MC9328MX1_06 FREESCALE | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 100
Technical content
© Freescale Semiconductor, Inc., 2004, 2005, 2006. All rights reserved. Freescale Semiconductor Data Sheet: Technical Data Freescale reserves the right to change the detail specifications as may be required to permit improvements in the design of its products. Document Number: MC9328MX1 Rev. 7, 12/2006 MC9328MX1
Package Information
(MAPBGA–225)
Ordering Information
1 Introduction
The i.MX Family of applications processors provides a leap in performance with an ARM9™ microprocessor core and highly integrated system functions. The i.MX family specifically addresses the requirements of the personal, portable product market by providing intelligent integrated peripherals, an advanced processor core, and power management capabilities. The MC9328MX1 (i.MX1) processor features the advanced and power-efficient ARM920T™ core that operates at speeds up to 200 MHz. Integrated modules, which include a USB device, an LCD controller, and an MMC/SD host controller, support a suite of peripherals to enhance portable products seeking to provide a rich multimedia experience. It is packaged in a 256-contact Mold Array Process-Ball Grid Array (MAPBGA). Figure 1 shows the functional block diagram of the i.MX1 processor.
Contents
4 Functional Description and Application
2 Freescale Semiconductor
Figure 1. i.MX1 Functional Block Diagram
1.1 Features
- ARM920T™ Microprocessor Core
- AHB to IP Bus Interfaces (AIPIs)
- External Interface Module (EIM)
- SDRAM Controller (SDRAMC)
- DPLL Clock and Power Control Module
- Three Universal Asynchronous Receiver/Tran smitters (UART 1, UART 2, and UART3)
- Two Serial Peripheral Interfaces (SPI1 and SPI2)
- Two General-Purpose 32-bit Counters/Timers
- Watchdog Timer
- Real-Time Clock/Sampling Timer (RTC)
- LCD Controller (LCDC)
- Pulse-Width Modulation (PWM) Module
- Universal Serial Bus (USB) Device
- Multimedia Card and Secure Digita l (MMC/SD) Host Controller Module
- Memory Stick® Host Controller (MSHC)
- Direct Memory Access Controller (DMAC)
- Two Synchronous Serial Interfaces and an Inter-IC Sound (SSI1 and SSI2/I 2S) Module
- I n t e r - I C ( I2C) Bus Module
- V i d e o P o r t Watchdog GPIO LCD Controller JTAG/ICE CGM Timer 1 & 2 PWM Standard Bootstrap Connectivity System Control I2C MMC/SD SPI 1 and UART 1 UART 2 & 3 USB Device SmartCard I/F Bluetooth Memory Stick® SSI/I2S 1 & 2 Analog Signal Human Interface Video Port Multimedia Multimedia Power RTC BusDMAC InterruptVMMU CPU Complex I Cache AIPI 1 AIPI 2 D Cache eSRAMEIM & ARM9TDMI™ System I/O Control (DPLLx2) Controller Control(11 Chnl) (128K)SDRAMCAccelerator Accelerator Processor SPI 2 Host Controller MC9328MX1
- General-Purpose I/O (GPIO) Ports
- Bootstrap Mode
- Analog Signal Processing (ASP) Module
- Bluetooth™ Accelerator (BTA)
- Multimedia Accelerator (MMA)
- Power Management Features
- Operating V oltage Range: 1.7 V to 1.9 V core, 1.7 V to 3.3 V I/O
- 256-pin MAPBGA Package
1.2 Target Applications
AccompliTM 008 GSM/GPRS interactive communicator.
1.3 Ordering Information
Table 1 provides ordering information.
1.4 Conventions
- OVERBAR is used to indicate a signal that is active when pulled low: for example, RESET.
- Logic level one is a voltage that corresponds to Boolean true (1) state.
- Logic level zero is a voltage that corresponds to Boolean false (0) state.
- T o set a bit or bits means to establish logic level one.
- T o clear a bit or bits means to establish logic level zero.
- A signal is an electronic construct whose state conveys or changes in state convey information.
- A pin is an external physical connection. The same pin can be used to connect a number of signals.
- Asserted means that a discrete signal is in active logic state. — Active low signals change from logic level one to logic level zero. — Active high signals change from logic level zero to logic level one.
Table 1. Ordering Information
150 MHz 0°C to 70°C Pb-free MC9328MX1VM15(R2)
4 Freescale Semiconductor
- Negated means that an asserted discrete signal changes logic state. — Active low signals change from logic level zero to logic level one. — Active high signals change from logic level one to logic level zero.
- LSB means least significant bit or bits, and MSB means most significant bit or bits. References to low and high bytes or words are spelled out.
- Numbers preceded by a percent sign (%) are binary. Numbers preceded by a dollar sign ($) or 0x are hexadecimal.
