DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 28
Technical content
Features
- High-Accuracy Charge Voltage: ±0.75% over –5°C to + 60°C (Li-ion charging temperature range)
- Zero Off-Mode Current
- 10 µA Reverse Leakage
- Ultra-Low 380 mV Dropout at 500 mA
- Wide Input Voltage Range
- Logic-Controlled Enable Input (8-Lead Devices Only)
- Thermal Shutdown and Current-Limit Protection
- Power MSOP-8, Power SOIC-8, and SOT-223 Packages
- Pulse Charging Capability
Applications
- Li-Ion Battery Charger
- Cellular Phones
- Palmtop Computers
- PDAs
- Self-Charging Battery Packs General Description The MIC79050 is a simple single-cell lithium-ion battery charger. It includes an on-chip pass transistor for high precision charging. Featuring ultra-high precision (±0.75% over the Li-ion battery charging temperature range) and “zero” off-mode current, the MIC79050 provides a very simple, cost effective solution for charging lithium-ion battery. Other features of the MIC79050 include current-limit and thermal shutdown protection. In the event the input voltage to the charger is disconnected, the MIC79050 also provides minimal reverse-current and reversed-battery protection. The MIC79050 is a fixed 4.2V device and comes in the thermally-enhanced MSOP-8, SOIC-8, and SOT-223 packages. The 8-lead versions also come equipped with enable and feedback inputs. All versions are specified over the temperature range of –40°C to +125°C. Package Types MIC79050 3-Lead SOT-223 (S) IN BATGND 13 2 TAB GND MIC79050 8-Lead SOIC/MSOP (M/MM) GND GND GND GND EN IN BAT FB Simple Lithium-Ion Battery Charger
DS20005771B-page 2 2017 - 2022 Microchip Technology Inc. and its subsidiaries. Typical Application Circuits Functional Block Diagrams Li-Ion Cell 4.2V 0.75% over Temp IN BAT GND MIC79050-4.2YSRegulated or unregulated wall adapter 4.2V 0.75% Li-Ion Cell IN BAT FB GND EN MIC79050-4.2YMM External PWM* *See Applications Information Regulated or unregulated wall adapter Simplest Battery Charging Solution Pulse-Charging Application Current Limit Thermal Shutdown IN GND Bandgap Ref. VBAT VIN MIC79050-4.2YS 3-Lead Version IN EN FB GND VREF Bandgap Ref. Current Limit Thermal Shutdown VBAT VIN MIC79050-4.2YM/YMM 8-Lead Version
2017 - 2022 Microchip Technology Inc. and its subsidiaries. DS20005771B-page 3 MIC79050
1.0 ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings † Operating Ratings ‡ † Notice: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational sections of this specification is not intended. Exposure to maximum rating conditions for extended periods may affect device reliability. ‡ Notice: The device is not guaranteed to function outside its operating ratings. Note 1:The maximum allowable power dissipation at any TA (ambient temperature) is calculated using: PD(max) = (TJ(max) – TA) ÷ θJA. Exceeding the maximum allowable power dissipation will result in excessive die tem - perature, and the regulator will go into thermal shutdown.
ELECTRICAL CHARACTERISTICS
Electrical Characteristics: VIN = VBAT + 1.0V; COUT = 4.7 μF, IOUT = 100 μA; TJ = +25°C, bold values indicate –40°C ≤ TJ ≤ +125°C; unless noted. Parameter Symbol Min. Typ. Max. Units Conditions Battery Voltage Accuracy V BAT –0.75 — 0.75 % Variation from nominal VOUT, –5°C to +60°C Battery Voltage Temperature Coefficient ΔVBAT/ ΔT — 40 — ppm/°C Note 1 Line Regulation ΔVBAT/ VBAT — 0.009 0.05 %/V V IN = VBAT + 1V to 16V— — 0.1 Load Regulation ΔVBAT/ VBAT — 0.05 0.5 % I OUT = 100 μA to 500 mA, Note 2— — 0.7 Dropout Voltage (Note 3) VIN – VBAT — 380 500 mV I OUT = 500 mA— — 600 Ground Pin Current (Note 4, Note 5) IGND — 85 130 µA V EN ≥ 3.0V, IOUT = 100 μA— — 170 — 11 20 mA V EN ≥ 3.0V, IOUT = 500 mA— — 25 Ground Pin Quiescent Current (Note 5) IGND — 0.05 3 µA VEN ≤ 0.4V (shutdown) — 0.10 8 VEN ≤ 0.18V (shutdown) Ripple Rejection PSRR — 75 — dB f = 120 Hz Current Limit ILIMIT — 750 900 mA V BAT = 0V— — 1000 Thermal Regulation ΔVBAT/ ΔPD — 0.05 — %/W Note 6 ENABLE Input Enable Input Logic-Low Voltage VENL — 0.4 — V VEN = logic-low (shutdown)— — 0.18 2.0 — — VEN = logic-high (enabled)
DS20005771B-page 4 2017 - 2022 Microchip Technology Inc. and its subsidiaries. Enable Input Current IENL — 0.01 –1 µA VENL ≤ 0.4V (shutdown) — 0.01 –2 VENL ≤ 0.18V (shutdown) — IENH — 5 20 µA V ENH ≥ 2.0V (enabled)— — 25 Note 1: Battery voltage temperature coefficient is the worst case voltage change divided by the total temperature range. 2: Regulation is measured at constant junction temperature using low duty cycle pulse testing. Parts are tested for load regulation in the load range from 100 μA to 500 mA. Changes in output voltage due to heat- ing effects are covered by the thermal regulation specification. 3: Dropout voltage is defined as the input to battery output differential at which the battery voltage drops 2% below its nominal value measured at 1V differential. 4: Ground pin current is the charger quiescent current plus pass transistor base current. The total current drawn from the supply is the sum of the load current plus the ground pin current. 5: VEN is the voltage externally applied to devices with the EN (enable) input pin. MSOP-8 (MM) and SOIC-8 (M) packages only. 6: Thermal regulation is the change in battery voltage at a time “t” after a change in power dissipation is applied, excluding load or line regulation effects. Specifications are for a 500 mA load pulse at VIN = 16V for t = 10 ms. ELECTRICAL CHARACTERISTICS (CONTINUED) Electrical Characteristics: VIN = VBAT + 1.0V; COUT = 4.7 μF, IOUT = 100 μA; TJ = +25°C, bold values indicate –40°C ≤ TJ ≤ +125°C; unless noted. Parameter Symbol Min. Typ. Max. Units Conditions
2017 - 2022 Microchip Technology Inc. and its subsidiaries. DS20005771B-page 5 MIC79050 TEMPERATURE SPECIFICATIONS (Note 1) Parameters Sym. Min. Typ. Max. Units Conditions Temperature Ranges Junction Operating Temperature Range TJ –40 — +125 °C — Storage Temperature Range TS –65 — +150 °C — Lead Temperature — — — +260 °C Soldering, 5s Package Thermal Resistances (Note 2) Thermal Resistance MSOP-8 JA — 80 — °C/W — Thermal Resistance SOIC-8 JA — 63 — °C/W — Thermal Resistance SOT-223 JC — 15 — °C/W — JA — 62 — °C/W — Note 1: The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable junction temperature and the thermal resistance from junction to air (i.e., TA, TJ, JA). Exceeding the maximum allowable power dissipation will cause the device operating junction temperature to exceed the maximum +125°C rating. Sustained junction temperatures above +125°C can impact the device reliability. 2: The maximum allowable power dissipation at any TA (ambient temperature) is calculated using: PD(max) = (TJ(max) – TA) ÷ θJA. Exceeding the maximum allowable power dissipation will result in excessive die tem- perature, and the regulator will go into thermal shutdown.
DS20005771B-page 6 2017 - 2022 Microchip Technology Inc. and its subsidiaries.
2.0 TYPICAL PERFORMANCE CURVES
FIGURE 2-1: Dropout Voltage vs. Output Current. FIGURE 2-2: Dropout Voltage vs. Temperature. FIGURE 2-3: Dropout Characteristics. FIGURE 2-4: Dropout Characteristics. FIGURE 2-5: Output Current vs. Ground Current. FIGURE 2-6: Ground Current vs. Supply Voltage. Note: The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore outside the warranted range. 100 200 300 400 0 100 200 300 400 500 DROPOUT VOLTAGE (mV) OUTPUT CURRENT (mA) 100 200 300 400 500 600 -40 0 40 80 120 DROPOUT VOLTAGE (mV) TEMPERATURE (°C) 0246 8 1 0 1 2 1 4 1 6OUTPUT VOLTAGE (V) INPUT VOLTAGE (V) 50mA,150mA 5mA 0246OUTPUT VOLTAGE (V) INPUT VOLTAGE (V) 250mA 500mA 0 100 200 300 400 500 GROUND CURRENT (mA) OUTPUT CURRENT (mA) 0.5 1.5 0 4 8 12 16 GROUND CURRENT (mA) SUPPLY VOLTAGE (V) 50mA 5mA
2017 - 2022 Microchip Technology Inc. and its subsidiaries. DS20005771B-page 9 MIC79050
3.0 PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 3-1. TABLE 3-1: PIN FUNCTION TABLE Pin Number SOT-223 Pin Number SOIC-8, MSOP-8 Pin Name Description 1 2 IN Supply input. 2, TAB 5, 6, 7, 8 GND Ground: SOT-223 pin 2 and TAB are internally connected. SOIC-8 pins 5 through 8 are internally connected. 3 3 BAT Battery voltage output. — 1 EN Enable (Input): TTL/CMOS-compatible control input. Logic-high = enable; logic-low or open = shutdown. — 4 FB Feedback node.
DS20005771B-page 10 2017 - 2022 Microchip Technology Inc. and its subsidiaries.
4.0 FUNCTIONAL DESCRIPTION
The MIC79050 is a high-accuracy, linear battery charging circuit designed for the simplest implementation of a single lithium-ion (Li-ion) battery charger. The part can operate from a regulated or unregulated power source, making it ideal for various applications. The MIC79050 can take an unregulated voltage source and provide an extremely accurate termination voltage. The output voltage varies only 0.75% from nominal over the standard temperature range for Li-ion battery charging (–5°C to +60°C). With a minimum of external components, an accurate constant-current charger can be designed to provide constant-current, constant-voltage charging for Li-ion cells.
4.1 Input Voltage
The MIC79050 can operate with an input voltage up to 16V (20V absolute maximum), ideal for applications where the input voltage can float high, such as an unregulated wall adapter that obeys a load-line. Higher voltages can be sustained without any performance degradation to the output voltage. The line regulation of the device is typically 0.009%/V; that is, a 10V change on the input voltage corresponds to a 0.09% change in output voltage.
4.2 Enable
The MIC79050 has an enable pin that allows the charger to be disabled when the battery is fully charged and the current drawn by the battery has approached a minimum and/or the maximum charging time has timed out. When disabled, the regulator output sinks a minimum of current with the battery voltage applied directly onto the output. This current is typically 12 μA or less.
4.3 Feedback
The feedback pin allows for external manipulation of the control loop. This node is connected to an external resistive divider network, which is connected to the internal error amplifier. This amplifier compares the voltage at the feedback pin to an internal voltage reference. The loop then corrects for changes in load current or input voltage by monitoring the output voltage and linearly controlling the drive to the large, PNP pass element. By externally controlling the voltage at the feedback pin the output can be disabled or forced to the input voltage. Pulling and holding the feedback pin low forces the output low. Holding the feedback pin high forces the pass element into saturation, where the output will be the input minus the saturation (dropout) voltage.
4.4 Battery Output
The BAT pin is the output of the MIC79050 and connects directly to the cell to provide charging current and voltage. When the input is left floating or grounded, the BAT pin limits reverse current to <12 μA to minimize battery drain.
2017 - 2022 Microchip Technology Inc. and its subsidiaries. DS20005771B-page 11 MIC79050
5.0 APPLICATIONS INFORMATION
5.1 Simple Lithium-Ion Battery
Figure 5-1 shows a simple, complete lithium-ion battery charger. The charging circuit comprises of a cheap wall adapter, with a load-line characteristic. This characteristic is always present with cheap adapters due to the internal impedance of the transformer windings. The load-line of the unregulated output should be less than 4.4V to 4.6V at somewhere between 0.5C to 1C of the battery under charge. This 4.4 to 4.6V value is an approximate number based on the headroom needed above 4.2V for the MIC79050 to operate correctly. In other words, for a 500 mAh battery, the output of the semi-regulated supply should be between 225 mA to 500 mA (0.5C to 1C). If it is below 225 mA no damage will occur but the battery will take longer to charge. Figure 5-2 shows a typical wall adapter characteristic with an output current of 350 mA at 4.5V. This natural impedance of the wall adapter will limit the maximum current into the battery, so no external circuitry is needed to accomplish this. If extra impedance is needed to achieve the desired load-line, extra resistance can easily be added in series with the MIC79050 IN pin. FIGURE 5-1: Load-Line Charger with End-of-Charge Termination Circuit. FIGURE 5-2: Load-Line Characteristics of AC Wall Adapter.
5.2 The Charging Cycle
See Figure 5-3. State A: Initial charge. Here the battery’s charging current is limited by the wall adapter’s natural impedance. The battery voltage approaches 4.2V. State B: Constant voltage charge. Here the battery voltage is at 4.2V ±0.75% and the current is decaying in the battery. When the battery has reached approximately 1/10th of its 1C rating, the battery is considered to have reached full charge. Because of the natural characteristic impedance of the cheap wall adapters, as the battery current decreases so the input voltage increases. The MIC6270 and the LM4041 are configured as a simple voltage monitor, indicating when the input voltage has reached such a level so the current in the battery is low, indicating full charge. State C: End of charge cycle. When the input voltage, VS reaches VEOC, an end of charge signal is indicated. State D: Top up charge. As soon as enough current is drawn out of the input source, which pulls the voltage lower than the V EOC, the end of charge flag will be pulled low and charging will initiate. Variations on this scheme can be implemented, such as the circuit shown in Figure 5-4. For those designs that have a zero impedance source, see Figure 5-5. LM4041 CIM3-1.2 IN BAT FB GND EN MIC79050-4.2YM VEOC = VREF (1+ ) Impedance AC Load-line Wall Adapter 10k 4.7μF End of Charge MIC6270 VS VREF = 1.225V 0 0.2 0.4 0.6 0.8 SOURCE VOLTAGE (V) SOURCE CURRENT (A)
DS20005771B-page 12 2017 - 2022 Microchip Technology Inc. and its subsidiaries. FIGURE 5-3: Charging Cycles. FIGURE 5-4: Protected Constant-Current Charger.
5.3 Protected Constant-Current
Another form of charging is using a simple wall adapter that offers a fixed voltage at a controlled, maximum current rating. The output of a typical charger will source a fixed voltage at a maximum current unless that maximum current is exceeded. In the event that the maximum current is exceeded, the voltage will drop while maintaining that maximum current. Using an MIC79050 after this type of charger is ideal for lithium-ion battery charging. The only obstacle is end of charger termination. Using a simple differential amplifier and a similar comparator and reference circuit, similar to Figure 5-1, completes a single cell lithium-ion battery charger solution. Figure 5-4 shows this solution in completion. The source is a fixed 5V source capable of a maximum of 400 mA of current. When the battery demands full current (fast charge), the source will provide only 400 mA and the input will be pulled down. The output of the MIC79050 will follow the input minus a small voltage drop. When the battery approaches full charge, the current will taper off. As the current across R S approaches 50 mA, the output of the differential amplifier (MIC7300) will approach 1.225V, the reference voltage set by the LM4041. When it drops below the reference voltage, the output of the comparator (MIC6270) will allow the base of Q1 to be pulled high through R2. VEOC Open Circuit Charger Voltage Battery Current (IB) Battery Voltage (VB) Unregulated Input Voltage(VB)
79050 Programmed
(No LoadVoltage ) End of Charge (VEOC) State A Initial Charge State B Voltage Charge State C End of Charge State D Charge Top State C IN BAT FB GND EN MIC79050-4.2YM LM4041 CIM3-1.2 5V 5%@ 400mA 5% 4.7μF 8.06M 47k 47k 10k MIC6270 MIC7300 10k1k Li-Ion Cell
2017 - 2022 Microchip Technology Inc. and its subsidiaries. DS20005771B-page 13 MIC79050
5.4 Zero-Output Impedance Source
Input voltage sources that have very low output impedances can be a challenge due to the nature of the source. Using the circuit in Figure 5-5 will provide a constant-current and constant voltage charging algorithm with the appropriate end-of-charge termination. The main loop consists of an op-amp controlling the feedback pin through the schottky diode, D1. The charge current through RS is held constant by the op-amp circuit until the output draws less than the set charge-current. At this point, the output goes constant-voltage. When the current through RS gets to less than 50 mA, the difference amp output becomes less than the reference voltage of the MIC834 and the output pulls low. This sets the output of the MIC79050 less than nominal, stopping current flow and terminating charge. FIGURE 5-5: Zero-Output Impedance Source Charging.
5.5 Lithium-Ion Battery Charging
Single lithium-ion cells are typically charged by providing a constant current and terminating the charge with constant voltage. The charge cycle must be initiated by ensuring that the battery is not in deep discharge. If the battery voltage is below 2.5V, it is commonly recommended to trickle charge the battery with 5 mA to 10 mA of current until the output is above 2.5V. At this point, the battery can be charged with constant current until it reaches its top off voltage (4.2V for a typical single lithium-ion cell) or a time-out occurs. For the constant-voltage portion of the charging circuit, an extremely accurate termination voltage is highly recommended. The higher the accuracy of the termination circuit, the more energy the battery will store. Because lithium-ion cells do not exhibit a memory effect, less accurate termination does not harm the cell, but simply stores less usable energy in the battery. The charge cycle is completed by disabling the charge circuit after the termination current drops below a minimum recommended level, typically 50 mA or less, depending on the manufacturer’s recommendation, or if the circuit times out.
5.6 Time-Out
The time-out aspect of lithium-ion battery charging can be added as a safety feature of the circuit. Often times this function is incorporated in the software portion of an application using a real-time clock to count out the maximum amount of time allowed in the charging cycle. When the maximum recommended charge time for the specific cell has been exceeded, the enable pin of the MIC79050 can be pulled low, and the output will float to the battery voltage, no longer providing current to the output. As a second option, the feedback pin of the MIC79050 can be modulated as in Figure 5-6. It shows a simple circuit where the MIC834, an integrated comparator and reference, monitors the battery voltage and disables the MIC79050 output after the voltage on the battery exceeds a set value. When the voltage decays below this set threshold, the MIC834 drives Q1 low allowing the MIC79050 to turn on again and provide current to the battery until it is fully charged. This form of pulse charging is an acceptable way of maintaining the full charge on a cell until it is ready to be used. MIC79050-4.2YM MIC834 SD101 1/2 MIC7122 1/2 MIC7122 IN BAT FB GND EN 8.06M 4.7μF R2=124k R3=1k R4=124k 0.01μF VDD OUT GND INP R1=1k 221k 16.2k 16k 10k 5V RS ICC= 80mV RS IEOC= 1.24V × R1 R2 × RS LM4041 CIM3-1.2 Li-Ion Cell
DS20005771B-page 14 2017 - 2022 Microchip Technology Inc. and its subsidiaries. FIGURE 5-6: Pulse Charging for Top-Off Voltage.
5.7 Charging Rate
Lithium-ion cells are typically charged at rates that are fractional multiples of their rated capacity. The maximum varies between 1C and 1.3C (1× to 1.3× the capacity of the cell). The MIC79050 can be used for any cell size. The size of the cell and the current capability of the input source will determine the overall circuit charge rate. For example, a 1200 mAh battery charged with the MIC79050 can be charged at a maximum of 0.5C. There are no adverse effects to charging at lower charge rates; that charging will just take longer. Charging at rates greater than 1C are not recommended, nor do they decrease the charge time linearly. The MIC79050 is capable of providing 500 mA of current at its nominal rated output voltage of 4.2V. If the input is brought below the nominal output voltage, the output will follow the input, less the saturation voltage drop of the pass element. If the cell draws more than the maximum output current of the device, the output will be pulled low, charging the cell at 600 mA to 700 mA current. If the input is a fixed source with a low output impedance, this could lead to a large drop across the MIC79050 and excess heating. By driving the feedback pin with an external PWM circuit, the MIC79050 can be used to pulse charge the battery to reduce power dissipation and bring the device and the entire unit down to a lower operating temperature. Figure 5-7 and Figure 5-8 show typical configurations for PWM-based pulse-charging topologies. Figure 5-7 uses an external PWM signal to control the charger, while Figure 5-8 uses the MIC4417 as a low duty cycle oscillator to drive the base of Q1. Consult the battery manufacturer for optimal pulse-charging techniques. FIGURE 5-7: External PWM Circuit Design. FIGURE 5-8: PWM-Based Pulse Charging Using an MIC4417. Figure 5-9 shows another application to increase the output current capability of the MIC79050. By adding an external PNP power transistor, higher output current can be obtained while maintaining the same accuracy. The internal PNP now becomes the driver of a darlington array of PNP transistors, obtaining much higher output currents for applications where the charge rate of the battery is much higher. FIGURE 5-9: High-Current Charging.
5.8 Regulated Input Source Charging
When providing a constant-current, constant-voltage, charger solution from a well-regulated adapter circuit, the MIC79050 can be used with external components to provide a constant voltage, constant-current charger solution. Figure 5-10 shows a configuration for a high-side battery charger circuit that monitors input current to the battery and allows a constant current charge that is accurately terminated with the MIC79050. The circuit works best with smaller batteries, charging at C rates in the 300 mA to 500 mA range. The MIC7300 op-amp compares the drop across a current sense resistor and compares that to a high-side voltage reference, the LM4041, pulling the feedback pin low when the circuit is in the Li-Ion Cell IN BAT FB GND EN MIC79050-4.2YMM VDD OUT GND INP R1100k 4.7μF MIC834 VIN GND VREF=1.240V VBAT(low) = VREF (1+ )R1 Li-Ion Cell 4.7μF IN BAT FB GND EN MIC79050-4.2YMM VIN External PWM Li-Ion Cell 4.7μF 200pF 40k IN BAT FB GND EN MIC79050-4.2YMM VIN=4.5V to 16V MIC4417 IN BAT 4.7μFFB GND EN MIC79050-4.2YMM
2017 - 2022 Microchip Technology Inc. and its subsidiaries. DS20005771B-page 15 MIC79050 constant-current mode. When the current through the resistor drops and the battery gets closer to full charge, the output of the op-amp rises and allows the internal feedback network of the regulator take over, regulating the output to 4.2V. FIGURE 5-10: Constant-Current, Constant-Voltage Charger.
5.9 Simple Charging
The MIC79050 is available in a three-terminal package, allowing for extremely simple battery charging. When used with a current-limited, low-power input supply, the MIC79050-4.2YS completes a very simple, low-charge-rate, battery-charger circuit. It provides the accuracy required for termination, while a current-limited input supply offers the constant-current portion of the algorithm.
5.10 Thermal Considerations
The MIC79050 is offered in three packages for the various applications. The SOT-223 is most thermally efficient of the three packages, with the power SOIC-8 and the power MSOP-8 following suit.
5.10.1 POWER SOIC-8 THERMAL
One of the secrets of the MIC79050’s performance is its power SOIC-8 package that features half the thermal resistance of a standard SOIC-8 package. Lower thermal resistance means more output current or higher input voltage for a given package size. Lower thermal resistance is achieved by joining the four ground leads with the die attach paddle to create a single-piece electrical and thermal conductor. This concept has been used by MOSFET manufacturers for years, proving very reliable and cost effective for the user. Thermal resistance consists of two main elements, θJC, or thermal resistance junction to case and θCA, thermal resistance case to ambient ( Figure 5-11). θ JC is the resistance from the die to the leads of the package. θCA is the resistance from the leads to the ambient air and it includes θ CS, thermal resistance case to sink, and θSA, thermal resistance sink to ambient. Using the power SOIC-8 reduces the θJC dramatically and allows the user to reduce θ CA. The total thermal resistance, θJA, junction to ambient thermal resistance, is the limiting factor in calculating the maximum power dissipation capability of the device. Typically, the power SOIC-8 has a θJC of 20°C/W, this is significantly lower than the standard SOIC-8, which is typically 75°C/W. θCA is reduced because pins 5-8 can now be soldered directly to a ground plane, which significantly reduces the case to sink thermal resistance and sink to ambient thermal resistance. FIGURE 5-11: Thermal Resistance. The MIC79050 is rated to a maximum junction temperature of +125°C. It is important not to exceed this maximum junction temperature during operation of the device. To prevent this maximum junction temperature from being exceeded, the appropriate ground plane heat sink must be used. Figure 5-12 shows curves of copper area versus power dissipation, each trace corresponding to different temperature rises above ambient. From these curves, the minimum area of copper necessary for the part to operate safely can be determined. The maximum allowable temperature rise must be calculated to determine operation along which curve. FIGURE 5-12: Copper Area vs. Power SOIC Power Dissipation (ΔTJA). IN BAT FB GND EN MIC79050-4.2YMM SD101 4.7μF 0.01μF MIC7300 LM4041CIM3-1.2 16.2k 221k 10k RS I mV RCC S = =80 șJA șJC șCA Printed Circuit Board Ground Plane Heat Sink Area SOIC-8 AMBIENT 100 200 300 400 500 600 700 800 900 COPPER AREA (mm )2 POWER DISSIPATION (W) ¨TJA =
DS20005771B-page 16 2017 - 2022 Microchip Technology Inc. and its subsidiaries. ΔT is calculated by taking the maximum junction temperature and subtracting the maximum ambient operating temperature. For example, if the maximum ambient temperature is +40°C, the ΔT is determined as follows: EQUATION 5-1: Using Figure 5-12, the minimum amount of required copper can be determined based on the required power dissipation. Power dissipation in a linear regulator is calculated as follows: EQUATION 5-2: For example, using the charging circuit in Figure 5-10, assume the input is a fixed 5V and the output is pulled down to 4.2V at a charge current of 500 mA. The power dissipation in the MIC79050 is calculated as follows: EQUATION 5-3: From Figure 5-12, the minimum amount of copper required to operate this application at a ΔT of +85°C is less than 50 mm2.
