Power Management

MC7805B

ON Semiconductor

Voltage Regulators - Positive 1.0 A November, 2021 - Rev. 29

Manufacturer: ON Semiconductor

Document: 28 Pages / 439Kb

Request Quote Download Datasheet Read online HTML view

More from ON Semiconductor Browse M parts

Online Datasheet

Read MC7805B online.

MC7800_V01 ONSEMI | Alldatasheet

Document overview

Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
PDF pages: 28

Technical content

Features

Output Current in Excess of 1.0 A
No External Components Required
Internal Thermal Overload Protection
Internal Short Circuit Current Limiting
Output Transistor SafeïArea Compensation
Output V oltage Offered in 1.5%, 2% and 4% Tolerance
Available in Surface Mount D2PAKï3, DPAKï3 and Standard 3ïLead Transistor Packages
NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AECïQ100 Qualified and PPAP Capable
These are PbïFree Devices MAXIMUM RATINGS (TA = 25°C, unless otherwise noted) Rating Symbol Value Unit 369C 221A 936 Input Voltage (5.0 ï 18 V) (24 V) VI 35 Vdc Power Dissipation PD Internally Limited W Thermal Resistance, JunctionïtoïAmbient R/C0113JA 92 65 Figure °C/W Thermal Resistance, JunctionïtoïCase R/C0113JC 5.0 5.0 5.0 °C/W Storage Junction Temperature Range Tstg ï65 to +150 °C Operating Junction Temperature TJ +150 °C Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. *This device series contains ESD protection and exceeds the following tests: Human Body Model 2000 V per MIL_STD_883, Method 3015. Machine Model Method 200 V. TOï220 T SUFFIX CASE 221AB D2PAKï3 D2T SUFFIX CASE 936 See detailed ordering and shipping information in the package dimensions section on page 21 of this data sheet.

ORDERING INFORMATION

connected to Pin 2. Pin 1. Input 2. Ground 3. Output Heatsink surface (shown as terminal 4 in case outline drawing) is connected to Pin 2. STANDARD APPLICATION A common ground is required between the input and the output voltages. The input voltage must remain typically 2.0 V above the output voltage even during the low point on the input ripple voltage. XX, MC78XXInput Cin* 0.33 /C0109F CO** Output These two digits of the type number indicate nominal voltage. Cin is required if regulator is located an appreciable distance from power supply filter. CO is not needed for stability; however, it does improve transient response. Values of less than 0.1 /C0109F could cause instability. See general marking information in the device marking section on page 24 of this data sheet. DEVICE MARKING INFORMATION DPAKï3 DT SUFFIX CASE 369C 1 2

30 PC2

Figure 1. Representative Schematic Diagram This device contains 22 active transistors.

MC7800, MC7800A, MC7800AE, NCV7800 www.onsemi.com ELECTRICAL CHARACTERISTICS (Vin = 10 V, IO = 500 mA, TJ = Tlow to 125°C (Note 1), unless otherwise noted) Characteristic Symbol MC7805B, NCV7805B MC7805C UnitMin Typ Max Min Typ Max Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤ 15 W)

7.0 Vdc ≤ Vin ≤ 20 Vdc

8.0 Vdc ≤ Vin ≤ 20 Vdc

ï 4.75 ï 5.0 ï 5.25 4.75 ï 5.0 ï 5.25 ï Vdc Line Regulation (Note 4) 7.5 Vdc ≤ Vin ≤ 20 Vdc, 1.0 A

8.0 Vdc ≤ Vin ≤ 12 Vdc

ï ï 5.0 1.3 100 ï ï 0.5 0.8 mV Load Regulation (Note 4) 5.0 mA ≤ IO ≤ 1.0 A 5.0 mA ≤ IO ≤ 1.5 A (TA = 25°C) Regload ï ï 1.3 0.15 100 ï ï 1.3 1.3 mV Quiescent Current IB ï 3.2 8.0 ï 3.2 6.5 mA Quiescent Current Change

7.0 Vdc ≤ Vin ≤ 25 Vdc

5.0 mA ≤ IO ≤ 1.0 A (TA = 25°C) /C0068IB ï ï ï ï ï 0.5 ï ï 0.3 0.08 1.0 0.8 mA Ripple Rejection

8.0 Vdc ≤ Vin ≤ 18 Vdc, f = 120 Hz

ï 68 ï 62 83 ï dB Dropout Voltage (IO = 1.0 A, TJ = 25°C) VI ï VO ï 2.0 ï ï 2.0 ï Vdc Output Noise Voltage (TA = 25°C)

10 Hz ≤ f ≤ 100 kHz

ï 10 ï ï 10 ï /C0109V/VO Output Resistance f = 1.0 kHz rO ï 0.9 ï ï 0.9 ï m/C0087 Short Circuit Current Limit (TA = 25°C) Vin = 35 Vdc ISC ï 0.2 ï ï 0.6 ï A Peak Output Current (TJ = 25°C) Imax ï 2.2 ï ï 2.2 ï A Average Temperature Coefficient of Output Voltage TCVO ï ï0.3 ï ï ï0.3 ï mV/°C 1. T low = 0°C for MC78XXC, MC78XXAC, = /C004240°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB 2. Load and line regulation are specified at constan t junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used.

MC7800, MC7800A, MC7800AE, NCV7800 www.onsemi.com ELECTRICAL CHARACTERISTICS (Vin = 10 V, IO = 1.0 A, TJ = Tlow to 125°C (Note 3), unless otherwise noted) MC7805AB/MC7805AC/NCV7805AB Characteristic Symbol Min Typ Max Unit Output Voltage (TJ = 25°C) VO 4.9 5.0 5.1 Vdc Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤ 15 W)

7.5 Vdc ≤ Vin ≤ 20 Vdc

4.8 5.0 5.2 Vdc Line Regulation (Note 4)

7.5 Vdc ≤ Vin ≤ 25 Vdc, IO = 500 mA

8.0 Vdc ≤ Vin ≤ 12 Vdc, IO = 1.0 A 8.0 Vdc ≤ Vin ≤ 12 Vdc, IO = 1.0 A, TJ = 25°C 7.3 Vdc ≤ Vin ≤ 20 Vdc, IO = 1.0 A, TJ = 25°C Regline ï ï ï ï 0.5 0.8 1.3 4.5 4.0 mV Load Regulation (Note 4) 5.0 mA ≤ IO ≤ 1.5 A, TJ = 25°C 5.0 mA ≤ IO ≤ 1.0 A 250 mA ≤ IO ≤ 750 mA Regload ï ï ï 1.3 0.8 0.53 mV Quiescent Current IB ï 3.2 6.0 mA Quiescent Current Change

8.0 Vdc ≤ Vin ≤ 25 Vdc, IO = 500 mA

7.5 Vdc ≤ Vin ≤ 20 Vdc, TJ = 25°C

5.0 mA ≤ IO ≤ 1.0 A /C0068IB ï ï ï 0.3 ï 0.08 0.8 0.8 0.5 mA Ripple Rejection

8.0 Vdc ≤ Vin ≤ 18 Vdc, f = 120 Hz, IO = 500 mA

68 83 ï dB Dropout Voltage (IO = 1.0 A, TJ = 25°C) VI ï VO ï 2.0 ï Vdc Output Noise Voltage (TA = 25°C) ï 10 ï /C0109V/VO Output Resistance (f = 1.0 kHz) rO ï 0.9 ï m/C0087 Short Circuit Current Limit (TA = 25°C) Vin = 35 Vdc ISC ï 0.2 ï A Peak Output Current (TJ = 25°C) Imax ï 2.2 ï A Average Temperature Coefficient of Output Voltage TCVO ï ï0.3 ï mV/°C 3. T low = 0°C for MC78XXC, MC78XXAC, = /C004240°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB 4. Load and line regulation are specified at constan t junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used.

MC7800, MC7800A, MC7800AE, NCV7800 www.onsemi.com ELECTRICAL CHARACTERISTICS (Vin = 14 V, IO = 500 mA, TJ = Tlow to 125°C (Note 5), unless otherwise noted) MC7808B/NCV7808B MC7808C Characteristic Symbol Min Typ Max Min Typ Max Unit Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤ 15 W)

10.5 Vdc ≤ Vin ≤ 23 Vdc

11.5 Vdc ≤ Vin ≤ 23 Vdc

ï 7.6 ï 8.0 ï 8.4 7.6 ï 8.0 ï 8.4 ï Vdc Line Regulation, TJ = 25°C, (Note 6)