2 Signals and Connections
are grouped by the internal module that they are connected to. Table 2. i.MX1 Signal Descriptions EB0 MSB Byte Strobe—Active low external enable byte signal that controls D [31:24]. EB1 Byte Strobe—Active low external enable byte signal that controls D [23:16]. EB2 Byte Strobe—Active low external enable byte signal that controls D [15:8]. EB3 LSB Byte Strobe—Active low external enable byte signal that controls D [7:0]. OE Memory Output Enable—Active low ou tput enables external data bus. Function Multiplexing Control Register (FMCR). By default CSD [1:0] is selected. on-going burst sequence and initiate a new (long first access) burst sequence. BCLK (burst clock) Clock signal sent to external synchronous memories (such as burst flash) during burst mode. terminated by the external DTACK signal after 1022 clock counts have elapsed. reset is determined by the settings of these pins. are logically equivalent to core address p_addr [25:21] in SDRAM cycles.
signals are logically equivalent to core address p_addr [12:9] in SDRAM cycles. by programming the system control register. chip-select by properly configuring BOOT [3:0] input pins. CLKO Clock Out signal selected from internal clock signals. modules (except the reset module and the clock control module) are reset. following sources: Power-on reset, External reset (RESET_IN), and Watchdog time-out. generated by an external RC circuit designed to detect a power-up event. TRST Test Reset Pin—External active low signal used to asynchronously initialize the JTAG controller. TDO Serial Output for test instructions and data. Changes on the falling edge of TCK. TDI Serial Input for test instructions and data. Sampled on the rising edge of TCK. TCK Test Clock to synchronize test logic and control register access through the JTAG port. Table 2. i.MX1 Signal Descriptions (Continued)
6 Freescale Semiconductor
DMA_REQ DMA Request—external DMA request signal. Multiplexed with SPI1_SPI_RDY. change state after power-on reset negates or during chip operation. ETMTRACESYNC ETM sync signal which is multiplexed with A24. ETMTRACESYNC is selected in ETM mode. ETMTRACECLK ETM clock signal which is multiplexed with A23. ETMTRACECLK is selected in ETM mode. ETMTRACEPKT [7:0] ETM packet signals which are multiplexed with ECB, LBA, BCLK (burst clock), PA17, A [19:16]. ETMTRACEPKT [7:0] are selected in ETM mode. LD [15:0] LCD Data Bus—All LCD signals are driven low after reset and when LCD is off. driver (dedicated signal SPS for Sharp panel HR-TFT). ACD/OE Alternate crystal direction/output enable. CONTRAST This signal is used to control the LCD bias voltage as contrast control. SPL_SPR Program horizontal scan direction (Sharp panel dedicated signal). PS Control signal output for source driver (Sharp panel dedicated signal). REV Signal for common electrode driving signal preparation (Sharp panel dedicated signal).
the MC9328MX1 Reference Manual for information about how to bring this signal to the assigned pin. the MC9328MX1 Reference Manual for information about how to bring this signal to the assigned pin. MC9328MX1 Reference Manual for information about how to bring this signal to the assigned pin. MC9328MX1 Reference Manual for information about how to bring this signal to the assigned pin. enable register, a 4.7K–69K external pull up resistor must be added.
8 Freescale Semiconductor
register, a 50K–69K external pull up resistor must be added. purposes, not for use in application mode.
10 Freescale Semiconductor
2.1 I/O Pads Power Supply and Signal Multiplexing Scheme
configuring the appropriate GPIO registers when those pins are multiplexed to provide different functions.
Table 3. MC9328MX1 Signal Multiplexing Scheme
12 Freescale Semiconductor
Table 3. MC9328MX1 Signal Multiplexing Scheme (Continued)
14 Freescale Semiconductor
16 Freescale Semiconductor
18 Freescale Semiconductor
20 Freescale Semiconductor
1 After reset, CS0 goes H/L depends on BOOT[3:0]. 2 Need external circuitry to drive the signal. 4 External resistor is needed. 5 Need external pull-up or pull-down. 6 ASP signals are clamped by AVDD2 to prevent ESD (electrostatic discharge) damage. AVDD2 must be greater than QVDD to keep diodes reverse-biased.
Electrical Characteristics
MC9328MX1 Technical Data, Rev. 7
22 Freescale Semiconductor
3 Electrical Characteristics
This section contains the electrical specifications and timing diagrams for the i.MX1 processor.
3.1 Maximum Ratings
Table 4 provides information on maximum ratings which are those values beyond which damage to the device may occur. Functional operation should be restricted to the limits listed in Recommended Operating Range Table 5 on page 23 or the DC Characteristics table.
3.2 Recommended Operating Range
Table 5 provides the recommended operating ranges for the supply voltages and temperatures. The i.MX1 processor has multiple pairs of VDD and VSS power supply and return pins. QVDD and QVSS pins are used for internal logic. All other VDD and VSS pins are for the I/O pads voltage supply, and each pair of VDD and VSS provides power to the enclosed I/O pads. This design allows different peripheral supply voltage levels in a system. Because A VDD pins are supply voltages to the analog pads, it is recommended to isolate and noise-filter the A VDD pins from other VDD pins. BTRFVDD is the supply voltage for the Bluetooth interface signals. It is quite sensitive to the data transmit/receive accuracy. Please refer to Bluetooth RF spec for special handling. If Bluetooth is not used Table 4. Maximum Ratings core-that is, 7x GPIO, 15x Data bus, and 8x Address bus.
MC9328MX1 Technical Data, Rev. 7 Freescale Semiconductor 23 in the system, these Bluetooth pins can be used as general purpose I/O pins and BTRFVDD can be used as other NVDD pins. For more information about I/O pads grouping per VDD, please refer to Table 2 on page 4.
3.3 Power Sequence Requirements
For required power-up and power-down sequencing, please refer to the “Power-Up Sequence” section of application note AN2537 on the i.MX applications processor website.
3.4 DC Electrical Characteristics
Table 6 contains both maximum and minimum DC characteristics of the i.MX1 processor. Table 5. Recommended Operating Range
1 Standby current
MC9328MX1 Technical Data, Rev. 7
24 Freescale Semiconductor
3.5 AC Electrical Characteristics
The AC characteristics consist of output delays, input setup and hold times, and signal skew times. All signals are specified relative to an appropriate edge of other signals. All timing specifications are specified at a system operating frequency from 0 MHz to 96 MHz (core operating frequency 150 MHz) with an operating supply voltage from VDD min to VDD max under an operating temperature from TL to TH. All timing is measured at 30 pF loading. Sidd4 Standby current (Core = 150 MHz, QVDD = 2.0V, temp = 55°C) –6 0 – μA VIH Input high voltage 0.7V DD –V d d + 0 . 2 V VIL Input low voltage – – 0.4 V VOH Output high voltage (IOH = 2.0 mA) 0.7V DD –V d d V VOL Output low voltage (IOL = -2.5 mA) – – 0.4 V IIL Input low leakage current (VIN = GND, no pull-up or pull-down) ––± 1 μA IIH Input high leakage current (VIN =V DD, no pull-up or pull-down) ––± 1 μA IOH Output high current (VOH =0 . 8 VDD, VDD =1 . 8 V ) 4.0 – – mA IOL Output low current (VOL =0 . 4 V , VDD =1 . 8 V ) -4.0 – – mA IOZ Output leakage current (Vout =V DD, output is high impedance) ––± 5 μA Ci Input capacitance – – 5 pF Co Output capacitance – – 5 pF Table 7. Tristate Signal Timing Table 8. 32k/16M Oscillator Signal Timing Table 6. Maximum and Minimum DC Characteristics (Continued)
4 Functional Description and Application Information
4.1 Embedded Trace Macrocell
- 32-bit data field
- 7-bit address field
- A read/write bit The data to be written is scanned into the 32-bit data field, the address of the register into the 7-bit address field, and a 1 into the read/write bit. A register is read by scanning its address into the address field and a 0 into the read/write bit. The 32-bit data field is ignored. A read or a write takes place when the TAP controller enters the UPDATE-DR state. The timing diagram for the ETM9 is shown in Figure 2. See Table 9 for the ETM9 timing parameters used in Figure 2.
Figure 2. Trace Port Timing Diagram 1 The 16 MHz oscillator is not recommended for use in new designs. Table 8. 32k/16M Oscillator Signal Timing (Continued)
26 Freescale Semiconductor
4.2 DPLL Timing Specifications
pre-divider and Tdck is the output double clock period. Table 9. Trace Port Timing Diagram Parameter Table
1 CLK frequency 0 85 0 100 MHz
Table 10. DPLL Specifications
4.3 Reset Module
Figure 3. Timing Relationship with POR Table 10. DPLL Specifications (Continued)
28 Freescale Semiconductor
Figure 4. Timing Relationship with RESET_IN
4.4 External Interface Module
EIM is shown in Figure 5, and Table 12 defines the parameters of signals. Table 11. Reset Module Timing Parameter Table
1 Width of input POWER_ON_RESET note1
for use with CMOS oscillators, crystal manufacturers have developed a working knowledge of start-up time of their crystals. Typically, start-up times range from 400 ms to 1.2 seconds for this type of crystal. calculating timing for the start-up process.
2 Width of internal POWER_ON_RESET
5 Width of external hard-reset RESET_IN 4 – 4 – Cycles of
Figure 5. EIM Bus Timing Diagram Table 12. EIM Bus Timing Parameter Table
30 Freescale Semiconductor
4.4.1 DTACK Signal Description
supports DTACK signal function when the external DTACK signal is used for data acknowledgement.
