DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 22
Technical content
2011-2014 Microchip Technology Inc. DS20005049D-page 1 MCP73830/L Features:
- Complete Linear Charge Management Controller: - Integrated Pass Transistor - Integrated Current Sense - Integrated Reverse Discharge Protection
- Constant Current/Constant Voltage Operation
- High Accuracy Preset Voltage Regulation: – 4.20V + 0.75%
- Programmable Charge Current: – MCP73830L: 20 mA – 200 mA – MCP73830: 100 mA – 1000 mA
- Soft-Start to avoid In-Rush Current
- Preconditioning: – 10% and no preconditioning
- Fixed Elapsed Timer: 4 Hours
- Fixed Preconditioning Timer: 1 Hour
- Automatic Recharge: No Auto-Recharge is also available with Selected Options
- Automatic End-of-Charge Control Termination: – 7.5% and 10%
- Automatic Power-Down when Input Power Removed
- Undervoltage Lockout (UVLO)
- Chip/Charge Enable Pin (CE
- Packaging: – TDFN-6 (2x2 mm)
- Temperature Range: -40°C to +85°C Applications:
- Bluetooth Headsets
- Portable Media Players
- Rechargeable 3D Glasses
- Toy and Gaming Controllers Description: The MCP73830/L are highly integrated, Li-Ion battery charge management controllers for use in space- limited applications. The MCP73830/L devices provide specific charge algorithms for single-cell Li-Ion/Li- Polymer batteries to achieve optimal capacity and safety in the shortest charging time possible. Along with its small physical size, the low number of external components makes the MCP73830/L ideally suitable for portable applications. The MCP73830L employs a constant current/constant voltage charge algorithm. The minimum 20 mA regulated constant, fast-charge current enables the design in small Li-Ion batteries and low-supply current applications. The fast-charge, constant current value is set with one external resistor from 20 mA to 200 mA. The MCP73830/L allows up to 1000 mA charge current for applications that require faster constant current. The MCP73830/L provides a thermal foldback function that limits the charge current based on die temperature during high-power or high-ambient conditions. This thermal regulation optimizes the charge cycle time while maintaining device reliability. The MCP73830/L is fully specified over the ambient temperature range of -40°C to +85°C. The MCP73830/L is available in a 6 lead, TDFN package. Package Types (Top View) MCP73830/L 2x2 TDFN * * Includes Exposed Thermal Pad (EP); see Table 3-1. VBAT STAT CE VDD PROGVSS EP TABLE 1: AVAILABLE FACTORY PRESET OPTIONS Charge Voltage Preconditioning Charge Current End-of-Charge Control Auto-Recharge 4.2V 10%/Disabled 7.5%/ 10% Yes/No Single-Cell Li-Ion/Li-Polymer Battery Charge Management Controllers in 2x2 TDFN
DS20005049D-page 2 2011-2014 Microchip Technology Inc. Typical Application Functional Block Diagram STAT VDD VBAT PROG 2 6 Regulated wall cube 4.7 µF 2k 1-Cell Li-Ion Battery VSS5 4.7 µF 1k CEHiLo MCP73830/L STAT PROG VBAT VSS Direction Control TERM UVLO, Reference, Charge Control, Timer and Status Logic G=0.001 VDD CA VREF PRECONDITION+ - VREF VA VREF VREF CE CHRG - VREF UVLO - VREF VDD
2011-2014 Microchip Technology Inc. DS20005049D-page 3 MCP73830/L
1.0 ELECTRICAL
Absolute Maximum Ratings† ESD protection on all pins Human Body Model (1.5 kW in Series with 100 pF) 2k V † Notice: Stresses above those listed under “Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. DC CHARACTERISTICS Electrical Specifications: Unless otherwise indicated, all limits apply for VDD= [VREG(Typical) + 0.3V] to 6V, TA = -40°C to +85°C. Typical values are at +25°C, VDD = [VREG (Typical) + 1.0V] Parameters Sym. Min. Typ. Max. Units Conditions Supply Input Input Voltage Range V DD 3.75 — 6 V Supply Current I SS — 0.6 2 µA Shutdown; VDD VSTOP - 300 mV — 500 900 µA Charging — 25 50 µA Standby; CE = V DD Battery Discharge Current Output Reverse Leakage Current IDISCHARGE 10 15 µA Charge Complete; VDD is Present — 0.5 — µA Shutdown (VDD VBAT, or VDD < VSTOP) — 0.5 — µA Standby; CE = V DD Undervoltage Lockout UVLO Start Threshold V START 3.45 3.6 3.75 V V DD Low-to-High UVLO Stop Threshold V STOP 3.15 3.3 3.45 V V DD High-to-Low UVLO Hysteresis V HYS — 300 — mV Voltage Regulation (Constant Voltage Mode) Regulated Output Voltage Options VREG —4 . 2 0— V V DD = [VREG(Typical)+1V] IOUT = 30 mA Output Voltage Tolerance VRTOL -0.75 — 0.75 % T A= -5°C to +55°C Line Regulation VBAT/VBAT)/ VDD| — 0.2 0.3 %/V V DD = [VREG(Typical)+1V] to 12V IOUT = 30 mA Load Regulation VBAT/VBAT|— 0 . 2 0 . 3 % I OUT = 30 mA - 150 mA VDD = [VREG(Typical)+1V] Supply Ripple Attenuation PSRR 52 — dB I OUT = 30 mA, 10 Hz to 1 kHz 47 — dB I OUT = 30 mA, 10 Hz to 10 kHz Note 1: Not production tested. Ensured by design.
DS20005049D-page 4 2011-2014 Microchip Technology Inc. Current Regulation (Fast Charge, Constant-Current Mode) Fast Charge Current Regulation MCP73830L IREG 20 — 200 mA — 20 — mA PROG = 10 k — 200 — mA PROG = 1 k Fast Charge Current Regulation MCP73830 IREG 100 — 1000 mA — 100 — mA PROG = 10 k — 1000 — mA PROG = 1 k Charge Current Tolerance IRTOL —1 0— % V DD = 4.5V, TA = -5°C to +55°C Preconditioning Current Regulation (Trickle Charge Constant Current Mode) Precondition Current Ratio IPREG/IREG — 10 — % PROG = 1 k to 10 k — 100 — % No Preconditioning Precondition Voltage Threshold Ratio VPTH/VREG 70 72 75 % V BAT Low-to-High TA = -5°C to +55°C Precondition Hysteresis VPHYS — 100 — mV Charge Termination Charge Termination Current Ratio ITERM/IREG 5.6 7.5 9.4 % PROG = 1 k to 10 k 81 0 1 2 % V DD = 4.5V, TA=-5°C to +55°C Automatic Recharge Recharge Voltage Threshold Ratio VRTH/VREG 94.5 96.5 98.5 % V BAT High-to-Low —0— % No Automatic Recharge Pass Transistor ON-Resistance ON-Resistance R DSON — 500 — m VDD = 4.5V, TJ = 105°C (Note 1) Status Indicator – STAT Sink Current I SINK —1 63 0 m A Low Output Voltage V OL —0 . 4 1 V I SINK = 4 mA Input Leakage Current I LK — 0.01 1 µA High Impedance, V DD on Pin PROG Input Charge Impedance Range RPROG 1— 1 0 k Automatic Power Down Automatic Power Down Entry Threshold VPDENTRY —V BAT +5 0m V — V V DD Falling Automatic Power Down Exit Threshold VPDEXIT —V BAT + 150 mV — V V DD Rising Charge Enable (CE) Input High Voltage Level TSD 1.5 — — V Input Low Voltage Level VIL —— 0 . 8 V Input Leakage Current I LK —5 8 µ A V DD = 5V TA= -5°C to +55°C DC CHARACTERISTICS (CONTINUED) Electrical Specifications: Unless otherwise indicated, all limits apply for VDD= [VREG(Typical) + 0.3V] to 6V, TA = -40°C to +85°C. Typical values are at +25°C, VDD = [VREG (Typical) + 1.0V] Parameters Sym. Min. Typ. Max. Units Conditions Note 1: Not production tested. Ensured by design.
2011-2014 Microchip Technology Inc. DS20005049D-page 5 MCP73830/L Thermal Shutdown Die Temperature T SD — 150 — C Die Temperature Hysteresis TSDHYS —1 0— C AC CHARACTERISTICS Electrical Specifications: Unless otherwise specified, all limits apply for VDD= [VREG(Typical)+0.3V] to 6V, TA = -40°C to +85°C. Typical values are at +25°C, VDD= [VREG(Typical)+1.0V] Parameters Sym. Min. Typ. Max. Units Conditions Elapsed Timer Elapsed Timer Period t ELAPSED 3.5 4.0 4.5 Hours Preconditioning Timer Preconditioning Timer Period t PRECHG 0.8 1 1.2 Hours Status Indicator Status Output Turn-Off t OFF —— 5 0 0µ s I SINK = 1 mA to 0 mA (Note 1) Status Output Turn-On t ON —— 5 0 0µ s I SINK = 0 mA to 1 mA (Note 1) Note 1: Not production tested. Ensured by design. TEMPERATURE SPECIFICATIONS Electrical Specifications: Unless otherwise indicated, all limits apply for VDD = [VREG (Typical) + 0.3V] to 6V. Typical values are at +25°C, VDD = [VREG (Typical) + 1.0V] Parameters Sym. Min. Typ. Max. Units Conditions Temperature Ranges Specified Temperature Range T A -40 — +85 °C Operating Temperature Range T J -40 — +125 °C Storage Temperature Range T A -65 — +150 °C Thermal Package Resistances Thermal Resistance, TDFN-6 (2x2) JA — 91 — °C/W 4-Layer JC51-7 Standard Board, Natural Convection JC —1 9— ° C / W DC CHARACTERISTICS (CONTINUED) Electrical Specifications: Unless otherwise indicated, all limits apply for VDD= [VREG(Typical) + 0.3V] to 6V, TA = -40°C to +85°C. Typical values are at +25°C, VDD = [VREG (Typical) + 1.0V] Parameters Sym. Min. Typ. Max. Units Conditions Note 1: Not production tested. Ensured by design.
DS20005049D-page 6 2011-2014 Microchip Technology Inc.
2.0 TYPICAL PERFORMANCE CURVES
Note: Unless otherwise indicated, VDD = [VREG(Typical) + 1V], IOUT = 30 mA and TA= +25°C, Constant Voltage mode. FIGURE 2-1: Battery Regulation Voltage (VBAT) vs. Supply Voltage (VDD). FIGURE 2-2: Battery Regulation Voltage (VBAT) vs. Ambient Temperature (TA). FIGURE 2-3: Battery Regulation Voltage (VBAT) vs. Ambient Temperature (TA). FIGURE 2-4: Battery Regulation Voltage (VBAT) vs. Charge Current (IOUT). FIGURE 2-5: Charge Current (IOUT) vs. Programming Resistor (RPROG), MCP73830L. FIGURE 2-6: Output Leakage Current (IDISCHARGE) vs. Ambient Temperature (TA). Note: The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore outside the warranted range. 4.10 4.15 4.20 4.25 4.30 VREG (V) IOUT = 100 mA 4.00 4.05 - 4 5 - 3 5 - 2 5 - 1 5- 5 5 1 52 53 54 55 56 57 58 5 Temp (°C) OUT VDD = 5.2V 4.10 4.15 4.20 4.25 4.30VREG (V) I =3 0m A 4.00 4.05 - 4 5 - 3 5 - 2 5 - 1 5- 5 5 1 52 53 54 55 56 57 58 5 Temp (°C) IOUT =3 0m A VDD = 5.2V 3.6 3.8 4.0 4.2 4.4 4.6 4.8 5.0 IDIS (µA) VDD = VREG VBAT = 3.2V 3.0 3.2 3.4 - 4 0 - 3 0 - 2 0 - 1 00 1 02 03 04 05 06 07 08 0 Temp (°C)
DS20005049D-page 8 2011-2014 Microchip Technology Inc.
3.0 PIN DESCRIPTION
The descriptions of the pins are listed in Table 3-1. TABLE 3-1: PIN FUNCTION TABLES
3.1 Battery Management 0V Reference
(VSS) Connect to the negative terminal of the battery and input supply.
3.2 Status Output (STAT)
STAT is an open-drain logic output for connection to an LED for charge status indication in stand-alone applications. Alternatively, a pull-up resistor can be applied for interfacing to a host microcontroller. Refer to Table 5-1 for a summary of the status output during a charge cycle.
3.3 Battery Charge Control Output
(VBAT) Connect to the positive terminal of the battery. Bypass to VSS with a minimum of 1 µF to ensure loop stability when the battery is disconnected.
3.4 Battery Management Input Supply
(VDD) A supply voltage of [V REG (Typical) + 0.3V] to 6.0V is recommended. Bypass to VSS with a minimum of 1 µF.
3.5 Charge Enable (CE )
The MCP73830/L is always enabled with an internal pull-down resistor. Pulling the CE pin high will enter Standby mode.
3.6 Current Regulation Set (PROG)
The fast charge current is set by placing a resistor from PROG to VSS during Constant Current (CC) mode. Refer to Section 5.4 “Constant Current Mode – Fast Charge” for details.