5.10.2 QUICK METHOD
Determine the power dissipation requirements for the design along with the maximum ambient temperature at which the device will be operated. Refer to Figure 5-13, which shows safe operating curves for three different ambient temperatures: +25°C, +50°C, and +85°C. From these curves, the minimum amount of copper can be determined by knowing the maximum power dissipation required. If the maximum ambient temperature is +40°C and the power dissipation is as above, 0.46W, the curve in Figure 5-13 shows that the required area of copper is 50 mm2. The θJA of this package is ideally 63°C/W, but it will vary depending upon the availability of copper ground plane to which it is attached. FIGURE 5-13: Copper Area vs. Power SOIC Power Dissipation (TA).
5.10.3 POWER MSOP-8 THERMAL
The power MSOP-8 package follows the same idea as the power SOIC-8 package, using four ground leads with the die-attach paddle to create a single-piece electrical and thermal conductor, reducing thermal resistance and increasing power dissipation capability. The same method of determining the heat sink area used for the power SOIC-8 can be applied directly to the power MSOP-8. The same two curves showing power dissipation versus copper area are reproduced for the power-MSOP-8 and they can be applied identically.
5.10.4 QUICK METHOD
Determine the power dissipation requirements for the design along with the maximum ambient temperature at which the device will be operated. Refer to Figure 5-15, which shows safe operating curves for three different ambient temperatures, +25°C, +50°C, and +85°C. From these curves, the minimum amount of copper can be determined by knowing the maximum power dissipation required. If the maximum ambient temperature is +25°C and the power dissipation is 1W, the curve in Figure 5-15 shows that the required area of copper is 500 mm2, when using the power MSOP-8. PD VIN VOUT– IOUT VIN IGND+= 100 200 300 400 500 600 700 900 COPPER AREA (mm )2 POWER DISSIPATION (W) 85°C 50°C 25°C TJ = 125 °C
DS20005771B-page 18 2017 - 2022 Microchip Technology Inc. and its subsidiaries.
6.0 PACKAGING INFORMATION
6.1 Package Marking Information
X.XYNNNP 8-Lead SOIC* 3-Lead SOT-223* Example8-Lead MSOP* (front) 79050 4.2Y922P XXXXX -X.XY 79050 -4.2Y XXXXX -X.XXX WNNN 79050 -4.2YM 9722 Example8-Lead MSOP* (back) WNNN 9722 Legend: XX...X Product code or customer-specific information Y Year code (last digit of calendar year) YY Year code (last 2 digits of calendar year) WW Week code (week of January 1 is week ‘01’) NNN Alphanumeric traceability code Pb-free JEDEC ® designator for Matte Tin (Sn) * This package is Pb-free. The Pb-free JEDEC designator ( ) can be found on the outer packaging for this package.
- , ▲, ▼ Pin one index is identified by a dot, delta up, or delta down (triangle mark). Note: In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. Package may or may not include the corporate logo. Underbar (_) and/or Overbar (‾) symbol may not be to scale.
2017 - 2022 Microchip Technology Inc. and its subsidiaries. DS20005771B-page 19 MIC79050 3-Lead SOT-223 Package Outline and Recommended Land Pattern Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging.
DS20005771B-page 20 2017 - 2022 Microchip Technology Inc. and its subsidiaries. 8-Lead SOIC Package Outline and Recommended Land Pattern Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging.
2017 - 2022 Microchip Technology Inc. and its subsidiaries. DS20005771B-page 21 MIC79050 8-Lead MSOP Package Outline and Recommended Land Pattern Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging.
DS20005771B-page 22 2017 - 2022 Microchip Technology Inc. and its subsidiaries. NOTES:
2017 - 2022 Microchip Technology Inc. and its subsidiaries. DS20005771B-page 23 MIC79050 APPENDIX A: REVISION HISTORY Revision A (July 2017)
- Converted Micrel document MIC79050 to Micro- chip data sheet DS20005771A.
- Minor text changes throughout. Revision B (January 2022)
- Updated package marking drawing in Section 6.1 “Package Marking Information”.
DS20005771B-page 24 2017 - 2022 Microchip Technology Inc. and its subsidiaries. NOTES:
2017 - 2022 Microchip Technology Inc. and its subsidiaries. DS20005771B-page 25 MIC79050 PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, contact your local Microchip representative or sales office. Examples: a) MIC79050-4.2YS: Simple Lithium-Ion Battery Charger, 4.2V, –40°C to +125°C, 3-Lead SOT-223, 78/Tube b) MIC79050-4.2YS-TR: Simple Lithium-Ion Battery Charger, 4.2V, –40°C to +125°C, 3-Lead SOT-223, 2,500/Reel c) MIC79050-4.2YM: Simple Lithium-Ion Battery Charger, 4.2V, –40°C to +125°C, 8-Lead SOIC, 95/Tube d) MIC79050-4.2YM-TR: Simple Lithium-Ion Battery Charger, 4.2V, –40°C to +125°C, 8-Lead SOIC, 2,500/Reel e) MIC79050-4.2YMM: Simple Lithium-Ion Battery Charger, 4.2V, –40°C to +125°C, 8-Lead MSOP, 100/Tube f) MIC79050-4.2YMM-TR: Simple Lithium-Ion Battery Charger, 4.2V, –40°C to +125°C, 8-Lead MSOP, 2,500/Reel PART NO. XX PackageDevice Device: MIC79050: Simple Lithium-Ion Battery Charger Voltage: 4.2 = 4.2V Temperature: Y = –40°C to +125°C Package: S = 3-Lead SOT-223 M = 8-Lead SOIC MM = 8-Lead MSOP Media Type: <blank>= 78/Tube (SOT-223) <blank>= 95/Tube (SOIC) <blank>= 100/Tube (MSOP) TR = 2,500/Reel (All Packages) –X.X Voltage X Temperature Note 1: Tape and Reel identifier only appears in the catalog part number description. This identifier is used for ordering purposes and is not printed on the device package. Check with your Microchip Sales Office for package availability with the Tape and Reel option. –XX Media Type
DS20005771B-page 26 2017 - 2022 Microchip Technology Inc. and its subsidiaries. NOTES:
2017 - 2022 Microchip Technology Inc. and its subsidiaries. DS20005771B-page 27 This publication and the information herein may be used only with Microchip products, including to design, test, and integrate Microchip products with your application. Use of this informa- tion in any other manner violates these terms. Information regarding device applications is provided only for your conve- nience and may be superseded by updates. It is your responsi- bility to ensure that your application meets with your specifications. Contact your local Microchip sales office for additional support or, obtain additional support at https:// www.microchip.com/en-us/support/design-help/client-support- services. THIS INFORMATION IS PROVIDED BY MICROCHIP "AS IS". MICROCHIP MAKES NO REPRESENTATIONS OR WAR- RANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF NON- INFRINGEMENT, MERCHANTABILITY, AND FITNESS FOR A PARTICULAR PURPOSE, OR WARRANTIES RELATED TO ITS CONDITION, QUALITY, OR PERFORMANCE. IN NO EVENT WILL MICROCHIP BE LIABLE FOR ANY INDI- RECT, SPECIAL, PUNITIVE, INCIDENTAL, OR CONSE - QUENTIAL LOSS, DAMAGE, COST, OR EXPENSE OF ANY KIND WHATSOEVER RELATED TO THE INFORMATION OR ITS USE, HOWEVER CAUSED, EVEN IF MICROCHIP HAS BEEN ADVISED OF THE POSSIBILITY OR THE DAMAGES ARE FORESEEABLE. TO THE FULLEST EXTENT ALLOWED BY LAW, MICROCHIP'S TOTAL LIABILITY ON ALL CLAIMS IN ANY WAY RELATED TO THE INFORMATION OR ITS USE WILL NOT EXCEED THE AMOUNT OF FEES, IF ANY , THAT YOU HAVE PAID DIRECTLY TO MICROCHIP FOR THE INFORMATION. Use of Microchip devices in life support and/or safety applica- tions is entirely at the buyer's risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights unless otherwise stated. Trademarks The Microchip name and logo, the Microchip logo, Adaptec, AnyRate, AVR, AVR logo, AVR Freaks, BesTime, BitCloud, CryptoMemory, CryptoRF, dsPIC, flexPWR, HELDO, IGLOO, JukeBlox, KeeLoq, Kleer, LANCheck, LinkMD, maXStylus, maXTouch, MediaLB, megaAVR, Microsemi, Microsemi logo, MOST, MOST logo, MPLAB, OptoLyzer, PIC, picoPower, PICSTART, PIC32 logo, PolarFire, Prochip Designer, QTouch, SAM-BA, SenGenuity, SpyNIC, SST, SST Logo, SuperFlash, Symmetricom, SyncServer, Tachyon, TimeSource, tinyAVR, UNI/O, Vectron, and XMEGA are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. AgileSwitch, APT, ClockWorks, The Embedded Control Solutions Company, EtherSynch, Flashtec, Hyper Speed Control, HyperLight Load, IntelliMOS, Libero, motorBench, mTouch, Powermite 3, Precision Edge, ProASIC, ProASIC Plus, ProASIC Plus logo, Quiet- Wire, SmartFusion, SyncWorld, Temux, TimeCesium, TimeHub, TimePictra, TimeProvider, TrueTime, WinPath, and ZL are registered trademarks of Microchip Technology Incorporated in the U.S.A. Adjacent Key Suppression, AKS, Analog-for-the-Digital Age, Any Capacitor, AnyIn, AnyOut, Augmented Switching, BlueSky, BodyCom, CodeGuard, CryptoAuthentication, CryptoAutomotive, CryptoCompanion, CryptoController, dsPICDEM, dsPICDEM.net, Dynamic Average Matching, DAM, ECAN, Espresso T1S, EtherGREEN, GridTime, IdealBridge, In-Circuit Serial Programming, ICSP , INICnet, Intelligent Paralleling, Inter-Chip Connectivity, JitterBlocker, Knob-on-Display, maxCrypto, maxView, memBrain, Mindi, MiWi, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, MultiTRAK, NetDetach, NVM Express, NVMe, Omniscient Code Generation, PICDEM, PICDEM.net, PICkit, PICtail, PowerSmart, PureSilicon, QMatrix, REAL ICE, Ripple Blocker, RTAX, RTG4, SAM-ICE, Serial Quad I/O, simpleMAP , SimpliPHY, SmartBuffer, SmartHLS, SMART-I.S., storClad, SQI, SuperSwitcher, SuperSwitcher II, Switchtec, SynchroPHY , Total Endurance, TSHARC, USBCheck, VariSense, VectorBlox, VeriPHY , ViewSpan, WiperLock, XpressConnect, and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. The Adaptec logo, Frequency on Demand, Silicon Storage Technology, Symmcom, and Trusted Time are registered trademarks of Microchip Technology Inc. in other countries. GestIC is a registered trademark of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in other countries. All other trademarks mentioned herein are property of their respective companies. © 2017 - 2022, Microchip Technology Incorporated and its subsidiar- ies. All Rights Reserved. ISBN: 978-1-5224-9586-4 Note the following details of the code protection feature on Microchip products:
- Microchip products meet the specifications contained in their particular Microchip Data Sheet.
- Microchip believes that its family of products is secure when used in the intended manner, within operating specifications, and under normal conditions.
- Microchip values and aggressively protects its intellectual property rights. Attempts to breach the code protection features of Microchip product is strictly prohibited and may violate the Digital Millennium Copyright Act.
- Neither Microchip nor any other semiconductor manufacturer can guarantee the security of its code. Code protection does not mean that we are guaranteeing the product is “unbreakable”. Code protection is constantly evolving. Microchip is committed to continuously improving the code protection features of our products. For information regarding Microchip’s Quality Management Systems, please visit www.microchip.com/quality.
DS20005771B-page 28 2017 - 2017 - 2022 Microchip Technology Inc. and its subsidiaries. AMERICAS Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://www.microchip.com/ support Web Address: www.microchip.com Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Austin, TX Tel: 512-257-3370 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Novi, MI Tel: 248-848-4000 Houston, TX Tel: 281-894-5983 Indianapolis Noblesville, IN Tel: 317-773-8323 Fax: 317-773-5453 Tel: 317-536-2380 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Tel: 951-273-7800 Raleigh, NC Tel: 919-844-7510 New York, NY Tel: 631-435-6000 San Jose, CA Tel: 408-735-9110 Tel: 408-436-4270 Canada - Toronto Tel: 905-695-1980 Fax: 905-695-2078 ASIA/PACIFIC Australia - Sydney Tel: 61-2-9868-6733 China - Beijing Tel: 86-10-8569-7000 China - Chengdu Tel: 86-28-8665-5511 China - Chongqing Tel: 86-23-8980-9588 China - Dongguan Tel: 86-769-8702-9880 China - Guangzhou Tel: 86-20-8755-8029 China - Hangzhou Tel: 86-571-8792-8115 China - Hong Kong SAR Tel: 852-2943-5100 China - Nanjing Tel: 86-25-8473-2460 China - Qingdao Tel: 86-532-8502-7355 China - Shanghai Tel: 86-21-3326-8000 China - Shenyang Tel: 86-24-2334-2829 China - Shenzhen Tel: 86-755-8864-2200 China - Suzhou Tel: 86-186-6233-1526 China - Wuhan Tel: 86-27-5980-5300 China - Xian Tel: 86-29-8833-7252 China - Xiamen Tel: 86-592-2388138 China - Zhuhai Tel: 86-756-3210040 ASIA/PACIFIC India - Bangalore Tel: 91-80-3090-4444 India - New Delhi Tel: 91-11-4160-8631 India - Pune Tel: 91-20-4121-0141 Japan - Osaka Tel: 81-6-6152-7160 Japan - Tokyo Tel: 81-3-6880- 3770 Korea - Daegu Tel: 82-53-744-4301 Korea - Seoul Tel: 82-2-554-7200 Malaysia - Kuala Lumpur Tel: 60-3-7651-7906 Malaysia - Penang Tel: 60-4-227-8870 Philippines - Manila Tel: 63-2-634-9065 Singapore Tel: 65-6334-8870 Taiwan - Hsin Chu Tel: 886-3-577-8366 Taiwan - Kaohsiung Tel: 886-7-213-7830 Taiwan - Taipei Tel: 886-2-2508-8600 Thailand - Bangkok Tel: 66-2-694-1351 Vietnam - Ho Chi Minh Tel: 84-28-5448-2100 EUROPE Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4485-5910 Fax: 45-4485-2829 Finland - Espoo Tel: 358-9-4520-820 France - Paris Germany - Garching Tel: 49-8931-9700 Germany - Haan Tel: 49-2129-3766400 Germany - Heilbronn Tel: 49-7131-72400 Germany - Karlsruhe Tel: 49-721-625370 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Germany - Rosenheim Tel: 49-8031-354-560 Israel - Ra’anana Tel: 972-9-744-7705 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Italy - Padova Tel: 39-049-7625286 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Norway - Trondheim Tel: 47-7288-4388 Poland - Warsaw Tel: 48-22-3325737 Romania - Bucharest Tel: 40-21-407-87-50 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 Sweden - Gothenberg Tel: 46-31-704-60-40 Sweden - Stockholm Tel: 46-8-5090-4654 UK - Wokingham Tel: 44-118-921-5800 Fax: 44-118-921-5820 Worldwide Sales and Service 09/14/21