4.4.2 DTACK Signal Timing
of measure for this figure are found in the associated tables.
1 Clock refers to the system clock signal, HCLK, generated from the System DPLL
Table 12. EIM Bus Timing Parameter Table (Continued)
4.4.2.1 WAIT Read Cycle without DMA
Figure 6. WAIT Read Cycle without DMA Table 13. WAIT Read Cycle without DMA: WSC = 111111, DTACK_SEL=1, HCLK=96MHz
4 Wait asserted after OE asserted – 1020T ns
7 Data ready after wait asserted 0 T ns
10 Become low after CS5 asserted 0 1019T ns
11 Wait pulse width 1T 1020T ns
- T is the system clock period. (For 96 MHz system clock, T=10.42 ns)
EBC bit in CS5L register is clear.
- Address becomes valid and CS
asserts at the start of read access cycle.
- The external wait input requirement is eliminated when CS5 is programmed to use internal wait state.
32 Freescale Semiconductor
4.4.2.2 WAIT Read Cycle DMA Enabled
Figure 7. DTACK WAIT Read Cycle DMA Enabled Table 14. DTACK WAIT Read Cycle DMA Enabled: WSC = 111111, DTACK_SEL=1, HCLK=96MHz
5 Wait asserted after CS5 asserted – 1020T ns
8 Data ready after wait is asserted – T ns
11 Wait becomes low after CS5 asserted 0 1019T ns
4.4.2.3 WAIT Write Cycle without DMA
Figure 8. WAIT Write Cycle without DMA
12 Wait pulse width 1T 1020T ns
- T is the system clock period. (For 96 MHz system clock, T=10.42 ns)
- OE and EB assertion time is programmable by OEA bit in CS5L register. EB assertion in read cycle will occur only when
EBC bit in CS5L register is clear.
- Address becomes valid and CS asserts at the start of read access cycle.
- The external wait input requirement is eliminated when CS5 is programmed to use internal wait state.
Table 15. WAIT Write Cycle without DMA: WSC = 111111, DTACK_SEL=1, HCLK=96MHz
6 Wait asserted after CS5 asserted – 1020T ns
Table 14. DTACK WAIT Read Cycle DMA Enabled: WSC = 111111, DTACK_SEL=1, HCLK=96MHz (Continued)
34 Freescale Semiconductor
4.4.2.4 WAIT Write Cycle DMA Enabled
Figure 9. WAIT Write Cycle DMA Enabled
9 Data ready after CS5 is asserted – T ns
- T is the system clock period. (For 96 MHz system clock, T=10.42 ns)
- CS5 assertion can be controlled by CSA bits. EB assertion can also be programmable by WEA bits in CS5L register.
- Address becomes valid and RW asserts at the start of write access cycle.
- The external wait input requirement is eliminated when CS5 is programmed to use internal wait state.
Table 15. WAIT Write Cycle without DMA: WSC = 111111, DTACK_SEL=1, HCLK=96MHz (Continued)
4.4.3 EIM External Bus Timing
in Figure 5, and Table 12 defines the parameters of signals. Table 16. WAIT Write Cycle DMA Enabled: WSC = 111111, DTACK_SEL=1, HCLK=96MHz
1 C S 5 assertion time See note 2 – ns
10 CS deactive to next CS active T – ns
12 Wait becomes low after CS5 asserted 0 1019T ns
13 Wait pulse width 1T 1020T ns
- T is the system clock period. (For 96 MHz system clock, T=10.42 ns)
- CS5 assertion can be controlled by CSA bits. EB assertion also can be programmable by WEA bits in CS5L register.
- Address becomes valid and RW asserts at the start of write access cycle.
4.The external wait input requirement is eliminated when CS5 is programmed to use internal wait state.
