MIC7122

DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 22

Technical content

Features

• Small Footprint MSOP-8 Package
• 350 μA Supply Current per Op Amp at 2.2V Supply
• Guaranteed 2.2V, 5V, and 15V Performance
• 750 kHz Gain-Bandwidth Product at 2.2V Supply
• 0.01% Total Harmonic Distortion at 1 kHz (15V, 2 kΩ)
• Drives 200 pF at 5V and Greater Supply Voltages

Applications

• Battery-Powered Instrumentation
• PCMCIA, USB Peripherals
• Portable Computers and PDAs General Description The MIC7122 is a dual high-performance CMOS operational amplifier featuring rail-to-rail inputs and outputs. The input common-mode range extends beyond the rails by 300 mV, and the output voltage swings to within 150 μV of both rails when driving a 100 kΩ load. The amplifiers operate from 2.2V to 15V and are fully specified at 2.2V , 5V, and 15V. Gain bandwidth and slew rate are 750 kHz and 0.7 V/μs, respectively at a 2.2V supply The MIC7122 is available in an 8-lead MSOP package. Package Type MIC7122 MSOP-8 (MM) OUTB INB– INB+ OUTA INA– INA+ Pin Configuration Functional Pinout A B OUTB INB– INB+ OUTA INA– INA+ Rail-to-Rail Dual Op Amp

DS20006290A-page 2  2020 Microchip Technology Inc.

1.0 ELECTRICAL CHARACTERISTICS

Absolute Maximum Ratings † Operating Ratings ‡ † Notice: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational sections of this specification is not intended. Exposure to maximum rating conditions for extended periods may affect device reliability. ‡ Notice: The device is not guaranteed to function outside its operating ratings. Note 1: I/O Pin Voltage is any external voltage to which an input or output is referenced. 2: Devices are ESD sensitive. Handling precautions are recommended. Human body model, 1.5 kΩ in series with 100 pF.

DC ELECTRICAL CHARACTERISTICS (2.2V) VV+ = +2.2V, VV– = 0V, VCM = VOUT = VV+/2; RL = 1 MΩ; TJ = +25°C; Note 1. Parameters Sym. Min. Typ. Max. Units Conditions Input Offset Voltage VOS — 0.5 9 mV — Input Offset Voltage Average Drift TCVOS — 3.0 — μV/°C — Input Bias Current IB — 1.0 10 pA Input Offset Current IOS — 0.5 5 pA Input Resistance RIN — >1 — TΩ — Common-Mode Rejection Ratio CMRR 45 65 — dB –0.3V ≤ V CM ≤ 2.5V, Note 2 Power Supply Rejection Ratio PSRR 60 85 — dB VV+ = |VV–| = 1.1V to 2.5V, VOUT = VCM = 0 Common-Mode Input Capacitance C IN — 3 — pF — Output Swing VO — 0.15 1 mV Output high, RL = 100 kΩ, specified as VV+ – VOUT — — 1 Output high, RL = 100 kΩ, specified as VV+ – VOUT, –40°C ≤ TJ ≤ +85°C — 0.15 1 Output low, RL = 100 kΩ — — 1 Output low, RL = 100 kΩ, –40°C ≤ TJ ≤ +85°C — 8 33 Output high, RL = 2 kΩ, specified as VV+ – VOUT — — 50 Output high, RL = 2 kΩ, specified as VV+ – VOUT, –40°C ≤ TJ ≤ +85°C — 8 33 Output low, RL = 2 kΩ — — 50 Output low, RL = 2 kΩ –40°C ≤ TJ ≤ +85°C — 26 110 Output high, RL = 600Ω, specified as VV+ – VOUT — — 165 Output high, RL = 600Ω, specified as VV+ – VOUT, –40°C ≤ TJ ≤ +85°C — 26 110 Output low, RL = 600Ω — — 165 Output low, RL = 600Ω –40°C ≤ TJ ≤ +85°C Output Short-Circuit Current ISC 20 50 — mA Sinking or sourcing, Note 3 Supply Current IS — 0.7 1.6 mA Both amplifiers Note 1: All limits guaranteed by testing or statistical analysis. 2: CMRR is determined as follows: The maximum ΔVOS over the VCM range is divided by the magnitude of the VCM range. The measurement points are: VCM = VV– – 0.3V, (VV+ – VV–)/2, and VV+ + 0.3V. 3: Continuous short circuit may exceed absolute maximum TJ under some conditions.  2020 Microchip Technology Inc. DS20006290A-page 3 MIC7122

AC ELECTRICAL CHARACTERISTICS (2.2V) VV+ = +2.2V, VV– = 0V, VCM = VOUT = VV+/2; RL = 1 MΩ; TJ = +25°C; Note 1. Parameters Sym. Min. Typ. Max. Units Conditions Slew Rate SR — 0.7 — V/μs — Gain-Bandwidth Product GBWP — 750 — kHz — Phase Margin ϕm — 80 — ° CL = 0 pF — 40 — CL = 200 pF Gain Margin GM — 10 — dB — Interamplifier Isolation — — 90 — dB Note 2 Note 1: All limits guaranteed by testing or statistical analysis. 2: Referenced to input. MIC7122 DS20006290A-page 4  2020 Microchip Technology Inc. DC ELECTRICAL CHARACTERISTICS (5V) VV+ = +5.0V, VV– = 0V, VCM = 1.5V, VOUT = VV+/2; RL = 1 MΩ; TJ = +25°C; Note 1. Parameters Sym. Min. Typ. Max. Units Conditions Input Offset Voltage VOS — 0.5 9 mV — Input Offset Voltage Average Drift TCVOS — 3.0 — μV/°C — Input Bias Current IB — 1.0 10 pA Input Offset Current IOS — 0.5 5 pA Input Resistance RIN — >1 — TΩ — Common-Mode Rejection Ratio CMRR 55 75 — dB –0.3V ≤ V CM ≤ 5.3V, Note 2 Power Supply Rejection Ratio PSRR 55 100 — dB VV+ = |VV–| = 2.5V to 7.5V, VOUT = VCM = 0 Common-Mode Input Capacitance C IN — 3 — pF — Note 1: All limits guaranteed by testing or statistical analysis. 2: CMRR is determined as follows: The maximum ΔVOS over the VCM range is divided by the magnitude of the VCM range. The measurement points are: VCM = VV– – 0.3V, (VV+ – VV–)/2, and VV+ + 0.3V. 3: Continuous short circuit may exceed absolute maximum TJ under some conditions.

 2020 Microchip Technology Inc. DS20006290A-page 5 MIC7122 Output Swing VO — 0.3 1.0 mV Output high, RL = 100 kΩ, specified as VV+ – VOUT — — 1.5 Output high, RL = 100 kΩ, specified as VV+ – VOUT, –40°C ≤ TJ ≤ +85°C — 0.3 1.0 Output low, RL = 100 kΩ — — 1.5 Output low, RL = 100 kΩ –40°C ≤ TJ ≤ +85°C — 13 50 Output high, RL = 2 kΩ, specified as VV+ – VOUT — — 75 Output high, RL = 2 kΩ, specified as VV+ – VOUT, –40°C ≤ TJ ≤ +85°C — 13 50 Output low, RL = 2 kΩ — — 75 Output low, RL = 2 kΩ –40°C ≤ TJ ≤ +85°C — 40 165 Output high, RL = 600Ω, specified as VV+ – VOUT — — 250 Output high, RL = 600Ω, specified as VV+ – VOUT, –40°C ≤ TJ ≤ +85°C — 40 165 Output low, RL = 600Ω — — 250 Output low, RL = 600Ω –40°C ≤ TJ ≤ +85°C Output Short-Circuit Current ISC 40 140 — mA Sinking or sourcing, Note 3 Supply Current IS — 0.8 1.8 mA Both amplifiers DC ELECTRICAL CHARACTERISTICS (5V) (CONTINUED) VV+ = +5.0V, VV– = 0V, VCM = 1.5V, VOUT = VV+/2; RL = 1 M Ω; TJ = +25°C; Note 1 . Parameters Sym. Min. Typ. Max. Units Conditions Note 1: All limits guaranteed by testing or statistical analysis. 2: CMRR is determined as follows: The maximum ΔVOS over the VCM range is divided by the magnitude of the VCM range. The measurement points are: VCM = VV– – 0.3V, (VV+ – VV–)/2, and VV+ + 0.3V. 3: Continuous short circuit may exceed absolute maximum TJ under some conditions.

AC ELECTRICAL CHARACTERISTICS (5V) VV+ = +5.0V, VV– = 0V, VCM = 1.5V, VOUT = VV+/2; RL = 1 MΩ; TJ = +25°C; Note 1. Parameters Sym. Min. Typ. Max. Units Conditions Total Harmonic Distortion THD — 0.05 — % f = 1 kHz, AV = –2, RL = 2 kΩ, VOUT = 4.0 VPP Slew Rate SR — 0.6 — V/μs — Gain-Bandwidth Product GBWP — 465 — kHz — Phase Margin ϕm — 85 — ° CL = 0 pF — 40 — CL = 200 pF Gain Margin GM — 10 — dB — Interamplifier Isolation — — 90 — dB Note 2 Note 1: All limits guaranteed by testing or statistical analysis. 2: Referenced to input. MIC7122 DS20006290A-page 6  2020 Microchip Technology Inc. DC ELECTRICAL CHARACTERISTICS (15V) VV+ = +15V, VV– = 0V, VCM = 1.5V, VOUT = VV+/2; RL = 1 MΩ; TJ = +25°C; Note 1. Parameters Sym. Min. Typ. Max. Units Conditions Input Offset Voltage VOS — 0.5 9 mV — Input Offset Voltage Average Drift TCVOS — 3.0 — μV/°C — Input Bias Current IB — 1.0 10 pA Input Offset Current IOS — 0.5 5 pA Input Resistance RIN — >1 — TΩ — Common-Mode Rejection Ratio CMRR 60 85 — dB –0.3V ≤ V CM ≤ 15.3V, Note 2 Power Supply Rejection Ratio PSRR 55 100 — dB VV+ = |VV–| = 2.5V to 7.5V, VOUT = VCM = 0 Large Signal Voltage Gain AV — 340 — V/mV Sourcing or sinking, RL = 2 kΩ, Note 3 — 300 — Sourcing or sinking, RL = 600Ω, Note 3 Common-Mode Input Capacitance CIN — 3 — pF — Note 1: All limits guaranteed by testing or statistical analysis. 2: CMRR is determined as follows: The maximum ΔVOS over the VCM range is divided by the magnitude of the VCM range. The measurement points are: VCM = VV– – 0.3V, (VV+ – VV–)/2, and VV+ + 0.3V. 4: Continuous short circuit may exceed absolute maximum TJ under some conditions.

 2020 Microchip Technology Inc. DS20006290A-page 7 MIC7122 Output Swing VO — 0.8 2 mV Output high, RL = 100 kΩ, specified as VV+ – VOUT — — 3 Output high, RL = 100 kΩ, specified as VV+ – VOUT, –40°C ≤ TJ ≤ +85°C — 0.8 2 Output low, RL = 100 kΩ — — 3 Output low, RL = 100 kΩ, –40°C ≤ TJ ≤ +85°C — 40 80 Output high, RL = 2 kΩ, specified as VV+ – VOUT — — 120 Output high, RL = 2 kΩ, specified as VV+ – VOUT, –40°C ≤ TJ ≤ +85°C — 40 80 Output low, RL = 2 kΩ — — 120 Output low, RL = 2 kΩ, –40°C ≤ TJ ≤ +85°C — 130 270 Output high, RL = 600Ω, specified as VV+ – VOUT — — 400 Output high, RL = 600Ω, specified as VV+ – VOUT, –40°C ≤ TJ ≤ +85°C — 130 270 Output low, RL = 600Ω — — 400 Output low, RL = 600Ω –40°C ≤ TJ ≤ +85°C Output Short-Circuit Current ISC 50 250 — mA Sinking or sourcing, Note 4 Supply Current IS — 0.9 2.0 mA Both amplifiers DC ELECTRICAL CHARACTERISTICS (15V) (CONTINUED) VV+ = +15V, VV– = 0V, VCM = 1.5V, VOUT = VV+/2; RL = 1 M Ω; TJ = +25°C; Note 1 . Parameters Sym. Min. Typ. Max. Units Conditions Note 1: All limits guaranteed by testing or statistical analysis. 2: CMRR is determined as follows: The maximum ΔVOS over the VCM range is divided by the magnitude of the VCM range. The measurement points are: VCM = VV– – 0.3V, (VV+ – VV–)/2, and VV+ + 0.3V. 4: Continuous short circuit may exceed absolute maximum TJ under some conditions.

AC ELECTRICAL CHARACTERISTICS (15V) VV+ = +15V, VV– = 0V, VCM = 1.5V, VOUT = VV+/2; RL = 1 MΩ; TJ = +25°C; Note 1. Parameters Sym. Min. Typ. Max. Units Conditions Total Harmonic Distortion THD — 0.01 — % f = 1 kHz, AV = –2, RL = 2 kΩ, VOUT = 8.5VPP Slew Rate SR — 0.5 — V/μs V+ = 15V, Note 2 Gain-Bandwidth Product GBWP — 420 — kHz — Phase Margin ϕm — 85 — ° CL = 0 pF — 40 — CL = 200 pF Gain Margin GM — 10 — dB — Input-Referred Voltage Noise en — 37 — nV/√Hz f = 1 kHz, VCM = 1V Input-Referred Current Noise in — 1.5 — fA/√Hz f = 1 kHz Interamplifier Isolation — — 90 — dB Note 3 Note 1: All limits guaranteed by testing or statistical analysis. 2: Device connected as a voltage follower with a 10V step input. The value is the positive or negative slew rate, whichever is slower. 3: Referenced to input. MIC7122 DS20006290A-page 8  2020 Microchip Technology Inc.

TEMPERATURE SPECIFICATIONS Parameters Sym. Min. Typ. Max. Units Conditions Temperature Ranges Operating Junction Temperature Range TJ –40 — +125 °C — Storage Temperature TS –65 — +150 °C — Maximum Junction Temperature Range TJ — — +150 °C — Lead Temperature — — — +260 °C Soldering, 10 sec. Maximum Power Dissipation — — — — — — Package Thermal Resistance MSOP-8 θJA — 200 — °C/W Note 1 Note 1: Thermal resistance, θJA, applies to a part soldered on a printed-circuit board.  2020 Microchip Technology Inc. DS20006290A-page 9 MIC7122

DS20006290A-page 10  2020 Microchip Technology Inc.

2.0 PIN DESCRIPTIONS

The descriptions of the pins are listed in Table 2-1. TABLE 2-1: PIN FUNCTION TABLE Pin Number Pin Name Description 1 OUTA Op Amp A Output. 2 INA– Op Amp A Inverting Input. 3 INA+ Op Amp A Non-Inverting Input.

4 V– Negative Supply: Negative supply for split supply application or ground for

single supply applications. 5 INB+ Op Amp B Non-Inverting Input. 6 INB– Op Amp B Inverting Input. 7 OUTB Op Amp B Output. 8 V+ Positive Supply.

 2020 Microchip Technology Inc. DS20006290A-page 11 MIC7122

3.0 APPLICATION INFORMATION

3.1 Input Common-Mode Voltage

The MIC7122 tolerates input overdrive by at least 300 mV beyond either rail without producing phase inversion. If the absolute maximum input voltage is exceeded, the input current should be limited to ±5 mA maximum to prevent reducing reliability. A 10 k Ω series input resistor, used as a current limiter, will protect the input structure from voltages as large as 50V above the supply or below ground. See Figure 3-1. VIN VOUT 10kΩ RIN FIGURE 3-1: Input Current-Limit Protection.

3.2 Output Voltage Swing

Sink and source output resistances of the MIC7122 are equal. Maximum output voltage swing is determined by the load and the approximate output resistance. The output resistance is: EQUATION 3-1: ROUT V DROP ILOAD VDROP is the voltage dropped within the amplifier output stage. VDROP and ILOAD can be determined from the V O (output swing) portion of the appropriate Electrical Characteristics table. I LOAD is equal to the typical output high voltage minus V+/2 and divided by R LOAD. For example, using the DC Electrical Characteristics (5V) table, the typical output high voltage drops 13 mV using a 2 k Ω load (connected to V+/2), which produces an ILOAD of: EQUATION 3-2: Because of output stage symmetry, the corresponding typical output low voltage (13 mV) also equals VDROP. Then: EQUATION 3-3: ROUT 0.013V

3.3 Power Dissipation

The MIC7122 output drive capability requires considering power dissipation. If the load impedance is low, it is possible to damage the device by exceeding the 125°C junction temperature rating. On-chip power consists of two components: supply power and output stage power . Supply power (P S) is the product of the supply voltage (VS = VV+ – VV–) and supply current (I S). Output stage power (P O) is the product of the output stage voltage drop (V DROP) and the output (load) current (IOUT). Total on-chip power dissipation is: EQUATION 3-4: PD PS PO+ = Where: P D = Total On-Chip Power PS = Supply Power Dissipation PO = Output Power Dissipation EQUATION 3-5: Where: V S = VV+ – VV– IS = Power Supply Current VDROP = VV+ – VOUT (Sourcing Current) VDROP = VOUT – VV– (Sinking Current) Equation 3-4 and Equation 3-5 address only steady state (DC) conditions. For non-DC conditions, the user must estimate power dissipation based on the RMS value of the signal. The task is one of determining the allowable on-chip power dissipation for operation at a given ambient temperature and power supply voltage. From this determination, one may calculate the maximum allowable power dissipation and, after subtracting P determine the maximum allowable load current, which

DS20006290A-page 12  2020 Microchip Technology Inc. in turn can be used to determine the minimum load impedance that may safely be driven. The calculation is summarized below in Equation 3-6. EQUATION 3-6: PDM A X T JM A X T A– JA θJA(MSOP-8) = 200°C/W

3.4 Driving Capacitive Loads

Driving a capacitive load introduces phase lag into the output signal and this, in turn, reduces op-amp system phase margin. The application that is least forgiving of reduced phase margin is a unity gain amplifier . The MIC7122 can typically drive a 200 pF capacitive load connected directly to the output when configured as a unity-gain amplifier and powered with a 2.2V supply. At 15V operation the circuit typically drives 500 pF.

3.5 Using Large-Value Feedback

A large-value feedback resistor (>500 k Ω) can reduce the phase margin of a system. This occurs when the feedback resistor acts in conjunction with input capacitance to create phase lag in the feedback signal. Input capacitance is usually a combination of input circuit components and other parasitic capacitance, such as amplifier input capacitance and stray printed circuit board capacitance. Figure 3-2 illustrates a method of compensating phase lag caused by using a large-value feedback resistor. Feedback capacitor C FB introduces sufficient phase lead to overcome the phase lag caused by feedback resistor R FB and input capacitance C IN. The value of CFB is determined by first estimating C IN and then applying the following formula: EQUATION 3-7: RIN CIN RFB CFB   VIN CFB RFB VOUT CIN RIN FIGURE 3-2: Canceling Feedback Phase Lag. Because a significant percentage of C IN may be caused by board layout, it is important to note that the correct value of C FB may change when changing from a breadboard to the final circuit layout.

3.6 Typical Circuits

Some single-supply, rail-to-rail applications for which the MIC7122 is well suited are shown in the circuit diagrams of Figure 3-3 through Figure 3-8. 910kR1 100k VOUT 0V to V+ VIN 1»2 MIC7122 0V to V+ AV FIGURE 3-3: Non-Inverting Amplifier.

0 VOUT (V)

VIN (V) A1 R2 R1V =+ ≈ 10 FIGURE 3-4: Non-Inverting Amplifier Behavior.

DS20006290A-page 14  2020 Microchip Technology Inc.

4.0 PACKAGE MARKING INFORMATION

4.1 Package Marking Information

Example8-Lead MSOP* (FRONT) XXXX XXX 7122 YMM Example8-Lead MSOP* (BACK) WNNN 2505 Legend: XX...X Product code or customer-specific information Y Year code (last digit of calendar year) YY Year code (last 2 digits of calendar year) WW Week code (week of January 1 is week ‘01’) NNN Alphanumeric traceability code Pb-free JEDEC ® designator for Matte Tin (Sn) * This package is Pb-free. The Pb-free JEDEC designator ( ) can be found on the outer packaging for this package.

• , ▲, ▼ Pin one index is identified by a dot, delta up, or delta down (triangle mark). Note: In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. Package may or may not include the corporate logo. Underbar (_) and/or Overbar (‾) symbol may not be to scale.

 2020 Microchip Technology Inc. DS20006290A-page 15 MIC7122 8-Lead MSOP Package Outline and Recommended Land Pattern Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging

DS20006290A-page 16  2020 Microchip Technology Inc. NOTES:

 2020 Microchip Technology Inc. DS20006290A-page 17 MIC7122 APPENDIX A: REVISION HISTORY Revision A (January 2020)

• Converted Micrel data sheet MIC7122 to Micro - chip DS20006290A.
• Minor text changes throughout.

DS20006290A-page 18  2020 Microchip Technology Inc. NOTES:

 2020 Microchip Technology Inc. DS20006290A-page 19 MIC7122 PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, contact your local Microchip representative or sales office. Examples: a) MIC7122YMM: Rail-to-Rail Dual Op Amp, –40°C to +85°C Temperature Range, 8-Lead MSOP, 100/Tube b) MIC7122YMM-TR: Rail-to-Rail Dual Op Amp, –40°C to +85°C Temperature Range, 8-Lead MSOP, 2500/Reel PART NO. XX PackageDevice Device: MIC7122: Rail-to-Rail Dual Op Amp Temperature Range: Y = –40C to +85 C (Industrial) Package: MM = 8-Pin MSOP Media Type: <blank>= 100/Tube TR = 2,500/Reel X Temperature Range -XX Media Type Note 1: Tape and Reel identifier only appears in the catalog part number description. This identifier is used for ordering purposes and is not printed on the device package. Check with your Microchip Sales Office for package availability with the Tape and Reel option.

DS20006290A-page 20  2020 Microchip Technology Inc. NOTES:

 2020 Microchip Technology Inc. DS20006290A-page 21 Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE . Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights unless otherwise stated. Trademarks The Microchip name and logo, the Microchip logo, Adaptec, AnyRate, AVR, AVR logo, AVR Freaks, BesTime, BitCloud, chipKIT, chipKIT logo, CryptoMemory, CryptoRF, dsPIC, FlashFlex, flexPWR, HELDO, IGLOO, JukeBlox, KeeLoq, Kleer, LANCheck, LinkMD, maXStylus, maXTouch, MediaLB, megaAVR, Microsemi, Microsemi logo, MOST, MOST logo, MPLAB, OptoLyzer, PackeTime, PIC, picoPower, PICSTART, PIC32 logo, PolarFire, Prochip Designer, QTouch, SAM-BA, SenGenuity, SpyNIC, SST, SST Logo, SuperFlash, Symmetricom, SyncServer, Tachyon, TempTrackr, TimeSource, tinyAVR, UNI/O, Vectron, and XMEGA are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. APT, ClockWorks, The Embedded Control Solutions Company, EtherSynch, FlashTec, Hyper Speed Control, HyperLight Load, IntelliMOS, Libero, motorBench, mTouch, Powermite 3, Precision Edge, ProASIC, ProASIC Plus, ProASIC Plus logo, Quiet-Wire, SmartFusion, SyncWorld, Temux, TimeCesium, TimeHub, TimePictra, TimeProvider, Vite, WinPath, and ZL are registered trademarks of Microchip Technology Incorporated in the U.S.A. Adjacent Key Suppression, AKS, Analog-for-the-Digital Age, Any Capacitor, AnyIn, AnyOut, BlueSky, BodyCom, CodeGuard, CryptoAuthentication, CryptoAutomotive, CryptoCompanion, CryptoController, dsPICDEM, dsPICDEM.net, Dynamic Average Matching, DAM, ECAN, EtherGREEN, In-Circuit Serial Programming, ICSP, INICnet, Inter-Chip Connectivity, JitterBlocker, KleerNet, KleerNet logo, memBrain, Mindi, MiWi, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, MultiTRAK, NetDetach, Omniscient Code Generation, PICDEM, PICDEM.net, PICkit, PICtail, PowerSmart, PureSilicon, QMatrix, REAL ICE, Ripple Blocker, SAM-ICE, Serial Quad I/O, SMART-I.S., SQI, SuperSwitcher, SuperSwitcher II, Total Endurance, TSHARC, USBCheck, VariSense, ViewSpan, WiperLock, Wireless DNA, and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. The Adaptec logo, Frequency on Demand, Silicon Storage Technology, and Symmcom are registered trademarks of Microchip Technology Inc. in other countries. GestIC is a registered trademark of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in other countries. All other trademarks mentioned herein are property of their respective companies. © 2020, Microchip Technology Incorporated, All Rights Reserved. ISBN: 978-1-5224-5491-5 Note the following details of the code protection feature on Microchip devices:

• Microchip products meet the specification contained in their particular Microchip Data Sheet.
• Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used i n the intended manner and under normal conditions.
• There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
• Microchip is willing to work with the customer who is concerned about the integrity of their code.
• Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. For information regarding Microchip’s Quality Management Systems, please visit www.microchip.com/quality.

DS20006290A-page 22  2020 Microchip Technology Inc. AMERICAS Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://www.microchip.com/ support Web Address: www.microchip.com Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Austin, TX Tel: 512-257-3370 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Novi, MI Tel: 248-848-4000 Houston, TX Tel: 281-894-5983 Indianapolis Noblesville, IN Tel: 317-773-8323 Fax: 317-773-5453 Tel: 317-536-2380 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Tel: 951-273-7800 Raleigh, NC Tel: 919-844-7510 New York, NY Tel: 631-435-6000 San Jose, CA Tel: 408-735-9110 Tel: 408-436-4270 Canada - Toronto Tel: 905-695-1980 Fax: 905-695-2078 ASIA/PACIFIC Australia - Sydney Tel: 61-2-9868-6733 China - Beijing Tel: 86-10-8569-7000 China - Chengdu Tel: 86-28-8665-5511 China - Chongqing Tel: 86-23-8980-9588 China - Dongguan Tel: 86-769-8702-9880 China - Guangzhou Tel: 86-20-8755-8029 China - Hangzhou Tel: 86-571-8792-8115 China - Hong Kong SAR Tel: 852-2943-5100 China - Nanjing Tel: 86-25-8473-2460 China - Qingdao Tel: 86-532-8502-7355 China - Shanghai Tel: 86-21-3326-8000 China - Shenyang Tel: 86-24-2334-2829 China - Shenzhen Tel: 86-755-8864-2200 China - Suzhou Tel: 86-186-6233-1526 China - Wuhan Tel: 86-27-5980-5300 China - Xian Tel: 86-29-8833-7252 China - Xiamen Tel: 86-592-2388138 China - Zhuhai Tel: 86-756-3210040 ASIA/PACIFIC India - Bangalore Tel: 91-80-3090-4444 India - New Delhi Tel: 91-11-4160-8631 India - Pune Tel: 91-20-4121-0141 Japan - Osaka Tel: 81-6-6152-7160 Japan - Tokyo Tel: 81-3-6880- 3770 Korea - Daegu Tel: 82-53-744-4301 Korea - Seoul Tel: 82-2-554-7200 Malaysia - Kuala Lumpur Tel: 60-3-7651-7906 Malaysia - Penang Tel: 60-4-227-8870 Philippines - Manila Tel: 63-2-634-9065 Singapore Tel: 65-6334-8870 Taiwan - Hsin Chu Tel: 886-3-577-8366 Taiwan - Kaohsiung Tel: 886-7-213-7830 Taiwan - Taipei Tel: 886-2-2508-8600 Thailand - Bangkok Tel: 66-2-694-1351 Vietnam - Ho Chi Minh Tel: 84-28-5448-2100 EUROPE Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 Finland - Espoo Tel: 358-9-4520-820 France - Paris Germany - Garching Tel: 49-8931-9700 Germany - Haan Tel: 49-2129-3766400 Germany - Heilbronn Tel: 49-7131-72400 Germany - Karlsruhe Tel: 49-721-625370 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Germany - Rosenheim Tel: 49-8031-354-560 Israel - Ra’anana Tel: 972-9-744-7705 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Italy - Padova Tel: 39-049-7625286 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Norway - Trondheim Tel: 47-7288-4388 Poland - Warsaw Tel: 48-22-3325737 Romania - Bucharest Tel: 40-21-407-87-50 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 Sweden - Gothenberg Tel: 46-31-704-60-40 Sweden - Stockholm Tel: 46-8-5090-4654 UK - Wokingham Tel: 44-118-921-5800 Fax: 44-118-921-5820 Worldwide Sales and Service 05/14/19