3.7 Exposed Pad (EP)
The Exposed Thermal Pad (EP) should be connected to the exposed copper area on the Printed Circuit Board (PCB) for thermal enhancement purposes. Additional vias on the copper area under the MCP73830/L device can improve the performance of heat dissipation and simplify the assembly process. MCP73830/L Symbol I/O Function TDFN SS — Battery management 0V reference. 2 STAT O Battery charge status output. 3V BAT I/O Charge control output. Regulates the charge current and battery voltage. The pin is disconnected during Shutdown mode. 4V DD I Input power supply. 5C E I Charge Enable pin. Pull the pin high to disable the device. It is internally pulled down. Leave the pin float if not used. 6 PROG I/O Battery charge current regulation program. 7 EP — Exposed pad.
2011-2014 Microchip Technology Inc. DS20005049D-page 9 MCP73830/L
4.0 DEVICE OVERVIEW
The MCP73830/L are simple, but fully integrated, linear charge management controllers. Figure 4-1 depicts the operational flow algorithm. FIGURE 4-1: The MCP73830/L Flowchart. VBAT > VPTH *Continuously monitoredSHUTDOWN MODE VDD < (UVLO) VDD < (VBAT)* VBAT > 96.5% VREG STAT = High Z STANDBY MODE* CE = High STAT = High Z PRECONDITIONING MODE Charge Current = IREG STAT = Low PRE-TIMER FAULT NO Charge Current STAT = Flash (2 Hz) Preconditioning Timer Suspended TIMER FAULT NO Charge Current STAT = High Z Timer Suspended CONSTANT CURRENT MODE Charge Current = IPREG STAT = Low Preconditioning Timer Suspended Elapsed Timer Enabled CONSTANT VOLTAGE MODE Charge Voltage = VREG STAT = Low CHARGE COMPLETE MODE NO Charge Current STAT = High Z Timer Reset VBAT = VREG VBAT >= VPTH VBAT < VPTH IBAT < ITERM VBAT < VRTH Recharge Mode (available when selected device has automatic recharge option). CE = Low CE = Low No Auto-Recharge option
DS20005049D-page 10 2011-2014 Microchip Technology Inc.
5.0 DETAILED DESCRIPTION
5.1 Undervoltage Lockout (UVLO)
An Internal Undervoltage Lockout (UVLO) circuit monitors the input voltage and keeps the charger in Shutdown mode until the input supply rises above the UVLO threshold. In the event a battery is present when the input power is applied, the input supply must rise approximately 150 mV above the battery voltage before the MCP73830/L devices become operational. The UVLO circuit places the device in Shutdown mode if the input supply falls to approximately 150 mV above the battery voltage. The UVLO circuit is always active. Any time the input supply is below the UVLO threshold, or approximately 150 mV of the voltage at the V BAT pin, the MCP73830/L devices are placed in Shutdown mode.
5.2 Charge Qualification
When the input power is applied, the input supply must rise 150 mV above the battery voltage before the MCP73830/L becomes operational. The automatic power-down circuit places the device in Shutdown mode if the input supply falls to within +50 mV of the battery voltage. The automatic circuit is always active. Any time the input supply is within +50 mV of the voltage at the V BAT pin, the MCP73830/L is placed in Shutdown mode. For a charge cycle to begin, the automatic power- down conditions must be met, and the charge enable input must be above the input high threshold. The battery voltage should be less than 96.5% of V REG.
5.2.1 BATTERY MANAGEMENT INPUT
SUPPLY (VDD) The VDD input is the input supply to the MCP73830/L. The MCP73830/L automatically enters Power-Down mode if the voltage on the V DD input falls to within +50 mV of the battery voltage. This feature prevents draining the battery pack when the V DD supply is not present.
5.2.2 BATTERY CHARGE CONTROL
OUTPUT (VBAT) The battery charge control output is the drain terminal of an internal P-channel MOSFET. The MCP73830/L provides constant current and voltage regulation to the battery pack by controlling this MOSFET in the linear region. The battery charge control output should be connected to the positive terminal of the battery pack.
5.2.3 BATTERY DETECTION
The MCP73830/L device detects the battery presence by monitoring the voltage at VBAT. The charge flow will initiate when the voltage on V BAT is pulled below the VRECHARGE threshold. Refer to Section 1.0 “Electri- cal Characteristics” for VRECHARGE values. The value will be the same for non-rechargeable devices. When V BAT >V REG + Hysteresis, the charge will be suspended or not started, depending on the condition, to prevent the overcharge that may occur.