36 Freescale Semiconductor
Figure 10. WSC = 1, A.HALF/E.HALF
Figure 11. WSC = 1, WEA = 1, WEN = 1, A.HALF/E.HALF
38 Freescale Semiconductor
Figure 12. WSC = 1, OEA = 1, A.WORD/E.HALF
Figure 13. WSC = 1, WEA = 1, WEN = 2, A.WORD/E.HALF
40 Freescale Semiconductor
Figure 14. WSC = 3, OEA = 2, A.WORD/E.HALF
Figure 15. WSC = 3, WEA = 1, WEN = 3, A.WORD/E.HALF
42 Freescale Semiconductor
Figure 16. WSC = 3, OEA = 4, A.WORD/E.HALF
Figure 17. WSC = 3, WEA = 2, WEN = 3, A.WORD/E.HALF
44 Freescale Semiconductor
Figure 18. WSC = 3, OEN = 2, A.WORD/E.HALF
Figure 19. WSC = 3, OEA = 2, OEN = 2, A.WORD/E.HALF
46 Freescale Semiconductor
Figure 20. WSC = 2, WWS = 1, WEA = 1, WEN = 2, A.WORD/E.HALF
Figure 21. WSC = 1, WWS = 2, WEA = 1, WEN = 2, A.WORD/E.HALF
48 Freescale Semiconductor
Figure 22. WSC = 2, WWS = 2, WEA = 1, WEN = 2, A.HALF/E.HALF
Figure 23. WSC = 2, WWS = 1, WEA = 1, WEN = 2, EDC = 1, A.HALF/E.HALF
50 Freescale Semiconductor
Figure 24. WSC = 2, CSA = 1, WWS = 1, A.WORD/E.HALF
Figure 25. WSC = 3, CSA = 1, A.HALF/E.HALF
52 Freescale Semiconductor
Figure 26. WSC = 2, OEA = 2, CNC = 3, BCM = 1, A.HALF/E.HALF
Figure 27. WSC = 2, OEA = 2, WEA = 1, WEN = 2, CNC = 3, A.HALF/E.HALF
54 Freescale Semiconductor
Figure 28. WSC = 3, SYNC = 1, A.HALF/E.HALF
Figure 29. WSC = 2, SYNC = 1, DOL = [1/0], A.WORD/E.WORD
56 Freescale Semiconductor
Figure 30. WSC = 2, SYNC = 1, DOL = [1/0], A.WORD/E.HALF
Figure 31. WSC = 7, OEA = 8, SYNC = 1, DOL = 1, BCD = 1, BCS = 2, A.WORD/E.HALF
58 Freescale Semiconductor
Figure 32. WSC = 7, OEA = 8, SYNC = 1, DOL = 1, BCD = 1, BCS = 1, A.WORD/E.HALF
4.4.4 Non-TFT Panel Timing
Figure 33. Non-TFT Panel Timing
4.5 Pen ADC Specifications
The specifications for the pen ADC are shown in Table 18 through Table 20. Table 17. Non TFT Panel Timing Diagram 1 Maximum frequency of LCDC_CLK is 48 MHz, which is controlled by Peripheral Clock Divider Register. 2 Maximum frequency of SCLK is HCLK / 5, otherwise LD output will be wrong. these 3 signals are active high. 4 Tpix is the pixel clock period which equals LCDC_CLK period * (PCD + 1). 5 Ts is the shift clock period. Ts = Tpix * (panel data bus width). Table 18. Pen ADC System Performance
60 Freescale Semiconductor
4.6 ASP Touch Panel Controller
of parameters and their corresponding measuring conditions are mentioned as well.
4.6.1 Electrical Specifications
Test conditions: Temperature = 25º C, QVDD = 1800mV . Note that QVDD should be 1800mV. Table 19. Pen ADC Test Conditions Table 20. Pen ADC Absolute Rating Table 21. ASP Touch Panel Controller Electrical Spec
4.6.2 Gain Calculations
Figure 34. Gain Calculations Where V is input, S is output, G is the slope, and C is the y-intercept.
4.6.3 Offset Calculations
Figure 35. Offset Calculations Where V is input, S is output, G is the slope, and C is the y-intercept.
62 Freescale Semiconductor
4.6.4 Gain Error Calculations
Gain error calculations are made using the information in this section. Figure 36. Gain Error Calculations
4.7 Bluetooth Accelerator
Bluetooth chip interfaced to a UART is recommended. shown in Figure 37 and Figure 38, and the associated parameters shown in Table 22 and Table 23.
Figure 37. MC13180 Data Bus Timing Diagram Table 22. MC13180 Data Bus Timing Parameter Table
1 FrameSync setup time relati ve to BT CLK rising edge1
1 Please refer to 2.4 GHz RF Transceiver Module (MC13180) Technical Data documentation.
2 FrameSync hold time relative to BT CLK rising edge 1 –1 2– n s
3 Receive Data setup time relative to BT CLK rising edge 1 –6– n s
4 Receive Data hold time rela tive to BT CLK rising edge1 –1 3– n s
5 Transmit Data setup time relative to RXTX_EN rising edge 2
RF_Status (0x0021605C) registers.
7 BT CLK duty cycle 40 – 60 %
8 Transmit Data hold time relative to RXTX_EN falling edge 4 – 10 µs
64 Freescale Semiconductor
Figure 38. SPI Interface Timing Diagram Using MC13180
4.8 SPI Timing Diagrams
different triggering mechanisms. Table 23. SPI Interface Timing Parameter Table Using MC13180
1 SPI_EN setup time relative to rising edge of SPI_CLK 15 – ns
2 Transmit data delay time relative to rising edge of SPI_CLK 0 15 ns
3 Transmit data hold time relative to rising edge of SPI_EN 0 15 ns
4 SPI_CLK rise time 0 25 ns
5 SPI_CLK fall time 0 25 ns
6 SPI_EN hold time relative to falling edge of SPI_CLK 15 – ns
7 Receive data setup time relative to falling edge of SPI_CLK
SPI_Control (0x00216138) register together with system clock.
