERISTICS

VIN = VEN = 5V, TA = +25°C, unless otherwise noted. Parameters Symbol Condition Min Typ Max Units Operating Input Voltage V IN 2.5 6 V Supply Current (Shutdown) V EN = 0V 10 µA Supply Current (Quiescent) V FB = 0.15V 460 560 µA Switching Frequency f SW 570 670 770 kHz Maximum Duty Cycle V FB = 0V 92 % Under Voltage Lockout IN Under Voltage Lockout UVLO V IN Rising 2.25 2.45 V Under Voltage Lockout Hysteresis 92 mV Over Voltage Shutdown Threshold VOV V OV Rising 42 V Enable EN OFF Threshold V EN Falling 0.8 V EN ON Threshold V EN Rising 2 V Feedback FB Voltage V FB 1.20 1.24 1.28 V FB Input Bias Current V FB = 1.2V -100 nA Output Switch SW On-Resistance (5) R ON 0.6 Ω SW Current Limit (5) Duty Cycle = 60% 0.50 A Thermal Shutdown (5) 150 °C Notes: 5) Guaranteed by design.

MP3217 –36V, 670kHz STEP-UP CONVERTER WITH A 0.5A SWITCH MP3217 Rev. 0.91 www.MonolithicPower.com 4 10/15/2009 MPS Proprietary Information. Unaut horized Photocopy and Duplication Prohibited. © 2009 MPS. All Rights Reserved. PIN FUNCTIONS Pin # Name Pin Function 1 PGND Power Ground. 2 GND Ground. 3 FB Feedback Input. Reference voltage is 1.24V, Connect a resistor divider from the output to this pin. 4 EN ON/OFF Control Input. A voltage greater than 2V will turn the part on and less than 0.8V will turn the part off. When not used, fl oat EN to the input source for automatic startup. 5 IN Input Supply Pin. Must be locally bypassed. 6 SW Power Switch Output. SW is the drain of the internal MOSFET switch. Connect the power inductor and output rectifier to SW.

MP3217 –36V, 670kHz STEP-UP CONVERTER WITH A 0.5A SWITCH MP3217 Rev. 0.91 www.MonolithicPower.com 5 10/15/2009 MPS Proprietary Information. Unaut horized Photocopy and Duplication Prohibited. © 2009 MPS. All Rights Reserved. TYPICAL PERFORMANCE CHARACTERISTICS Circuit refer to Figure 2, VIN=5V, VOUT=33V, TA=+25˚C, unless otherwise noted. 0 2 4 6 8 1 01 21 41 61 82 0 OUTPUT CURRENT (mA) INPUT VOLTAGE (V) OUTPUT CURRENT (mA) Efficiency vs. Output Current Line Regulation IOUT=10mA Load Regulation EFFICIENCY (%) 0 5 10 15 20 25 Current Limit vs. Duty VFB=0V 100 200 300 400 500 600 700 800 900 1000 DUTY (%) CURRENT LIMIT (mA) VOUT/AC 20mV/div VSW 20V/div IINDUCTOR 100mA/div VOUT/AC 50mV/div VSW 20V/div IINDUCTOR 100mA/div 2us/div 2us/div Steady State IOUT=0mA Steady State IOUT=10mA VIN Power On IOUT=10mA VOUT 20V/div VIN 2V/div VSW 20V/div IINDUCTOR 200mA/div 1ms/div LOAD REGULATION(%) -0.30 -0.20 -0.10 0.00 0.10 0.20 0.30 LINE REGULATION (%) VOUT 20V/div VEN 5V/div VSW 20V/div IINDUCTOR 200mA/div 200us/div2ms/div VIN Power Off IOUT=10mA EN Power On IOUT=10mA VOUT 20V/div VIN 2V/div VSW 20V/div IINDUCTOR 200mA/div 10 20 30 40 50 60 70 80 90100 -0.60 -0.40 -0.20 0.00 0.20 0.40 0.60

MP3217 –36V, 670kHz STEP-UP CONVERTER WITH A 0.5A SWITCH MP3217 Rev. 0.91 www.MonolithicPower.com 6 10/15/2009 MPS Proprietary Information. Unaut horized Photocopy and Duplication Prohibited. © 2009 MPS. All Rights Reserved. TYPICAL PERFORMANCE CHARACTERISTICS (continued) Circuit refer to Figure 2, VIN=5V, VOUT=33V, TA=+25˚C, unless otherwise noted. VOUT 20V/div VEN 5V/div VSW 20V/div IINDUCTOR 200mA/div VOUT 20V/div VEN 5V/div VSW 20V/div IINDUCTOR 200mA/div VOUT 20V/div VEN 5V/div VSW 20V/div IINDUCTOR 200mA/div 200us/div100us/div 100us/div EN Power Off IOUT=10mA Over Voltage Protection Start up without R1 Over Voltage Protection Remove R1 at working

MP3217 –36V, 670kHz STEP-UP CONVERTER WITH A 0.5A SWITCH MP3217 Rev. 0.91 www.MonolithicPower.com 7 10/15/2009 MPS Proprietary Information. Unaut horized Photocopy and Duplication Prohibited. © 2009 MPS. All Rights Reserved. OPERATION The MP3217 uses a constant frequency, peak current mode boost regulator architecture to regulate the output voltage. The operation of the MP3217 can be understood by referring to the block diagram of Figure 1. At the start of each oscillator cycle the FET is turned on through the control circuitry. To prevent sub-harmonic oscillations at duty cycles greater than 50 percent, a stabilizing ramp is added to the output of the current sense amplifier and the result is fed into the positive input of the PWM comparator. When this voltage equals the output voltage of the error amplifier the power FET is turned off. The voltage at the output of the error amplifier is an amplified version of the difference between the 1.24V reference voltage and the feedback voltage. In this way the peak current level keeps the output in regulation. If the feedback voltage starts to drop, the output of the error amplifier increases. This results in more current flowing through the power FET, thus increasing the power delivered to the output. Over voltage protection shuts off the MP3217 if the output voltage goes too high. In some cases, loose high side resistor or improper divided resistor; this results in the feedback voltage is always below reference. The part runs at maximum duty cycle boosting the output voltage higher and higher. If the output ever exceeds 42V, the MP3217 shuts down. And It does not switch again until the power is recycled. 670kHz Enable AMPLIFIER PWM COMPARATOR CONTROL LOGIC CURRENT SENSE AMPLIFIER PGND SW GND ENABLE& REFERENCE CONTROL INTERNAL REGULATOR EN FB IN Figure 1—Functional Block Diagram

MP3217 –36V, 670kHz STEP-UP CONVERTER WITH A 0.5A SWITCH MP3217 Rev. 0.91 www.MonolithicPower.com 8 10/15/2009 MPS Proprietary Information. Unaut horized Photocopy and Duplication Prohibited. © 2009 MPS. All Rights Reserved.

APPLICATION INFORMATION

Components referenced below apply to Typical Application Circuit refer to Figure 2. Setting the Output Voltage Set the output voltage by selecting the resistive voltage divider ratio. Use 5.1k Ω for the low-side resistor R2 of the voltage divider. Determine the high-side resistor R1 by the equation: OUT FB FB R2 (V V )R1 V ×−= Where, VOUT is the output voltage, VFB = 1.24V. For R2 = 5.1kΩ and VOUT = 33V, then R1 = 130.6k Ω. There choose a 133k Ω standard 1% value. Selecting the Input Capacitor An input capacitor is required to supply the AC ripple current to the inductor, while limiting noise at the input source. This capacitor must have low ESR, so ceramic is the best choice. Use an input capacitor value of 4.7µF or greater. This capacitor must be placed physically close to the IN pin. Since it reduces the voltage ripple seen at IN, it also reduces the amount of EMI passed back along that line to the other circuitry. Selecting the Output Capacitor The output capacitor is required to maintain the DC output voltage. Low ESR capacitors are preferred to keep the output voltage ripple to a minimum. The characteristic of the output capacitor also affects the stability of the regulation control system. Ceramic, tantalum, or low ESR electrolytic capacitors are recommended. In the case of ceramic capacitors, the impedance of the capacitor at the switching frequency is dominated by the capacitance, and so the output voltage ripple is mostly independent of the ESR. The output voltage ripple is estimated to be: IN LOAD OUT RIPPLE SW V1 - IVV C2 f Where VRIPPLE is the output ripple voltage, VIN and VOUT are the DC input and output voltages respectively, I LOAD is the load current, f SW is the switching frequency, and C2 is the capacitance of the output capacitor. Selecting the Inductor The inductor is required to force the higher output voltage while being driven by the lower input voltage. A larger value inductor results in less ripple current that results in lower peak inductor current, reducing stress on the internal power switch. However, the larger value inductor has a larger physical size, higher series resistance, and/or lower saturation current. Inductance from 2.2µH to 33µH is a good choice for high efficiency and small size. To prevent saturation, use an inductor with a saturation current rating that is higher than the device current limit. Selecting the Diode The output rectifier diode supplies current to the inductor when the internal power MOSFET is off. To reduce losses due to diode forward voltage and recovery time, use a Schottky diode with the MP3217. The diode should be rated for a reverse voltage equal to or greater than the output voltage used. The average current rating must be greater than the maximum load current expected, and the peak current rating must be greater than the peak inductor current. Layout Consideration High frequency switching regulators require very careful layout for stable operation and low noise. All components must be placed as close to the IC as possible. Keep the path between the SW pin, output diode, output capacitor and GND pin extremely short for minimal noise and ringing. The input capacitor must be placed close to the IN pin for best decoupling. All feedback components must be kept close to the FB pin to prevent noise injection on the FB pin trace. The ground return of the input and output capacitors should be tied close to the GND pin. See the MP3217 demo board layout for reference.

MP3217 –36V, 670kHz STEP-UP CONVERTER WITH A 0.5A SWITCH NOTICE: The information in this document is subject to change wi thout notice. Users should warra nt and guarantee that third party Intellectual Property rights are not infringed upon w hen integrating MPS products into any application. MPS will not assume any legal responsibility for any said applications. MP3217 Rev. 0.91 www.MonolithicPower.com 10 10/15/2009 MPS Proprietary Information. Unaut horized Photocopy and Duplication Prohibited. © 2009 MPS. All Rights Reserved.

PACKAGE INFORMATION

0.30 0.50 SEATING PLANE

0.95 BSC

0.84 0.90 1.00 MAX 0.00 0.10 TOP VIEW FRONT VIEW SIDE VIEW RECOMMENDED LAND PATTERN 2.80 3.00 1.50 1.70 2.60 3.00 1 3 0.09 0.20 NOTE: 1) ALL DIMENSIONS ARE IN MILLIMETERS. 2) PACKAGE LENGTH DOES NOT INCLUDE MOLD FLASH, PROTRUSION OR GATE BURR. 3) PACKAGE WIDTH DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. 4) LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.10 MILLIMETERS MAX. 5) DRAWING CONFORMS TO JEDEC MO-193, VARIATION AA. 6) DRAWING IS NOT TO SCALE. 0.30 0.50 0o-8o

0.25 BSC

2.60 TYP 1.20 TYP 0.95 BSC 0.60 TYP SEE DETAIL "A" DETAIL “A”