MP3011 MPS | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 8

Technical content

1x, 1.5x, 2x High Efficiency Charge Pump

2 White LED Driver

MP3011 Rev. 1.1 www.MonolithicPower.com 1 10/31/2005 MPS Proprietary Information. Unaut horized Photocopy and Duplication Prohibited. © 2005 MPS. All Rights Reserved. The Future of Analog IC Technology TM TM

DESCRIPTION

The MP3011 is a fully automatic driver for powering two white LEDs, with up to 4V forward voltage, from a single Li-Ion or three NiMH cells. The driver performs all of the sensing and control to run the LEDs at an optimum charge pump ratio for efficiency without an expensive inductor. The driver allows PWM operation to support brightness control. The tiny 3mm x 3mm QFN16 package and small external capacitors allow for the most compact white LED solution available. EVALUATION BOARD REFERENCE Board Number Dimensions EV3011DQ-00A 2.4” x 1.9” x 0.4”

FEATURES

  • 2% LED Current Matching
  • High Efficiency (>93%)
  • Current Source Outputs
  • No Ballast Resistors Required
  • 1x, 1.5x and 2x Automatic Modes
  • Constant Frequency Operation
  • Automatic LED Detection
  • High and Low Frequency PWM Capability
  • 2.5V to 5.5V Operation
  • Less than 1 µA Leakage during Shutdown
  • Detects Changes in Battery Level
  • No External Schottky Diode Required
  • Soft-Start and Soft Switching Operation

APPLICATIONS

  • Cell Phones
  • PDA or Hand Held Computers
  • White LED Application at 3.6V Supply “MPS” and “The Future of Analog IC Technology” are Trademarks of Monolithic Power Systems, Inc. TYPICAL APPLICATION MP3011 C1A C1B C2A C2B LED1 LED2 BATT EN RADJ GND LEDC GND ENABLE BATT LED2 LED1 MP3011_TAC01 5, 13 3, 10 100 EFFICIENCY (%) SUPPLY VOLTAGE (V) MP3011_EC01 Efficiency vs Supply Voltage VLED = 3.35V @ 40mA ILED=40mA ILED=20mA ILED=10mA

MP3011 – 1X, 1.5X, 2X AUTO-ADJUST CHARGE PUMP 2 WHITE LED DRIVER MP3011 Rev. 1.1 www.MonolithicPower.com 2 10/31/2005 MPS Proprietary Information. Unaut horized Photocopy and Duplication Prohibited. © 2005 MPS. All Rights Reserved. TM PACKAGE REFERENCE Part Number* Package Temperature MP3011DQ QFN16 (3mm x 3mm) –40°C to +125°C * For Tape & Reel, add suffix –Z (eg. MP3011DQ–Z) For Lead Free, add suffix –LF (eg. MP3011DQ–LF–Z) ABSOLUTE MAXIMUM RATINGS (1) Recommended Operating Conditions (2) Thermal Resistance (4) θJA θJC Notes: 1) Exceeding these ratings may damage the device. 2) The device is not guaranteed to function outside of its operating conditions. 3) Ambient Operating Temperature. 4) Measured on approximately 1” square of 1 oz copper.

ELECTRICAL CHARACTERISTICS

VBATT = 5V, TA = +25°C, unless otherwise noted. Parameter Symbol Condition Min Typ Max Units Input Supply Voltage V BATT 2.5 5.5 V VBATT at 1x to 1.5x Mode Switch V BATT 1x-1.5x ILED = 40mA, VBATT Decreasing, VLED = 3.75V @ 40mA 3.9 V VBATT at 1.5x to 2x Mode Switch V BATT 1.5x-2x ILED = 40mA, VBATT Decreasing, VLED = 3.75V @ 40mA 2.9 V VBATT at 2x to 1.5x Mode Switch V BATT 2x-1.5x VBATT Increasing, VLED = 3.75V @ 40mA 3.1 V VBATT at 1.5x to 1x Mode Switch V BATT 1.5x-1x VBATT Increasing, VLED = 3.75V @ 40mA 4.1 V Supply Current I BATT 2 LEDs at 40mA, 2x Mode, VBATT = 2.5V 164 mA Supply Current Shutdown I BATT SHDN V EN = 0V 0.1 1 µA Current Matching (5) I LED MATCH I LED = 40mA 1.5 % Enable Voltage, High V EN (HIGH) 1.5 V Enable Voltage, Low V EN (LOW) 1.0 V Enable Pin Leakage I EN V EN = 5V 0.1 1 µA Charge Pump Frequency F CP V BATT = 3.3V 1.0 1.3 1.6 MHz Time to Standby Mode (6) T OFF Enable Switched Low 30 µs Enable Pin PWM Frequency Limit F HPWM 50 KHz LED Current I LED R SET = 1.54kΩ 40 mA Notes: 5) Matching is defined as the difference of the maximum to minimum current divided by the sum of the maximum and minimum currents. 6) Standby mode switches to shutdown when the output voltage on LEDC drifts back to GND. MP3011_PD01_QFN16 TOP VIEW EXPOSED PAD CONNECT TO PIN 8 PIN 1 ID NC NC GND C1A EN RADJ GND C2B 13141516 8765 LEDCC1BC2ABATT BATTNCLED1LED2