8 Receive data hold time relative to falling edge of SPI_CLK 1 15 – ns
9 SPI_CLK frequency, 50% duty cycle required 1 –2 0 M H z
66 Freescale Semiconductor
Figure 44. SPI SCLK Timing Diagram
4.9 LCD Controller
Figure 45. SCLK to LD Timing Diagram Table 24. Timing Parameter Table for Figure 39 through Figure 43
1 SPI_RDY to SS output low 2T1
1 T = CSPI system clock period (PERCLK2).
3 Last SCLK edge to SS output high 2 Tsclk – ns
3 WAIT = Number of bit clocks (SCLK) or 32.768 kHz clocks per Sample Period Control Register. Table 25. Timing Parameter Table for SPI SCLK
8 SCLK frequency 0 10 MHz
9 SCLK pulse width 100 – ns
Figure 46. 4/8/16 Bit/Pixel TFT Color Mode Panel Timing Table 26. LCDC SCLK Timing Parameter Table
1 SCLK to LD valid – 2 ns
Table 27. 4/8/16 Bit/Pixel TFT Color Mode Panel Timing
68 Freescale Semiconductor
4.10 Multimedia Card/Secure Digital Host Controller
MMC/SD module (inner system) and the application (user programming). Figure 47. Chip-Select Read Cycle Timing Diagram
22 T s
11 T s
- Ts is the SCLK period which equals LCDC_C LK / (PCD + 1). Normally LCDC_CLK = 15ns.
- VSYN, HSYN and OE can be programmed as active high or active low. In Figure 46, all 3 signals are active low.
- The polarity of SCLK and LD[ 15:0] can also be programmed.
- SCLK can be programmed to be deactivated during the VSYN pulse or the OE deasserted period. In Figure 46, SCLK is always active.
- For T9 non-display region, VSYN is non-act ive. It is used as an reference.
- XMAX is defined in pixels.
Table 27. 4/8/16 Bit/Pixel TFT Color Mode Panel Timing (Continued)
4.10.1 Command Response Timing on MMC/SD Bus
Figure 52 are defined in Table 29. Table 28. SDHC Bus Timing Parameter Table
1 CLK frequency at Data transfer Mode
1 CL ≤ 100 pF / 250 pF (10/30 cards)
2 CLK frequency at Identification Mode 2
2 CL ≤ 250 pF (21 cards)
3 CL ≤ 25 pF (1 card)
7 Output delay time 3 0 16 0 14 ns
Table 29. State Signal Parameters for Figure 48 through Figure 52
70 Freescale Semiconductor
Figure 48. Timing Diagrams at Identification Mode responding card. The other two diagrams show the separating periods NRC and NCC. Figure 49. Timing Diagrams at Data Transfer Mode data stops two clock cycles after the end bit of the stop command.
72 Freescale Semiconductor
Figure 51. Timing Diagrams at Data Write different scenarios on the bus.
Figure 52. Stop Transmission During Different Scenarios Table 30. Timing Values for Figure 48 through Figure 52 Stop transmission received after last data block. Card becomes busy programming. Stop transmission received after last data block. Card becomes busy programming.
74 Freescale Semiconductor
4.10.2 SDIO-IRQ and ReadWait Service Handling
continues until the source is removed (SD_DAT[1] returns to its high level). Figure 53. SDIO IRQ Timing Diagram Table 30. Timing Values for Figure 48 through Figure 52 (Continued)
Figure 54. SDIO ReadWait Timing Diagram
4.11 Memory Stick Host Controller
either four-state or two-state access mode. completed within one packet length (in four-state access mode). and BS1 bus states are automatically repeated to avoid a bus collision on the SDIO.
76 Freescale Semiconductor
Figure 55. MSHC Signal Timing Diagram Table 31. MSHC Signal Timing Parameter Table
1 MS_SCLKI frequency – 25 MHz
2 MS_SCLKI high pulse width 20 – ns
3 MS_SCLKI low pulse width 20 – ns
4 MS_SCLKI rise time – 3 ns
5 MS_SCLKI fall time – 3 ns
6 MS_SCLKO frequency
7 MS_SCLKO high pulse width 1 20 – ns
8 MS_SCLKO low pulse width 1 15 – ns
9 MS_SCLKO rise time 1 –5 n s
10 MS_SCLKO fall time 1 –5 n s
11 MS_BS delay time 1 –3 n s
4.12 Pulse-Width Modulator
Figure 56 and the parameters are listed in Table 32. Figure 56. PWM Output Timing Diagram
12 MS_SDIO output delay time 1,2 –3 n s
13 MS_SDIO input setup time for MS_SCLKO rising edge (RED bit = 0) 3 18 – ns
14 MS_SDIO input hold time for MS_SCLKO rising edge (RED bit = 0) 3 0– n s
15 MS_SDIO input setup time for MS_SCLKO falling edge (RED bit = 1) 4 23 – ns
16 MS_SDIO input hold time for MS_SCLKO falling edge (RED bit = 1) 4 0– n s
1 Loading capacitor condition is less than or equal to 30pF . 3 If the MSC2[RED] bit = 0, MSHC samples MS_SDIO input data at MS_SCLKO rising edge. 4 If the MSC2[RED] bit = 1, MSHC samples MS_SDIO input data at MS_SCLKO falling edge. Table 32. PWM Output Timing Parameter Table
1 System CLK frequency 1 08 70 1 0 0 M H z
Table 31. MSHC Signal Timing Parameter Table (Continued)
78 Freescale Semiconductor
4.13 SDRAM Controller
random access memory) Controller. Figure 57. SDRAM Read Cycle Timing Diagram
1 CL of PWMO = 30 pF
Table 32. PWM Output Timing Parameter Table (Continued) Note: CKE is high during the read/write cycle.
Table 33. SDRAM Read Timing Parameter Table
2 SDRAM clock low-level width
5 SDRAM access time (CL = 1) – 22 – 22 ns
7 Data out high-impedance time (CL = 1) – 22 – 22 ns
8 Active to read/write command period (RC = 1) t
1 tRCD = SDRAM clock cycle time. This settings can be found in the MC9328MX1 reference manual.
80 Freescale Semiconductor
Figure 58. SDRAM Write Cycle Timing Diagram Table 34. SDRAM Write Timing Parameter Table
2 SDRAM clock low-level width 6–4– n s
6 Precharge cycle period
1 Precharge cycle timing is included in the write timing diagram. 2 tRP and tRCD = SDRAM clock cycle time. These settings can be found in the MC9328MX1 reference manual.
7 Active to read/write command delay t RCD2 –t RCD2 –n s
Figure 59. SDRAM Refresh Timing Diagram Table 35. SDRAM Refresh Timing Parameter Table
6 Precharge cycle period t
1 tRP and tRC = SDRAM clock cycle time. These settings can be found in the MC9328MX1 reference manual.
7 Auto precharge command period t RC1 –t RC1 –n s
82 Freescale Semiconductor
Figure 60. SDRAM Self-Refresh Cycle Timing Diagram
4.14 USB Device Port
covers the transfer modes and how they work from the ground up. bandwidth at all times, there is no end-of-transfer.
Figure 61. USB Device Timing Diagram for Data Transfer to USB Transceiver (TX) Table 36. USB Device Timing Parameters for Data Transfer to USB Transceiver (TX)
84 Freescale Semiconductor
Figure 62. USB Device Timing Diagram for Data Transfer from USB Transceiver (RX)
4.15 I 2C Module
Direction, Slave Acknowledge, Data, Data Acknowledge, and STOP. Figure 63. Definition of Bus Timing for I2C Table 37. USB Device Timing Parameter Table for Data Transfer from USB Transceiver (RX)
4.16 Synchronous Serial Interface
mode, the transmitter and receiver each have their own clock and frame synchronization signals. are shown in Figure 65 through Figure 67. communicate with a wide variety of devices. Figure 64. SSI Transmitter Internal Clock Timing Diagram Table 38. I2C Bus Timing Parameter Table
1 Hold time (repeated) START condition 182 – 160 – ns
2 Data hold time 01 7 101 5 0 n s
4 HIGH period of the SCL clock 80 – 120 – ns
5 LOW period of the SCL clock 480 – 320 – ns
Note: SRXD input in synchronous mode only.
86 Freescale Semiconductor
Figure 65. SSI Receiver Internal Clock Timing Diagram Figure 66. SSI Transmitter External Clock Timing Diagram
Figure 67. SSI Receiver External Clock Timing Diagram Table 39. SSI (Port C Primary Function) Timing Parameter Table
14 SRXD hold time after SRCK low 0 – 0 – ns
88 Freescale Semiconductor
30 SRXD hole time after SRCK low 0 – 0 – ns
32 SRXD hold after STCK falling 0 – 0 – ns
34 SRXD hold after STCK falling 0 – 0 – ns
the clock signal STCK/SRCK and/or the frame sync STFS/SRFS shown in the tables and in the figures. 3 bl = bit length; wl = word length. Table 39. SSI (Port C Primary Function) Timing Parameter Table (Continued)
Table 40. SSI (Port B Alternate Function) Timing Parameter Table
18 STCK high to STFS (bl) high
90 Freescale Semiconductor
30 SRXD hold time after SRCK low 0 – 0 – ns
the clock signal STCK/SRCK and/or the frame sync STFS/SRFS shown in the tables and in the figures. FMCR register bits in the Clock controller module (CRM). By default, the input are selected from Port C primary function. 3 bl = bit length; wl = word length. Table 41. SSI 2 (Port C Alternate Function) Timing Parameter Table Table 40. SSI (Port B Alternate Function) Timing Parameter Table (Continued)
by inverting the clock signal STCK/SRCK and/or the frame sync STFS/SRFS shown in the tables and in the figures. Table 41. SSI 2 (Port C Alternate Function) Timing Parameter Table (Continued)
92 Freescale Semiconductor
4.17 CMOS Sensor Interface
FIFO, and a 16 × 32 statistic data FIFO.
