DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 8

Technical content

Features

  • Full Function HDMI / Display Port Solution
  • Single Connect, Flow through Routing for TMDS Lines
  • Low Capacitance (0.35 pF Typical, I/O to GND)
  • Protection for the Following IEC Standards: IEC 61000−4−2 Level 4 (±8 kV Contact)
  • UL Flammability Rating of 94 V−0
  • SZ Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q101 Qualified and PPAP Capable
  • This is a Pb−Free Device Typical Applications
  • HDMI
  • Display Port MAXIMUM RATINGS (TJ = 25°C unless otherwise noted) Rating Symbol Value Unit Operating Junction Temperature Range TJ −55 to +125 °C Storage Temperature Range Tstg −55 to +150 °C Lead Solder Temperature − Maximum (10 Seconds) TL 260 °C IEC 61000−4−2 Contact (ESD) IEC 61000−4−2 Air (ESD) ESD ESD ±15 ±15 kV kV Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. See Application Note AND8308/D for further description of survivability specs. MARKING DIAGRAM Device Package Shipping

ORDERING INFORMATION

http://onsemi.com MG2040MUTAG UDFN18 (Pb−Free) 3000 / Tape & Reel †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specification Brochure, BRD8011/D. (Note: Microdot may be in either location) 2040M/C0071 /C0071 2040 = Specific Device Code M = Date Code /C0071 = Pb−Free Package SZMG2040MUTAG UDFN18 (Pb−Free) 3000 / Tape & Reel

Figure 8. Positive TLP I−V Curve Figure 9. Negative TLP I−V Curve voltage over a range of current levels. Figure 10. Simplified Schematic of a Typical TLP

10 M/C0087

Figure 11. Comparison Between 8 kV IEC 61000−4−2 and 8 A and 16 A TLP Waveforms

Figure 14. HDMI Layout Diagram

MG2040, SZMG2040 http://onsemi.com PACKAGE DIMENSIONS UDFN18, 5.5x1.5, 0.5P/0.75P CASE 517CP ISSUE A ÉÉ NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.10 AND 0.20 MM FROM TERMINAL TIP . 4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. 5. EXPOSED ENDS OF TERMINALS ARE ELECTRICALLY ACTIVE. DIM MIN MAX MILLIMETERS A 0.45 0.55 A1 0.00 0.05 A3 0.13 REF b 0.15 0.25 D 5.50 BSC D2 0.35 0.45 E 1.50 BSC eA 0.50 BSC L 0.20 0.40 0.10 C D E BA NOTE 4 A (A3) 0.10 C PIN ONE REFERENCE 0.10 C 0.05 C C SEATING PLANE BOTTOM VIEW b eB 18X 0.10 B 0.05 AC C L SIDE VIEW TOP VIEW NOTE 3 1 11 1218 *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. SOLDERING FOOTPRINT* DETAIL C DIMENSION: MILLIMETERS RECOMMENDED DETAIL A OPTIONAL CONSTRUCTION ÉÉ ÉÉÇÇ DETAIL B MOLD CMPDEXPOSED Cu OPTIONAL CONSTRUCTION DETAIL B 0.50 1.80 0.50 0.50 PITCH eB 0.75 BSC 0.30 17X E2 0.35 0.45 eA M M E2 NOTE 5 END VIEW 0.75 PITCH 18X 0.50 DETAIL C DETAIL A 0.136X 0.136X NOTE: CENTER PADS OPTIONAL 1.50 PITCH eC eC 1.50 BSC LL2 L2 0.10 REF 0.45

0.10 REF

ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, direct ly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 MG2040/D LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: orderlit@onsemi.com ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative