MM8930-2620B MURATA1 | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 3
Technical content
Preliminary Specification of COAXIAL CONNECTOR Written by : H. Kitaguchi Preliminary SPEC No. : NMM04-PU0025A Checked by : T. Kuriyama Part Number : MM8930-2620B/RJ4/RK15 Date : 14 /Jun./2013 SPECIFICATION Revised A: 18/Jul./’13 MA 1. PART NUMBER Part Number Packaging Quantity Remarks MM8930-2620B Bulk Package Free MM8930-2620RJ4 178 mm dia. reel 4000 pcs/reel ESD protection MM8930-2620RK15 330 mm dia. reel 15000 pcs/reel ESD protection 2. MECHANICAL 1.7 Dia. 0.8 1.6 1.6 Dia. 1.2 0.3 0.7 0.55 0.38 0.18 0.12 0.12 0.2 0.8 0.08 RF ANT GROUND Signal out Probe Signal in Probe Signal out Signal in Circuit diagram Probe Signal out Signal in Signal in Probe Signal out RF RF RFANT. ANT. ANT. FIGURE1. Construction 3. RATING : Item Specification Voltage Rating 30V r.m.s. maximum Nominal Frequency Range DC to 6GHz Nominal Impedance 50Ω Power Rating 2Wmax (at 2GHz) Temperature Rating -40℃ to +85℃ Insulation Resistance 500 M Ω minimum Withstanding Voltage No evidence of break down in AC200Vr.m.s, 1minute Initial Contact Resistance (without conductor resistance) 70mΩmax. 1.3 max. (3GHz to 6GHz) Insertion Loss 0.1dB max. (DC to 3GHz) 0.2dB max. (3GHz to 6GHz) Isolation Signal in : RF 20dBmin. (DC∼3GHz) Signal in : RF 15dBmin. (3GHz ∼6GHz) Signal in : ANT 18dBmin. (DC∼3GHz) Signal in : ANT 13dBmin. (3GHz ∼6GHz) Durability 50 cycles Scale: Free Tolerances Unless Otherwise Specified: +/- 0.2 Unit:mm
Preliminary Specification of COAXIAL CONNECTOR Written by : H. Kitaguchi Preliminary SPEC No. : NMM04-PU0025A Checked by : T. Kuriyama Part Number : MM8930-2620B/RJ4/RK15 Date : 14 /Jun./2013 4. STANDARD PATTERN DIMENSION 1.3 1.8 0.45 1.7 0.45 0.7 0.8 3.2 0.35 4.2 1.11.03 Ground 0.3 RF Antenna 1.7 0.45 1.7 Non-regist area Non-regist area ⋅The solder resist should be printed except for the land pattern and, Non-regist area on the PWB FIGURE2. Standard pattern dimensions There is the possibility to have the contact failure by excess flux in solder, if non-regist area is not secured. 5. STANDARD STENCIL MASK PATTERN The standard stencil mask pattern is as FIGURE 3. There is the possibility to have the contact failure by solder shifting into contact point, if the excess solder is used by non standard stencil mask pattern Thickness t=0.08mm Thickness t=0.1mm 0.25 1.6 1.1 1.8 1.7 1.3 0.45 0.23 1.6 1.1 1.8 1.55 0.55 1.36 FIGURE3. Standard stencil mask pattern
Preliminary Specification of COAXIAL CONNECTOR Written by : H. Kitaguchi Preliminary SPEC No. : NMM04-PU0025A Checked by : T. Kuriyama Part Number : MM8930-2620B/RJ4/RK15 Date : 14 /Jun./2013 ! CAUTION Limitation of Applications Please do not use our products for the applications listed below which require specially high reliability for the prevention of defects which may directly or indirectly cause damage to the third party's life, body or property. (1) Aircraft equipment (2) Aerospace equipment (3) Undersea equipment (4) Power plant control equipment (5) Medical equipment (6) Transportation equipment (vehicles, trains, ships, etc.) (7) Traffic signal equipment (8) Disaster prevention / crime prevention equipment (9) Data-processing equipment (10) Application of similar complexity and/or reliabilit y requirements to the applications listed in the above.