MP1L00501035ST ETC2 | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

Features

  • Contactless Linear Sensor - IP64 Debris Proof, Splash Proof - Ideal for Hydraulic and Pneumatic Position Sensing - Liquid Level Capability - Upon request - Male or Female Nicomatic Connectors - Corresponding Exterior Magnet spectrasymbol.com (888) 795-2283Rev G1 - Page 1 Mechanical Specifications Environmental Specifications Electrical Specifications -Life Cycle: >1 million -Height: 3.50mm (0.138") -Actuation Force: 0.09 to 0.11 lbs pull force at desired distance (pull force rating is for the exterior magnet using a test plate of cold rolled steel). -Operating Temperature: up to +85°C -IP Rating of Active Area: IP64 Dimensional Diagram - Stock Linear MagnetoPots ACTIVE LENGTH [A] 8.24 [0.325] PART LENGTH [P] 7.93 [0.312] 20.32 [0.800] 3.81 [0.150] ACTIVE WIDTH 10.16 [0.400] TAIL WIDTHTAIL LENGTH [T] PIN 1 A 50.00mm 1.969" 100.00mm 3.937" 150.00mm 5.906" 200.00mm 7.874" 300.00mm 11.811" 400.00mm 15.748" 500.00mm 19.685" P 65.86mm 2.593" 25.00mm 0.984" 40.86mm 1.609" 12.50mm 0.492" 28.36mm 1.117" 115.86mm 4.562" 165.86mm 6.531" 215.86mm 8.499" 171.89mm 6.768" 185.86mm 7.318" 315.86mm 12.436" 415.86mm 16.373" 515.86mm 20.310" 750.00mm 29.528" 1000.00mm 39.370" 765.86mm 30.153" 1015.86mm 39.995" T 24.89mm 0.980" 12.70mm 0.500"

How to Order - MagnetoPots Crimpflex Solder Tab (ST) Crimpflex Female Receptacles with a Plain Housing (RH) Crimpflex Female Receptacles with a Latch Housing (RL) Crimpflex Female Receptacles with a Detent Housing (RD) Crimpflex Short Male Pins (MP) spectrasymbol.com (888) 795-2283Page 2 Standard Connector Options 103L Model L = Linear MP1 Series MP1 = MagnetoPot Active Length 0050 ST Connectors ST = Solder Tab MP = Male Pins RH = Receptacles w/Plain Housing RL = Receptacles w/Latch* Housing RD = Receptacles w/Detent* Housing * Please note that the RL and RD style connectors are only available in one orientation. Please contact Spectra Symbol for more infomation. Electrical Schematic Material Cross-Section 0.05 [0.002] 3M ADHESIVE 3.28 [0.129] CIRCUIT Electrical Schematic 10K (RIGHT BUS BAR) PIN 3 (GND) PIN 1 PIN 2 (V+) (LEFT BUS BAR) (COLLECTOR) Ind. Linearity 5% = ±5% 0012 = 12,5mm 0025 = 25mm 0050 = 50mm 0100 = 100mm 0150 = 150mm 0172 = 172mm 0200 = 200mm 0300 = 300mm 0400 = 400mm 0500 = 500mm 0750 = 750mm 1000 = 1000mm Resistance Active Lengths < 300mm 103 = 10 KOhm Active Lengths > 300mm 203 = 20 KOhm

spectrasymbol.com (888) 795-2283Page 3 Customization How It Works The MagnetoPot is simple, yet elegant in its ability to track motion in a contactless manner . A magnet on the inside of a cylinder , or a magnet on the opposing side of a motion device will guide the built-in magnetics of th e MagnetoPot for position location through a potentiometric output. The MagnetoPot is a sealed potentiometer , in the membrane potentiometer tradition, yet it does not require a wiper/actuator to connect the collector and the resistor. Instead, the MagnetoPot is controlled by an outs ide magnet, which attracts the magnetic forces within the MagnetoPot to connect to the linear resistor and give linear potentiometer feedback. The wiper inside the sealed pot is magnetic or ferromagnetic, and will only perform if connected with an exterior magnet. As opposed to a magnetically-based Reed Switch, which gives simply “open” or “close” signals, the MagnetoPot gives the full linear travel of a hydraulic or pneumatic cylinder. In liquid level applications, the MagnetoPot can attach to the outside of a liquid tank and give position of the magnet inside the float. No water ingress, no wearing of the part by environment, because the MagnetoPot is outside of the tank. Design and Contruction The MagnetoPot is made of polyester, fiberglass and kapton, depending on the specification required. It functions as a voltage divider, a resistor or rheostat, as desired by the end-user . By bringing the exterior magnet into a proximity necessary to connect with the internal magnetic attractors, the operator can obtain linear position sensing based on the location of the exterior magnet. As the exterior magnet moves, so does the electrical output of the MagnetoPot. The MagnetoPot should not be mounted to a ferromagnetic surface. Customize the size and shape. Such custom requests, for example, can be: custom lengths 10mm-1200mm; custom rotary diameters, etc. Spectra Symbol would be glad to quote your custom application, just contact us at sales@spectrasymbol.com or (888)795-2283.

spectrasymbol.com (888) 795-2283Page 4 Diagram - Stock Rotary MagnetoPot How to Order - Rotary MagnetoPot Electrical Schematic Material Cross-Section 10K (RIGHT BUS BAR) PIN 3 (GND) PIN 2 PIN 1 (V+) (LEFT BUS BAR) (COLLECTOR) 0.05 [0.002] 3M ADHESIVE 3.28 [0.129] CIRCUIT0353 Active Angle R Model R = Rotary MP1 0046 = 45.57mm 0353 = 353° 0046 103 Resistance 103 = 10 KOhm Center of Active Track Connectors ST = Solder Tab MP = Male Pins RH = Receptacles w/Plain Housing RL = Receptacles w/Latch Housing RD = Receptacles w/Detent Housing ST5% Ind. Linearity 5% = ±5% Series MP1 = MagnetoPot 6.08 [0.239] (TYP) 79.01 [3.111] 4.83 [0.190] ACTIVE WIDTH R12.70 [R0.500] THRU R32.87 [R1.294] OUTER DIAMETER 353° ACTIVE ANGLE 10.16 [0.400] PIN 1 Ø45.57 [Ø1.794] CENTER OF TRACK 2xR1.59 [R0.062]