MP3011 – 1X, 1.5X, 2X AUTO-ADJUST CHARGE PUMP 2 WHITE LED DRIVER MP3011 Rev. 1.1 www.MonolithicPower.com 3 10/31/2005 MPS Proprietary Information. Unaut horized Photocopy and Duplication Prohibited. © 2005 MPS. All Rights Reserved. TM TYPICAL PERFORMANCE CHARACTERISTICS VBATT 20mV/div. VLEDC 20mV/div. 400ns/div. MP3011_TPC01 Voltage Ripple in 1.5x Mode 2 x 40mA LEDs VEN 5V/div. IBATT 100mA/div. MP3011_TPC02 Startup in 1.5x Mode 2 x 40mA LEDs (40mA each) VEN 5V/div. IBATT 100mA/div. MP3011_TPC03 Startup in 1x Mode 2 x 40mA LEDs (40mA each) Analog Dimming Circuit of Figure 3, VBATT = 3.6V LED CURRENT (mA) 0123 DC VOLTAGE (V) MP3011_TPC04 LED CURRENT (mA) SUPPLY VOLTAGE (V) MP3011_TPC05 LED Current Matching LED1 LED2

MP3011 – 1X, 1.5X, 2X AUTO-ADJUST CHARGE PUMP 2 WHITE LED DRIVER MP3011 Rev. 1.1 www.MonolithicPower.com 4 10/31/2005 MPS Proprietary Information. Unaut horized Photocopy and Duplication Prohibited. © 2005 MPS. All Rights Reserved. TM PIN FUNCTIONS Pin # Name Description 1, 2, 14 NC No Connect. 3, 10 GND Ground. 4 C1A Charge Pump Capacitor #1 Positive Node. Connect the positive side of the #1 charge pump capacitor to C1A. Typical applications require C1 to be 1µF. 5, 13 BATT Battery Power Input. Connect the 2.5V to 5.5V input source between BATT and GND. Bypass BATT to GND with a 1µF or greater capacitor. 6 C2A Charge Pump Capacitor #2 Positive Node. Connect the positive side of the #2 charge pump capacitor to C2A. Typical applications require C2 to be 1µF. 7 C1B Charge Pump Capacitor #1 Negative Node. Connect the negative side of the #1 charge pump capacitor to C1B.

8 LEDC

LED Common for the Cathodes. Connect the cathodes of the LEDs to LEDC and to a 4.7µF bypass capacitor. Do not connect to any other ground, supply or pin. Note: Exposed pad on backside is connected to this pin. Do Not Ground. 9 C2B Charge Pump Capacitor #2 Negative Node. Connect the negative side of the #2 charge pump capacitor to C2B. 11 RADJ LED Current Adjust Input. Connect a resistor between RADJ and GND to set the LED current. All of the LEDs regulate at the same current. See Setting the LED Current. 12 EN Enable Input. Drive EN high to turn on the MP3011, drive EN low to shutdown the MP3011. To use burst-mode brightness control, drive EN with a PWM signal. See Burst Mode Dimming. 15 LED1 #1 LED Driver. Connect the #1 LED between LED1 and LEDC, with the anode at LED1, and the cathode at LEDC. 16 LED2 #2 LED Driver. Connect the #2 LED between LED2 and LEDC, with the anode at LED2, and the cathode at LEDC.

MP3011 – 1X, 1.5X, 2X AUTO-ADJUST CHARGE PUMP 2 WHITE LED DRIVER MP3011 Rev. 1.1 www.MonolithicPower.com 5 10/31/2005 MPS Proprietary Information. Unaut horized Photocopy and Duplication Prohibited. © 2005 MPS. All Rights Reserved. TM OPERATION The MP3011 is a charge pump that drives 2 LEDs from a 2.5V to 5.5V input voltage. It automatically switches between 1x, 1.5x and 2x charge pump modes to optimize efficiency while maintaining LED current regulation. Two drivers independently regulate the current through the LEDs, therefore matching LEDs are not required. The MP3011 employs soft switching and soft-start to prevent overloading the battery source at turn-on as well as charge pump mode switching. While operating, the MP3011 continually monitors the LED current and battery voltage and automatically switches between charge pump modes to retain LED current regulation through all LEDs as the battery voltage fluctuates. CURRENT GENERATOR CONTROLLER LED ENABLE ISET SHUTDOWN RADJ GND EN BATT 3, 10 5, 13 CHARGE PUMP 1.25V BANDGAP REFERENCE BATTERY SENSOR PUMP MODE SOFT START LED2 LED1 FAULT CURRENT SOURCE FAULT CURRENT SOURCE C2B BATT ENABLE C2A C1B C1A LEDC LED2 LED1 MP3011_F01_BD01 Figure 1—Functional Block Diagram

MP3011 – 1X, 1.5X, 2X AUTO-ADJUST CHARGE PUMP 2 WHITE LED DRIVER MP3011 Rev. 1.1 www.MonolithicPower.com 6 10/31/2005 MPS Proprietary Information. Unaut horized Photocopy and Duplication Prohibited. © 2005 MPS. All Rights Reserved. TM

APPLICATION INFORMATION

When power is applied to the BATT pin, driving EN high will enable the MP3011. The MP3011 begins by checking for open LEDs and determining the optimum charge pump mode. The lowest charge pump mode that allows the programmed LED current in all LEDs is set. This will occur during initial turn-on or during analog mode and burst mode dimming. Shutdown Driving EN low for more than 30µs will disable the MP3011. For safety the MP3011 runs a small supervisory circuit in standby to protect the charge pump output LEDC. The circuit shuts down when the charge pump output returns to zero volts (this can take a few seconds). The MP3011 is in true shutdown mode when LEDC is zero and the 30µs time interval has passed. The supply current should be less than 1µA. Setting the LED Current The LED regulation current is set through the resistor R1 (refer to the typical application circuit on page 1). The voltage across R1 is fixed at 1.25V, and the current through that resistor sets the current through the LEDs. Figure 2 shows LED Current (I LED) vs. R1 with VBATT = 3.6V. LED CURRENT (mA) 0 5 10 15 20 MP3011_F02 Figure 2—I LED vs. R1 Choose R1 for the desired LED current according to the equation: LEDI

62.5 R1=

Where R1 is in k Ω and I LED is in mA. Suitable values for R1 are greater than 1.2kΩ. Soft-Start During startup and mode switching, an internal soft-start prevents excessive input current, preventing excessive loadi ng of the battery or input power source. Burst Mode Dimming To dim the part using burst mode, drive EN with a PWM signal. Each time EN is driven high, the MP3011 goes through the initial startup routine and checks for open LEDs, and the charge pump step-up mode is reset. When EN goes low, the LED current immediately goes to zero. After EN is held low for 30µs or longer, and LEDC falls below GND, the MP3011 operating current drops below 1µA to improve battery life. Maintain the frequency of the PWM signal between 50Hz and 50KHz. Going above 50KHz, the accuracy of the PWM signal will be degraded due to the startup time, and below 50Hz, the LED flicker will be evident to the eye. Ideally, the LED current increases proportionally with the duty cycle of the PWM signal and is independent of the dimming frequency. Analog Mode Dimming Analog dimming can be accomplished with the circuit in Figure 3. The circuit provides 2mA to 30mA dimming with V DC = 0V to 3V. The minimum LED current the MP3011 can regulate is approximately 2mA. LEDC Do not drive or force LEDC as it may be shorted to ground or may be pumped down by the controller in the MP3011 at any time. Excessive capacitance on the LEDC node can cause the internal controller to time out before the charge pump can be ready. Missing the timeouts will cause excessive pumping and a loss of efficiency. The MP3011 requires C1 and C2 be of the same value and type.

MP3011 – 1X, 1.5X, 2X AUTO-ADJUST CHARGE PUMP 2 WHITE LED DRIVER NOTICE: The information in this document is subject to change wi thout notice. Please contact MPS for current specifications. Users should warrant and guarantee that third party Intellectual Property rights ar e not infringed upon when integrating MPS products into any application. MPS will not assume any legal responsibility for any said applications. MP3011 Rev. 1.1 www.MonolithicPower.com 8 10/31/2005 MPS Proprietary Information. Unaut horized Photocopy and Duplication Prohibited. © 2005 MPS. All Rights Reserved. TM

PACKAGE INFORMATION

QFN16 (3mm x 3mm) SIDE VIEW TOP VIEW 1613 8 5 BOTTOM VIEW 2.90 3.10 1.50 1.80 2.90 3.10 1.50 1.80 0.50 BSC 0.18 0.30 0.80 1.00 0.00 0.05

0.20 REF

1.70 0.50 0.25 RECOMMENDED LAND PATTERN

2.90 NOTE:

1) ALL DIMENSIONS ARE IN MILLIMETERS. 2) EXPOSED PADDLE SIZE DOES NOT INCLUDE MOLD FLASH. 3) LEAD COPLANARITY SHALL BE 0.10 MILLIMETER MAX. 4) DRAWING CONFORMS TO JEDEC MO-220, VARIATION VEED-4. 5) DRAWING IS NOT TO SCALE. PIN 1 ID SEE DETAIL A PIN 1 ID OPTION A 0.30x45º TYP. PIN 1 ID OPTION B R0.20 TYP. DETAIL A PIN 1 ID INDEX AREA 0.70 0.30 0.50