4.17.1 Gated Clock Mode
data in negative edge. The parameters for the timing diagrams are listed in Table 42. Figure 68. Sensor Output Data on Pixel Clock Falling Edge from Port C alternate function.
Figure 69. Sensor Output Data on Pixel Clock Rising Edge For example: Given pixel clock period = 10ns, duty cycle = 50 / 50, hold time = 1ns, setup time = 1ns. Table 42. Gated Clock Mode Timing Parameters
94 Freescale Semiconductor
4.17.2 Non-Gated Clock Mode
data in negative edge. The parameters for the timing diagrams are listed in Table 43. Figure 70. Sensor Output Data on Pixel Clock Falling Edge Figure 71. Sensor Output Data on Pixel Clock Rising Edge Table 43. Non-Gated Clock Mode Parameters
For example: Given pixel clock period = 10ns, duty cycle = 50 / 50, hold time = 1ns, setup time = 1ns. Table 43. Non-Gated Clock Mode Parameters (Continued)
96 Freescale Semiconductor
5 Pin-Out and Package Information
Multiplexing Table 3 on page 11. Table 44. i.MX1 256 MAPBGA Pin Assignments 1 ASP signals are clamped by AVDD2 to prevent ESD (Electrostatic Discharge) damage. AVDD2 must be greater than QVDD to keep diodes reversed-biased. 2 This signal is not used and should be floated in an actual application.
5.1 MAPBGA 256 Package Dimensions
Figure 72 illustrates the 256 MAPBGA 14 mm × 14 mm × 1.30 mm package, with an 0.8 mm pad pitch. The device designator for the MAPBGA package is VH. Figure 72. i.MXL 256 MAPBGA Mechanical Drawing
- ALL DIMENSIONS ARE IN MILLIMETERS.
2.INTERPRET DIMENSIONS AND TOLERANCES PER ASME Y14 5M-1994. 3.MAXIMUM SOLDER BALL DIAMETER MEASURED PARALLEL TO DATUM A.
- DATUM A, THE SEATING PLANE IS DEFINED BY SPHERICAL CROWNS OF THE SOLDER BALLS.
98 Freescale Semiconductor
6 Product Documentation
6.1 Revision History
and not stylistic or grammatical changes.
6.2 Reference Documents
Table 45. i.MX1 Data Sheet Revision History Rev. 7 Added the DMA_REQ signal to table. Changed AVDD2 references to QVDD, except for C14. Added footnote regarding ESD. Changed occurrence of SD_SCLK to SD_CLK. Table 3 on page 11 Added Signal Multiplex table.
MC9328MX1 Technical Data, Rev. 7 Freescale Semiconductor 99
Document Number: MC9328MX1 Rev. 7 How to Reach Us: Home Page: www.freescale.com E-mail: support@freescale.com USA/Europe or Locations Not Listed: Freescale Semiconductor Technical Information Center, CH370 1300 N. Alma School Road Chandler, Arizona 85224 +1-800-521-6274 or +1-480-768-2130 support@freescale.com Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) support@freescale.com Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku, Tokyo 153-0064, Japan 0120 191014 or +81 3 5437 9125 support.japan@freescale.com Asia/Pacific: Freescale Semiconductor Hong Kong Ltd. Technical Information Center
2 Dai King Street
Tai Po, N.T., Hong Kong +800 2666 8080 support.asia@freescale.com For Literature Requests Only: Freescale Semiconductor Literature Distribution Center P .O. Box 5405 Denver, Colorado 80217 1-800-521-6274 or 303-675-2140 Fax: 303-675-2150 LDCForFreescaleSemiconductor@hibbertgroup.com Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”, must be validated for each customer application by customer’s technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. ARM and the ARM POWERED logo are the registered trademarks of ARM Limited. ARM9, ARM920T, and ARM9TDMI are the trademarks of ARM Limited. All other product or service names are the property of their respective owners. © Freescale Semiconductor, Inc. 2006. All rights reserved. RoHS-compliant and/or Pb-free versions of Freescale products have the functionality and electrical characteristics of their non-RoHS-compliant and/or non-Pb-free counterparts. For further information, see http://www.freescale.com or contact your Freescale sales representative. For information on Freescale’s Environmental Products program, go to http://www.freescale.com/epp.