10.5 Vdc ≤ Vin ≤ 25 Vdc

11 Vdc ≤ Vin ≤ 17 Vdc

ï ï 6.0 1.7 160 ï ï 6.0 1.7 mV Load Regulation, TJ = 25°C (Note 6) 5.0 mA ≤ IO ≤ 1.5 A Regload ï 1.4 160 ï 1.4 35 mV Quiescent Current IB ï 3.3 8.0 ï 3.3 8.0 mA Quiescent Current Change 5.0 mA ≤ IO ≤ 1.0 A /C0068IB ï ï ï ï ï 0.5 ï ï ï ï 1.0 0.5 mA Ripple Rejection

11.5 Vdc ≤ Vin ≤ 18 Vdc, f = 120 Hz

ï 62 ï 56 62 ï dB Dropout Voltage (IO = 1.0 A, TJ = 25°C) VI ï VO ï 2.0 ï ï 2.0 ï Vdc Output Noise Voltage (TA = 25°C) ï 10 ï ï 10 ï /C0109V/VO Output Resistance f = 1.0 kHz rO ï 0.9 ï ï 0.9 ï m/C0087 Short Circuit Current Limit (TA = 25°C) Vin = 35 Vdc ISC ï 0.2 ï ï 0.2 ï A Peak Output Current (TJ = 25°C) Imax ï 2.2 ï ï 2.2 ï A Average Temperature Coefficient of Output Voltage TCVO ï ï0.4 ï ï ï0.4 ï mV/°C 5. T low = 0°C for MC78XXC, MC78XXAC, = /C004240°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB 6. Load and line regulation are specified at constan t junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used.

MC7800, MC7800A, MC7800AE, NCV7800 www.onsemi.com ELECTRICAL CHARACTERISTICS (Vin = 14 V, IO = 1.0 A, TJ = Tlow to 125°C (Note 7), unless otherwise noted) Characteristic Symbol MC7808AB/MC7808AC/NCV7808AB UnitMin Typ Max Output Voltage (TJ = 25°C) VO 7.84 8.0 8.16 Vdc Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤ 15 W)

10.6 Vdc ≤ Vin ≤ 23 Vdc

7.7 8.0 8.3 Vdc Line Regulation (Note 8)

10.6 Vdc ≤ Vin ≤ 25 Vdc, IO = 500 mA

11 Vdc ≤ Vin ≤ 17 Vdc, IO = 1.0 A

10.4 Vdc ≤ Vin ≤ 23 Vdc, TJ = 25°C

ï ï ï 6.0 1.7 5.0 mV Load Regulation (Note 8) 5.0 mA ≤ IO ≤ 1.5 A, TJ = 25°C 5.0 mA ≤ IO ≤ 1.0 A 250 mA ≤ IO ≤ 750 mA Regload ï ï ï 1.4 1.0 0.22 mV Quiescent Current IB ï 3.3 6.0 mA Quiescent Current Change

11 Vdc ≤ Vin ≤ 25 Vdc, IO = 500 mA

10.6 Vdc ≤ Vin ≤ 23 Vdc, IO = 1.0 A, TJ = 25°C 5.0 mA ≤ IO ≤ 1.0 A /C0068IB ï ï ï ï ï ï 0.8 0.8 0.5 mA Ripple Rejection 11.5 Vdc ≤ Vin ≤ 21.5 Vdc, f = 120 Hz, IO = 500 mA RR 56 62 ï dB Dropout Voltage (IO = 1.0 A, TJ = 25°C) VI ï VO ï 2.0 ï Vdc Output Noise Voltage (TA = 25°C) ï 10 ï /C0109V/VO Output Resistance f = 1.0 kHz rO ï 0.9 ï m/C0087 Short Circuit Current Limit (TA = 25°C) Vin = 35 Vdc ISC ï 0.2 ï A Peak Output Current (TJ = 25°C) Imax ï 2.2 ï A Average Temperature Coefficient of Output Voltage TCVO ï ï0.4 ï mV/°C 7. T low = 0°C for MC78XXC, MC78XXAC, = /C004240°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB 8. Load and line regulation are specified at constan t junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used.

MC7800, MC7800A, MC7800AE, NCV7800 www.onsemi.com ELECTRICAL CHARACTERISTICS (Vin = 15 V, IO = 500 mA, TJ = Tlow to 125°C (Note 9), unless otherwise noted) MC7809B/NCV7809B MC7809C Characteristic Symbol Min Typ Max Min Typ Max Unit Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤ 15 W)

11.5 Vdc ≤ Vin ≤ 24 Vdc

Line Regulation, TJ = 25°C (Note 10)

11 Vdc ≤ Vin ≤ 26 Vdc

11.5 Vdc ≤ Vin ≤ 17 Vdc

ï ï 6.2 1.8 ï ï 6.2 1.8 mV Load Regulation, TJ = 25°C (Note 10) 5.0 mA ≤ IO ≤ 1.5 A Regload ï 1.5 35 ï 1.5 35 mV Quiescent Current IB ï 3.4 8.0 ï 3.4 8.0 mA Quiescent Current Change

11.5 Vdc ≤ Vin ≤ 26 Vdc

5.0 mA ≤ IO ≤ 1.0 A /C0068IB ï ï ï ï 1.0 0.5 ï ï ï ï 1.0 0.5 mA Ripple Rejection 11.5 Vdc ≤ Vin ≤ 21.5 Vdc, f = 120 Hz RR 56 61 ï 56 61 ï dB Dropout Voltage (IO = 1.0 A, TJ = 25°C) VI ï VO ï 2.0 ï ï 2.0 ï Vdc Output Noise Voltage (TA = 25°C) ï 10 ï ï 10 ï /C0109V/VO Output Resistance f = 1.0 kHz rO ï 1.0 ï ï 1.0 ï m/C0087 Short Circuit Current Limit (TA = 25°C) Vin = 35 Vdc ISC ï 0.2 ï ï 0.2 ï A Peak Output Current (TJ = 25°C) Imax ï 2.2 ï ï 2.2 ï A Average Temperature Coefficient of Output Voltage TCVO ï ï0.5 ï ï ï0.5 ï mV/°C 9. T low = 0°C for MC78XXC, MC78XXAC, = /C004240°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB 10.Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used.

MC7800, MC7800A, MC7800AE, NCV7800 www.onsemi.com ELECTRICAL CHARACTERISTICS (Vin = 15 V, IO = 1.0 A, TJ = Tlow to 125°C (Note 11), unless otherwise noted) Characteristic Symbol MC7809AB/MC7809AC UnitMin Typ Max Output Voltage (TJ = 25°C) VO 8.82 9.0 9.18 Vdc Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤ 15 W) 8.65 9.0 9.35 Vdc Line Regulation (Note 12)

11.5 Vdc ≤ Vin ≤ 26 Vdc, IO = 500 mA

12 Vdc ≤ Vin ≤ 17 Vdc, IO = 1.0 A

11.5 Vdc ≤ Vin ≤ 24 Vdc, TJ = 25°C

ï ï ï 6.2 1.8 5.2 7.0 mV Load Regulation (Note 12) 5.0 mA ≤ IO ≤ 1.5 A, TJ = 25°C 5.0 mA ≤ IO ≤ 1.0 A 250 mA ≤ IO ≤ 750 mA Regload ï ï ï ï ï ï mV Quiescent Current IB ï 3.3 6.0 mA Quiescent Current Change 11.5 Vdc ≤ Vin ≤ 24 Vdc, IO = 1.0 A, TJ = 25°C 5.0 mA ≤ IO ≤ 1.0 A /C0068IB ï ï ï ï ï ï 0.8 0.8 0.5 mA Ripple Rejection 11.5 Vdc ≤ Vin ≤ 21.5 Vdc, f = 120 Hz, IO = 500 mA RR 56 61 ï dB Dropout Voltage (IO = 1.0 A, TJ = 25°C) VI _ VO 2.0 Vdc Output Noise Voltage (TA = 25°C) ï 10 ï /C0109V/VO Output Resistance f = 1.0 kHz rO ï 1.0 ï m/C0087 Short Circuit Current Limit (TA = 25°C) Vin = 35 Vdc ISC ï 0.2 ï A Peak Output Current (TJ = 25°C) Imax ï 2.2 ï A Average Temperature Coefficient of Output Voltage TCVO ï ï0.5 ï mV/°C 11. Tlow = 0°C for MC78XXC, MC78XXAC, = /C004240°C for NCV78XX, MC78XXB, MC78XXAB. 12.Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used.

MC7800, MC7800A, MC7800AE, NCV7800 www.onsemi.com ELECTRICAL CHARACTERISTICS (Vin = 19 V, IO = 500 mA, TJ = Tlow to 125°C (Note 13), unless otherwise noted) MC7812B/NCV7812B MC7812C Characteristic Symbol Min Typ Max Min Typ Max Unit Output Voltage (TJ = 25°C) VO 11.5 12 12.5 11.5 12 12.5 Vdc Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤ 15 W)

14.5 Vdc ≤ Vin ≤ 27 Vdc

15.5 Vdc ≤ Vin ≤ 27 Vdc

ï 11.4 ï ï 12.6 11.4 ï ï 12.6 ï Vdc Line Regulation, TJ = 25°C (Note 14)

14.5 Vdc ≤ Vin ≤ 30 Vdc

16 Vdc ≤ Vin ≤ 22 Vdc

14.8 Vdc ≤ Vin ≤ 27 Vdc, IO = 1.0 A Regline ï ï ï 7.5 2.2 ï 240 120 ï ï ï ï 3.8 0.3 ï mV Load Regulation, TJ = 25°C (Note 14) 5.0 mA ≤ IO ≤ 1.5 A Regload ï 1.6 240 ï 8.1 60 mV Quiescent Current IB ï 3.4 8.0 ï 3.4 6.5 mA Quiescent Current Change 14.5 Vdc ≤ Vin ≤ 30 Vdc, IO = 1.0 A, TJ = 25°C

15 Vdc ≤ Vin ≤ 30 Vdc

5.0 mA ≤ IO ≤ 1.0 A /C0068IB ï ï ï ï ï ï ï 1.0 0.5 ï ï ï ï ï ï 0.7 0.8 0.5 mA Ripple Rejection

15 Vdc ≤ Vin ≤ 25 Vdc, f = 120 Hz

ï 60 ï 55 60 ï dB Dropout Voltage (IO = 1.0 A, TJ = 25°C) VI ï VO ï 2.0 ï ï 2.0 ï Vdc Output Noise Voltage (TA = 25°C) ï 10 ï ï 10 ï /C0109V/VO Output Resistance f = 1.0 kHz rO ï 1.1 ï ï 1.1 ï m/C0087 Short Circuit Current Limit (TA = 25°C) Vin = 35 Vdc ISC ï 0.2 ï ï 0.2 ï A Peak Output Current (TJ = 25°C) Imax ï 2.2 ï ï 2.2 ï A Average Temperature Coefficient of Output Voltage TCVO ï ï0.8 ï ï ï0.8 ï mV/°C 13.Tlow = 0°C for MC78XXC, MC78XXAC, = /C004240°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB 14.Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used.

MC7800, MC7800A, MC7800AE, NCV7800 www.onsemi.com ELECTRICAL CHARACTERISTICS (Vin = 19 V, IO = 1.0 A, TJ = Tlow to 125°C (Note 15), unless otherwise noted) MC7812AB/MC7812AC/NCV7812AB Characteristic Symbol Min Typ Max Unit Output Voltage (TJ = 25°C) VO 11.75 12 12.25 Vdc Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤ 15 W)

14.8 Vdc ≤ Vin ≤ 27 Vdc

11.5 12 12.5 Vdc Line Regulation (Note 16)

14.8 Vdc ≤ Vin ≤ 30 Vdc, IO = 500 mA

16 Vdc ≤ Vin ≤ 22 Vdc, IO = 1.0 A

14.5 Vdc ≤ Vin ≤ 27 Vdc, TJ = 25°C

ï ï ï 3.8 2.2 6.0 120 mV Load Regulation (Note 16) 5.0 mA ≤ IO ≤ 1.5 A, TJ = 25°C 5.0 mA ≤ IO ≤ 1.0 A Regload ï ï ï ï mV Quiescent Current IB ï 3.4 6.0 mA Quiescent Current Change

15 Vdc ≤ Vin ≤ 30 Vdc, IO = 500 mA

14.8 Vdc ≤ Vin ≤ 27 Vdc, TJ = 25°C

5.0 mA ≤ IO ≤ 1.0 A, TJ = 25°C /C0068IB ï ï ï ï ï ï 0.8 0.8 0.5 mA Ripple Rejection

15 Vdc ≤ Vin ≤ 25 Vdc, f = 120 Hz, IO = 500 mA

55 60 ï dB Dropout Voltage (IO = 1.0 A, TJ = 25°C) VI ï VO ï 2.0 ï Vdc Output Noise Voltage (TA = 25°C) ï 10 ï /C0109V/VO Output Resistance (f = 1.0 kHz) rO ï 1.1 ï m/C0087 Short Circuit Current Limit (TA = 25°C) Vin = 35 Vdc ISC ï 0.2 ï A Peak Output Current (TJ = 25°C) Imax ï 2.2 ï A Average Temperature Coefficient of Output Voltage TCVO ï ï0.8 ï mV/°C 15.Tlow = 0°C for MC78XXC, MC78XXAC, = /C004240°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB 16.Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used.

MC7800, MC7800A, MC7800AE, NCV7800 www.onsemi.com ELECTRICAL CHARACTERISTICS (Vin = 23 V, IO = 500 mA, TJ = Tlow to 125°C (Note 17), unless otherwise noted) MC7815B/NCV7815B MC7815C Characteristic Symbol Min Typ Max Min Typ Max Unit Output Voltage (TJ = 25°C) VO 14.4 15 15.6 14.4 15 15.6 Vdc Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤ 15 W)

17.5 Vdc ≤ Vin ≤ 30 Vdc

18.5 Vdc ≤ Vin ≤ 30 Vdc

ï 14.25 ï ï 15.75 14.25 ï ï 15.75 ï Vdc Line Regulation, TJ = 25°C (Note 18)

17.9 Vdc ≤ Vin ≤ 30 Vdc

20 Vdc ≤ Vin ≤ 26 Vdc

ï ï 8.5 3.0 300 150 ï ï 8.5 3.0 mV Load Regulation, TJ = 25°C (Note 18) 5.0 mA ≤ IO ≤ 1.5 A Regload ï 1.8 300 ï 1.8 55 mV Quiescent Current IB ï 3.5 8.0 ï 3.5 6.5 mA Quiescent Current Change 17.5 Vdc ≤ Vin ≤ 30 Vdc, IO = 1.0 A, TJ = 25°C 5.0 mA ≤ IO ≤ 1.0 A /C0068IB ï ï ï ï ï ï ï 1.0 0.5 ï ï ï ï ï ï 0.8 0.7 0.5 mA Ripple Rejection 18.5 Vdc ≤ Vin ≤ 28.5 Vdc, f = 120 Hz RR ï 58 ï 54 58 ï dB Dropout Voltage (IO = 1.0 A, TJ = 25°C) VI ï VO ï 2.0 ï ï 2.0 ï Vdc Output Noise Voltage (TA = 25°C) ï 10 ï ï 10 ï /C0109V/VO Output Resistance f = 1.0 kHz rO ï 1.2 ï ï 1.2 ï m/C0087 Short Circuit Current Limit (TA = 25°C) Vin = 35 Vdc ISC ï 0.2 ï ï 0.2 ï A Peak Output Current (TJ = 25°C) Imax ï 2.2 ï ï 2.2 ï A Average Temperature Coefficient of Output Voltage TCVO ï ï1.0 ï ï ï1.0 ï mV/°C 17.Tlow = 0°C for MC78XXC, MC78XXAC, = /C004240°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB 18.Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used.

MC7800, MC7800A, MC7800AE, NCV7800 www.onsemi.com ELECTRICAL CHARACTERISTICS (Vin = 23 V, IO = 1.0 A, TJ = Tlow to 125°C (Note 19), unless otherwise noted) MC7815AB/MC7815AC Characteristic Symbol Min Typ Max Unit Output Voltage (TJ = 25°C) VO 14.7 15 15.3 Vdc Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤ 15 W) 14.4 15 15.6 Vdc Line Regulation (Note 20)

17.9 Vdc ≤ Vin ≤ 30 Vdc, IO = 500 mA

17.5 Vdc ≤ Vin ≤ 30 Vdc, IO = 1.0 A, TJ = 25°C Regline ï ï ï 8.5 3.0 7.0 mV Load Regulation (Note 20) 5.0 mA ≤ IO ≤ 1.5 A, TJ = 25°C 5.0 mA ≤ IO ≤ 1.0 A 250 mA ≤ IO ≤ 750 mA Regload ï ï ï 1.8 1.5 1.2 mV Quiescent Current IB ï 3.5 6.0 mA Quiescent Current Change

17.5 Vdc ≤ Vin ≤ 30 Vdc, IO = 500 mA

17.5 Vdc ≤ Vin ≤ 30 Vdc, IO = 1.0 A, TJ = 25°C 5.0 mA ≤ IO ≤ 1.0 A /C0068IB ï ï ï ï ï ï 0.8 0.8 0.5 mA Ripple Rejection 18.5 Vdc ≤ Vin ≤ 28.5 Vdc, f = 120 Hz, IO = 500 mA RR 60 80 ï dB Dropout Voltage (IO = 1.0 A, TJ = 25°C) VI ï VO ï 2.0 ï Vdc Output Noise Voltage (TA = 25°C) ï 10 ï /C0109V/VO Output Resistance f = 1.0 kHz rO ï 1.2 ï m/C0087 Short Circuit Current Limit (TA = 25°C) Vin = 35 Vdc ISC ï 0.2 ï A Peak Output Current (TJ = 25°C) Imax ï 2.2 ï A Average Temperature Coefficient of Output Voltage TCVO ï ï1.0 ï mV/°C 19.Tlow = 0°C for MC78XXC, MC78XXAC, = /C004240°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB 20.Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used.

MC7800, MC7800A, MC7800AE, NCV7800 www.onsemi.com ELECTRICAL CHARACTERISTICS (Vin = 27 V, IO = 500 mA, TJ = Tlow to 125°C (Note 21), unless otherwise noted) MC7818B MC7818C Characteristic Symbol Min Typ Max Min Typ Max Unit Output Voltage (TJ = 25°C) VO 17.3 18 18.7 17.3 18 18.7 Vdc Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤ 15 W)

21 Vdc ≤ Vin ≤ 33 Vdc

22 Vdc ≤ Vin ≤ 33 Vdc

ï 17.1 ï ï 18.9 17.1 ï ï 18.9 ï Vdc Line Regulation, (Note 22)

24 Vdc ≤ Vin ≤ 30 Vdc

ï ï 9.5 3.2 360 180 ï ï 9.5 3.2 mV Load Regulation, (Note 22) 5.0 mA ≤ IO ≤ 1.5 A Regload ï 2.0 360 ï 2.0 55 mV Quiescent Current IB ï 3.5 8.0 ï 3.5 6.5 mA Quiescent Current Change 5.0 mA ≤ IO ≤ 1.0 A /C0068IB ï ï ï ï ï 0.5 ï ï ï ï 1.0 0.5 mA Ripple Rejection

22 Vdc ≤ Vin ≤ 33 Vdc, f = 120 Hz

ï 57 ï 53 57 ï dB Dropout Voltage (IO = 1.0 A, TJ = 25°C) ViI ï VO ï 2.0 ï ï 2.0 ï Vdc Output Noise Voltage (TA = 25°C) ï 10 ï ï 10 ï /C0109V/VO Output Resistance f = 1.0 kHz rO ï 1.3 ï ï 1.3 ï m/C0087 Short Circuit Current Limit (TA = 25°C) Vin = 35 Vdc ISC ï 0.2 ï ï 0.2 ï A Peak Output Current (TJ = 25°C) Imax ï 2.2 ï ï 2.2 ï A Average Temperature Coefficient of Output Voltage TCVO ï ï1.5 ï ï ï1.5 ï mV/°C 21.Tlow = 0°C for MC78XXC, MC78XXAC, = /C004240°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB 22.Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used.

MC7800, MC7800A, MC7800AE, NCV7800 www.onsemi.com ELECTRICAL CHARACTERISTICS (Vin = 27 V, IO = 1.0 A, TJ = Tlow to 125°C (Note 23), unless otherwise noted) Characteristic Symbol MC7818AC UnitMin Typ Max Output Voltage (TJ = 25°C) VO 17.64 18 18.36 Vdc Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤ 15 W) 17.3 18 18.7 Vdc Line Regulation (Note 24)

21 Vdc ≤ Vin ≤ 33 Vdc, IO = 500 mA

24 Vdc ≤ Vin ≤ 30 Vdc, IO = 1.0 A 24 Vdc ≤ Vin ≤ 30 Vdc, IO = 1.0 A, TJ = 25°C 20.6 Vdc ≤ Vin ≤ 33 Vdc, IO = 1.0 A, TJ = 25°C Regline ï ï ï ï 9.5 3.2 3.2 8.0 10.5 mV Load Regulation (Note 24) 5.0 mA ≤ IO ≤ 1.5 A, TJ = 25°C 5.0 mA ≤ IO ≤ 1.0 A 250 mA ≤ IO ≤ 750 mA Regload ï ï ï 2.0 1.8 1.5 mV Quiescent Current IB ï 3.5 6.0 mA Quiescent Current Change

