MM930LITE | DigiCamel IC Datasheet

Online Datasheet

Read MM930LITE online.

MM930LITE BRIDGETEK | Alldatasheet

Document overview

Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
PDF pages: 22

Technical content

Neither the whole nor any part of the information contained in, or the product described in this manu al, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. This product and its documentation are supplied on an as -is basis and no warranty as to their suitability for any particular purp ose is either made or implied. Bridgetek Pte Ltd will not accept any claim for damages howsoever arising as a result of use or failure of this prod uct. Your statutory rights are not affected. This product or any variant of it is not intended for use in any medical appliance, device or system in which the failure of the product might reasonably be expected to result in personal injury. This document provides preliminary information that may be subject to change without notice. No freedom to use patents or ot her intellectual property rights is implied by the publication of this document. Bridgetek Pte Ltd, 178 Paya Lebar Road, #07 -03, Singapore 409030. Singapore Registered Company Number: 201542387H Copyright © Bridgetek Pte Ltd 1 MM930Lite Datasheet Version 1.0 Document Reference No.: BRT_000085 Clearance No.: BRT#069 Bridgetek Pte Ltd Datasheet MM930Lite Development Module FT93x Family is a General Purpose 32-bit Microcontroller

1 Introduction

The MM930Lite is a development module for Bridgetek’s 32 -bit high performance FT93x Microcontroller family, which is used to develop and demonstrate the functionality of the FT930 Embedded Microcontroller. This module is ideal for applications including home security systems, home automation systems, USB capability products, embedded multimedia application and other industrial control systems.

1.1 Features

For a full list of the FT93x features refer to the FT93x datasheet. In addition, the MM930Lite module has the following features:  FT930Q 68-pin QFN package microcontroller.  Micro SD card socket support.  In built 8M Byte Eflash memory.  A Micro-B USB for connecting to a USB host or providing a power supply over USB for the board.  2x8 pins 2.54mm pitch dual entry female header and 16 pins 0.5mm pitch FFC/FPC connectors for SPI master to support LCD display modules.  2x5 pins 1.27mm pitch female Micro-MaTch connector for software download.  2x20 pins 2.54mm pitch female header support for external feature expansions.  +5V alternative power supply DC connector.  Hardware Reset button provided.

2 Ordering Information

Part No. Description MM930Lite FT930 module, a FT32, 32-bit microcontroller with 128kB flash memory, 32kB data RAM and 128kB program memory embedded. SD3.0, USB2.0 Device, 8MB Eflash, several interface pin headers and connectors included. Table 2-1 – Ordering information

3 Program Support

Example applications are provided for the MM930Lite module by Bridgetek. The following documents provide further details for software development. Other relevant documents and examples exist so please see the Bridgetek website for further information. Refer to BRT_AN_010_FT93x_User_Manual for system register information.

4 Board Layout

The MM930Lite development board is a 55 mm x 85 mm ( Not including the 4 mounting holes) four-layer printed circuit board. The layout is as shown in Figure 4-1. Figure 4-1 – MM930Lite Board Layout Key Features: 1. Micro SD card socket 2. Micro-MaTch connector 3. Dual-entry female header 4. FPC/FFC connector (located beneath board) 5. Alternative power supply jumper 6. +5V DC power socket 7. USB Micro-B connector 8. H/W Reset button 9. FT930Q QFN68 Microcontroller 10. External I/O bus female pin header 11. LDO regulator 12. 8M Byte Eflash memory 11 12 1 5 6 7 8 9

4.1 Power Supply

The MM930Lite development board provides optional power supply sources with JP1 jumper: 1. +5V DC power supply, CN6 right angle connector. 2. Over USB via the Micro-B USB CN3 port. Pin No. Name 1-2 USB VBUS power supply 2-3 +5V DC power supply Table 4-1 – JP1 Pinout A red LED (LED1) will illuminate after the +5V power supply is applied. This supply will a lso drive a fixed +3.3V LDO regulator which will provide power to all peripherals of the FT930 microcontroller. Figure 4-2– Power supply Power supply +3.3V LDO Power Jumper Power Jack Micro USB port

4.2 Microcontroller

The F T930Q 68-pin QFN microcontroller (U1) provided on the board belongs to the 32-bit FT9 3x Microcontroller family from Bridgetek. For detail s of the FT930 Microcontroller, refer to the FT93x datasheet. Figure 4-3– FT930 Microcontroller There are two crystals used on the MM930Lite development board. The 12MHz crystal (Y1) is the primary system clock frequency supplying the FT9 30Q IC. The 32.768 KHz crystal (Y2) is the system clock frequency supporting the internal RTC. The FT930Q IC on this board is operated with a single supply of +3.3V. The FT9xx Core +1.2V from internal regulator is used as powe r source for internal RTC . These power output pins have decoupling capacitors as specified in the datasheet.

4.3 Micro SD Connector

The FT930Q Microcontroller has a SD3.0 controller to support different speed classes, physical sizes and capacities of Secure Digital ( SD) cards. There is a Micro SD connector on the MM930Lite development module for inserting Micro SD cards (11 x15 x1.0 mm). There are three standard capacity cards supported:  Secure Digital (SD) standard – Up to 2GB SD memory card  Secure Digital High Capacity (SDHC) standard – Over 2GB-32GB SDHC memory card  Secure Digital eXtended Capacity (SDXC) standard – Over 32GB-2TB SDXC memory card Standard class speeds 2, 4, 6, 10, and Ultra High Speed ( UHS) classes U1 and U3 are all supported. The design of the physical interface supports 4-bit SD bus mode and card detection. Figure 4-4– Micro SD Connector

4.4 USB Connector

There is a USB connector provided on the MM9 30Lite board. CN3 is a Micro -B type USB2.0 connector which is used for connecting the module to a USB host. Figure 4-5– USB Connectors

4.5 Programmer Interface

The programmer interface CN5, 2x5 pins 1.27mm pitch female M icro-Match header supports software application download, GDB debugging on the MM930Lite development board with the UMFTPD2A module..

4.5.1 CN5 – 10-pin Micro-Match Program Interface Signals

Pin No. Name Type Description 1~6 - - -

7 GND P Ground

8 DEBUG I/O FT90x One-Wire Interface

9 GDB_5V P External 5V power supply

10 RESETn P H/W Reset, active low

Table 4-2 – CN5 Pinout

4.6 SPI Master Interface

The FT930Q microcontroller has a SPI master interface that supports single, dual an d quad SPI data transfer modes. There are two alternative connectors for supporting different LCD display modules as SPI slave devices.  The J1 dual-entry 2x8 pins 2.54mm pitch , female header (located on top of board Error! Reference source not found. ) is designed for FT80x and FT81x Embedded Video Engine (EVE) family LCD display modules. As an example the ME810A-HV35R module, can connect directly to the MM930Lite development board on the bottom side with a male pin header.  The CN4 16 pins 0.5mm pitch, bottom contact FFC/FPC connector (located beneath boardError! Reference source not found. ) provides an alternative connection for LCD display modules that meet FT80x or FT81X chip technical specification s and use a 16-pin 0.5mm pitch flexible flat cable to link to the board. Figure 4-7– SPI Master Interface

4.6.1 J1 – 16-pin Dual Entry Header, SPI Master and Control Signals

Pin No. Name Type Description

1 SPIM_SCK O SPI Master clock output

2 SPIM_SSn0 O SPI Master chip select 0, active low

3 SPIM_MISO I/O

SPI Master input, Slave output Data 1 for Quad SPI

4 SPIM_MOSI I/O

SPI Master output, Slave input Data 0 for Quad SPI

5 SPIM_IO3 I/O General I/O, data 3 for Quad SPI

6 SPIM_IO2 I/O General I/O, data 2 for Quad SPI

7 DCX O

Data / command selection pin for LCD controller Low: Command High: Parameter

8 CS1# O SPI Master chip select 1, active low for LCD

9 VCCIO_3V3 P +3.3V power supply

10 VDD_5V P +5V power supply

11 GND P Ground

12 GND P Ground

13 PWD# O FT80X power down control, active low

14 INT# I Interrupt input from FT80X, active low

15 AUD_LIN I Audio PWM input from FT80X

16 DISP O LCD display enable

Table 4-3 – J1 Pinout

4.6.2 CN4 – 16-pin FPC/FFC connector

Pin No. Name Type Description 1,2 VCCIO_3V3 P +3.3V Power supply

3 SPIM_SCK O SPI Master clock output

4 SPIM_IO3 I/O General I/O, data 3 for Quad SPI

5 SPIM_IO2 I/O General I/O, data 2 for Quad SPI

6 SPIM_MISO I/O

SPI Master input, Slave output Data 1 for Quad SPI

7 SPIM_MOSI I/O

SPI Master output, Slave input Data 0 for Quad SPI

8 SPIM_SSn0 O SPI Master chip select 0, active low

9 INT# I Interrupt input from FT80X, active low

10 PWD# O FT80X power down control, active low

11,12,14 GND P Ground

13 AUD_LIN I Audio PWM input from FT80X

15 DISP O LCD display enable

16 MODE O

Serial interface selection for FT80X Low: SPI interface High: I2C interface Table 4-4 – CN4 Pinout

4.7 External I/O Bus

There are 23 multiple function GPIOs provided on CN1 2x20 pins, 2.54mm pitch female header. External feature boards may connect via UART, PWM, ADC, DAC, SPI and I2C on these IO connectors. Table 4-5 lists all features assigned for each pin.

4.7.1 CN1 – 40-pin Dual Entry Header, Multiple function GPIO & Control

Pin No. Function 1 Function 2 Function 3 Function 4

2 FT800_AUDL - - -

4 GPIO23 UART0_TXD PWM2 -

6 GPIO22 UART0_RXD PWM3 -

7 DAC1 - - -

8 GPIO24 UART0_RTS PWM1 -

9 DAC0 - - -

10 GPIO25 UART0_CTS PWM0 -

11,25,26 - - - -

12 GPIO9 PWM2 - -

13 GPIO11 PWM0 - -

14 GPIO10 PWM1 - -

16 VDD_5V - - -

17 GPIO33 SPIM_SSn3 - -

18 GPIO34 SPIM_SCK SPIS_SCK -

19 GPIO35 SPIM_MISO SPIS_MISO -

20 GPIO36 SPIM_MOSI SPIS_MOSI -

21 GPIO38 SPIM_IO3 RTC_REF -

22 GPIO37 SPIM_IO2 SPIS_SS -

23 VCCIO_3V3 - - -

27 GPIO20 UART3_RTS - -

28 GPIO21 UART3_CTS - -

29 GPIO18 UART3_RXD - -

30 GPIO19 UART3_TXD - -

31 GPIO29 UART0_RI UART1_CTS -

32 GPIO28 UART0_DCD UART1_RTS -

33 GPIO27 UART0_DSR UART1_TXD -

34 GPIO26 UART0_DTR UART1_RXD -

35 ADC2 - - -

36 ADC1 - - -

37 ADC3 - - -

38 GPIO17 I2CM_SDA I2CS_SDA -

39 RESETn - - -

40 GPIO18 I2CM_SCL I2CS_SCL -

Table 4-5 – CN1 External I/O Bus Figure 4-8– External I/O Bus

5 Board Schematic

Figure 5-1 – MM930Lite MCU and External I/O Bus

6 Mechanical Dimensions

6.1 MM930Lite PCB Dimensions

Figure 6-1 – MM930Lite PCB Dimensions

7 Contact Information

Head Quarters – Singapore Branch Office – Taipei, Taiwan Bridgetek Pte Ltd

178 Paya Lebar Road, #07-03

Tel: +65 6547 4827 Fax: +65 6841 6071 Bridgetek Pte Ltd, Taiwan Branch 2 Floor, No. 516, Sec. 1, Nei Hu Road, Nei Hu District Taipei 114 Taiwan , R.O.C. Tel: +886 (2) 8797 5691 Fax: +886 (2) 8751 9737 E-mail (Sales) sales.apac@brtchip.com E-mail (Sales) sales.apac@brtchip.com E-mail (Support) support.apac@brtchip.com E-mail (Support) support.apac@brtchip.com Branch Office - Glasgow, United Kingdom Branch Office – Vietnam Bridgetek Pte. Ltd. Unit 1, 2 Seaward Place, Centurion Business Park Glasgow G41 1HH United Kingdom Tel: +44 (0) 141 429 2777 Fax: +44 (0) 141 429 2758 Bridgetek VietNam Company Limited Lutaco Tower Building, 5th Floor, 173A Nguyen Van Troi, Ward 11, Phu Nhuan District, Ho Chi Minh City, Vietnam Tel : 08 38453222 Fax : 08 38455222 E-mail (Sales) sales.emea@brtichip.com E-mail (Sales) sales.apac@brtchip.com E-mail (Support) support.emea@brtchip.com E-mail (Support) support.apac@brtchip.com Web Site http://brtchip.com/ Distributor and Sales Representatives Please visit the Sales Network page of th e Bridgetek Web site for the contact details of our distributor(s) and sales representative(s) in your country. System and equipment manufacturers and designers are responsible to ensure that their systems, and any Bridgetek Pte Ltd (BRT Chip) devices incorporated in their systems, meet all applicable safety, regulatory and system -level performance requirements. All application-related information in this document (including application descriptions, suggest ed Bridgetek devices and other materials) is provided for reference only. While Bridgetek has taken care to assure it is accurate, this information is subject to customer confirmation, and Bridgetek disclaims all liability for system designs and for any ap plications assistance provided by Bridgetek. Use of Bridgetek devices in life support and/or safety applications is entirely at the user’s risk, and the user agrees to defend, i ndemnify and hold harmless Bridgetek from any and all damages, claims, suits or expense resulting from such use. This document is subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Neither the whole nor any part of the information contained in, or the product described in this document, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. Bridgetek Pte Ltd, 1 78 Paya Lebar Road, #07-03, Singapore 409030. Singapore Registered Company Number: 201542387H.

Copyright © Bridgetek Pte Ltd 20 MM930Lite Datasheet Version 1.0 Document Reference No.: BRT_000085 Clearance No.: BRT#069 Appendix A - References Document References FT93X webpage: http://brtchip.com/product/ FT93x datasheet: FT930/FT931/FT932/FT933 Datasheet BRT_AN_010_FT93x_User_Manual UMFTPD2A program module datasheet: DS_UMFTPD2A ME810A-HV35R LCD display module document: DS_ME810A_HV35R Acronyms and Abbreviations Terms Description USB Universal Serial Bus QFN Quad-Flat No-leads FFC/FPC Flexible Flat Cable/Flexible Printed Circuit LCD Liquid Crystal Display DC Direct Current RAM Random Access Memory SD Secure Digital H/W Hardware LDO Low Drop-Out LED Light-Emitting Diode RTC Real-Time Clock I/O Input/Output I2C Inter-Integrated Circuit SPI Serial Peripheral Interface UART Universal Asynchronous Receiver/Transmitter PWM Pulse Width Modulation ADC Analog-to-Digital Converter DAC Digital-to-Analog Converter

Copyright © Bridgetek Pte Ltd 22 MM930Lite Datasheet Version 1.0 Document Reference No.: BRT_000085 Clearance No.: BRT#069 Appendix C – Revision History Document Title: MM930Lite Datasheet Document Reference No.: BRT_000085 Clearance No.: BRT#069 Product Page: http://brtchip.com/product/ Document Feedback: Send Feedback Revision Changes Date Version 1.0 Initial Release 2017-06-08

Product Information

MM930LITE specifications and overview.

Summary

Development Module Version 1.0

Description

Development Module Version 1.0

Source title MM930LITE Datasheet(PDF) - Bridgetek Pte Ltd.

Related Parts

More parts from the same family.

Browse manufacturer