MCCS142236

MCCS142236 ONSEMI | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 5

Technical content

© Semiconductor Components Industries, LLC, 2010 February, 2010 − Rev. 6

1 Publication Order Number:

(110Ω) With Voltage Regulator The MCCS142236 is a precision 18 −bit switchable active SCSI−2 bus terminator with an on −board 2.85V regulator. When the Disconnect pin is LOW according to the truth table below, the MCCS142236 provides 110 Ω ±5% precision resistor pull −ups to a 2.85V reference for termination of 18 −bits in a SCSI−2 standard bus system interface. When the Disconnect pin is HIGH, the device outputs are in the high impedance state on all 18 bits. The regulator is also turned off, greatly reducing standby power. Even with no Termpwr applied, the outputs remain in the high impedance state.

• Complies With SCSI and SCSI−2 Standards
• Pin Compatible With UC5601, UC5602 and UC5608
• For Opposite Disconnect Polarity See ON Semiconductor’s MCCS142238
• 18 Switchable 110Ω Terminating Resistors
• 4pF Channel Capacitance During Disconnect
• Fully Supports Active Negation (Sinks Minimum of 220mA)
• Built−In 2.85V Regulator With Low Dropout V oltage
• Very Low Supply Current When Resistors Are Disabled (30μA Max)
• −650mA Source Current
• Thermal Shutdown Protection
• Thin Profile Surface Mount Package: 28−Lead SOIC The regulator has a guaranteed dropout voltage of less than 900mV , allowing regulation of supply voltages less than 4.0V . The MCCS142236 is protected by thermal shutdown. Other features include low disconnect current (30μA), over 220mA of active negation current sink capability, and 4pF disconnect capacitance. In 8−bit SCSI applications (“A” cable), only one MCCS142236 is needed at each end of the SCSI cable in order to terminate the 18 active signal lines. In 16 −bit WIDE SCSI applications (“P” cable), either two MCCS142236s, one each of the MCCS142236 and MCCS142237, or three MCCS142237s would be needed at each end of the SCSI cable in order to properly terminate the 27 active signal lines. The MCCS142237 is a 9−bit version of the MCCS142236. For information on “Power Dissipation for Active SCSI Terminators,” refer to ON Semiconductor Application Note AN1408/D, available through ON Semiconductor Fax System, or through the ON Semiconductor Literature Distribution Center. TRUTH TABLE Disconnect Output

0 Terminated

http://onsemi.com 18−BIT SWITCHABLE ACTIVE SCSI−2 BUS TERMINATOR DW SUFFIX 28−LEAD SOIC WIDE CASE 751F−05

Figure 1. 28−Lead Pinout (Top View)

• Pins 7, 8, 9, 20, 21 and 22 are heat-sink grounds.

Pin 28 is the signal ground. open, causing all outputs to be high impedance. providing 110Ω impedance to each of the bus lines. level. The supply source in this case could be Termpwr or VCC. outputs to be high impedance. impedance to each of the bus lines. Recommended Operating Conditions.

http://onsemi.com RECOMMENDED OPERATING CONDITIONS Symbol Parameter Min Max Unit Termpwr DC Supply Voltage 3.8 5.25 V Vin DC Input Voltage (Disconnect Pin) 0 Termpwr V VLine Signal Line Voltage 0 5.0 V TA Operating Temperature Range 0 +70 °C tr, tf Input Rise/Fall Time 0 500 ns ELECTRICAL CHARACTERISTICS (Unless otherwise stated, these specifications apply for TA = 0° to 70°C, Termpwr = 4.75V, Disconnect = Ground) Symbol Characteristic Min Typ Max Unit Condition Supply Current Section ITermpwr Termpwr Supply Current 15 410 465 mA All Termination Lines = Open All Termination Lines = 0.5V Ipd Power Down Mode Current 10 30 μA Disconnect = Open Output Section (Termination Lines) R110 Termination Impedance 104.5 110.0 115.5 Ω VOH Output HIGH Voltage 2.8 2.85 3.0 V Note 1. Isource Source Current Capability per Line −19.9 −24 mA Signal Line = 0.5V IOZ Output Leakage Current Signal Lines = 0 to 5.25V 1 μA Termpwr = 5.25V, Reg = Open, Disconnect = 4V CO Output Capacitance (Note 2.) 4.0 5.0 pF Disconnect = Open Regulator Section VReg Regulator Voltage 2.8 2.85 3.0 V Signal Lines = 0V or 4V Linereg Line Regulation 27 40 mV Signal Lines Open, Termpwr = 4V to 6V Loadreg Load Regulation 35 60 mV Signal Lines = 0V to 3V VDO Drop Out Voltage 0.7 0.9 V Signal Lines = 0.5V ILim Current Limit −450 −650 −850 mA Reg = 0V Isink Current Sink Capability 220 350 400 mA Reg = 3.5V Tshut Thermal Shutdown 150 °C Disconnect Section DTH Disconnect Threshold (Note 2.) 1.1 1.3 1.7 V IIL Input Leakage Current 100 120 μA Disconnect = 0V 1. Measured with one output high and all other signal lines open. 2. Not production tested, guaranteed by design. AC CHARACTERISTICS (Note 3., Reg = 2.85, CL = 2.2μF, tr = tf = 6ns) Symbol Parameters 0°C to + 70°C Unit t(connect) Max Connect Time, High Impedance to Termination, Disconnect to Outputs 100 μs t(disconnect) Max Disconnect Time, Termination to High Impedance, Disconnect to Outputs 20 μs 3. Not production tested, guaranteed by design.

http://onsemi.com PACKAGE DIMENSIONS DW SUFFIX PLASTIC SOIC PACKAGE CASE 751F−05 ISSUE G B SXM0.025 Y ST M0.25 Y M SEATING PLANE A DIM MIN MAX MILLIMETERS A 2.35 2.65 A1 0.13 0.29 B 0.35 0.49 C 0.23 0.32 D 17.80 18.05 E 7.40 7.60 G 1.27 BSC H 10.05 10.55 L 0.41 0.90 M 0 8 /C0095/C0095L C PIN 1 IDENT D E H 0.10 −X− −Y− G −T− M NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS D AND E DO NOT INCLUDE MOLD PROTRUSION 4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. 5. DIMENSION B DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBER PR5OTRUSION SHALL NOT BE 0.13 TOTATL IN EXCESS OF B DIMENSION AT MAXIMUM MATERIAL CONDITION. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, direct ly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5773−3850 MCCS142236/D LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: orderlit@onsemi.com ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative