MC7805BD2TR4

MC7800_10 ONSEMI | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 33

Technical content

Features

• Output Current in Excess of 1.0 A
• No External Components Required
• Internal Thermal Overload Protection
• Internal Short Circuit Current Limiting
• Output Transistor Safe−Area Compensation
• Output V oltage Offered in 1.5%, 2% and 4% Tolerance
• Available in Surface Mount D2PAK−3, DPAK−3 and Standard 3−Lead Transistor Packages
• NCV Prefix for Automotive and Other Applications Requiring Site and Control Changes
• Pb−Free Packages are Available MAXIMUM RATINGS (TA = 25°C, unless otherwise noted) Rating Symbol Value Unit 369C 221A 936 Input Voltage (5.0 − 18 V) (24 V) VI 35 Vdc Power Dissipation PD Internally Limited W Thermal Resistance, Junction−to−Ambient R/C0113JA 92 65 Figure °C/W Thermal Resistance, Junction−to−Case R/C0113JC 5.0 5.0 5.0 °C/W Storage Junction Temperature Range Tstg −65 to +150 °C Operating Junction Temperature TJ +150 °C Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. *This device series contains ESD protection and exceeds the following tests: Human Body Model 2000 V per MIL_STD_883, Method 3015. Machine Model Method 200 V. TO−220−3 T SUFFIX CASE 221AB D2PAK−3 D2T SUFFIX CASE 936 See detailed ordering and shipping information in the package dimensions section on page 23 of this data sheet.

ORDERING INFORMATION

connected to Pin 2. Pin 1. Input 2. Ground 3. Output Heatsink surface (shown as terminal 4 in case outline drawing) is connected to Pin 2. STANDARD APPLICATION A common ground is required between the input and the output voltages. The input voltage must remain typically 2.0 V above the output voltage even during the low point on the input ripple voltage. XX, MC78XXInput C in* 0.33 /C0109F CO** Output These two digits of the type number indicate nominal voltage. Cin is required if regulator is located an appreciable distance from power supply filter. CO is not needed for stability; however, it does improve transient response. Values of less than 0.1 /C0109F could cause instability. See general marking information in the device marking section on page 30 of this data sheet. DEVICE MARKING INFORMATION DPAK−3 DT SUFFIX CASE 369C http://onsemi.com 1 2

30 PC2

Figure 1. Representative Schematic Diagram This device contains 22 active transistors.

MC7800, MC7800A, MC7800AE, NCV7800 http://onsemi.com ELECTRICAL CHARACTERISTICS (Vin = 10 V, IO = 500 mA, TJ = Tlow to 125°C (Note 1), unless otherwise noted) Characteristic Symbol MC7805B, NCV7805 MC7805C UnitMin Typ Max Min Typ Max Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤15 W)

7.0 Vdc ≤ Vin ≤ 20 Vdc

8.0 Vdc ≤ Vin ≤ 20 Vdc

4.75 5.0 5.25 4.75 5.0 5.25 Vdc Line Regulation (Note 4) 7.5 Vdc ≤ Vin ≤ 20 Vdc, 1.0 A

8.0 Vdc ≤ Vin ≤ 12 Vdc

5.0 1.3 100 0.5 0.8 mV Load Regulation (Note 4) 5.0 mA ≤ IO ≤ 1.0 A 5.0 mA ≤ IO ≤ 1.5 A (TA = 25°C) Regload 1.3 0.15 100 1.3 1.3 mV Quiescent Current IB − 3.2 8.0 − 3.2 6.5 mA Quiescent Current Change

7.0 Vdc ≤ Vin ≤ 25 Vdc

5.0 mA ≤ IO ≤ 1.0 A (TA = 25°C) /C0068IB 0.5 0.3 0.08 1.0 0.8 mA Ripple Rejection

8.0 Vdc ≤ Vin ≤ 18 Vdc, f = 120 Hz

RR − 68 − 62 83 − dB Dropout Voltage (IO = 1.0 A, TJ = 25°C) VI − VO − 2.0 − − 2.0 − Vdc Output Noise Voltage (TA = 25°C)

10 Hz ≤ f ≤ 100 kHz

Vn − 10 − − 10 − /C0109V/VO Output Resistance f = 1.0 kHz rO − 0.9 − − 0.9 − m/C0087 Short Circuit Current Limit (TA = 25°C) Vin = 35 Vdc Peak Output Current (TJ = 25°C) Imax − 2.2 − − 2.2 − A Average Temperature Coefficient of Output Voltage TCVO − −0.3 − − −0.3 − mV/°C 1. T low =0 °C for MC78XXC, MC78XXAC, = /C004240°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB 2. Load and line regulation are specified at constant junction temperature. Changes in V O due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used.

MC7800, MC7800A, MC7800AE, NCV7800 http://onsemi.com ELECTRICAL CHARACTERISTICS (Vin = 10 V, IO = 1.0 A, TJ = Tlow to 125°C (Note 3), unless otherwise noted) MC7805AB/MC7805AC/NCV7805AB Characteristic Symbol Min Typ Max Unit Output Voltage (TJ = 25°C) VO 4.9 5.0 5.1 Vdc Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤15 W)

7.5 Vdc ≤ Vin ≤ 20 Vdc

VO 4.8 5.0 5.2 Vdc Line Regulation (Note 4) Regline mV 7.5 Vdc ≤ Vin ≤ 25 Vdc, IO = 500 mA − 0.5 10 8.0 Vdc ≤ Vin ≤ 12 Vdc, IO = 1.0 A − 0.8 12 8.0 Vdc ≤ Vin ≤ 12 Vdc, IO = 1.0 A, TJ = 25°C − 1.3 4.0 7.3 Vdc ≤ Vin ≤ 20 Vdc, IO = 1.0 A, TJ = 25°C − 4.5 10 Load Regulation (Note 4) Regload mV 5.0 mA ≤ IO ≤ 1.5 A, TJ = 25°C − 1.3 25 5.0 mA ≤ IO ≤ 1.0 A − 0.8 25 250 mA ≤ IO ≤ 750 mA − 0.53 15 Quiescent Current IB − 3.2 6.0 mA Quiescent Current Change /C0068IB mA 8.0 Vdc ≤ Vin ≤ 25 Vdc, IO = 500 mA − 0.3 0.8 7.5 Vdc ≤ Vin ≤ 20 Vdc, TJ = 25°C − − 0.8 5.0 mA ≤ IO ≤ 1.0 A − 0.08 0.5 Ripple Rejection

8.0 Vdc ≤ Vin ≤ 18 Vdc, f = 120 Hz, IO = 500 mA

RR 68 83 − dB Dropout Voltage (IO = 1.0 A, TJ = 25°C) VI − VO − 2.0 − Vdc Output Noise Voltage (TA = 25°C) Vn − 10 − /C0109V/VO Output Resistance (f = 1.0 kHz) rO − 0.9 − m/C0087 Short Circuit Current Limit (TA = 25°C) Vin = 35 Vdc ISC − 0.2 − A Peak Output Current (TJ = 25°C) Imax − 2.2 − A Average Temperature Coefficient of Output Voltage TCVO − −0.3 − mV/°C 3. T low =0 °C for MC78XXC, MC78XXAC, = /C004240°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB 4. Load and line regulation are specified at constant junction temperature. Changes in V O due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used.

MC7800, MC7800A, MC7800AE, NCV7800 http://onsemi.com ELECTRICAL CHARACTERISTICS (Vin = 11 V, IO = 500 mA, TJ = Tlow to 125°C (Note 5), unless otherwise noted) Characteristic Symbol MC7806B/NCV7806B MC7806C UnitMin Typ Max Min Typ Max Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤15 W) VO Vdc 8.0 Vdc ≤ Vin ≤ 21 Vdc − − − 5.7 6.0 6.3 9.0 Vdc ≤ Vin ≤ 21 Vdc 5.7 6.0 6.3 − − − Line Regulation, TJ = 25°C (Note 6) Regline mV 8.0 Vdc ≤ Vin ≤ 25 Vdc − 5.5 120 − 0.5 24 9.0 Vdc ≤ Vin ≤ 13 Vdc − 1.4 60 − 0.8 12 Load Regulation, TJ = 25°C (Note 6) Regload − 1.3 120 − 1.3 30 mV 5.0 mA ≤ IO ≤ 1.5 A Quiescent Current (TJ = 25°C) IB − 3.3 8.0 − 3.3 8.0 mA Quiescent Current Change /C0068IB mA 8.0 Vdc ≤ Vin ≤ 25 Vdc − − − − 0.3 1.3 Ripple Rejection RR − 65 − 58 65 − dB

9.0 Vdc ≤ Vin ≤ 19 Vdc, f = 120 Hz

Dropout Voltage (IO = 1.0 A, TJ = 25°C) VI − VO − 2.0 − − 2.0 − Vdc Output Noise Voltage (TA = 25°C) Vn − 10 − − 10 − /C0109V/VO Output Resistance f = 1.0 kHz rO − 0.9 − − 0.9 − m/C0087 Short Circuit Current Limit (TA = 25°C) ISC − 0.2 − − 0.2 − A Vin = 35 Vdc Peak Output Current (TJ = 25°C) Imax − 2.2 − − 2.2 − A Average Temperature Coefficient of Output Voltage 5. T low =0 °C for MC78XXC, MC78XXAC, = /C004240°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB 6. Load and line regulation are specified at constant junction temperature. Changes in V O due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used.

MC7800, MC7800A, MC7800AE, NCV7800 http://onsemi.com ELECTRICAL CHARACTERISTICS (Vin = 11 V, IO = 1.0 A, TJ = Tlow to 125°C (Note 7), unless otherwise noted) MC7806AC Characteristic Symbol Min Typ Max Unit Output Voltage (TJ = 25°C) VO 5.88 6.0 6.12 Vdc

8.6 Vdc ≤ Vin ≤ 21 Vdc

Line Regulation (Note 8) Regline mV 8.6 Vdc ≤ Vin ≤ 25 Vdc, IO = 500 mA − 5.0 12 9.0 Vdc ≤ Vin ≤ 13 Vdc, IO = 1.0 A − 1.4 15 Load Regulation (Note 8) Regload mV 5.0 mA ≤ IO ≤ 1.5 A, TJ = 25°C − 1.3 25 5.0 mA ≤ IO ≤ 1.0 A − 0.9 25 250 mA ≤ IO ≤ 750 mA − 0.2 15 Quiescent Current IB − 3.3 6.0 mA Quiescent Current Change /C0068IB mA 9.0 Vdc ≤ Vin ≤ 25 Vdc, IO = 500 mA − − 0.8 9.0 Vdc ≤ Vin ≤ 21 Vdc, IO = 1.0 A, TJ = 25°C − − 0.8 Ripple Rejection RR 58 65 − dB

9.0 Vdc ≤ Vin ≤ 19 Vdc, f = 120 Hz, IO = 500 mA

Dropout Voltage (IO = 1.0 A, TJ = 25°C) VI − VO − 2.0 − Vdc Output Noise Voltage (TA = 25°C) Vn − 10 − /C0109V/VO Output Resistance (f = 1.0 kHz) rO − 0.9 − m/C0087 Short Circuit Current Limit (TA = 25°C) ISC − 0.2 − A Vin = 35 Vdc Peak Output Current (TJ = 25°C) Imax − 2.2 − A Average Temperature Coefficient of Output Voltage TCVO − −0.3 − mV/°C 7. T low =0 °C for MC78XXC, MC78XXAC, = /C004240°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB 8. Load and line regulation are specified at constant junction temperature. Changes in V O due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used.

MC7800, MC7800A, MC7800AE, NCV7800 http://onsemi.com ELECTRICAL CHARACTERISTICS (Vin = 14 V, IO = 500 mA, TJ = Tlow to 125°C (Note 9), unless otherwise noted) MC7808B/NCV7808B MC7808C Characteristic Symbol Min Typ Max Min Typ Max Unit Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤15 W) VO Vdc 10.5 Vdc ≤ Vin ≤ 23 Vdc − − − 7.6 8.0 8.4 11.5 Vdc ≤ Vin ≤ 23 Vdc 7.6 8.0 8.4 − − − Line Regulation, TJ = 25°C, (Note 10) Regline mV 10.5 Vdc ≤ Vin ≤ 25 Vdc − 6.0 160 − 6.0 32 11 Vdc ≤ Vin ≤ 17 Vdc − 1.7 80 − 1.7 16 Load Regulation, TJ = 25°C (Note 10) Regload − 1.4 160 − 1.4 35 mV 5.0 mA ≤ IO ≤ 1.5 A Quiescent Current IB − 3.3 8.0 − 3.3 8.0 mA Quiescent Current Change /C0068IB mA 10.5 Vdc ≤ Vin ≤ 25 Vdc − − − − − 1.0 Ripple Rejection RR − 62 − 56 62 − dB

11.5 Vdc ≤ Vin ≤ 18 Vdc, f = 120 Hz

Dropout Voltage (IO = 1.0 A, TJ = 25°C) VI − VO − 2.0 − − 2.0 − Vdc Output Noise Voltage (TA = 25°C) Vn − 10 − − 10 − /C0109V/VO Output Resistance f = 1.0 kHz rO − 0.9 − − 0.9 − m/C0087 Short Circuit Current Limit (TA = 25°C) ISC − 0.2 − − 0.2 − A Vin = 35 Vdc Peak Output Current (TJ = 25°C) Imax − 2.2 − − 2.2 − A Average Temperature Coefficient of Output Voltage TCVO − −0.4 − − −0.4 − mV/°C 9. T low =0 °C for MC78XXC, MC78XXAC, = /C004240°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB 10.Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used.

MC7800, MC7800A, MC7800AE, NCV7800 http://onsemi.com ELECTRICAL CHARACTERISTICS (Vin = 14 V, IO = 1.0 A, TJ = Tlow to 125°C (Note 11), unless otherwise noted) Characteristic Symbol MC7808AB/MC7808AC MC7808AEB UnitMin Typ Max Min Typ Max Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤15 W)

10.6 Vdc ≤ Vin ≤ 23 Vdc

Line Regulation (Note 12)

10.6 Vdc ≤ Vin ≤ 25 Vdc, IO = 500 mA

11 Vdc ≤ Vin ≤ 17 Vdc, IO = 1.0 A

10.4 Vdc ≤ Vin ≤ 23 Vdc, TJ = 25°C

6.0 1.7 5.0 6.0 1.7 5.0 mV Load Regulation (Note 12) 5.0 mA ≤ IO ≤ 1.5 A, TJ = 25°C 5.0 mA ≤ IO ≤ 1.0 A 250 mA ≤ IO ≤ 750 mA Regload 1.4 1.0 0.22 1.4 1.0 0.22 mV Quiescent Current IB − 3.3 6.0 − 3.3 6.0 mA Quiescent Current Change

11 Vdc ≤ Vin ≤ 25 Vdc, IO = 500 mA

10.6 Vdc ≤ Vin ≤ 23 Vdc, IO = 1.0 A, TJ = 25°C 5.0 mA ≤ IO ≤ 1.0 A /C0068IB 0.8 0.8 0.5 0.8 0.8 0.5 mA Ripple Rejection 11.5 Vdc ≤ Vin ≤ 21.5 Vdc, f = 120 Hz, IO = 500 mA RR 56 62 − 56 62 − dB Dropout Voltage (IO = 1.0 A, TJ = 25°C) VI − VO − 2.0 − − 2.0 − Vdc Output Noise Voltage (TA = 25°C) Vn − 10 − − 10 − /C0109V/VO Output Resistance f = 1.0 kHz rO − 0.9 − − 0.9 − m/C0087 Short Circuit Current Limit (TA = 25°C) Vin = 35 Vdc Peak Output Current (TJ = 25°C) Imax − 2.2 − − 2.2 − A Average Temperature Coefficient of Output Voltage TCVO − −0.4 − − −0.4 − mV/°C 11. Tlow =0 °C for MC78XXC, MC78XXAC, = /C004240°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB 12.Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used.

MC7800, MC7800A, MC7800AE, NCV7800 http://onsemi.com ELECTRICAL CHARACTERISTICS (Vin = 15 V, IO = 500 mA, TJ = Tlow to 125°C (Note 13), unless otherwise noted) MC7809B MC7809C Characteristic Symbol Min Typ Max Min Typ Max Unit Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤15 W) VO Vdc Line Regulation, TJ = 25°C (Note 14) Regline mV 11 Vdc ≤ Vin ≤ 26 Vdc − 6.2 32 − 6.2 32 11.5 Vdc ≤ Vin ≤ 17 Vdc − 1.8 16 − 1.8 16 Load Regulation, TJ = 25°C (Note 14) Regload − 1.5 35 − 1.5 35 mV 5.0 mA ≤ IO ≤ 1.5 A Quiescent Current IB − 3.4 8.0 − 3.4 8.0 mA Quiescent Current Change /C0068IB mA 11.5 Vdc ≤ Vin ≤ 26 Vdc − − 1.0 − − 1.0 Ripple Rejection RR 56 61 − 56 61 − dB 11.5 Vdc ≤ Vin ≤ 21.5 Vdc, f = 120 Hz Dropout Voltage (IO = 1.0 A, TJ = 25°C) VI − VO − 2.0 − − 2.0 − Vdc Output Noise Voltage (TA = 25°C) Vn − 10 − − 10 − /C0109V/VO Output Resistance f = 1.0 kHz rO − 1.0 − − 1.0 − m/C0087 Short Circuit Current Limit (TA = 25°C) ISC − 0.2 − − 0.2 − A Vin = 35 Vdc Peak Output Current (TJ = 25°C) Imax − 2.2 − − 2.2 − A Average Temperature Coefficient of Output Voltage TCVO − −0.5 − − −0.5 − mV/°C 13.Tlow =0 °C for MC78XXC, MC78XXAC, = /C004240°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB 14.Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used.

MC7800, MC7800A, MC7800AE, NCV7800 http://onsemi.com ELECTRICAL CHARACTERISTICS (Vin = 15 V, IO = 1.0 A, TJ = Tlow to 125°C (Note 15), unless otherwise noted) Characteristic Symbol MC7809AB/MC7809AC UnitMin Typ Max Output Voltage (TJ = 25°C) VO 8.82 9.0 9.18 Vdc Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤ 15 W)

11.5 Vdc ≤ Vin ≤ 24 Vdc

VO 8.65 9.0 9.35 Vdc Line Regulation (Note 16)

11.5 Vdc ≤ Vin ≤ 26 Vdc, IO = 500 mA

12 Vdc ≤ Vin ≤ 17 Vdc, IO = 1.0 A

11.5 Vdc ≤ Vin ≤ 24 Vdc, TJ = 25°C

6.2 1.8 5.2 7.0 mV Load Regulation (Note 16) 5.0 mA ≤ IO ≤ 1.5 A, TJ = 25°C 5.0 mA ≤ IO ≤ 1.0 A 250 mA ≤ IO ≤ 750 mA Regload mV Quiescent Current IB − 3.3 6.0 mA Quiescent Current Change 11.5 Vdc ≤ Vin ≤ 24 Vdc, IO = 1.0 A, TJ = 25°C 5.0 mA ≤ IO ≤ 1.0 A /C0068IB 0.8 0.8 0.5 mA Ripple Rejection 11.5 Vdc ≤ Vin ≤ 21.5 Vdc, f = 120 Hz, IO = 500 mA RR 56 61 − dB Dropout Voltage (IO = 1.0 A, TJ = 25°C) VI _ VO 2.0 Vdc Output Noise Voltage (TA = 25°C) − 10 − /C0109V/VO Output Resistance f = 1.0 kHz rO − 1.0 − m/C0087 Short Circuit Current Limit (TA = 25°C) Vin = 35 Vdc ISC − 0.2 A Peak Output Current (TJ = 25°C) Imax − 2.2 − A Average Temperature Coefficient of Output Voltage TCVO − −0.5 − mV/°C 15.Tlow =0 °C for MC78XXC, MC78XXAC, = /C004240°C for NCV78XX, MC78XXB, MC78XXAB. 16.Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used.

MC7800, MC7800A, MC7800AE, NCV7800 http://onsemi.com ELECTRICAL CHARACTERISTICS (Vin = 19 V, IO = 500 mA, TJ = Tlow to 125°C (Note 17), unless otherwise noted) MC7812B/NCV7812B MC7812C Characteristic Symbol Min Typ Max Min Typ Max Unit Output Voltage (TJ = 25°C) VO 11.5 12 12.5 11.5 12 12.5 Vdc Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤15 W) VO Vdc 14.5 Vdc ≤ Vin ≤ 27 Vdc − − − 11.4 12 12.6 15.5 Vdc ≤ Vin ≤ 27 Vdc 11.4 12 12.6 − − − Line Regulation, TJ = 25°C (Note 18) Regline mV 14.5 Vdc ≤ Vin ≤ 30 Vdc − 7.5 240 − 3.8 24 16 Vdc ≤ Vin ≤ 22 Vdc − 2.2 120 − 0.3 24 14.8 Vdc ≤ Vin ≤ 27 Vdc, IO = 1.0 A − − − − − 48 Load Regulation, TJ = 25°C (Note 18) Regload − 1.6 240 − 8.1 60 mV 5.0 mA ≤ IO ≤ 1.5 A Quiescent Current IB − 3.4 8.0 − 3.4 6.5 mA Quiescent Current Change /C0068IB mA 14.5 Vdc ≤ Vin ≤ 30 Vdc, IO = 1.0 A, TJ = 25°C − − − − − 0.7 15 Vdc ≤ Vin ≤ 30 Vdc − − 1.0 − − 0.8 Ripple Rejection RR − 60 − 55 60 − dB

15 Vdc ≤ Vin ≤ 25 Vdc, f = 120 Hz

Dropout Voltage (IO = 1.0 A, TJ = 25°C) VI − VO − 2.0 − − 2.0 − Vdc Output Noise Voltage (TA = 25°C) Vn − 10 − − 10 − /C0109V/VO Output Resistance f = 1.0 kHz rO − 1.1 − − 1.1 − m/C0087 Short Circuit Current Limit (TA = 25°C) ISC − 0.2 − − 0.2 − A Vin = 35 Vdc Peak Output Current (TJ = 25°C) Imax − 2.2 − − 2.2 − A Average Temperature Coefficient of Output Voltage TCVO − −0.8 − − −0.8 − mV/°C 17.Tlow =0 °C for MC78XXC, MC78XXAC, = /C004240°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB 18.Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used.

MC7800, MC7800A, MC7800AE, NCV7800 http://onsemi.com ELECTRICAL CHARACTERISTICS (Vin = 19 V, IO = 1.0 A, TJ = Tlow to 125°C (Note 19), unless otherwise noted) MC7812AB/MC7812AC/NCV7812AB Characteristic Symbol Min Typ Max Unit Output Voltage (TJ = 25°C) VO 11.75 12 12.25 Vdc Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤15 W) VO 11.5 12 12.5 Vdc

14.8 Vdc ≤ Vin ≤ 27 Vdc

Line Regulation (Note 20) Regline mV 14.8 Vdc ≤ Vin ≤ 30 Vdc, IO = 500 mA − 3.8 18 16 Vdc ≤ Vin ≤ 22 Vdc, IO = 1.0 A − 2.2 20 14.5 Vdc ≤ Vin ≤ 27 Vdc, TJ = 25°C − 6.0 120 Load Regulation (Note 20) Regload mV 5.0 mA ≤ IO ≤ 1.5 A, TJ = 25°C − − 25 5.0 mA ≤ IO ≤ 1.0 A − − 25 Quiescent Current IB − 3.4 6.0 mA Quiescent Current Change /C0068IB mA 15 Vdc ≤ Vin ≤ 30 Vdc, IO = 500 mA − − 0.8 14.8 Vdc ≤ Vin ≤ 27 Vdc, TJ = 25°C − − 0.8 Ripple Rejection RR 55 60 − dB

15 Vdc ≤ Vin ≤ 25 Vdc, f = 120 Hz, IO = 500 mA

Dropout Voltage (IO = 1.0 A, TJ = 25°C) VI − VO − 2.0 − Vdc Output Noise Voltage (TA = 25°C) Vn − 10 − /C0109V/VO Output Resistance (f = 1.0 kHz) rO − 1.1 − m/C0087 Short Circuit Current Limit (TA = 25°C) ISC − 0.2 − A Vin = 35 Vdc Peak Output Current (TJ = 25°C) Imax − 2.2 − A Average Temperature Coefficient of Output Voltage TCVO − −0.8 − mV/°C 19.Tlow =0 °C for MC78XXC, MC78XXAC, = /C004240°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB 20.Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used.

MC7800, MC7800A, MC7800AE, NCV7800 http://onsemi.com ELECTRICAL CHARACTERISTICS (Vin = 23 V, IO = 500 mA, TJ = Tlow to 125°C (Note 21), unless otherwise noted) MC7815B/NCV7815B MC7815C Characteristic Symbol Min Typ Max Min Typ Max Unit Output Voltage (TJ = 25°C) VO 14.4 15 15.6 14.4 15 15.6 Vdc Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤15 W) VO Vdc 17.5 Vdc ≤ Vin ≤ 30 Vdc − − − 14.25 15 15.75 18.5 Vdc ≤ Vin ≤ 30 Vdc 14.25 15 15.75 − − − Line Regulation, TJ = 25°C (Note 22) Regline mV 17.9 Vdc ≤ Vin ≤ 30 Vdc − 8.5 300 − 8.5 30 20 Vdc ≤ Vin ≤ 26 Vdc − 3.0 150 − 3.0 28 Load Regulation, TJ = 25°C (Note 22) Regload − 1.8 300 − 1.8 55 mV 5.0 mA ≤ IO ≤ 1.5 A Quiescent Current IB − 3.5 8.0 − 3.5 6.5 mA Quiescent Current Change /C0068IB mA 17.5 Vdc ≤ Vin ≤ 30 Vdc − − − − − 0.8 17.5 Vdc ≤ Vin ≤ 30 Vdc, IO = 1.0 A, TJ = 25°C − − 1.0 − − 0.7 Ripple Rejection RR − 58 − 54 58 − dB 18.5 Vdc ≤ Vin ≤ 28.5 Vdc, f = 120 Hz Dropout Voltage (IO = 1.0 A, TJ = 25°C) VI − VO − 2.0 − − 2.0 − Vdc Output Noise Voltage (TA = 25°C) Vn − 10 − − 10 − /C0109V/VO Output Resistance f = 1.0 kHz rO − 1.2 − − 1.2 − m/C0087 Short Circuit Current Limit (TA = 25°C) ISC − 0.2 − − 0.2 − A Vin = 35 Vdc Peak Output Current (TJ = 25°C) Imax − 2.2 − − 2.2 − A Average Temperature Coefficient of Output Voltage TCVO − −1.0 − − −1.0 − mV/°C 21.Tlow =0 °C for MC78XXC, MC78XXAC, = /C004240°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB 22.Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used.

MC7800, MC7800A, MC7800AE, NCV7800 http://onsemi.com ELECTRICAL CHARACTERISTICS (Vin = 23 V, IO = 1.0 A, TJ = Tlow to 125°C (Note 23), unless otherwise noted) MC7815AB/MC7815AC Characteristic Symbol Min Typ Max Unit Output Voltage (TJ = 25°C) VO 14.7 15 15.3 Vdc Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤15 W) VO 14.4 15 15.6 Vdc

17.9 Vdc ≤ Vin ≤ 30 Vdc

Line Regulation (Note 24) Regline mV 17.9 Vdc ≤ Vin ≤ 30 Vdc, IO = 500 mA − 8.5 20 20 Vdc ≤ Vin ≤ 26 Vdc − 3.0 22 17.5 Vdc ≤ Vin ≤ 30 Vdc, IO = 1.0 A, TJ = 25°C − 7.0 20 Load Regulation (Note 24) Regload mV 5.0 mA ≤ IO ≤ 1.5 A, TJ = 25°C − 1.8 25 5.0 mA ≤ IO ≤ 1.0 A − 1.5 25 250 mA ≤ IO ≤ 750 mA − 1.2 15 Quiescent Current IB − 3.5 6.0 mA Quiescent Current Change /C0068IB mA 17.5 Vdc ≤ Vin ≤ 30 Vdc, IO = 500 mA − − 0.8 17.5 Vdc ≤ Vin ≤ 30 Vdc, IO = 1.0 A, TJ = 25°C − − 0.8 Ripple Rejection RR 60 80 − dB 18.5 Vdc ≤ Vin ≤ 28.5 Vdc, f = 120 Hz, IO = 500 mA Dropout Voltage (IO = 1.0 A, TJ = 25°C) VI − VO − 2.0 − Vdc Output Noise Voltage (TA = 25°C) Vn − 10 − /C0109V/VO Output Resistance f = 1.0 kHz rO − 1.2 − m/C0087 Short Circuit Current Limit (TA = 25°C) ISC − 0.2 − A Vin = 35 Vdc Peak Output Current (TJ = 25°C) Imax − 2.2 − A Average Temperature Coefficient of Output Voltage TCVO − −1.0 − mV/°C 23.Tlow =0 °C for MC78XXC, MC78XXAC, = /C004240°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB 24.Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used.

MC7800, MC7800A, MC7800AE, NCV7800 http://onsemi.com ELECTRICAL CHARACTERISTICS (Vin = 27 V, IO = 500 mA, TJ = Tlow to 125°C (Note 25), unless otherwise noted) MC7818B MC7818C Characteristic Symbol Min Typ Max Min Typ Max Unit Output Voltage (TJ = 25°C) VO 17.3 18 18.7 17.3 18 18.7 Vdc Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤15 W) VO Vdc 21 Vdc ≤ Vin ≤ 33 Vdc − − − 17.1 18 18.9 22 Vdc ≤ Vin ≤ 33 Vdc 17.1 18 18.9 − − − Line Regulation, (Note 26) Regline mV 21 Vdc ≤ Vin ≤ 33 Vdc − 9.5 360 − 9.5 50 24 Vdc ≤ Vin ≤ 30 Vdc − 3.2 180 − 3.2 25 Load Regulation, (Note 26) Regload − 2.0 360 − 2.0 55 mV 5.0 mA ≤ IO ≤ 1.5 A Quiescent Current IB − 3.5 8.0 − 3.5 6.5 mA Quiescent Current Change /C0068IB mA 21 Vdc ≤ Vin ≤ 33 Vdc − − − − − 1.0 Ripple Rejection RR − 57 − 53 57 − dB

22 Vdc ≤ Vin ≤ 33 Vdc, f = 120 Hz

Dropout Voltage (IO = 1.0 A, TJ = 25°C) ViI − VO − 2.0 − − 2.0 − Vdc Output Noise Voltage (TA = 25°C) Vn − 10 − − 10 − /C0109V/VO Output Resistance f = 1.0 kHz rO − 1.3 − − 1.3 − m/C0087 Short Circuit Current Limit (TA = 25°C) ISC − 0.2 − − 0.2 − A Vin = 35 Vdc Peak Output Current (TJ = 25°C) Imax − 2.2 − − 2.2 − A Average Temperature Coefficient of Output Voltage TCVO − −1.5 − − −1.5 − mV/°C 25.Tlow =0 °C for MC78XXC, MC78XXAC, = /C004240°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB 26.Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used.

MC7800, MC7800A, MC7800AE, NCV7800 http://onsemi.com ELECTRICAL CHARACTERISTICS (Vin = 27 V, IO = 1.0 A, TJ = Tlow to 125°C (Note 27), unless otherwise noted) Characteristic Symbol MC7818AC UnitMin Typ Max Output Voltage (TJ = 25°C) VO 17.64 18 18.36 Vdc Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤15 W) VO 17.3 18 18.7 Vdc

21 Vdc ≤ Vin ≤ 33 Vdc

Line Regulation (Note 28) Regline mV 21 Vdc ≤ Vin ≤ 33 Vdc, IO = 500 mA − 9.5 22 24 Vdc ≤ Vin ≤ 30 Vdc, IO = 1.0 A − 3.2 25 24 Vdc ≤ Vin ≤ 30 Vdc, IO = 1.0 A, TJ = 25°C − 3.2 10.5 20.6 Vdc ≤ Vin ≤ 33 Vdc, IO = 1.0 A, TJ = 25°C − 8.0 22 Load Regulation (Note 28) Regload mV 5.0 mA ≤ IO ≤ 1.5 A, TJ = 25°C − 2.0 25 5.0 mA ≤ IO ≤ 1.0 A − 1.8 25 250 mA ≤ IO ≤ 750 mA − 1.5 15 Quiescent Current IB − 3.5 6.0 mA Quiescent Current Change /C0068IB mA 21 Vdc ≤ Vin ≤ 33 Vdc, IO = 500 mA − − 0.8 21.5 Vdc ≤ Vin ≤ 30 Vdc, TJ = 25°C − − 0.8 Ripple Rejection RR 53 57 − dB

22 Vdc ≤ Vin ≤ 32 Vdc, f = 120 Hz, IO = 500 mA

Dropout Voltage (IO = 1.0 A, TJ = 25°C) VI − VO − 2.0 − Vdc Output Noise Voltage (TA = 25°C) Vn − 10 − /C0109V/VO Output Resistance f = 1.0 kHz rO − 1.3 − m/C0087 Short Circuit Current Limit (TA = 25°C) ISC − 0.2 − A Vin = 35 Vdc Peak Output Current (TJ = 25°C) Imax − 2.2 − A Average Temperature Coefficient of Output Voltage TCVO − −1.5 − mV/°C 27.Tlow =0 °C for MC78XXC, MC78XXAC, = /C004240°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB 28.Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used.

MC7800, MC7800A, MC7800AE, NCV7800 http://onsemi.com ELECTRICAL CHARACTERISTICS (Vin = 33 V, IO = 500 mA, TJ = Tlow to 125°C (Note 29), unless otherwise noted) MC7824B MC7824C Characteristic Symbol Min Typ Max Min Typ Max Unit Output Voltage (TJ = 25°C) VO 23 24 25 23 24 25 Vdc Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤15 W) VO Vdc 27 Vdc ≤ Vin ≤ 38 Vdc − − − 22.8 24 25.2 28 Vdc ≤ Vin ≤ 38 Vdc 22.8 24 25.2 − − − Line Regulation, (Note 30) Regline mV 27 Vdc ≤ Vin ≤ 38 Vdc − 11.5 480 − 2.7 60 30 Vdc ≤ Vin ≤ 36 Vdc − 3.8 240 − 2.7 48 Load Regulation, (Note 30) Regload − 2.1 480 − 4.4 65 mV 5.0 mA ≤ IO ≤ 1.5 A Quiescent Current IB − 3.6 8.0 − 3.6 6.5 mA Quiescent Current Change /C0068IB mA 27 Vdc ≤ Vin ≤ 38 Vdc − − − − − 1.0 Ripple Rejection RR − 54 − 50 54 − dB

28 Vdc ≤ Vin ≤ 38 Vdc, f = 120 Hz

Dropout Voltage (IO = 1.0 A, TJ = 25°C) VI − VO − 2.0 − − 2.0 − Vdc Output Noise Voltage (TA = 25°C) Vn − 10 − − 10 − /C0109V/VO Output Resistance f = 1.0 kHz rO − 1.4 − − 1.4 − m/C0087 Short Circuit Current Limit (TA = 25°C) ISC − 0.2 − − 0.2 − A Vin = 35 Vdc Peak Output Current (TJ = 25°C) Imax − 2.2 − − 2.2 − A Average Temperature Coefficient of Output Voltage TCVO − −2.0 − − −2.0 − mV/°C 29.Tlow =0 °C for MC78XXC, MC78XXAC, = /C004240°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB 30.Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used.

MC7800, MC7800A, MC7800AE, NCV7800 http://onsemi.com ELECTRICAL CHARACTERISTICS (Vin = 33 V, IO = 1.0 A, TJ = Tlow to 125°C (Note 31), unless otherwise noted) MC7824AC Characteristic Symbol Min Typ Max Unit Output Voltage (TJ = 25°C) VO 23.5 24 24.5 Vdc Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤15 W) VO 23.2 24 25.8 Vdc

27.3 Vdc ≤ Vin ≤ 38 Vdc

Line Regulation (Note 32) Regline mV 27 Vdc ≤ Vin ≤ 38 Vdc, IO = 500 mA − 11.5 25 30 Vdc ≤ Vin ≤ 36 Vdc, IO = 1.0 A − 3.8 28 30 Vdc ≤ Vin ≤ 36 Vdc, TJ = 25°C − 3.8 12 26.7 Vdc ≤ Vin ≤ 38 Vdc, IO = 1.0 A, TJ = 25°C − 10 25 Load Regulation (Note 32) Regload mV 5.0 mA ≤ IO ≤ 1.5 A, TJ = 25°C − 2.1 15 5.0 mA ≤ IO ≤ 1.0 A − 2.0 25 250 mA ≤ IO ≤ 750 mA − 1.8 15 Quiescent Current IB − 3.6 6.0 mA Quiescent Current Change /C0068IB mA 27.3 Vdc ≤ Vin ≤ 38 Vdc, IO = 500 mA − − 0.8 27 Vdc ≤ Vin ≤ 38 Vdc, TJ = 25°C − − 0.8 Ripple Rejection RR 45 54 − dB

28 Vdc ≤ Vin ≤ 38 Vdc, f = 120 Hz, IO = 500 mA

Dropout Voltage (IO = 1.0 A, TJ = 25°C) VI − VO − 2.0 − Vdc Output Noise Voltage (TA = 25°C) Vn − 10 − /C0109V/VO Output Resistance (f = 1.0 kHz) rO − 1.4 − m/C0087 Short Circuit Current Limit (TA = 25°C) ISC − 0.2 − A Vin = 35 Vdc Peak Output Current (TJ = 25°C) Imax − 2.2 − A Average Temperature Coefficient of Output Voltage TCVO − −2.0 − mV/°C 31.Tlow =0 °C for MC78XXC, MC78XXAC, = /C004240°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB 32.Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used.

current as the voltage across the pass transistor is increased. Figure 9. Current Regulator Figure 10. Adjustable Output Regulator Figure 11. Current Boost Regulator Figure 12. Short Circuit Protection

10 W resistor and the output voltage compliance would be the input

B /C0094 3.2 mA over line and load changes. increased by VBE of the pass transistor. XX = 2 digits of type number indicating voltage. four-ampere plastic power transistor is specified. XX = 2 digits of type number indicating voltage.

MC7800, MC7800A, MC7800AE, NCV7800 http://onsemi.com DEFINITIONS Line Regulation − The change in output voltage for a change in the input voltage. The measurement is made under conditions of low dissipation or by using pulse techniques such that the average chip temperature is not significantly affected. Load Regulation − The change in output voltage for a change in load current at constant chip temperature. Maximum Power Dissipation − The maximum total device dissipation for which the regulator will operate within specifications. Quiescent Current − That part of the input current that is not delivered to the load. Output Noise Voltage − The rms ac voltage at the output, with constant load and no input ripple, measured over a specified frequency range. Long Term Stability − Output voltage stability under accelerated life test conditions with the maximum rated voltage listed in the devices’ electrical characteristics and maximum power dissipation. Temperature Range Package Shipping† MC7805ABD2T 5.0 V TJ = −40°C to +125°C D2PAK 50 Units /Rail MC7805ABD2TG D2PAK (Pb−free)

50 Units /Rail

MC7805ABD2TR4 D2PAK 800 / Tape & Reel MC7805ABD2TR4G D2PAK (Pb−free) 800 / Tape & Reel MC7805ABT TO−220 50 Units /Rail MC7805ABTG TO−220 (Pb−free) TJ = 0°C to +125°C D2PAK 50 Units /Rail MC7805ACD2TG D2PAK (Pb−free) MC7805ACD2TR4 D2PAK 800 / Tape & Reel MC7805ACD2TR4G D2PAK (Pb−free) 800 / Tape & Reel MC7805ACT TO−220 50 Units /Rail MC7805ACTG TO−220 (Pb−free) TJ = −40°C to +125°C D2PAK 50 Units /Rail MC7805BD2TG D2PAK (Pb−free) MC7805BD2TR4 D2PAK 800 / Tape & Reel MC7805BD2TR4G D2PAK (Pb−free) 800 / Tape & Reel MC7805BDT DPAK 75 Units / Rail MC7805BDTG DPAK (Pb−free)

75 Units / Rail

MC7805BDTRK DPAK 2500 / Tape & Reel MC7805BDTRKG DPAK (Pb−free) 2500 / Tape & Reel †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Spe- cifications Brochure, BRD8011/D. *NCV devices: Tlow = −40°C, Thigh = +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and change control.

MC7800, MC7800A, MC7800AE, NCV7800 http://onsemi.com Device Shipping†Package Operating Temperature RangeNominal Voltage MC7805BT 5.0 V TJ = −40°C to +125°C TO−220 50 Units /Rail MC7805BTG TO−220 (Pb−free) NCV7805BD2T* D2PAK 50 Units /Rail NCV7805BD2TG* D2PAK (Pb−free) NCV7805BD2TR4* D2PAK 800 / Tape & Reel NCV7805BD2TR4G* D2PAK (Pb−free) 800 / Tape & Reel NCV7805BT* TO−220 50 Units /Rail NCV7805BTG* TO−220 (Pb−free) TJ = 0°C to +125°C D2PAK 50 Units /Rail MC7805CD2TG D2PAK (Pb−free) MC7805CD2TR4 D2PAK 800 / Tape & Reel MC7805CD2TR4G D2PAK (Pb−free) 800 / Tape & Reel MC7805CDT DPAK 75 Units / Rail MC7805CDTG DPAK (Pb−free) MC7805CDTRK DPAK 2500 / Tape & Reel MC7805CDTRKG DPAK (Pb−free) 2500 / Tape & Reel MC7805CT TO−220 50 Units /Rail MC7805CTG TO−220 (Pb−free) NCV7805ABD2TR4G* 5.0 V TJ = −40°C to +125°C D2PAK (Pb−free) 800 / Tape & Reel MC7806ACT 6.0 V TJ = 0°C to +125°C TO−220 50 Units /Rail MC7806ACTG TO−220 (Pb−free) TJ = −40°C to +125°C D2PAK 50 Units /Rail MC7806BD2TG D2PAK (Pb−free) MC7806BD2TR4 D2PAK 800 / Tape & Reel MC7806BD2TR4G D2PAK (Pb−free) 800 / Tape & Reel MC7806BT TO−220 50 Units /Rail MC7806BTG TO−220 (Pb−free) TJ = 0°C to +125°C TO−220 50 Units /Rail MC7806CTG TO−220 (Pb−free) †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Spe- cifications Brochure, BRD8011/D. *NCV devices: Tlow = −40°C, Thigh = +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and change control.

