MGJ2_V02 MURATA-PS | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 14
Technical content
5.2kVDC Isolated 2W Gate Drive DC-DC Converters KDC_MGJ2_S01 Page 1 of 14 www.murata.com For full details go to www.murata.com/en-global/ products/power/rohs www.murata.com SELECTION GUIDE Order Code Nominal Input Voltage Output Voltage 1 Output Voltage 2 Output Current 1 Output Current 2 Input Current at Rated Load Load Regulation (Typ) Load Regulation (Max) Ripple & Noise (Typ)2 Ripple & Noise (Max)2 Efficiency (Min) Efficiency (Typ) Isolation Capacitance MTTF1 MIL. Tel. V V V mA % mVp-p % pF kHrs MGJ2D051505SC 5 15 -5 80 40 360 5.7 7 30 50 71 76 3 2095 MGJ2D051509SC 5 15 -8.7 80 40 390 6 7 30 50 73 77.5 3 1902 MGJ2D051515SC 5 15 -15 67 67 492 7 8.5 20 35 74 78 3 2629 MGJ2D051802SC 5 18 -2.5 80 80 410 9 12 20 50 70 75 3 1376 31920 MGJ2D052005SC 5 20 -5 80 40 440 6.2 8 30 50 74 78.5 3 1655 MGJ2D121503SC 12 15 -3 95 95 170 8 10 25 50 76 80 3 2014 80644 MGJ2D121505SC 12 15 -5 80 40 150 4.7 6 30 50 75 80 3 2339 MGJ2D121509SC 12 15 -8.7 80 40 155 5.3 7.5 30 50 76 80 3 2296 MGJ2D121515SC 12 15 -15 67 67 203 6.0 8 24 40 78 82 3 2707 MGJ2D121802SC 12 18 -2.5 80 80 170 8 11 20 50 74 80 3 1553 36519 MGJ2D121805SC 12 18 -5 80 40 170 5.2 8 20 50 74 81 3 2248 49360 MGJ2D122003SC 12 20 -3.5 80 80 190 7 10 20 50 77 82 3 1371 36431 MGJ2D122005SC 12 20 -5 80 40 195 5.5 8 30 45 78 82 3 1799 MGJ2D151503SC 15 15 -3 95 95 140 8 11 25 50 75 80 3 2755 34602 MGJ2D151505SC 15 15 -5 80 40 120 5 7 30 50 75 80 3 2374 MGJ2D151509SC 15 15 -8.7 80 40 130 5 7 30 50 76 80 3 2736 MGJ2D151802SC 15 18 -2.5 80 80 130 8 11 20 50 73 79 3 1392 32908 MGJ2D152005SC 15 20 -5 80 40 145 6 8 30 50 78 81 3 1864 MGJ2D241503SC 24 15 -3 95 95 90 8 10 25 50 76 80 4 2535 70910 MGJ2D241505SC 24 15 -5 80 40 75 4.6 7 30 50 74 80.5 4 2194 MGJ2D241509SC 24 15 -8.7 80 40 80 4.8 7 30 50 77 82 4 2275 MGJ2D241802SC 24 18 -2.5 80 80 90 8 11 20 50 74 80 4 1461 32315 MGJ2D242005SC 24 20 -5 80 40 90 6 8 30 50 78 82 4 1725 MGJ2D052003SC 5 20 -3.5 80 80 470 8 11 20 50 72 77 3 1253 32603 MGJ2D151515SC 15 15 -15 67 67 167 5.5 8 23 35 75 79 3 2100 MGJ2D152003SC 15 20 -3.5 80 80 150 7 10 20 50 76 81 3 2000 80000 MGJ2D241709SC 24 17 -9 80 80 105 6 8 30 50 78 83 4 1050 47000 MGJ2D242003SC 24 20 -3.5 80 80 90 7 10 20 50 76 82 4 1333 32482 1. Calculated using MIL-HDBK-217 FN2 and Telecordia SR-332 calculation model with nominal input voltage at full load. 2. See ripple & noise test method. 3. ANSI/AAMI ES60601-1 recognition is currently pending for the MGJ2D241709SC, MGJ2Dxx1515SC, MGJ2Dxx1802SC, MGJ2D121805SC, MGJ2Dxx1503SC and MGJ2Dxx2003SC variants. All specifications typical at T A=25°C, nominal input voltage and rated output current unless otherwise specified.
FEATURES
Optimised bipolar output voltages for IGBT/ Mosfet gate drives Reinforced insulation to UL60950 recognised ANSI/AAMI ES60601-1, 1 MOPP/2 MOOP’s recognised 3 5.2kVDC isolation test voltage ‘Hi Pot Test’ Ultra low coupling capacitance SIP package style 5V, 12V, 15V & 24V inputs +18V/-5V, +20V/-3.5V & +20V/-5V outputs Operation to 100°C Characterised CMTI >200kV/ȝS Continuous barrier withstand voltage 2.4kVDC Characterised partial discharge performance PRODUCT OVERVIEW The MGJ2 series of DC-DC converters is ideal for powering ‘high side’ and ‘low side’ gate drive circuits for IGBTs and Mosfets in bridge circuits. A choice of asymmetric output voltages allows optimum drive levels for best system efficiency and EMI. The MGJ2 series is characterised for high isolation and dv/dt requirements commonly seen in bridge circuits used in motor drives and inverters, while the MGJ2 industrial grade temperature rating and construction gives long service life and reliability. INPUT CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Voltage range Continuous operation, 5V input types 4.5 5 5.5 VContinuous operation, 12V input types 10.8 12 13.2 Continuous operation, 15V input types 13.5 15 16.5 Continuous operation, 24V input types 21.6 24 26.4 NRND
5.2kVDC Isolated 2W Gate Drive DC-DC Converters KDC_MGJ2_S01 Page 2 of 14 www.murata.com www.murata.com TEMPERATURE CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Specification All output types (see safety approval section for limitations) -40 100 °CStorage -55 125 Case Temperature above ambient 5V input types 24 All other input types 20 Cooling Free air convection ABSOLUTE MAXIMUM RATINGS Short-circuit protection Continuous Lead temperature 1mm from case for 10 seconds 260°C Input voltage VIN, MGJ2D05xxxxSC 5.5V Input voltage VIN, MGJ2D12xxxxSC 13.2V Input voltage VIN, MGJ2D15xxxxSC 16.5V Input voltage VIN, MGJ2D24xxxxSC 26.4V Wave Solder Wave Solder profile not to exceed the profile recommended in IEC 61760-1 Section 6.1.3. Please refer to application notes for further information. 1. ANSI/AAMI ES60601-1 recognition is currently pending for the MGJ2D241709SC, MGJ2Dxx1515SC, MGJ2Dxx1802SC, MGJ2D121805SC, MGJ2Dxx1503SC and MGJ2Dxx2003SC variants. GENERAL CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Switching frequency All other types 45 kHzMGJ2Dxx1802SC, MGJ2D121805SC & MGJ2D241503SC types 50 ISOLATION CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Isolation test voltage Production tested for 1 second 5200 VDCQualification tested for 1 minute 5200 Resistance Viso= 500VDC 1G Ω Continuous barrier withstand voltage Non-safety barrier application 2400 VDC Safety standard UL60950-1 MGJ2Dxx1515SC types Basic/supplementary 200 Vrms All others Reinforced 150 Basic/supplementary 300 ANSI/AAMI ES60601-1 MGJ2Dxx1515SC types 1 MOOP 200 All others1 1 MOOP 300
2 MOOP/1 MOPP 200
Parameter Conditions Min. Typ. Max. Units Rated Power TA=-40ºC to 100ºC 2W Voltage Set Point Accuracy See tolerance envelopes Line regulation High V IN to low VIN 1.0 1.2 %/% INPUT CHARACTERISTICS (Continued) Parameter Conditions Min. Typ. Max. Units Input reflected ripple 051505, 051509, 051515, 052003 & 052005 types 40 mA 121503, 121505, 121509, 121515, 122003, 122005, 151503, 151505, 151509, 151515 & 152005 types 20 051802, 241505, 241509, 241709, 241802 & 242005 types 15 122003, 121802, 121805, 151802, 152003, 241503 & 242003 types 10
5.2kVDC Isolated 2W Gate Drive DC-DC Converters KDC_MGJ2_S01 Page 3 of 14 www.murata.com www.murata.com TECHNICAL NOTES ISOLATION VOLTAGE ‘Hi Pot Test’, ‘Flash Tested’, ‘Withstand Voltage’, ‘Proof Voltage’, ‘Dielectric Withstand Voltage’ & ‘Isolation Test Voltage’ are all terms that relate to the same thing, a test voltage, applied for a specified time, across a component designed to provide electrical isolation, to verify the integrity of that isolation. Murata Power Solutions MGJ2 series of DC-DC converters are all 100% production tested at 5.2kVDC for 1 second and have been qualification tested at 5.2kVDC for 1 minute. The MGJ2 series is recognised by Underwriters Laboratory, please see safety approval section for more information. When the insulation in the MGJ2 series is not used as a safety barrier, i.e. provides functional isolation only, continuous or switched voltages across the barrier up to 2.4kV are sustainable. This is established by measuring the partial discharge Inception voltage in accordance with IEC 60270. Please contact Murata for further information. REPEATED HIGH-VOLTAGE ISOLATION TESTING It is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on materials, construction and environment. We therefore strongly advise against repeated high voltage isolation testing, but if it is absolutely required, that the voltage be reduced by 20% from specified test voltage. SAFETY APPROVAL MGJ2Dxx1515SC ANSI/AAMI ES60601-1 The MGJ2Dxx1515SC variants are pending recognition by Underwriters Laboratory (UL) to ANSI/AAMI ES60601-1 and provides 1 MOOP (Means Of Operator Protection) based upon a working voltage of 200 Vrms max and 280 Vpk max., between Primary and Secondary and between Primary and its Enclosure, in a maximum ambient temperature of 85°C and/ or case temperature limit of 130°C (case temperature measured on the face opposite the pins). File Number E202895 applies. UL60950 The MGJ2Dxx1515SC variants have been recognised by Underwriters Laboratory (UL) to UL60950 for basic/supplementary insulation to a working voltage of 200Vrms in a maximum ambient temperature of 85°C and/or case temperature limit of 130°C (case temperature measured on the face opposite the pins). File number E151252 applies. Creepage and clearance 2mm Working altitude 4000m Fusing The MGJ2 Series of converters are not internally fused so to meet the requirements of UL an anti-surge input line fuse should always be used with ratings as defined below. MGJ2D051515SC: 2A MGJ2D121515SC: 750mA MGJ2D151515SC: 750mA All fuses should be UL recognised and rated to 125V. All other variants ANSI/AAMI ES60601-1 The MGJ2 series has been recognised by Underwriters Laboratory (UL) to ANSI/AAMI ES60601-1 and provides 1 MOOP (Means Of Operator Protection) based on a working voltage of 300Vrms or 2 MOOP based upon a working voltage of 200 Vrms, and 1 MOPP (Mean Of Patient Protection) based on a working voltage of 200Vrms., between Primary and Secondary. The MGJ2D241709SC, MGJ2Dxx1802SC, MGJ2D121805SC, MGJ2Dxx1503SC and MGJ2Dxx2003SC variants are currently pending recognition. File number E202895 applies. UL60950 The MGJ2 series is recognised by Underwriters Laboratory (UL) to UL60950 for reinforced insulation to a working voltage of 150Vrms and for basic/supplementary insulation to a working voltage of 300Vrms. The MGJ2D151503SC is pending recognition to UL62368. File number E151252 applies. Fusing The MGJ2 Series of converters are not internally fused so to meet the requirements of UL an anti-surge input line fuse should always be used with ratings as defined below. MGJ2D05xxxxSC: 1.25A MGJ2D12xxxxSC: 750mA MGJ2D15xxxxSC: 750mA MGJ2D24xxxxSC: 750mA All fuses should be UL recognised and rated to 125V. Over voltage category OVC I OVC II Working voltage 150Vrms 300Vrms Working altitude 2000m 2000m Creepage & clearance 2mm 2mm
5.2kVDC Isolated 2W Gate Drive DC-DC Converters KDC_MGJ2_S01 Page 4 of 14 www.murata.com www.murata.com PART NUMBER STRUCTURE MGJ 2 D XX XXXX S C Series name Power rating Output type S - Single D - Dual T - Triple Q - Quad RoHS compliant Package type S - SIP D - DIP M - Surface mount Z - ZIP Output voltage Input voltage ENVIRONMENTAL VALIDATION TESTING The following tests have been conducted on this product series, as part of our design verification process. The datasheet characteristics specify user operating conditions for this series, please contact Murata if further information about the tests is required. Test Standard Condition Temperature cycling MIL-STD-883 Method 1010, Condition B 200 cycles between two chambers set to achieve -40°C and +125°C.The dwell time shall not be less than 10min. Humidity bias JEDEC JESD22-A101 85°C ± 2°C, 85% ± 5% R.H. for >1000 hours. High temperature storage life JEDEC JESD22-A103, Condition A 125°C +10/-0°C for ≥1000 hours. Vibration MIL-STD-883 Method 2007, Condition A 1.5mm pk-pk / 20g pk min, 20-2000Hz, 4 sweeps in each of 3 mutually perpendicular axes at 3 oct/min. Shock MIL-STD-883 Method 2002, Condition A 500g 1.0ms half sine, 5 shocks in each direction of 3 mutually perpendicular axis. ESD JEDEC JESD22-A114 HBM Testing Standard at 3 stress levels; 2.0kV, 4.0kV and 8.0kV. Bump IEC Class 4M5 of ETS 300 019-2-4 Shock Spectrum Type II, 6mS duration, 250m/s 2 500 bumps in 6 directions. Solderability IPC/ECA J-STD-002, Test A and A1 SnPb (Test A) For leaded solderability the parts are conditioned in a steam ager for 8 hours ±15 min. at a temperature of 93±3°C. Dipped in solder at 245°C ±5°C for 5 +0/-0.5 seconds. Pb-free (Test A1) For lead free solderability the parts are conditioned in a steam ager for 8 hours ± 15 min. at a temperature of 93±3°C. Dipped in solder at 255°C ±5°C for 5 +0/-0.5 seconds. Solder heat JEDEC JESD22-B106 The test sample is subjected to a molten solder bath at 260 ±5°C for 10 seconds (96SC tin/ silver/copper). Solder heat (hand) MIL-STD-202 Method 210, Condition A The soldering iron is heated to 350°C ± 10°C and applied to the terminations for a duration of 4 to 5 seconds. Solvent cleaning Resistance to cleaning agents. Solvent – Novec 71IPA & Topklean EL-20A. Pulsed ultrasonic immersion 45°C- 65°C Solvent Resistance MIL-STD-883 Method 2015 Separate samples subjected to solvent A, solvent B and solvent D Lead Integrity (Adhesion) MIL-STD-883 Method 2025 Leads are bent through 90º until a fracture occurs. Lead Integrity (Fatigue) MIL-STD-883 Method 2004, condition B 2 The leads are bent to an angle of 15º. Each lead is subjected to 3 cycles. Lead Integrity (Tension/Pull) MIL-STD-883 Method 2004, Condition A 1 Pull of 0.227kg applied for 30 seconds. The force is then increased until the pins snap. RoHS COMPLIANCE INFORMATION This series is compatible with RoHS soldering systems with a peak wave solder temperature of 260ºC for 10 seconds. Please refer to application notes for further information. The pin termination finish on this product series is Tin Plate, Hot Dipped over Matte Tin with Nickel Preplate. The series is backward compatible with Sn/Pb soldering systems. For further information, please visit www.murata-ps.com/rohs
5.2kVDC Isolated 2W Gate Drive DC-DC Converters KDC_MGJ2_S01 Page 5 of 14 www.murata.com www.murata.com CHARACTERISATION TEST METHODS Ripple & Noise Characterisation Method Ripple and noise measurements are performed with the following test configuration. C1 1μF X7R multilayer ceramic capacitor, voltage rating to be a minimum of 3 times the output voltage of the DC-DC converter C2 10μF tantalum capacitor, voltage rating to be a minimum of 1.5 times the output voltage of the DC-DC converter with an ESR of less than 100mΩ at 100 kHz C3 100nF multilayer ceramic capacitor, general purpose R1 450Ω resistor, carbon film, ±1% tolerance R2 50Ω BNC termination T1 3T of the coax cable through a ferrite toroid RLOAD Resistive load to the maximum power rating of the DC-DC converter. Connections should be made via twisted wires Measured values are multiplied by 10 to obtain the specified values. Differential Mode Noise Test Schematic OSCILLOSCOPE YI N P U T SUPPLY C1 C2 C3 R1 T1 R2 Input Output DC/DC Converter RL O A D + + APPLICATION NOTES Minimum load The minimum load to meet datasheet specification is 10% of the full rated load across the specified input voltage range. Lower than 10% minimum loading will result in an increase in output voltage, which may rise to typically 1.25 times the specified output voltage if the output load falls to less than 5%. Gate Drive Applications Advisory Note For general guidance for product usage in gate drive applications please refer to “gate drive application notes”. Capacitive loading and start up Typical start up times for this series, with a typical input voltage rise time of 2.2μs and output capacitance of 10μF, are shown in the table below. The product series will start into capacitance ranging from 47μF up to 220μF with increased start times. Start-up time ms MGJ2D051505SC 3 MGJ2D051509SC 4.5 MGJ2D051515SC 21 MGJ2D051802SC 4 MGJ2D052003SC 5 MGJ2D052005SC 5 MGJ2D121503SC 3 MGJ2D121505SC 3 MGJ2D121509SC 4 MGJ2D121515SC 14.5 MGJ2D121802SC 5 MGJ2D121805SC 4 MGJ2D122003SC 5 MGJ2D122005SC 5.5 Typical Start-Up Wave Form Start-up time ms MGJ2D151503SC 3 MGJ2D151505SC 2.5 MGJ2D151509SC 3 MGJ2D151515SC 10.5 MGJ2D151802SC 3 MGJ2D152003SC 5 MGJ2D152005SC 4.5 MGJ2D241503SC 3 MGJ2D241505SC 3 MGJ2D241509SC 3 MGJ2D241709SC 4 MGJ2D241802SC 3 MGJ2D242003SC 4 MGJ2D242005SC 4
5.2kVDC Isolated 2W Gate Drive DC-DC Converters KDC_MGJ2_S01 Page 6 of 14 www.murata.com www.murata.com EFFICIENCY VS LOAD 5V INPUT 12V INPUT 15V INPUT 24V INPUT 0 1 02 03 04 05 06 07 08 09 0 1 0 0 Efficiency (%) Load (%) MGJ2D121503SC MGJ2D121505SC MGJ2D121509SC MGJ2D121515SC MGJ2D121802SC MGJ2D121805SC MGJ2D122003SC MGJ2D122005SC 0 1 02 03 04 05 06 07 08 09 0 1 0 0 Efficiency (%) Load (%) MGJ2D051505SC MGJ2D051509SC MGJ2D051515SC MGJ2D051802SC MGJ2D052003SC MGJ2D052005SC 0 1 02 03 04 05 06 07 08 09 0 1 0 0 Efficiency (%) Load (%) MGJ2D151503SC MGJ2D151505SC MGJ2D151509SC MGJ2D152003SC MGJ2D152005SC MGJ2D151515SC MGJ2D152005SC 0 1 02 03 04 05 06 07 08 09 0 1 0 0 Efficiency (%) Load (%) MGJ2D241503SC MGJ2D241505SC MGJ2D241509SC MGJ2D241709SC MGJ2D241802SC MGJ2D242003SC MGJ2D242005SC TEMPERATURE DERATING GRAPHS Full OutputCurrent Rating 95400-40 Ambient Temperature (ºC) Safe Operating Area 100400-40 Ambient Temperature (ºC) Safe Operating Area 051505, 052005, 121802, 122003, 151802, 152003, 241802 & 242003 All other variants 85400-40 Ambient Temperature (ºC) Safe Operating Area Full OutputCurrent Rating Full OutputCurrent Rating 051515, 051802, 052003, 121503, 121515 & 151515
5.2kVDC Isolated 2W Gate Drive DC-DC Converters KDC_MGJ2_S01 Page 7 of 14 www.murata.com www.murata.com POSITIVE OUTPUT VOLTAGE TOLERANCE ENVELOPES The voltage tolerance envelopes show typical load regulation characteristics for this product series. The tolerance envelope is the maximum output voltage variation due to changes in output loading and set point accuracy. 051509 & 151509 152005 241509 121505 & 241505 151515 051515 Output Load Current (%) Output Voltage Output Voltage Output Load Current (%) 100 100 100 100 100 100 Output Voltage Output Voltage Output Voltage Output Load Current (%) Output Load Current (%) 2% 1% -4% 1% 0% -5% 2% 2% -3% 0% 0% -7% 2% 1% -4% Output Load Current (%) 1% 0% -7% Output Voltage Output Load Current (%)
5.2kVDC Isolated 2W Gate Drive DC-DC Converters KDC_MGJ2_S01 Page 8 of 14 www.murata.com www.murata.com POSITIVE OUTPUT VOLTAGE TOLERANCE ENVELOPES (Continued) 241709 052003 122003, 152003 & 242003 051802 121802, 151802 & 241802 121503 241503 121805 3.5% 3% -3% Output Voltage Output Load Current (%) 1% 0% -7% Output Voltage Output Load Current (%) -7% -6% -5% Output Voltage Output Voltage Output Voltage Output Load Current (%) Output Load Current (%) Output Load Current (%) 0% 1% -6% Output Voltage Output Load Current (%) 1% 0% -5%Output Voltage Output Load Current (%) 100 100 100 100 100 100 100 1% 1% -4%Output Voltage Output Load Current (%) 10075502510
5.2kVDC Isolated 2W Gate Drive DC-DC Converters KDC_MGJ2_S01 Page 9 of 14 www.murata.com www.murata.com POSITIVE OUTPUT VOLTAGE TOLERANCE ENVELOPES (Continued) 122005 242005 051505 & 151505 052005 121509 121515 151503 4% 4% 1% 1% 1% 1% -5% -4%Output Voltage Output Load Current (%) Output Voltage Output Load Current (%) 100100 7575 5050 2525 1010 2% 1% -4%Output Voltage Output Load Current (%) 10075502510 1% 0% -7% Output Voltage Output Load Current (%) 10075502510 100 100 Output Voltage Output Voltage Output Load Current (%) Output Load Current (%) -7% -5% 3% 2% -4%Output Voltage 10075502510 Output Load Current (%)
5.2kVDC Isolated 2W Gate Drive DC-DC Converters KDC_MGJ2_S01 Page 10 of 14 www.murata.com www.murata.com NEGATIVE OUTPUT VOLTAGE TOLERANCE ENVELOPES 052005 151505 121509 & 241509 051505 241505 151515 051515 241709 3% 2% -4% 5% 4% 1% 1% -4% Output Voltage Output Voltage Output Voltage Output Voltage Output Load Current (%) Output Load Current (%) Output Load Current (%) Output Load Current (%) 6% 6% 2% 2%2% -3% -4%Output Voltage Output Voltage Output Load Current (%) Output Load Current (%) 1% 0% -7% Output Voltage Output Load Current (%) 6.5% 2% 2% -4%Output Voltage Output Load Current (%) 100 100 100 100 100 100 100 100 0% 1% -6%
5.2kVDC Isolated 2W Gate Drive DC-DC Converters KDC_MGJ2_S01 Page 11 of 14 www.murata.com www.murata.com NEGATIVE OUTPUT VOLTAGE TOLERANCE ENVELOPES (Continued) 052003 122003, 152003 & 242003 051802 121802, 151802 & 241802 121503 241503 121805 051509 9% 9% 3% 3% 3% -7% -5% 13% 5% 5% 10% 2% 3% -5% -8% -4% 13% 5% 6% -3% Output Voltage Output Voltage Output Voltage Output Voltage Output Load Current (%) Output Load Current (%) Output Load Current (%) Output Load Current (%) Output Voltage Output Voltage Output Load Current (%) Output Load Current (%) 100 100 100 100 100 100 -4%Output Voltage Output Load Current (%) 10075502510 3% 2% -3% Output Voltage Output Load Current (%) 10075502510
