DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 10
Technical content
For general signal lineɹ GHz noise countermeasure (general signal line, high-speed signal line) EMC Components MMZ1005-E 1005[0402 inch]* * Dimensions Code JIS[EIA] Chip Beads MMZ1005-E Type MMZ-E Series
(2/10) 20150209 / beads_commercial_signal_mmz1005-e_en.fm EMC Components REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 7 5% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150°C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set therm al design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose
applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. REMINDERS
(3/10) 20150209 / beads_commercial_signal_mmz1005-e_en.fm Please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. EMC Components Chip Beads For general signal lineɹ GHz noise countermeasure (general signal line, high-speed signal line)
FEATURES
Noise reduction solution for general signal line. Compared to the MMZ Series, it is a product that increases the SRF to GHz bands and can countermeasure nose at wide frequencies with 1 element. Compared to the MMZ Series, it can attain high impedance at GHz bands. Various frequency characteristics with 4 materials of different features for countermeasures against everything from general si gnals to high-speed signals. APPLICATION Noise removal for mobile devices such as smartphones and tablet terminals, and various modules. Noise removal for PCs and recorders, household appliances such as STBs, smart grids, and industrial equipment. PART NUMBER CONSTRUCTION OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT /g13/g3The Storage temperature range is for after the circuit board is mounted. Overview of MMZ1005-E Type MMZ 1005 S 601 E T 000 Series name L×W×T Dimensions Material name Impedance Characteristic type Packaging style Internal code(mm) (/g58) at 100MHz 1005 1.0×0.5x0.5 S 601 600 E T Taping 000 A 102 1000 D F Type Temperature range Package quantity Individual weight Operating temperature ʢ°Cʣ Storage temperature/g13 ʢ°Cʣ (pieces/reel) ʢmgʣ MMZ1005-E –55 to +125 –55 to +125 10,000 1 Product compatible with RoHS directive Halogen-free Compatible with lead-free solders RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://product.tdk.com/en/environment/rohs/ Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br conte nt is less than 1500ppm.
(4/10) 20150209 / beads_commercial_signal_mmz1005-e_en.fm Please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. EMC Components MMZ1005-E Type RECOMMENDED REFLOW PROFILE Preheating Soldering Peak Temp. Time Temp. Time Temp. Time T1 T2 t1 T3 t2 T4 t3 150°C 180°C 60 to 120s 230°C 30 to 60s 250 to 260°C 10s Natural cooling Preheating Soldering T3 T3 t: Time Peak T: Temperature
(5/10) 20150209 / beads_commercial_signal_mmz1005-e_en.fm Please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. EMC Components MMZ1005-E Type MATERIAL CHARACTERISTICS S material: Standard type that features impedance characteristics similar to those of a typical ferrite core. For signal line ap plications in which the blocking region is near 100MHz. Impedance values selected for effectiveness at 40 to 300MHz. A material: This high-impedance product is based on the impedance frequency characteristics of our Y -material. The product offers excellent impedance characteristics, which is greater than 2500/g58, in the vicinity of 100MHz range (MMZ1608A252B). D material: For applications calling for low insertion loss at low frequencies and sharply increasing impedance at high frequen cies. Designed for high impedance at high frequencies (300MHz to 1GHz) for signal line applications. F material: This new product inherits the characteristic of our D-material, namely its sharp impedance rise time, and its impedance peak frequency has been shifted higher into range. The product offers excellent noise suppression from 600MHz to as high as in the GHz range. TYPICAL MATERIAL IMPEDANCE CHARACTERISTICSɹ 500 1000 1500 2000 2500 10 100 1000 Frequency(MHz) S A D F
(6/10) 20150209 / beads_commercial_signal_mmz1005-e_en.fm Please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. EMC Components MMZ1005-E Type SHAPE & DIMENSIONS RECOMMENDED LAND PATTERN 0.5±0.05 1±0.05 0.1min. 0.5±0.05 Dimensions in mm Dimensions in mm0.40.5 0.5 0.5
(7/10) 20150209 / beads_commercial_signal_mmz1005-e_en.fm Please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. EMC Components MMZ1005-E Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE ˓Measurement equipment ˎ Equivalent measurement equipment may be used. Impedance DC resistance Rated current Part No. [100MHz] [1GHz] (/g58) Tolerance (/g58) Tolerance (/g58)max. (mA)max. 600 ±25% 1000 ±40% 0.65 300 MMZ1005S601ET000 1000 ±25% 1400 ±40% 1.00 250 MMZ1005S102ET000 1800 ±25% 1800 ±40% 1.50 200 MMZ1005S182ET000 600 ±25% 1400 ±40% 0.80 300 MMZ1005A601ET000 1000 ±25% 2000 ±40% 1.20 250 MMZ1005A102ET000 1500 ±25% 2300 ±40% 1.60 230 MMZ1005A152ET000 1800 ±25% 2700 ±40% 2.10 200 MMZ1005A182ET000 2200 ±25% 3000 ±40% 2.20 150 MMZ1005A222ET000 120 ±25% 1000 ±40% 0.70 300 MMZ1005D121ET000 220 ±25% 1700 ±40% 1.00 250 MMZ1005D221ET000 47 ±25% 800 ±40% 0.70 300 MMZ1005F470ET000 75 ±25% 1500 ±40% 1.00 250 MMZ1005F750ET000 120 ±25% 2300 ±40% 1.50 200 MMZ1005F121ET000 Measurement item Product No. Manufacturer Impedance E4991A+16192A Agilent Technologies DC resistance Type-7556 Y okogawa
(8/10) 20150209 / beads_commercial_signal_mmz1005-e_en.fm Please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. EMC Components MMZ1005-E Type Z VS. FREQUENCY CHARACTERISTICS (BY SERIES) MMZ1005S-E SERIES MMZ1005A-E SERIES MMZ1005D-E SERIES MMZ1005F-E SERIES 10000100010010 1 Frequency (MHz) Impedance (Ω) 500 1000 1500 2000 2500 3000 MMZ1005S182E MMZ1005S102E MMZ1005S601E 1000010001001010 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 Frequency (MHz) Impedance (Ω) MMZ1005A222E MMZ1005A182E MMZ1005A152E MMZ1005A601E MMZ1005A102E 100001000100101 200 400 600 800 1000 1200 1400 1600 1800 2000 Frequency (MHz) Impedance (Ω) MMZ1005D221E MMZ1005D121E 100001000100101 500 1000 1500 2000 2500 3000 Frequency (MHz) Impedance (Ω) MMZ1005F121E MMZ1005F750E MMZ1005F470E
(9/10) 20150209 / beads_commercial_signal_mmz1005-e_en.fm Please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. EMC Components MMZ1005-E Type Z, X, R VS. FREQUENCY CHARACTERISTICS MMZ1005S601ET000 MMZ1005S102ET000 MMZ1005S182ET000 MMZ1005A601ET000 MMZ1005A102ET000 MMZ1005A152ET000 MMZ1005A182ET000 MMZ1005A222ET000 MMZ1005D121ET000 MMZ1005D221ET000 MMZ1005F470ET000 MMZ1005F750ET000 MMZ1005F121ET000 1 10 100 1000 10000 Frequency (MHz) Impedance (Ω) 200 400 600 800 1000 Z R X 1 10 100 1000 10000 Frequency (MHz) Impedance (Ω) 200 400 600 800 1000 1200 1400 1600 Z R X 1 10 100 1000 10000 Frequency (MHz) Impedance (Ω) 500 1000 1500 2000 3000 2500 Z R X 1 10 100 1000 10000 Z R 200 400 600 800 1000 1200 1400 1600 X Frequency (MHz) Impedance (Ω) 1 10 100 1000 10000 Frequency (MHz) Impedance (Ω) 500 1000 1500 2000 2500 3000 Z R X 1 10 100 1000 10000 Frequency (MHz) Impedance (Ω) 500 1000 1500 2000 2500 Z R X 1 10 100 1000 10000 X Frequency (MHz) Impedance (Ω) 500 1000 1500 2000 3500 3000 2500 Z R 1 10 100 1000 10000 Frequency (MHz) Impedance (Ω) 500 1000 1500 2000 4500 3500 3000 4000 2500 Z R X 1 10 100 1000 100000 200 400 600 800 1000 1200 Z R X Frequency (MHz) Impedance (Ω) 1 10 100 1000 10000 Frequency (MHz) Impedance (Ω) Z R X 500 1000 1500 2000 1 10 100 1000 10000 Frequency (MHz) Impedance (Ω) 200 400 600 800 1000 1200 Z R X 1 10 100 1000 10000 Frequency (MHz) Impedance (Ω) 200 400 600 800 1000 1200 1400 1600 1800 Z R X 1 10 100 1000 10000 X Frequency (MHz) Impedance (Ω) 500 1000 1500 2000 2500 3000 Z R
(10/10) 20150209 / beads_commercial_signal_mmz1005-e_en.fm Please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. EMC Components MMZ1005-E Type PACKAGING STYLE REEL DIMENSIONS TAPE DIMENSIONS Dimensions in mm Type A B P1 K ø180±2.0 2.0±0.5 ø13±0.2 ø21±0.8 Dimensions in mm 1.0 ø60min. 14.4max. 8.4 +2.0 –0.0 4.0±0.12.0±0.05 B A P1 8.0±0.3 1.75±0.1 3.5±0.05 K 1.5 +0.1 160min. Taping 200min. 300min.Drawing direction Dimensions in mm