MC7800, MC7800A, MC7800AE, NCV7800 http://onsemi.com Device Shipping†Package Operating Temperature RangeNominal Voltage MC7808ABD2T 8.0 V TJ = −40°C to +125°C D2PAK 50 Units / Rail MC7808ABD2TG D2PAK (Pb−free)

50 Units / Rail

MC7808ABD2TR4 D2PAK 800 / Tape & Reel MC7808ABD2TR4G D2PAK (Pb−free) 800 / Tape & Reel MC7808ABT TO−220 50 Units / Rail MC7808ABTG TO−220 (Pb−free) TJ = 0°C to +125°C TO−220 50 Units / Rail MC7808ACTG TO−220 (Pb−free) TJ = −40°C to +125°C TO−220 (Pb−free) 8.0 V D2PAK 50 Units / Rail MC7808BD2TG D2PAK (Pb−free) MC7808BD2TR4 D2PAK 800 / Tape & Reel MC7808BD2TR4G D2PAK (Pb−free) 800 / Tape & Reel MC7808BDT DPAK 75 Units / Rail MC7808BDTG DPAK (Pb−free) MC7808BDTRK DPAK 2500 / Tape & Reel MC7808BDTRKG DPAK (Pb−free) 2500 / Tape & Reel MC7808BT TO−220 50 Units /Rail MC7808BTG TO−220 (Pb−free)

8.0 V TJ = 0°C to +125°C

(Pb−free) MC7808CD2TR4 D2PAK 800 / Tape & Reel MC7808CD2TR4G D2PAK (Pb−free) 800 / Tape & Reel MC7808CDT DPAK 75 Units / Rail MC7808CDTG DPAK (Pb−free) MC7808CDTRK DPAK 2500 / Tape & Reel MC7808CDTRKG DPAK (Pb−free) 2500 / Tape & Reel MC7808CT TO−220 50 Units /Rail MC7808CTG TO−220 (Pb−free) †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Spe- cifications Brochure, BRD8011/D. *NCV devices: Tlow = −40°C, Thigh = +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and change control.

MC7800, MC7800A, MC7800AE, NCV7800 http://onsemi.com Device Shipping†Package Operating Temperature RangeNominal Voltage NCV7808BDTG* 8.0 V TJ = −40°C to +125°C DPAK (Pb−free) NCV7808BTG* TO−220 (Pb−free) 9.0 V TJ = −40°C to +125°C TO−220 (Pb−free) TJ = 0°C to +125°C TO−220 50 Units /Rail MC7809ACTG TO−220 (Pb−free) TJ = −40°C to +125°C TO−220 50 Units /Rail MC7809BTG TO−220 (Pb−free) TJ = 0°C to +125°C D2PAK 50 Units /Rail MC7809CD2TG D2PAK (Pb−free) MC7809CD2TR4 D2PAK 800 / Tape & Reel MC7809CD2TR4G D2PAK (Pb−free) 800 / Tape & Reel MC7809CT TO−220 50 Units /Rail MC7809CTG TO−220 (Pb−free)

12 V TJ = −40°C to +125°C

(Pb−free) MC7812ABD2TR4 D2PAK 800 / Tape & Reel MC7812ABD2TR4G D2PAK (Pb−free) 800 / Tape & Reel MC7812ABT TO−220 50 Units /Rail MC7812ABTG TO−220 (Pb−free)

12 V TJ = 0°C to +125°C

(Pb−free) MC7812ACD2TR4 D2PAK 800 / Tape & Reel MC7812ACD2TR4G D2PAK (Pb−free) 800 / Tape & Reel MC7812ACT TO−220 50 Units /Rail MC7812ACTG TO−220 (Pb−free) †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Spe- cifications Brochure, BRD8011/D. *NCV devices: Tlow = −40°C, Thigh = +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and change control.

MC7800, MC7800A, MC7800AE, NCV7800 http://onsemi.com Device Shipping†Package Operating Temperature RangeNominal Voltage MC7812BD2T (Pb−free) MC7812BD2TR4 D2PAK 800 / Tape & Reel MC7812BD2TR4G D2PAK (Pb−free) 800 / Tape & Reel MC7812BDT DPAK 75 Units / Rail MC7812BDTG DPAK (Pb−free) DPAK 2500 / Tape & Reel MC7812BDTRKG DPAK (Pb−free) 2500 / Tape & Reel MC7812BT TO−220 50 Units / Rail MC7812BTG TO−220 (Pb−free) NCV7812BD2T* NCV7812BD2TR4* D2PAK 800 / Tape & Reel NCV7812BD2TR4G* D2PAK (Pb−free) 800 / Tape & Reel NCV7812BT* TO−220 50 Units /Rail NCV7812BTG* TO−220 (Pb−free) (Pb−free) MC7812CD2TR4 D2PAK 800 / Tape & Reel MC7812CD2TR4G D2PAK (Pb−free) 800 / Tape & Reel MC7812CDT DPAK 75 Units / Rail MC7812CDTG DPAK (Pb−free) MC7812CDTRK DPAK 2500 / Tape & Reel MC7812CDTRKG DPAK (Pb−free) 2500 / Tape & Reel MC7812CT TO−220 50 Units /Rail MC7812CTG TO−220 (Pb−free) NCV7812ABTG* 12 V TJ = −40°C to +125°C TO−220 (Pb−free) †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Spe- cifications Brochure, BRD8011/D. *NCV devices: Tlow = −40°C, Thigh = +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and change control.

MC7800, MC7800A, MC7800AE, NCV7800 http://onsemi.com Device Shipping†Package Operating Temperature RangeNominal Voltage MC7815ABD2T 15 V TJ = −40°C to +125°C D2PAK 50 Units /Rail MC7815ABD2TG D2PAK (Pb−free) MC7815ABD2TR4 D2PAK 800 / Tape & Reel MC7815ABD2TR4G D2PAK (Pb−free) 800 / Tape & Reel MC7815ABT TO−220 50 Units /Rail MC7815ABTG TO−220 (Pb−free) TJ = 0°C to +125°C D2PAK 50 Units /Rail MC7815ACD2TG D2PAK (Pb−free) MC7815ACT TO−220 50 Units /Rail MC7815ACTG TO−220 (Pb−free) TJ = −40°C to +125°C D2PAK 50 Units /Rail MC7815BD2TG D2PAK (Pb−free) NCV7815BTG*

15 V TJ = −40°C to +125°C

TO−220 (Pb−free) MC7815BD2TR4 D2PAK 800 / Tape & Reel MC7815BD2TR4G D2PAK (Pb−free) 800 / Tape & Reel MC7815BDT DPAK 75 Units / Rail MC7815BDTG DPAK (Pb−free) MC7815BDTRK DPAK 2500 / Tape & Reel MC7815BDTRKG DPAK (Pb−free) 2500 / Tape & Reel MC7815BT TO−220 50 Units / Rail MC7815BTG TO−220 (Pb−free) †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Spe- cifications Brochure, BRD8011/D. *NCV devices: Tlow = −40°C, Thigh = +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and change control.

MC7800, MC7800A, MC7800AE, NCV7800 http://onsemi.com Device Shipping†Package Operating Temperature RangeNominal Voltage MC7815CD2T

15 V TJ = 0°C to +125°C

(Pb−free) MC7815CD2TR4 D2PAK 800 / Tape & Reel MC7815CD2TR4G D2PAK (Pb−free) 800 / Tape & Reel MC7815CDT DPAK 75 Units / Rail MC7815CDTG DPAK (Pb−free) MC7815CDTRK DPAK 2500 / Tape & Reel MC7815CDTRKG DPAK (Pb−free) 2500 / Tape & Reel MC7815CT TO−220 50 Units /Rail MC7815CTG TO−220 (Pb−free) TJ = 0°C to +125°C TO−220 50 Units /Rail MC7818ACTG TO−220 (Pb−free) TJ = −40°C to +125°C TO−220 50 Units /Rail MC7818BTG TO−220 (Pb−free) TJ = 0°C to +125°C D2PAK 50 Units /Rail MC7818CD2TR4 D2PAK 800 / Tape & Reel MC7818CD2TR4G D2PAK (Pb−free) 800 / Tape & Reel MC7818CT TO−220 50 Units /Rail MC7818CTG TO−220 (Pb−free) †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Spe- cifications Brochure, BRD8011/D. *NCV devices: Tlow = −40°C, Thigh = +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and change control.