5.2kVDC Isolated 2W Gate Drive DC-DC Converters KDC_MGJ2_S01 Page 12 of 14 www.murata.com www.murata.com NEGATIVE OUTPUT VOLTAGE TOLERANCE ENVELOPES (Continued) 121505, 122005, 152005 & 242005 121515 151509 151503 7% 6% 2% 3%2% -4% -4% 3%2% -2% -5% -3% -10% Output Voltage Output Voltage Output Voltage Output Voltage Output Load Current (%) Output Load Current (%) Output Load Current (%) Output Load Current (%) 100100 100 100 7575 75 75 5050 50 50 2525 25 25 1010 10 10
5.2kVDC Isolated 2W Gate Drive DC-DC Converters KDC_MGJ2_S01 Page 13 of 14 www.murata.com www.murata.com PACKAGE SPECIFICATIONS MECHANICAL DIMENSIONS PIN CONNECTIONS Tube outline dimensions RECOMMENDED FOOTPRINT DETAILS Weight: 4.3g Unless otherwise stated all dimensions in mm (inches). Tube length : 525mm [20.669} ±2.0 [0.079] Tube Quantity : 25 ±0.25 (0.01) of true position. Pin Output Pin Function 1+ V IN 2- V IN 5- V OUT 6O V 7+ V OUT
5.2kVDC Isolated 2W Gate Drive DC-DC Converters KDC_MGJ2_S01 Page 14 of 14 www.murata.com Murata Power Solutions (Milton Keynes) Ltd. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. © 2025 Murata Power Solutions (Milton Keynes) Ltd. This product is subject to the following operating requirements and the Life and Safety Critical Application Sales Policy: Refer to: https://www.murata.com/en-eu/products/power/requirements www.murata.com DISCLAIMER Unless otherwise stated in the datasheet, all products are designed for standard commercial and industrial applications and NOT for safety-critical and/or life-critical applications. Particularly for safety-critical and/or life-critical applications, i.e. applications that may directly endanger or cause the loss of life, inflict bodily harm and/or loss or severe damage to equipment/property, and severely harm the environment, a prior explicit written approval from Murata is strictly required. Any use of Murata standard prod- ucts for any safety-critical, life-critical or any related applications without any prior explicit written approval from Murata shall be deemed unauthorised use. These applications include but are not limited to:
- Aircraft equipment
- Aerospace equipment
- Undersea equipment
- Power plant control equipment
- Medical equipment
- Transportation equipment ( automobiles, trains, ships, etc.)
- Traffic signal equipment
- Disaster prevention / crime prevention equipment
- Data Processing equipment Murata makes no express or implied warranty, representation, or guarantee of suitability, fitness for any particular use/purpose and/or compatibility with any applica- tion or device of the buyer, nor does Murata assume any liability whatsoever arising out of unauthorised use of any Murata product for the application of the buyer. The suitability, fitness for any particular use/purpose and/or compatibility of Murata product with any application or device of the buyer remain to be the responsibility and liability of the buyer. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards that anticipate dangerous consequences of failures, moni- tor failures and their consequences, lessen the likelihood of failures that might cause harm, and take appropriate remedial actions. Buyer will fully indemnify and hold Murata, its affiliated companies, and its representatives harmless against any damages arising out of unauthorised use of any Murata products in any safety-critical and/ or life-critical applications. Remark: Murata in this section refers to Murata Manufacturing Company and its affiliated companies worldwide including, but not limited to, Murata Power Solutions.