5.3 Preconditioning
If the voltage at the VBAT pin is less than the precondi- tioning threshold, the MCP73830/L devices enter Preconditioning mode. The preconditioning threshold is factory set. Refer to Section 1.0 “Electrical Charac- teristics” for preconditioning threshold options. In this mode, the MCP73830/L devices supply 10% of the fast charge current (established with the value of the resistor connected to the PROG pin) to the battery. When the voltage at the V BAT pin rises above the pre- conditioning threshold, the MCP73830/L device enters the Constant Current (Fast Charge) mode.
5.3.1 TIMER EXPIRED DURING
If the internal timer expires before the voltage threshold is reached for Fast Charge mode, a timer fault is indicated, and the charge cycle terminates. The MCP73830/L devices remain in this condition until the battery is removed, the input power is cycled, or CE is toggled. If the battery is removed, the MCP73830/L devices enter Standby mode, where they remain until a battery is reinserted. Note: The MCP73830/L devices also offer options with no preconditioning. Note: The typical preconditioning timers for the MCP73830/L are 60 minutes.
2011-2014 Microchip Technology Inc. DS20005049D-page 11 MCP73830/L
5.4 Constant Current Mode – Fast
During Constant Current mode, the programmed charge current is supplied to the battery or load. The charge current is established using a single resis- tor from PROG to V SS. The program resistor and the charge current are calculated using the following equation: EQUATION 5-1: MCP73830L EQUATION 5-2: MCP73830 Constant Current mode is maintained until the voltage at the V BAT pin reaches the regulation voltage, V REG. When Constant Current mode is invoked, the internal timer is reset.
5.4.1 TIMER EXPIRED DURING
CONSTANT CURRENT – FAST CHARGE MODE If the internal 4-hour timer expires before the recharge voltage threshold is reached, a timer fault is indicated and the charge cycle terminates. The MCP73830/L devices remain in this condition until the battery is reinserted, or the input power or CE is cycled.
5.5 Constant Voltage Mode
When voltage at the V BAT pin reaches the regulation voltage, VREG, the constant voltage regulation begins. The regulation voltage is factory set to 4.2V, with a tolerance of ±0.75%.
5.6 Charge Termination
The charge cycle is terminated when, during Constant Voltage mode, the average charge current diminishes below a threshold established with the value of 7.5%, 10% of fast charge current, or the internal timer has expired. A 1 ms filter time on the termination compara- tor ensures that transient load conditions do not result in premature charge cycle termination. The timer period is factory set and no timer option is available. Refer to Section 1.0 “Electrical Characteristics” for timer period value.
5.7 Automatic Recharge
MCP73830/L devices with automatic recharge options continuously monitor the voltage at the VBAT pin during the Charge Complete mode. If the voltage drops below the recharge threshold, another charge cycle begins, and current is once again supplied to the battery or load. The recharge threshold is factory set. Refer to Section 1.0 “Electrical Characteristics” for recharge threshold options. For the MCP73830/L with no recharge option, the devices will go into Standby mode when a termination condition is met. The charge will not restart until one of the following conditions is met:
- Battery is removed from the system and inserted again.
- VDD is removed and plugged in again.
- C E is cycled.
5.8 Thermal Regulation
The MCP73830/L should limit the charge currents based on the die temperature. The thermal regulation optimizes the charge cycle time while maintaining device reliability. Figure 5-1 depicts the thermal regulation for the MCP73830/L devices. Refer to Section 1.0 “Electrical Characteristics” for thermal package resistances, and Section 6.1.1.3 “Thermal Considerations” for calculating power dissipation. FIGURE 5-1: Thermal Regulation. IREG 200 RPROG Where: RPROG =k i l o - o h m s ( k) IREG = milliampere (mA) IREG 1000 RPROG Where: RPROG =k i l o - o h m s ( k) IREG = milliampere (mA) Note: The MCP73830/L also offer options with no automatic recharge. 100 150 200 250 300 03 0 6 0 9 0 1 2 0 1 5 0 Junction Temperature (C) Maximum Charge Current (mA) Mimimum Maximum
DS20005049D-page 12 2011-2014 Microchip Technology Inc.
5.9 Thermal Shutdown
The MCP73830/L suspends charging if the die tem- perature exceeds +150°C. Charging will resume when the die temperature has cooled by approximately 10°C. The thermal shutdown is a secondary safety feature in the event that there is a failure within the thermal regulation circuitry.
5.10 Status Indicator
The charge status output of the MCP73830/L is open- drain, and, as such, has two different states: Low (L), and High-Impedance (High Z). The charge status out- puts can be used to illuminate the LEDs. Optionally, the charge status output can be used as an interface to a host microcontroller. The faulty indication of a pre- conditioning timer also indicates defective batteries, when it fails to pass preconditioning threshold during the given time. Table 5-1 summarizes the state of the status outputs during a charge cycle. TABLE 5-1: STATUS OUTPUTS Charge Cycle State STAT Shutdown High Z No Battery Present High Z Preconditioning L Constant Current Fast Charge L Constant Voltage L Charge Complete High Z Timer Fault High Z Preconditioning Timer Fault Flashing (2 Hz)
2011-2014 Microchip Technology Inc. DS20005049D-page 13 MCP73830/L
6.0 APPLICATIONS
The MCP73830 is designed to operate in conjunction with a host microcontroller or in stand-alone applica- tions. The MCP73830/L provides the preferred charge algorithm for dual Lithium-Ion or Lithium-Polymer cell’s constant current, followed by constant voltage. Figure 6-1 depicts a typical stand-alone application circuit, while Figure 6-2 depicts the accompanying charge profile. FIGURE 6-1: Typical Application Circuit. FIGURE 6-2: Typical Charge Profile (Li-Ion Battery).
6.1 Application Circuit Design
Due to the low efficiency of linear charging, the most important factors are thermal design and cost, which are a direct function of the input voltage, output current and thermal impedance between the battery charger and the ambient cooling air. The worst-case situation is when the device has transitioned from Preconditioning mode to Constant Current mode. In this situation, the battery charger has to dissipate the maximum power. A trade-off must be made between the charge current, cost and thermal requirements of the charger.
6.1.1 COMPONENT SELECTION
Selection of the external components in Figure 6-1 is crucial to the integrity and reliability of the charging system. The following discussion is intended as a guide for the component selection process.
6.1.1.1 Charge Current
The preferred fast charge current for Li-Ion/Li-Poly cells is below the 1C rate, with an absolute maximum current at the 2C rate. The recommended fast charge current should be obtained from the battery manufacturer. For example, a 500 mAh battery pack with 0.7C preferred fast charge current has a charge current of 350 mA. Charging at this rate provides the shortest charge cycle times without degradation to the battery pack performance or life.
6.1.1.2 Input Over Voltage Protection
(IOVP) Input over voltage protection must be used when the input power source is hot-pluggable. This includes USB cables and wall-type power supplies. The cabling of these supplies acts as an inductor. When the supplies are connected/disconnected from the system, large voltage transients are created which may damage the system circuitry. These transients should be snubbed out. A transzorb - unidirectional or bidirectional - con- nected from the V+ input supply connector to the 0V ground reference will snub the transients. An example of this can be seen in Figure 6-3. STAT VDD VBAT PROG 2 6 Regulated wall cube 4.7µF 2k 1-Cell Li-Ion Battery VSS5 4.7 µF 1k CEHiLo MCP73830/L Note: Please consult with your battery supplier, or refer to the battery data sheet, for the preferred charge rate.
DS20005049D-page 14 2011-2014 Microchip Technology Inc. FIGURE 6-3: Input Over Voltage Protection Example.
6.1.1.3 Thermal Considerations
The worst-case power dissipation in the battery char- ger occurs when the input voltage is at the maximum and the device has transitioned from Preconditioning mode to Constant Current mode. In this case, the power dissipation is: EQUATION 6-1: Power dissipation with a 5V, ±10% input voltage source, 200 mA ±10%, and preconditioning threshold voltage at 6V is: EQUATION 6-2: This power dissipation with the battery charger in the 2x2 TDFN-6 package will result in a temperature of approximately 10.45 C (PCB mounted) above room temperature.
6.1.1.4 External Capacitors
The MCP73830 is stable with or without a battery load. In order to maintain good AC stability in Constant Volt- age mode, a minimum capacitance of 1 µF is recommended to bypass the V BAT pin to V SS. This capacitance provides compensation when there is no battery load. In addition, the battery and interconnec- tions appear inductive at high frequencies. These elements are in the control feedback loop during Constant Voltage mode. Therefore, the bypass capaci- tance may be necessary to compensate for the inductive nature of the battery pack. A minimum of 16V rated 1 µF is recommended to apply for output capacitor, and a minimum of 25V rated 1 µF is recommended to apply for input capacitor for typical applications. Virtually any good quality output filter capacitor can be used independent of the capacitor’s minimum Effective Series Resistance (ESR) value. The actual value of the capacitor (and its associated ESR) depends on the out- put load current. A 1 µF ceramic, tantalum or aluminum electrolytic capacitor at the output is usually sufficient to ensure stability.
6.1.1.5 Reverse-Blocking Protection
The MCP73830/L provides protection from a faulted or shorted input. Without the protection, a faulted or shorted input would discharge the battery pack through the body diode of the internal pass transistor. STAT VDD CE VBAT 2 mm x 2 mm DFN MCP73830 PROG 2 6 Regulated Wall Cube VSS 0.5 CINTVS SMAJ5.0A/AC PowerDissipation V DDMAX VPTHMIN– IREGMAX= Where: VDDMAX = the maximum input voltage IREGMAX = the maximum fast charge current VPTHMIN = the minimum transition threshold voltage PowerDissipation 5.5V 3.0V – 220mA 0.55W·== TABLE 6-1: MLCC CAPACITOR EXAMPLE MLCC Capacitors Temperature Range Tolerance X7R -55 C to + 125C± 1 5 % X5R -55 C to + 85C ±15%
2011-2014 Microchip Technology Inc. DS20005049D-page 15 MCP73830/L
6.2 PCB Layout Issues
For optimum voltage regulation, place the battery pack as close as possible to the device’s VBAT and VSS pins, which is recommended to minimize voltage drops along the high current carrying PCB traces. If the PCB layout is used as a heat sink, adding many vias in the heat sink pad can help conduct more heat to the backplane of the PCB, thus reducing the maximum junction temperature. Figure 6-5 and Figure 6-6 depict a typical layout with PCB heat sinking. FIGURE 6-4: Typical Layout (Top). FIGURE 6-5: Typical Layout (Top Metal). FIGURE 6-6: Typical Layout (Bottom).
DS20005049D-page 16 2011-2014 Microchip Technology Inc.
7.0 PACKAGING INFORMATION
7.1 Package Marking Information
Legend: XX...X Customer-specific information Y Year code (last digit of calendar year) YY Year code (last 2 digits of calendar year) WW Week code (week of January 1 is week ‘01’) NNN Alphanumeric traceability code Pb-free JEDEC ® designator for Matte Tin (Sn) * This package is Pb-free. The Pb-free JEDEC designator ( ) can be found on the outer packaging for this package. Note: In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. XXX 6-Lead TDFN (2x2 mm) NNN 0AA Example 256 Part Number Code MCP73830T-2AAI/MYY 2AA MCP73830LT-0AAI/MYY 0AA MCP73830LT-0BCI/MYY 0BC
2011-2014 Microchip Technology Inc. DS20005049D-page 17 MCP73830/L Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging
DS20005049D-page 18 2011-2014 Microchip Technology Inc. Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging
2011-2014 Microchip Technology Inc. DS20005049D-page 19 MCP73830/L APPENDIX A: REVISION HISTORY Revision D (July 2014) The following is the list of modifications: 1. Added the “Available Factory Preset Options” table. 2. Removed any mention of Fixed Elapse Timer having a disabled option. 3. Removed any mention of an option with no precondition timer. 4. Corrected the flow-chart in Figure 4-1, specify- ing STAT = High Z in the Charge Complete Mode text box. 5. Updated Table 5-1. 6. Added the Section 6.1.1.2, "Input Over Volt- age Protection (IOVP)". 7. Added Figure 6-3. Revision C (August 2013) The following is the list of modifications: 1. Updated the “Temperature Specifications” table. 2. Updated Section 6.1.1.3, "Thermal Consider- ations". Revision B (December 2011) The following is the list of modifications: 1. Updated Figure 4-1. 2. Removed the MCP73830 and MCP73830L options from the “Product Identification Sys- tem” section. Revision A (September 2011)
- Original Release of this Document.
DS20005049D-page 20 2011-2014 Microchip Technology Inc. PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office . Device: MCP73830T: Single Cell Li-Ion/Li-Polymer Battery Device, Tape and Reel MCP73830LT: Single Cell Li-Ion/Li-Polymer Battery Device, Tape and Reel Standard Options: IREG (mA) VREG (V) IPRECONDITION (%) VPRECONDITION (%) ITERM (%) RTH (%) MCP73830LT 0AA 200 4.2 10 71.5 7.5 96.5 MCP73830LT 0BC 200 4.2 100 71.5 10 96.5 MCP73830T 2AA 1000 4.2 10 71.5 7.5 96.5 Temperature Range: I= - 4 0 C to +85C (Industrial) Package: MY = Plastic Thin Dual Flat, No Lead Package, 2x2x0.8 mm Body (TDFN), 6-Lead * Y = nickel palladium gold manufacturing designator. Only available on the TDFN package. PART NO. X XX PackageTemperature Range Device Examples: a) MCP73830T-2AAI/MYY: Tape and Reel, Single Cell Li-Ion/Li-Polymer Battery Device b) MCP73830LT-0AAI/MYY: Tape and Reel, Single Cell Li-Ion/Li-Polymer Battery Device c) MCP73830LT-0BCI/MYY: Tape and Reel, Single Cell Li-Ion/Li-Polymer Battery Device -XXX Standard Options
2011-2014 Microchip Technology Inc. DS20005049D-page 21 Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY , PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE . Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, dsPIC, FlashFlex, flexPWR, JukeBlox, KEELOQ, KEELOQ logo, Kleer, LANCheck, MediaLB, MOST, MOST logo, MPLAB, OptoLyzer, PIC, PICSTART, PIC 32 logo, RightTouch, SpyNIC, SST, SST Logo, SuperFlash and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. The Embedded Control Solutions Company and mTouch are registered trademarks of Microchip Technology Incorporated in the U.S.A. Analog-for-the-Digital Age, BodyCom, chipKIT, chipKIT logo, CodeGuard, dsPICDEM, dsPICDEM.net, ECAN, In-Circuit Serial Programming, ICSP, Inter-Chip Connectivity, KleerNet, KleerNet logo, MiWi, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, MultiTRAK, NetDetach, Omniscient Code Generation, PICDEM, PICDEM.net, PICkit, PICtail, RightTouch logo, REAL ICE, SQI, Serial Quad I/O, Total Endurance, TSHARC, USBCheck, VariSense, ViewSpan, WiperLock, Wireless DNA, and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. Silicon Storage Technology is a registered trademark of Microchip Technology Inc. in other countries. GestIC is a registered trademarks of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in other countries. All other trademarks mentioned herein are property of their respective companies. © 2011-2014, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. ISBN: 978-1-63276-386-0 Note the following details of the code protection feature on Microchip devices:
- Microchip products meet the specification cont ained in their particular Microchip Data Sheet.
- Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used i n the intended manner and under normal conditions.
- There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
- Microchip is willing to work with the customer who is concerned about the integrity of their code.
- Neither Microchip nor any other semiconduc tor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” Code protection is constantly evolving. We at Microchip are co mmitted to continuously improvin g the code protection features of our products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company’s quality system processes and procedures are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified. QUALITY MANAGEMENT S YSTEM CERTIFIED BY DNV == ISO/TS 16949 ==
DS20005049D-page 22 2011-2014 Microchip Technology Inc. AMERICAS Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://www.microchip.com/ support Web Address: www.microchip.com Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Austin, TX Tel: 512-257-3370 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Cleveland Independence, OH Tel: 216-447-0464 Fax: 216-447-0643 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Novi, MI Tel: 248-848-4000 Houston, TX Tel: 281-894-5983 Indianapolis Noblesville, IN Tel: 317-773-8323 Fax: 317-773-5453 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 New York, NY Tel: 631-435-6000 San Jose, CA Tel: 408-735-9110 Canada - Toronto Tel: 905-673-0699 Fax: 905-673-6509 ASIA/PACIFIC Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2943-5100 Fax: 852-2401-3431 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8569-7000 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 China - Chongqing Tel: 86-23-8980-9588 Fax: 86-23-8980-9500 China - Hangzhou Tel: 86-571-8792-8115 Fax: 86-571-8792-8116 China - Hong Kong SAR Tel: 852-2943-5100 Fax: 852-2401-3431 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 China - Shenzhen Tel: 86-755-8864-2200 Fax: 86-755-8203-1760 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 ASIA/PACIFIC India - Bangalore Tel: 91-80-3090-4444 Fax: 91-80-3090-4123 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 India - Pune Tel: 91-20-3019-1500 Japan - Osaka Tel: 81-6-6152-7160 Fax: 81-6-6152-9310 Japan - Tokyo Tel: 81-3-6880- 3770 Fax: 81-3-6880-3771 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 Taiwan - Hsin Chu Tel: 886-3-5778-366 Fax: 886-3-5770-955 Taiwan - Kaohsiung Tel: 886-7-213-7830 Taiwan - Taipei Tel: 886-2-2508-8600 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 EUROPE Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 France - Paris Germany - Dusseldorf Tel: 49-2129-3766400 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Germany - Pforzheim Tel: 49-7231-424750 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Italy - Venice Tel: 39-049-7625286 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Poland - Warsaw Tel: 48-22-3325737 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 Sweden - Stockholm Tel: 46-8-5090-4654 UK - Wokingham Tel: 44-118-921-5800 Fax: 44-118-921-5820 Worldwide Sales and Service 03/25/14