MC7800, MC7800A, MC7800AE, NCV7800 http://onsemi.com Device Shipping†Package Operating Temperature RangeNominal Voltage MC7824ACT 24 V TJ = 0°C to +125°C TO−220 50 Units /Rail MC7824ACTG TO−220 (Pb−free) TJ = −40°C to +125°C D2PAK 50 Units /Rail MC7824BD2TG D2PAK (Pb−free) MC7824BD2TR4 D2PAK 800 / Tape & Reel MC7824BD2TR4G D2PAK (Pb−free) 800 / Tape & Reel MC7824BT TO−220 50 Units /Rail MC7824BTG TO−220 (Pb−free) TJ = 0°C to +125°C D2PAK 50 Units /Rail MC7824CD2TG D2PAK (Pb−free) MC7824CD2TR4 D2PAK 800 / Tape & Reel MC7824CD2TR4G D2PAK (Pb−free) 800 / Tape & Reel MC7824CT TO−220 50 Units /Rail MC7824CTG TO−220 (Pb−free) †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Spe- cifications Brochure, BRD8011/D. *NCV devices: Tlow = −40°C, Thigh = +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and change control. 78xxAyD2T AWLYWWG MC 78xxAyT AWLYWWG xx = 05, 06, 08, 09, 12, 15, 18, or 24 y = B or C A = Assembly Location WL, L = Wafer Lot Y = Year WW = Work Week G = Pb −Free Device MARKING DIAGRAMS TO−220−3 T SUFFIX CASE 221A MC D2PAK−3 D2T SUFFIX CASE 936 DPAK−3 DT SUFFIX CASE 369C 78xxyG ALYWW78xxyD2T AWLYWWG MC * MC 78xxyT AWLYWWG *This marking diagram also applies to NCV78xx family. MC 78xxAEyT AWLYWWG

MC7800, MC7800A, MC7800AE, NCV7800 http://onsemi.com PACKAGE DIMENSIONS TO−220, SINGLE GAUGE T SUFFIX CASE 221AB−01 ISSUE O NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION Z DEFINES A ZONE WHERE ALL BODY AND LEAD IRREGULARITIES ARE ALLOWED. DIM MIN MAX MIN MAX MILLIMETERSINCHES A 0.570 0.620 14.48 15.75 B 0.380 0.405 9.66 10.28 C 0.160 0.190 4.07 4.82 D 0.025 0.035 0.64 0.88 F 0.142 0.147 3.61 3.73 G 0.095 0.105 2.42 2.66 H 0.110 0.155 2.80 3.93 J 0.018 0.025 0.46 0.64 K 0.500 0.562 12.70 14.27 L 0.045 0.060 1.15 1.52 N 0.190 0.210 4.83 5.33 Q 0.100 0.120 2.54 3.04 R 0.080 0.110 2.04 2.79 S 0.020 0.055 0.508 1.39 T 0.235 0.255 5.97 6.47 U 0.000 0.050 0.00 1.27 B Q H Z L V G N A K F 12 3 D SEATING PLANE−T− C ST U R J

MC7800, MC7800A, MC7800AE, NCV7800 http://onsemi.com PACKAGE DIMENSIONS D2PAK−3 D2T SUFFIX CASE 936−03 ISSUE C

5 REF5 REF

V U TERMINAL 4 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. TAB CONTOUR OPTIONAL WITHIN DIMENSIONS A AND K. 4. DIMENSIONS U AND V ESTABLISH A MINIMUM MOUNTING SURFACE FOR TERMINAL 4. 5. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH OR GATE PROTRUSIONS. MOLD FLASH AND GATE PROTRUSIONS NOT TO EXCEED 0.025 (0.635) MAXIMUM. DIM A MIN MAX MIN MAX MILLIMETERS 0.386 0.403 9.804 10.236 INCHES B 0.356 0.368 9.042 9.347 C 0.170 0.180 4.318 4.572 D 0.026 0.036 0.660 0.914 E 0.045 0.055 1.143 1.397 F 0.051 REF 1.295 REF G 0.100 BSC 2.540 BSC H 0.539 0.579 13.691 14.707 J 0.125 MAX 3.175 MAX K 0.050 REF 1.270 REF L 0.000 0.010 0.000 0.254 M 0.088 0.102 2.235 2.591 N 0.018 0.026 0.457 0.660 P 0.058 0.078 1.473 1.981 R S 0.116 REF 2.946 REF U 0.200 MIN 5.080 MIN V 0.250 MIN 6.350 MIN /C0095/C0095 A 12 3 K F B J S H D G C M0.010 (0.254) T E M L PN R −T− OPTIONAL CHAMFER *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. SOLDERING FOOTPRINT* 8.38 5.080 DIMENSIONS: MILLIMETERS PITCH 16.155 1.016 10.49 3.504

MC7800, MC7800A, MC7800AE, NCV7800 http://onsemi.com PACKAGE DIMENSIONS DPAK−3 DT SUFFIX CASE 369C−01 ISSUE D b D E e M0.005 (0.13) C A c C Z DIM MIN MAX MIN MAX MILLIMETERSINCHES D 0.235 0.245 5.97 6.22 E 0.250 0.265 6.35 6.73 A 0.086 0.094 2.18 2.38 b 0.025 0.035 0.63 0.89 c2 0.018 0.024 0.46 0.61 b2 0.030 0.045 0.76 1.14 c 0.018 0.024 0.46 0.61 e 0.090 BSC 2.29 BSC b3 0.180 0.215 4.57 5.46 L 0.055 0.070 1.40 1.78 L3 0.035 0.050 0.89 1.27 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: INCHES. 3. THERMAL PAD CONTOUR OPTIONAL WITHIN DIMENSIONS b3, L3 and Z. 4. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR BURRS. MOLD FLASH, PROTRUSIONS, OR GATE BURRS SHALL NOT EXCEED 0.006 INCHES PER SIDE. 5. DIMENSIONS D AND E ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY . 6. DATUMS A AND B ARE DETERMINED AT DATUM PLANE H.12 3 5.80 0.228 2.58 0.102 1.60 0.063 6.20 0.244 3.00 0.118 6.17 0.243 /C0466mm inches/C0467SCALE 3:1 *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. SOLDERING FOOTPRINT* H 0.370 0.410 9.40 10.41 A1 0.000 0.005 0.00 0.13 L1 0.108 REF 2.74 REF L2 0.020 BSC 0.51 BSC HDETAIL A SEATING PLANE A B C L H L2 GAUGE PLANE DETAIL A ROTATED 90 CW/C0053 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, direct ly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. MC7800/D PUBLICATION ORDERING INFORMATION N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5773−3850 LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: orderlit@onsemi.com ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative