MKP10

MKP10 WIMA | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 6

Technical content

1 1.08 D WIMA MKP 10 Polypropylene (PP) Capacitors for Pulse Applications with Double-Sided Metallized Electrodes and Schoopage Contacts PCM 7.5 mm to 37.5 mm Special Features Electrical Data ˜ P ulse duty construction ˜ S elf-healing ˜ V ery low dissipation factor ˜ N egative capacitance change v ersus temperature ˜ A ccording to RoHS 2002/95/EC Typical Applications For pulse applications e.g. ˜ S witch mode power supplies ˜ T V and monitor sets ˜ L ighting ˜ A udio/video equipment Construction Dielectric: Polypropylene (PP) film Capacitor electrodes: Double-sided metallized plastic film Internal construction: MKP 10: 63 VAC, 180 VAC, 250 VAC MKP 10: 400 VAC, 600 VAC, 650 VAC, 700 VAC MKP 10: 900 VAC (PCM 15 = 3-section) Plastic film Electrode carrier plastic film metallized on both sides Metal contact layer (schoopage) T erminating wire Plastic film Electrode carrier plastic film metallized on both sides Metal contact layer (schoopage) T erminating wire Plastic film metallized on one side Plastic film Electrode carrier plastic film metallized on both sides Metal contact layer (schoopage) T erminating wire Plastic film metallized on one side Encapsulation: Solvent-resistant, flame-retardant plastic case with epoxy resin seal, UL 94 V-0 Terminations: Tinned wire. Marking: Colour: Red. Marking: Black. Epoxy resin seal: Red Capacitance range: 1000 pF to 15 mF (E12-values on request) Rated voltages:

100 VDC, 250 VDC, 400 VDC, 630 VDC,

1000 VDC, 1600 VDC, 2000 VDC, 2500 VDC

Capacitance tolerances: ±20%, ±10%, ±5% Operating temperature range: –55) C to +100 ) C Climatic test category: 55/100/56 in accordance with IEC Insulation resistance at +20 + C: C T 0.33 mF:  1 x 10 5 M¸ (mean value: 5 x 10 5 M¸) C  0.33 mF:  30 000 sec (M ¸ x mF) mean value: 100 000 sec) Measuring voltage: 100 V/1 min. Dissipation factors at + 20 ) C: tan d at f C T 0.1 mF 0 .1 mF < C T 1.0 mF C > 1.0 mF 1 kHz T 3 x 10 -4 T 3 x 10 -4 T 3 x 10 -4 10 kHz T 4 x 10 -4 T 6 x 10 -4 – 00 kHz T 15 x 10 -4 – – Maximum pulse rise time: Capacitance max. pulse rise time V/ msec at T A < 40 ) C p F/mF 100 VDC 250 VDC 400 VDC 630 VDC 1000 VDC 1600 VDC 2000 VDC 2500 VDC 1000 ... 2200 1000 1800 1800 1800 2800 5400 9000 1 1000 300 ... 6800 900 1200 1200 1200 2800 5400 9000 1 1000 for pulses equal to the rated voltage Test voltage: 1.6 U r, 2 sec. Dielectric absorption: .05 % Voltage derating: A voltage derating factor of 1.35 % per K must be applied from +85 + C for DC voltages and from +75 + C for AC voltages. Reliability: Operational life  300 000 hours Failure rate  1 fit (0.5 x U r and 40 ) C) Mechanical Tests Pull test on leads: d T 0.8 l: 10 N in direction of leads d > 0.8 l: 20 N in direction of leads according to IEC 60068-2-21 Vibration: hours at 10 ... 2000 Hz and 0.75 mm displacement amplitude or 10 g in accordance with IEC 60068-2-6 Low air density: 1kPa = 10 mbar in accordance with IEC 60068-2-13 Bump test: 4000 bumps at 390 m/sec in accordance with IEC 60068-2-29 Packing Available taped and reeled up to and including case size 15 x 26 x 31.5 / P CM 27.5 mm. Detailed taping information and graphs at the end of the catalogue. For further details and graphs please refer to Technical Information.

1 1.08 Continuation General Data D WIMA MKP 10 Capacitance 100 VDC/63 VAC * 250 VDC/180 VAC * 400 VDC/250 VAC * 630 VDC/400 VAC * W H L PCM W H L PCM W H L PCM W H L PCM 000 pF 4 9 10 7.5 4 9 10 7.5 4 9 10 7.5 4 9 10 7.5 1500 „ 4 9 10 7.5 4 9 10 7.5 4 9 10 7.5 4 9 10 7.5 2200 „ 4 9 10 7.5 4 9 10 7.5 4 9 10 7.5 4 9 10 7.5 3300 „ 4 9 10 7.5 4 9 10 7.5 4 9 10 7.5 4 9 10 7.5 4700 „ 4 9 10 7.5 4 9 10 7.5 4 9 10 7.5 4 9 10 7.5 6800 „ 4 9 10 7.5 4 9 10 7.5 4 9 10 7.5 4 9 10 7.5 4 9 13 10 * 4 9 13 10 * 4 9 13 10 * 4 9 13 10 * 4 9 13 10 * 4 9 13 10 * 5 1 1 18 15 * 4 9 13 10 * 4 9 13 10 * 5 1 1 18 15 * 4 9 13 10 * 4 9 13 10 * 5 1 1 13 10 * 5 1 1 18 15 * 4 9 13 10 * 4 9 13 10 * 5 1 1 18 15 * 6 15 26.5 22.5 * 0.068 „ 5 1 1 13 10 5 1 1 13 10 * 6 12.5 18 15 * 7 14 18 15 * 5 1 1 18 15 * 6 15 26.5 22.5 * 6 15 26.5 22.5 * 0.1 mF 6 12 13 10 6 12 13 10 * 7 14 18 15 * 9 16 18 15 * 13 24 41.5 37.5 * 17 29 41.5 37.5 * 17 29 41.5 37.5 * 17 29 41.5 37.5 * 19 32 41.5 37.5 * 15 „ 24 45.5 41.5 37.5 * AC voltage: f T 1000 Hz; 1.4 x U rms + UDC T Ur ** PCM = Printed circuit module = lead spacing * O n ordering please state the required PCM (lead spacing)! I f not specified, smaller PCM will be booked. ** Admissible AC voltage 280 VAC max . Dims. in mm. Ionisation inception level in isolated cases may be lower than admissible AC voltage. Taped version see page 121. Rights reserved to amend design data without prior notification. Continuation page 70 PCM at the lead exit points ( 0.4) LW H d 6 -2 P d PCM 0.6 7.5 - 10 .8 15 - 27.5 .0 37.5

1 1.08 WIMA FKP 4 Continuation General Data D Capacitance 1000 VDC/600 VAC * 1600 VDC/650 VAC * 2000 VDC/700 VAC * 2500 VDC/900 VAC * W H L PCM W H L PCM W H L PCM W H L PCM 000 pF 4 9 10 7.5* 4 9 13 10 4 9 13 10 5 1 1 18 15 * 4 9 13 10 * 6 15 26.5 22.5 * 1500 „ 4 9 10 7.5* 4 9 13 10 4 9 13 10 5 1 1 18 15 * 4 9 13 10 * 6 15 26.5 22.5 200 „ 4 9 10 7.5* 4 9 13 10 5 1 1 13 10 * 5 1 1 18 15 * 4 9 13 10 * 5 1 1 18 15 * 6 15 26.5 22.5 * 3300 „ 4 9 10 7.5* 4 9 13 10 5 1 1 18 15 5 1 1 18 15 * 4 9 13 10 * 6 15 26.5 22.5 * 4 9 13 10 * 6 15 26.5 22.5 * 6 15 26.5 22.5 * 5 1 1 18 15 * 6 15 26.5 22.5 * 5 1 1 18 15 * 6 15 26.5 22.5 * 6 15 26.5 22.5 * 0.022 „ 6 12.5 18 15 * 7 14 18 15 * 9 16 18 15 * 1 1 21 26.5 22.5 9 19 31.5 27.5 * 1 1 21 31.5 27.5 * 1 1 21 31.5 27.5 * 1 1 21 31.5 27.5 * 1 1 21 31.5 27.5 * 13 24 41.5 37.5 * 13 24 41.5 37.5 * 17 29 41.5 37.5 * 13 24 41.5 37.5 * 17 29 41.5 37.5 * 13 24 41.5 37.5 * 19 32 41.5 37.5 * 17 29 41.5 37.5 * .5 „ 24 45.5 41.5 37.5 * AC voltage: f T 1000 Hz; 1.4 x U rms + UDC T Ur ** PCM = Printed circuit module = lead spacing * O n ordering please state the required PCM (lead spacing)! I f not specified, smaller PCM will be booked. Dims. in mm. Ionisation inception level in isolated cases may be lower than admissible rated AC voltage. Taped version see page 121. Rights reserved to amend design data without prior notification. WIMA MKP 10 PCM at the lead exit points ( 0.4) LW H d 6 -2 Continuation page 71 P d PCM 0.6 7.5 - 10 .8 15 - 27.5 .0 37.5

1 1.08 D Permissible AC voltage in relation to frequency at 10 ) C internal temperature rise (general guide). 400VDC f Hz 10 2 5 10 2 5 10 2 5 103 4 5 6 250 U V rms 0.022 µF 0.01 µF 4700 pF 2200 pF1000 pF 100 pF 0.47 µF 1.0 µF 1.5 µF 0.22 µF 0.047 µF 0.1 µF 630VDC f Hz 10 2 5 10 2 5 10 2 5 103 4 5 6 350 U V rms 4700 pF 2200 pF 1000 pF 470 pF 100 pF 0.47 µF 1.0 µF 1.5 µF 0.047 µF 0.1 µF 0.22 µF 0.022 µF 0.01 µF 1000VDC f Hz 10 2 5 10 2 5 10 2 5 103 4 5 6 400 U V rms 2200 pF 1000 pF470 pF 100 pF 0.022 µF 0.01 µF 0.047 µF 0.1 µF 0.22 µF 0.47 µF 1.0 µF 4700 pF 1250VDC f Hz 10 2 5 10 2 5 10 2 5 103 4 5 6 450 U V rms 2200 pF 0.047 µF 0.022 µF 0.01 µF 0.1 µ F 0.22 µF 0.47 µF 0.68 µF 4700 pF 1000 pF 470 pF 100 pF 1600VDC f Hz 10 2 5 10 2 5 10 2 5 103 4 5 6 500 U V rms 1000 pF 0.047 µF 0.022 µF 0.1 µF 0.22 µF 0.47 µF 470 pF 220 pF 100 pF 2200 pF 4700 pF 0.01µF 2000VDC f Hz 10 2 5 10 2 5 10 2 5 103 4 5 6 550 U V rms 0.047 µF 0.1 µF 0.15 µF 0.022 µF 4700 pF 2200 pF 1000 pF 470 pF 220 pF 100 pF 0.01 µF WIMA FKP 4 Continuation WIMA MKP 10 Technical information and general data see page 72. Permissible AC voltage in relation to frequency at 10 ) C internal temperature rise (general guide). Continuation page 71

1 1.08 D Recommendation for Processing and Application of Through-Hole Capacitors Soldering Process A preheating of through-hole WIMA capacitors is allowed for temperatures Tmax  100 ° C. In practice a preheating duration of t  5 min. has been proven to be best. Single wave soldering S oldering bath temperature: T  260 ° C Immersion time: t  5 sec Double wave soldering S oldering bath temperature: T  260 ° C Immersion time: 2 x t  3 sec Due to different soldering processes and heat requirements the graphs are to be regarded as a recommendation only. 2 s 3 s 30 60 90 120 150 180 210 240 sec] [ t T 260 240 220 200 180 160 140 120 100 [°C] 10 s see detail- enlargement Wave soldering Typical temperature/time graph for double wave soldering WIMA Quality and Environmental Philosophy ISO 9001:2000 Certification ISO 9001:2000 is an international basic standard of quality assurance systems for all branches of industry. The approval according to ISO 9001:2000 of our factories by the VDE inspectorate certifies that organisation, equipment and moni- toring of quality assurance in our factories correspond to internationally recognized standards. WIMA WPCS The WIMA Process Control System (WPCS) is a quality surveillance and optimization system developed by WIMA. WPCS is a major part of the quality-oriented WIMA production. Points of application of WPCS during production process: ” incoming material inspection ” metallization ” film inspection ” schoopage ” pre-healing ” lead attachment ” cast resin preparation/ e ncapsulation ” 100% final inspection ” AQL check WIMA Environmental Policy All WIMA capacitors, irrespective of whether through-hole devices or SMD, are made of environmentally friendly materials. Neither during manufacture nor in the product itself any toxic substances are used, e.g. Lead – PBB/PBDE PCB – Arsenic CFC – Cadmium Hydrocarbon chloride – Mercury Chromium 6+ – etc. We merely use pure, recyclable materials for packing our components, such as: ” carton ” cardboard ” adhesive tape made of paper ” polystyrene We almost completely refrain from using packing materials such as: ” foamed polystyrene (Styropor®) ” adhesive tapes made of plastic ” metal clips RoHS Compliance According to the RoHS Directive 2002/95/EC certain hazardous substances like e.g. lead, cadmium, mercury must not be used any longer in electronic equipment as of July 1st, 2006. For the sake of the environment WIMA has refraind from using such substances since years already. Tape for lead-free WIMA capacitors DIN EN ISO 14001:2005 WIMA’s environmental management has been established in accordance with the guidelines of DIN EN ISO 14001:2005. The certification has been granted in June 2006.

1 1.08 D P P0P2 F d P H H d F t W Vh W P H H W W dF Diagram 1: PCM 2.5/5/7.5mm Diagram 3: PCM 22.5 and 27.5*mm *PCM 27.5 taping possible with two feed holes between components Diagram 2: PCM 10/15 mm Dimensions for Radial Taping Designation Symbol PCM 2.5 taping PCM 5 taping PCM 7.5 taping PCM 10 taping * P CM 15 taping * P CM 22.5 taping PCM 27.5 taping adhesive tape adhesive tape adhesive tape adhesive tape adhesive tape adhesive tape adhesive tape cumulative pitch cumulative pitch cumulative pitch cumulative pitch cumulative pitch cumulative pitch cumulative pitch t o lead c omponent centre Feed hole centre to top H1 H+Hcomponent < H 1 H+Hcomponent < H 1 H+Hcomponent < H 1 H+Hcomponent < H 1 H+Hcomponent < H 1 H+Hcomponent < H 1 H+Hcomponent < H 1 Lead spacing at F 2.5 p0.5 5.0 +0.8 u pper edge of carrier tape –0.2 T ROLL/AMMO AMMO Package v (see also page 122) U nit see details page 124. v Please give „H“ dimensions and desired packaging type when ordering. Dims in mm. „ Diameter of leads see General Data. Please clarify customer-specific deviations with the manufacturer. * P CM 10 and PCM 15 can be crimped to PCM 7.5. Position of components according to PCM 7.5 (sketch 1). P 0 = 12.7 or 15.0 is possible REEL P 360 max. B 52 p2 depending on P 30 p1 5 8 p2 comp. dimensions 52 p2 5 4 p2 depending REEL P 360 max. B 5 8 p2 or REEL P 500 max. B 6 0 p2 on PCM and P 30 p1 66 p2 P 25 p1 68 p2 component dimensions Typical Dimensions for Taping Configuration