MCPTCF-V

MCPTF-V MULTICOMP | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 4

Technical content

Features

• For high density mounting
• Side actuation
• Reflow solderable Electrical Specifications Contact Arrangement : SPST Contact Rating : 50mA, 12V DC Contact Resistance : 100mΩ Max. Insulation Resistance : 100MΩ Min. 500V DC Dielectric Strength : 250V AC/1 minute Operating Force : 220 +80gf/-70gf Travel : 0.30mm (Side Push) Operating Life : 100,000 cycles Operating Temperature : -25°C to +70°C Storage Temperature : -30°C to +80°C No. Description Test Conditions Requirements Appearance 1 Visual Examination By visual examination check without any out pressure & testing There shall be no defects that affect the serviceability of the product. Electric Performance

2 Contact

Applying a static load 1.5-2 times the operating force to the centre of the stem, measurements shall be made with a 1kHz small current contact resistance meter 100mΩ Max

3 Insulation

Measurements shall be made following application of 500V DC potential across terminals and cover for 1 minute ± 5 seconds 100MΩ min Dielectric Withstanding Voltage 250V AC(50Hz or 60Hz) shall be applied across terminals and cover for 1 minute There shall be no breakdown or flashover 5 Capacitance 1MHz ±10kHz 5pF max.

6 Bounce

3 to 4 operations at a rate of 1 cycles per second 5 m seconds max Mechanical Performance 7 Operating Force Applied in the direction of operation Side push Vertical push

Page <2> V1.104/07/23 Tactile Switch – MCPT Series Side Push Newark.com/multicomp-pro Farnell.com/multicomp-pro sg.element14.com/b/multicomp-pro No. Description Test Conditions Requirements Mechanical Performance

8 Stroke

Placing the switch such that the direction of switch operation is vertical and then gradually increasing the load applied to the stem, the stroke distance for the stem to come to a stop shall be measured

9 Stop

Placing the switch such that the direction of switch operation is vertical,a static load of 2kgf shall be applied in the direction of stem opera- tion for a period of 15 seconds As shown in item 4~7 Contact Resistance: 200mΩ Max Insulation Resistance: 10MΩ min

10 Solder Heat

Soldering Temperature:260±5°C Duration of Solder Immersion: 5±1 seconds Frequency of Soldering Process 2 times max. (PCB is 1.6mm in thickness) Test time:2 hours each direction Shall be free from pronounced backlash and falling-off or break- age terminals As shown in item 4~5 Contact Resistance: 200mΩ Max Insulation Resistance: 10MΩ min

11 Vibration

Shall be vibrated in accordance with Method 201A of MIL-STD-202F Swing distance=1.5mm Frequency: 10-55-10Hz in 1-min/cycle. Direction: 3 vertical directions including the directions of operation Test time: 2 hours each direction As shown in item 4~7 Contact Resistance: 200mΩ Max Insulation Resistance: 10MΩ min

12 Shock

Shall be shocked in accordance with Method 213B condition A of MIL-STD-202F Acceleration; 50G Action time:11±1m seconds Testing Direction: 6 sides Test Cycle: 3 times in each direction Ditto Durability 13 Operating Life Measurements shall be made following the test forth below: 5mA, 5 VDC resistive load Applying a static load the operating force to the centre of the stem in the direction of operation Static Load = OF Max. Cycle of Operation: 100,000 cycles min. As shown in item 4~5 Operating force:±50% of initial force Contact Resistance: 10Ω Max Insulation Resistance: 10MΩ min Bounce: 10 m seconds Max Weather- Proof 14 Resistance Low Temperature Following the test set forth below the sample shall be left in normal temperature and humidity conditions for 1 hour before the measurements are made: Temperature:-25±3°C Time: 96 hours As shown in item 4~7 Contact Resistance: 200mΩ Max Insulation Resistance: 10MΩ min

Page <3> V1.104/07/23 Tactile Switch – MCPT Series Side Push Newark.com/multicomp-pro Farnell.com/multicomp-pro sg.element14.com/b/multicomp-pro No. Description Test Conditions Requirements Weather- Proof

15 Heat

Following the test set forth below the sample shall be left in normal temperature and humidity conditions for 1 hour before the measurements are made: Temperature:80±2°C Time: 96 hours Ditto

16 Humidity

Following the test set forth below the sample shall be left in normal temperature and humidity conditions for 1 hour before the measurements are made: Temperature:40±2°C Relative Humidity: 90~95% Time: 96 hours Ditto Soldering Conditions Condition for Soldering MCPT-V Series The condition mentioned above is the temperature on the Cu foil of the PCB surface. There are cases where board’s temperature greatly differs from switch’s surface be used not to allow switch’s surface temperature to exceed 260°C. Manual Soldering Soldering Temperature Max. 350°C Continuous Soldering Time Max. 5 seconds

Page <4> V1.104/07/23 Tactile Switch – MCPT Series Side Push Newark.com/multicomp-pro Farnell.com/multicomp-pro sg.element14.com/b/multicomp-pro Important Notice : This data sheet and its contents (the “Information”) belong to the members of the AVNET group of companies (the “Group”) or are licensed to it. No licence is granted for the use of it other than for information purposes in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any error in or omission from it or for any use made of it. Users of this data sheet should check for themselves the Information and the suitability of the products for their purpose and not make any assumptions based on information included or omitted. Liability for loss or damage resulting from any reliance on the Information or use of it (including liability resulting from negligence or where the Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group’s liability for death or personal injury resulting from its negligence. Multicomp Pro is the registered trademark of Premier Farnell Limited 2019. Part Number Table Description Part Number Tactile Switch, Non-Illuminated, w/Post, SPST, Side Push, 50mA, 12V DC, Flat SMD MCPTCF-V Tactile Switch, Non-Illuminated, SPST, Side Push, 50mA, 12V DC, Flat SMD MCPTF-V Diagram No. Part Name Material Treatment Qty

1 Cover

Stainless Steel: For PT Side Push Type And PT Front Push/Without Ground Terminal Type. Nickel Silver: For PT Front Push/With Ground Terminal Type. None

2 Stem

Vertical Push: LCP UL94V – 0 Side Push: Nylon UL94V – 0

3 Contact Stainless Steel

4 Base

Nylon UL94V – 0 Molded Black

5 Terminal Brass With Silver

6 Adhesive

Dimensions : Millimetres (Inches)