Datasheet search site | www.alldatasheet.com

Document overview

  • Manufacturer or author: Julie Dargie
  • PDF pages: 3

Technical content

standexelectronics.comDatasheet Rev ADB Page 1 +1 970.879.9900 | sensorsales@standexelectronics.com MFM7-APS360-LACD4 Angular Position Sensor  Programmed 0-360 degree angular position sensor  Regulated & load dump protected input  Analog output  Plastic .7” flange mount 1.5” long housing  Deutsch DT04 4 pin with 5” 20 AWG XLPE Part Description: MFM 7 - APS 360 - LACD 4 Housing Sensor Type & Function Electrical Option Connection Type Glass Filled Nylon Flange Mount ø.7“ x 1.5“ Angular Position Sensor Output Over 360° of Rotation Linear Analog Output Deutsch DT 4 pin w/5” 20AWG XLPE ‘Angular Position Sensors’ Sensor and Target Sold Separately

DESCRIPTION

  • Sensor provides 0-5V analog output over 360 degrees of rotation.
  • Non-contact sensor detects marked magnet to define orientation.
  • Load dump protected circuit operates from 8-32VDC
  • Ratiometric output to internal 5V regulator, analog ref. output wire can be connected for regulator tolerance.
  • Operate gap range dependent on target magnet, refer to specifications chart for magnet options and gap ranges.
  • Flange mount installation ensures proper orientation and gap from target.
  • 0-5V over other angular ranges available, contact Sensor Solutions.

FEATURES

  • Non Contact
  • Resistant to Shock & Vibration
  • Linear Voltage Output
  • Output Over 360 Degrees of Rotation
  • 5V or Regulated Versions CUSTOMER FOCUSED ENGINEERING + MODULAR DESIGN HOUSING - Aluminum, stainless steel, plastic, threaded, flange mount, customer specific ELECTRICAL - Every sensor function available in various electrical options (NPN, PNP, TTL, etc.) CONNECTION - Deutsch, Amphenol, many other brands, free end wires, pigtails, any length Need a Custom Sensor Solution?... Send us your application specific requirements at sensorso.com Modify, update, or enhance any sensor with our modular features and functionality.

standexelectronics.comDatasheet Rev ADB Page 2 +1 970.879.9900 | sensorsales@standexelectronics.com Electrical Specifications Conditions Min Typ Max Unit Temperature Range* Operating -40 - +110* °C Supply Voltage, Vcc For specified accuracy +8 - +32 VDC Supply Current Into Vcc, Rl > 10k +8 +10 +16 mA Recommended Load-Gnd Allows max output swing - > 100k Inf. Ohms Analog Sat. Voltage Low Rl>100k, Vcc= 24V, - .010 .050 Volts Analog Sat. Voltage High Rl>100k, Vcc= 24V, 4.900 4.960 - Volts Power Up Time Any Angle - 12 15 mS Sampling Rate, Slow Mode Factory Standard - 600 - µS Sampling Rate, Fast Mode High Speed Option - 200 - µS Step Response Time, Slow Factory Standard - - 4.0 mS Step Response Time, Fast High Speed Option - 400 600 µS ANALOG Vout SPECS AT Vcc = 24V, See graph below. Vout@45°C, Final Test Fixture100% test, room temp .35” gap2.400 2.500 2.600 Volts Slope in Linear Range From 4 to 356 Degrees 13.8 13.89 14.0 mV/Deg Linearity Error 4-356 Deg, Accurate Gap Range -1 .2 +1 % Overall Error to +5V out 4-356 Deg, Accurate Gap Range -5 ±2 +5 Deg Overall Error to +5V out 4-356 Deg, Ext. Gap Range -7 ±4 +7 Deg Discontinuity Point Programmed at Factory - 360 - Deg * 125°C max available, HIGH TEMP upgrade, contact factory. ** Ratio metric to 5V output, contact factory. TARGET SPECIFICATIONS NOTICE The "Discontinuity Point" is the angle where the output changes from 0V to 5V. This is intentionally programmed to be as far away from the actual Linear Range as possible. With this, if the magnet goes past 0 degrees the output stays 0V; and if it goes past 360 degrees the output stays 5V. Note: Check our website or contact us to compare all our angular position sensors. Environmental Specifications Corrosion Resistance 500 hours salt spray ASTM B-117 Installation Torque 15 Foot-Pounds Maximum Enclosure Nema 1,3,4,6,13 & IEC IP67 Vibration 10 G’s 10 to 2000 Hz Sinusodal Mechanical Shock 50 G’s, 11 mS Half-Sine MFM7-APS360-LACD4 Angular Position Sensor Rev A Absolute Max Limits Min Max Unit Supply Voltage, Vcc -35 +35 Volts DC Voltage Applied to Output -0.3 5 Volts Current Into/Out of Output -30 +30 mA Magnetic Flux Density -7000 +7000 Gauss Load Dump Surge, 100 mS Rs = 25 ISO 7637 - 200 Volts Magntic Characteristics Min Typ Max Outputs will respond outside of the denied ranges, but with reduced accuracy Air Gap Range: Raw NEO Magnet Part # 300-01-071 .050” .225” .375” Air Gap Range: Raw SmCo Magnet Air Gap Range: Raw SmCo Magnet

standexelectronics.comDatasheet Rev ADB Page 3 +1 970.879.9900 | sensorsales@standexelectronics.com Please note: All technical specifications on this series datasheet refer to the standard product range. Modifications in the sense of technical progress are reserved. For general information only. For more specific information, please consult the product datasheet, available upon request. This series datasheet could contain technical inaccuracies or typographical errors. Changes are periodically made to the information herein. These change will be incorporated in future revisions. For deviating values, most current specifications and products please contact your nearest sales office. MFM7-APS360-LACD4 Angular Position Sensor Connections Chart Pin 1 (Red) Vcc Pin 3 (White) +5V Ref. Pin 2 (Black) Ground Pin 4 (Green) Analog Vo CD4-APS360 Marking CHARACTERISTIC MARKED ON THIS SURFACE DATE CODE, THIS SURFACE APS360-LA 06A LA, Protected Input, Analog Output EXTERNAL LOAD SENSOR REG 200 Ci n TVS Ro AMP Vcc in GND Vout (Analog ) Sensor Function MFM7-APS360 Date Code ‘YYM’ YY = YEAR, M = MONTH A JAN D APR H JUL L OCT B FEB E MAY J AUG M NOV C MAR G JUN K SEP N DEC Vout, Volts ANGLE Disconnuity Point 0 90 180 270 360 LINEAR RANGE Caution: A short from the Pin 3 (White) +5V wire to either Pin 1 (Red) Vcc or Pin 2 (Black) Ground wire will cause component failure.