Datasheet search site | www.alldatasheet.com

Document overview

  • Manufacturer or author: Julie Dargie
  • PDF pages: 3

Technical content

standexelectronics.comDatasheet Rev AAA Page 1 +1 970.879.9900 | sensorsales@standexelectronics.com MFM61O-18ADSO-L5CP13 Single Ch-Target Tracker Gear Tooth Sensor  Dynamic Speed Sensor  No Orientation Required  Load dump and EMI protection w/5k pull up  Plastic .61” flange mount housing w/o-ring  Integral 3-way Metri-Pack 150.2 male connector Part Description: MFM 61 O - 18 ADSO - L 5 CP 13 Housing Sensor Type & Function Electrical Option Connection Type Glass Filled Nylon Flange Mount ø.6“ x 2“ Long Digital Single Output Gear Tooth Sensor Surge Protected Input, NPN Output w/ 5k Pull up Resistor Integral 3-way Metri-Pack 150.2 male ‘Target Tracker’ No Orientation Required

DESCRIPTION

  • Hall Effect Technology sensor for gear/ferrous target detection
  • Detects 0-32 pitch gears, bolt heads, holes in steel plates, and other ferrous targets
  • Single channel digital square wave output can resolve speed or count. For directional speed sensors, contact us.
  • NPN output goes low with ferrous metal present.
  • Self-calibrating output reacts to both the leading and falling edge of any ferrous metal target
  • Easy install Flange mount design sets gap relative to target face

FEATURES

  • Solid State (Nothing to wear out!)
  • Temperature Stable
  • Near 0 Speed Operation
  • Dynamic, Self-Adjusting CUSTOMER FOCUSED ENGINEERING + MODULAR DESIGN HOUSING - Aluminum, stainless steel, plastic, threaded, flange mount, customer specific ELECTRICAL - Every sensor function available in various electrical options (NPN, PNP, TTL, etc.) CONNECTION - Deutsch, Amphenol, many other brands, free end wires, pigtails, any length Need a Custom Sensor Solution?... Send us your application specific requirements at sensorso.com Modify, update, or enhance any sensor with our modular features and functionality.

standexelectronics.comDatasheet Rev AAA Page 2 +1 970.879.9900 | sensorsales@standexelectronics.com Electrical Specifications Conditions Min Max Unit Temperature Range* Operating -40 +110* Deg C Supply Voltage, Vcc Over temperature +4.5 +28 Volts DC Supply Current, Output Off Into Vcc, Vcc = 24V +1.5 +5 mA Frequency Range Near zero speed 0.1 15k Hz Saturation Voltage High Vcc= 24V, Rload>100k 23.5 24 Volts Saturation Voltage Low Vcc= 24V, Rload>100k 0.0 0.4 Volts Internal Pull Up Resistor Vcc to Vout 4.9 5.1 K Ohms Output Resistance Ro 0.25 watts 290 310 Ohms Output Rise Time 10-90% Co < 100pF - 8.0 µS Output Fall Time 90-10% Co < 100pF - 2.0 µS ESD Nondestructive - 2000 Volts EMI 20k to 1 G Hz - 100 V / M * T max = 150°C is available, contact factory. TARGET SPECIFICATIONS NOTICE Target Specifications are for detecting an end-sensed, 14.5 pressure angle, steel spur gear. The presence of ferrous metals or strong magnetic fields near the sensor's internal magnet may invalidate the specifications. Engineers are available to assist in target design and applications with non-standard targets. Custom target specifications can only be guaranteed when the customer supplies a target along with any additional components that may affect sensor output, and the customer has validated function in the finished application. These sensors power up with the output transistor OFF (Vout High). This transistor turns ON (Vout Low) for the first time on the approach of a tooth. After the first tooth, they will not miss a target. Note: for NPN sensors, off is a high signal, while PNP sensors off is a low signal. Additional gear tooth sensors are available. Check our website or contact us to compare all our gear tooth and single channel speed sensor options. Environmental Specifications Corrosion Resistance 500 hours salt spray ASTM B-117 Installation Torque 15 Foot-Pounds Maximum Enclosure Nema 1,3,4,6,13 & IEC IP67 Vibration 10 G’s 10 to 2000 Hz Sinusodal Mechanical Shock 50 G’s, 11 mS Half-Sine MFM61O-18ADSO-L5CP13 Single Ch-Target Tracker Gear Tooth Sensor Target Performance Gear Pitch ~ (#Teeth / Dia. in Inches) Air Gap Range Typ. Max Gap 4 (.785”) Tooth to Tooth .000 to .120” .150” 8 (.393”) Tooth to Tooth .000 to .085” .110” 12 (.262”) Tooth to Tooth 100% tested before shipping .000 to .055” .075” 16 (.196”) Tooth to Tooth .000 to .035” .050” 20 (.157”) Tooth to Tooth .000 to .030” .040” 24 (.131”) Tooth to Tooth .000 to .020” .030” 32 (.098”) Tooth to Tooth .000 to .012” .020” Typical Output Duty Cycle 40 to 60% Alignment Skew Angle 360 Degrees Rev A Absolute Max Limits Min Max Unit Supply Voltage, Vcc -32 +32 Volts DC Voltage Shorted to Output

1 Minute Max -20 +32 Volts

Current into Output, T=25°C - 40 mA Load Capacitance - 0.01 µF Current Out of Output - Vcc/5k mA Load Dump, 100 mS Rs = 5 per ISO 7637-2 24V Truck Spec - 200 Volts D I M = I N CH, ID = .335”

standexelectronics.comDatasheet Rev AAA Page 3 +1 970.879.9900 | sensorsales@standexelectronics.com L5, NPN with 5k Pull Up, Protection & EMI Filter Marking Handling Instructions Please note: All technical specifications on this series datasheet refer to the standard product range. Modifications in the sense of technical progress are reserved. For general information only. For more specific information, please consult the product datasheet, available upon request. This series datasheet could contain technical inaccuracies or typographical errors. Changes are periodically made to the information herein. These change will be incorporated in future revisions. For deviating values, most current specifications and products please contact your nearest sales office. MFM61O-18ADSO-L5CP13 Single Ch-Target Tracker Gear Tooth Sensor CHARACTERISTIC- OPTION MARKED ON THIS SURFACE DATE CODE, THIS SURFACE 18ADSO-L5 06A DO NOT CONTACT FACE TO FACE CONTACT WITH OTHER MAGNETS MAY REDUCE THE MAXIMUM OPERATING GAP Date Code ‘YYM’ YY = YEAR, M = MONTH A JAN D APR H JUL L OCT B FEB E MAY J AUG M NOV C MAR G JUN K SEP N DEC Connections Chart Pin A Vcc Pin C Ground Pin B Vout CP13-18ADSO MFM61O-18ADSO SENSOR Ro 200 NPN 470pF 4700pF Vcc GND Vout