MK3724 RENESAS | Alldatasheet

Document overview

  • Manufacturer or author: Provided By www.digicamel.com(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 9

Technical content

Features

  • Packaged in 16-pin TSSOP
  • Pb free packaging
  • Replaces a VCXO and oscillator
  • Operating voltage of 3.3 V
  • Provides output of 27 MHz plus audio clock
  • Uses an inexpensive 27 MHz pullable crystal
  • On-chip patented VCXO with pull range of 230 ppm (minimum)
  • VCXO tuning voltage of 0 to 3.3 V
  • Advanced, low power, sub-micron CMOS process
  • Industrial temperature range available
  • For other standard audio frequencies see the MK3722 Block Diagram Voltage Controlled Crystal Oscillator VIN

27 MHz

S2:S0 VDD GND PDTS

VCXO PLUS AUDIO CLOCK FOR STB VCXO AND SYNTHESIZER IDT™ VCXO PLUS AUDIO CLOCK FOR STB 2 MK3724 REV E 051310 Pin Assignment Pin Descriptions Audio Clock Select Table VDD NC VDD VIN VDD 27M GND GND GND ACLK PDTS 16-pin TSSOP S2 S1 S0 ACLK (MHz) 000 3 . 0 7 2 001 4 . 0 9 6 010 6 . 1 4 4 011 8 . 1 9 2 1 0 0 12.288 1 0 1 24.576 1 1 0 33.8688 1 1 1 73.728 Pin Number Pin Name Pin Type Pin Description 1 X2 Output Crystal connection. Connect to a 27 MHz fundamental mode pullable crystal. 2 X1 Input Crystal connection. Connect to a 27 MHz fundamental mode pullable crystal. 3 VDD Power Connect to +3.3 V. 4 VDD Power Connect to +3.3 V. 5 VIN Input Voltage input to VCXO. Changing the voltage between 0 to 3.3 V controls the VCXO frequency. 6 GND Power Connect to ground. 7 GND Power Connect to ground. 8P D T S Power Power Down Tri-state. This pin powers down entire chip and tri-states the outputs when low. Internal pull-up resistor. 9 S2 Input Select input S2. Selects ACLK per table above. Internal pull-up resistor. 10 ACLK Output Audio clock output per table above. 11 GND Power Connect to ground. 12 27M Output 27 MHz reference clock output. 13 S0 Input Select input S0. Selects ACLK per table above. Internal pull-up resistor. 14 VDD Power Connect to +3.3 V. 15 NC -- No connect. Do not connect anything to this pin. 16 S1 Input Select input S1. Selects ACLK per table above. Internal pull-up resistor.

VCXO PLUS AUDIO CLOCK FOR STB VCXO AND SYNTHESIZER IDT™ VCXO PLUS AUDIO CLOCK FOR STB 3 MK3724 REV E 051310 External Component Selection The MK3724 requires a minimum number of external components for proper operation. Decoupling Capacitors Decoupling capacitors of 0.01 µF should be connected between VDD and GND on pins 3 and 4, pins 6 and 7, and pins 11 and 14 as close to the MK3724 as possible. For optimum device performance, the decoupling capacitors should be mounted on the component side of the PCB. Avoid the use of vias in the decoupling circuit. Series Termination Resistor When the PCB traces between the clock outputs and the loads are over 1 inch, series termination should be used. To series terminate a 50 Ω trace (a commonly used trace impedance), place a 33 Ω resistor in series with the clock line, as close to the clock output pin as possible. The nominal impedance of the clock output is 20 Ω. Quartz Crystal The MK3724 VCXO function consists of the external crystal and the integrated VCXO oscillator circuit. To assure the best system performance (frequency pull range) and reliability, a crystal device meeting IDT’ recommended parameters must be used, and the layout guidelines discussed in the following section must be followed. See Application Note MAN05 for a full list of crystal parameters. The frequency of oscillation of a quartz crystal is determined by its “cut” and by the load capacitors connected to it. The MK3724 incorporates on-chip variable load capacitors that “pull” (change) the frequency of the crystal. The crystal specified for use with the MK3724 is designed to have zero frequency error when the total of on-chip + stray capacitance is 14 pF . The external crystal must be connected as close to the chip as possible and should be on the same side of the PCB as the MK3724. There should be no via’s between the crystal pins and the X1 and X2 device pins. There should be no signal traces underneath or close to the crystal. Crystal Tuning Load Capacitors The crystal traces should include pads for small fixed capacitors, one between X1 and ground, and another between X2 and ground. Stuffing of these capacitors on the PCB is optional. The need for these capacitors is determined at system prototype evaluation, and is influenced by the particular crystal used (manufacture and frequency) and by PCB layout. The typical required capacitor value is 1 to 4 pF . To determine the need for and value of the crystal adjustment capacitors, you will need a PC board of your final layout, a frequency counter capable of about 1 ppm resolution and accuracy, two power supplies, and samples of the crystals which you plan to use in production. Y ou will also need measured initial accuracy for each crystal at the specified crystal load capacitance (C L). To determine the value of the crystal capacitors: 1. Con nect VDD to 3.3 V. Connect pin 5 to the second power supply. Adjust the voltage on pin 5 to 0V. Measure and record the frequency of the CLK output. 2. Adjust the voltage on pin 5 to 3.3 V. Measure and record the frequency of the same output. To calculate the centering error: Where: ftarget = nominal crystal frequency errorxtal =actual initial accuracy (in ppm) of the crystal being measured If the centering error is less than ±25 ppm, no adjustment is needed. If the centering error is more than 25 ppm negative, the PC board has excessive stray capacitance and a new PCB layout should be considered to reduce stray capacitance. (Alternately, the crystal may be re-specified to a higher load capacitance. Contact IDT for details.) If the centering error is more than 25 ppm positive, add identical fixed centering capacitors from each crystal pin to ground. The value for each of these caps (in pF) is given by: Error 10 6x f3.3 3.0() V fte targ–() f0V fte targ–()+ fte targ

VCXO PLUS AUDIO CLOCK FOR STB VCXO AND SYNTHESIZER IDT™ VCXO PLUS AUDIO CLOCK FOR STB 4 MK3724 REV E 051310 External Capacitor = 2 x (centering error)/(trim sensitivity) Trim sensitivity is a parameter which can be supplied by your crystal vendor. If you do not know the value, assume it is 30 ppm/pF . After any changes, repeat the measurement to verify that the remaining error is acceptably low (typically less than ±25 ppm). Absolute Maximum Ratings Stresses above the ratings listed below can cause permanent damage to the MK3724. These ratings, which are standard values for IDT commercially rated parts, are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical parameters are guaranteed only over the recommended operating temperature range. Recommended Operation Conditions VDD=3.3 V ±5% , Ambient temperature -40 to +85° C, unless stated otherwise Item Rating Supply Voltage, VDD 7 V All Inputs and Outputs -0.5 V to VDD+0.5 V Ambient Operating Temperature, Commercial 0 to +70 ° C Ambient Operating Temperature, Industrial -40 to +85 ° C Storage Temperature -65 to +150 ° C Soldering Temperature 260 ° C Parameter Min. Typ. Max. Units Ambient Operating Temperature, Commercial 0 +70 ° C Ambient Operating Temperature, Industrial -40 +85 ° C Power Supply Voltage (measured in respect to GND) +3.135 +3.465 V Reference crystal parameters Refer to page 3 Parameter Symbol Conditions Min. Typ. Max. Units Operating Voltage VDD 3.135 3.465 V Output High Voltage V OH IOH = -12 mA 2.4 V Output Low Voltage V OL IOL = 12 mA 0.4 V Output High Voltage (CMOS Level) VOH IOH = -4 mA VDD-0.4 V Output Low Voltage (CMOS Level) VOL IOH = +4 mA 0.375 V Input High Voltage (S1:S0) V IH 2.0 V

VCXO PLUS AUDIO CLOCK FOR STB VCXO AND SYNTHESIZER IDT™ VCXO PLUS AUDIO CLOCK FOR STB 5 MK3724 REV E 051310 VDD = 3.3 V ±5%, Ambient Temperature -40 to +85° C, unless stated otherwise Note 1: External crystal device must conform with Pullable Crystal Specifications listed on page 3. Input High Voltage (S2) VIH 2.5 V Input Low Voltage (S1:S0) V IL 0.8 V Input Low Voltage (S2) V IL 0.5 V Input High Current I IH at 3.3V, Sx, PDTS 0.1 µA Input Low Current I IL at 0V, Sx, PDTS -8.5 µA Operating Supply Current IDD No load 11 mA Short Circuit Current I OS ±50 mA VIN, VCXO Control Voltage V IA 03 .3 V On Chip Pull-up Resistor, inputs RPU Input selects 360 kΩ Input Capacitance CIN Input selects 5 pF Nominal Output Impedance Z OUT 20 Ω Parameter Symbol Conditions Min. Typ. Max. Units Crystal Pullability fP 0V< VIN < 3.3 V, Note 1 + 100 + 150 ppm V CXO Gain VIN = VDD/2 + 1 V, Note 1 150 ppm/V Output Rise Time tOR 20% to 80%, CL=15 pF 1.2 2.0 ns Output Fall Time tOF 80% to 20%, CL=15 pF 1.2 2.0 ns Output Clock Duty Cycle t D Measured at 1.65 V, CL=15 pF 40 50 60 % Maximum Output Jitter, short term t J CL=15 pF +150 ps Changing Frequency Setting Time 1m s Power-up time PLL lock time from power-up up to ±1% of final frequency 10 ms PDTS goes high until stable CLK output up to 1% of final frequency 2m s Parameter Symbol Conditions Min. Typ. Max. Units

VCXO PLUS AUDIO CLOCK FOR STB VCXO AND SYNTHESIZER IDT™ VCXO PLUS AUDIO CLOCK FOR STB 6 MK3724 REV E 051310 Thermal Characteristics Notes: 2. YYWW is the last two digits of the year, and the week number that the part was assembled. 3. “L ” designates Pb (lead) free. 4. Bottom mark denotes country of origin if not USA. Parameter Symbol Conditions Min. Typ. Max. Units Thermal Resistance Junction to Ambient θJA Still air 78 ° C/W θJA 1 m/s air flow 70 ° C/W θJA 3 m/s air flow 68 ° C/W Thermal Resistance Junction to Case θJC 37 ° C/W 1 8 916 MK3724GL YYWW 1 8 916 MK3724IL YYWW

VCXO PLUS AUDIO CLOCK FOR STB VCXO AND SYNTHESIZER IDT™ VCXO PLUS AUDIO CLOCK FOR STB 7 MK3724 REV E 051310 Package Outline and Package Dimensions (16-pin TSSOP, 4.40 mm Body, 0.65 mm Pitch) Package dimensions are kept current with JEDEC Publication No. 95Ordering Information While the information presented herein has been checked for both accuracy and reliability, Integrated Device Technology (IDT) assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by IDT. IDT reserves the right to change any circuitry or specifications without notice. IDT does not authorize or warrant any IDT product for use in life support devices or critical medical instruments. Part / Order Number Marking Shipping Packaging Package Temperature MK3724GLF see page 6 Tubes 16-pin TSSOP 0 to +70 ° C MK3724GLFTR Tape and Reel 16-pin TSSOP 0 to +70 ° C MK3724GILF Tubes 16-pin TSSOP -40 to +85 ° C MK3724GILFTR Tape and Reel 16-pin TSSOP -40 to +85 ° C INDEX AREA 1 2 D E1 E SEATING PLANE A AA e - C - b .10 (.004) C c L Millimeters Inches Symbol Min Max Min Max A- - 1 . 2 0 - - 0 . 0 4 7 A1 0.05 0.15 0.002 0.006 A2 0.80 1.05 0.032 0.041 b 0.19 0.30 0.007 0.012 C 0.09 0.20 0.0035 0.008 D 4.90 5.1 0.193 0.201 E 6.40 BASIC 0.252 BASIC E1 4.30 4.50 0.169 0.177 e 0.65 Basic 0.0256 Basic L 0.45 0.75 0.018 0.030 α 0° 8° 0° 8°

© 2006 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names a nd marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA Corporate Headquarters Integrated Device Technology, Inc. www.idt.com For Sales 800-345-7015 408-284-8200 Fax: 408-284-2775 For Tech Support www.idt.com/go/clockhelp Innovate with IDT and accelerate your future networks. Contact: www.IDT.com MK3724 VCXO PLUS AUDIO CLOCK FOR STB VCXO AND SYNTHESIZER

© 202 Renesas Electronics Corporation. All rights reserved. IMPORTANT NOTICE AND DISCLAIMER RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. Renesas grants you permission to use these resources only for development of an application that uses Renesas products. Other reproduction or use of these resources is strictly prohibited. No license is granted to any other Renesas intellectual property or to any third party intellectual property. Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims, damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use o any Renesas resources expands or otherwise alters any applicable warranties or warranty disclaimers for these products. ('LVFODLPHURev.1.0 Mar 2020) Corporate Headquarters Contact Information TOYOSU FORESIA, 3-2-24 Toyosu, For further information on a product, technology, the most Koto-ku, Tokyo 135-0061, Japan up-to-date version of a document, or your nearest sales www.renesas.com office, please visit: www.renesas.com/contact/ Trademarks Renesas and the Renesas logo are trademarks of Renesas Electronics Corporation. All trademarks and registered trademarks are the property of their respective owners.