21.5 Vdc ≤ Vin ≤ 30 Vdc, TJ = 25°C

5.0 mA ≤ IO ≤ 1.0 A /C0068IB ï ï ï ï ï ï 0.8 0.8 0.5 mA Ripple Rejection

22 Vdc ≤ Vin ≤ 32 Vdc, f = 120 Hz, IO = 500 mA

53 57 ï dB Dropout Voltage (IO = 1.0 A, TJ = 25°C) VI ï VO ï 2.0 ï Vdc Output Noise Voltage (TA = 25°C) ï 10 ï /C0109V/VO Output Resistance f = 1.0 kHz rO ï 1.3 ï m/C0087 Short Circuit Current Limit (TA = 25°C) Vin = 35 Vdc ISC ï 0.2 ï A Peak Output Current (TJ = 25°C) Imax ï 2.2 ï A Average Temperature Coefficient of Output Voltage TCVO ï ï1.5 ï mV/°C 23.Tlow = 0°C for MC78XXC, MC78XXAC, = /C004240°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB 24.Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used.

MC7800, MC7800A, MC7800AE, NCV7800 www.onsemi.com ELECTRICAL CHARACTERISTICS (Vin = 33 V, IO = 500 mA, TJ = Tlow to 125°C (Note 25), unless otherwise noted) MC7824B MC7824C Characteristic Symbol Min Typ Max Min Typ Max Unit Output Voltage (TJ = 25°C) VO 23 24 25 23 24 25 Vdc Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤ 15 W)

27 Vdc ≤ Vin ≤ 38 Vdc

28 Vdc ≤ Vin ≤ 38 Vdc

ï 22.8 ï ï 25.2 22.8 ï ï 25.2 ï Vdc Line Regulation, (Note 26)

30 Vdc ≤ Vin ≤ 36 Vdc

ï ï 11.5 3.8 480 240 ï ï 2.7 2.7 mV Load Regulation, (Note 26) 5.0 mA ≤ IO ≤ 1.5 A Regload ï 2.1 480 ï 4.4 65 mV Quiescent Current IB ï 3.6 8.0 ï 3.6 6.5 mA Quiescent Current Change 5.0 mA ≤ IO ≤ 1.0 A /C0068IB ï ï ï ï ï 0.5 ï ï ï ï 1.0 0.5 mA Ripple Rejection

28 Vdc ≤ Vin ≤ 38 Vdc, f = 120 Hz

ï 54 ï 50 54 ï dB Dropout Voltage (IO = 1.0 A, TJ = 25°C) VI ï VO ï 2.0 ï ï 2.0 ï Vdc Output Noise Voltage (TA = 25°C) ï 10 ï ï 10 ï /C0109V/VO Output Resistance f = 1.0 kHz rO ï 1.4 ï ï 1.4 ï m/C0087 Short Circuit Current Limit (TA = 25°C) Vin = 35 Vdc ISC ï 0.2 ï ï 0.2 ï A Peak Output Current (TJ = 25°C) Imax ï 2.2 ï ï 2.2 ï A Average Temperature Coefficient of Output Voltage TCVO ï ï2.0 ï ï ï2.0 ï mV/°C 25.Tlow = 0°C for MC78XXC, MC78XXAC, = /C004240°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB 26.Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used.

MC7800, MC7800A, MC7800AE, NCV7800 www.onsemi.com ELECTRICAL CHARACTERISTICS (Vin = 33 V, IO = 1.0 A, TJ = Tlow to 125°C (Note 27), unless otherwise noted) MC7824AC Characteristic Symbol Min Typ Max Unit Output Voltage (TJ = 25°C) VO 23.5 24 24.5 Vdc Output Voltage (5.0 mA ≤ IO ≤ 1.0 A, PD ≤ 15 W)

27.3 Vdc ≤ Vin ≤ 38 Vdc

23.2 24 25.8 Vdc Line Regulation (Note 28)

27 Vdc ≤ Vin ≤ 38 Vdc, IO = 500 mA

30 Vdc ≤ Vin ≤ 36 Vdc, IO = 1.0 A

30 Vdc ≤ Vin ≤ 36 Vdc, TJ = 25°C

26.7 Vdc ≤ Vin ≤ 38 Vdc, IO = 1.0 A, TJ = 25°C Regline ï ï ï ï 11.5 3.8 3.8 mV Load Regulation (Note 28) 5.0 mA ≤ IO ≤ 1.5 A, TJ = 25°C 5.0 mA ≤ IO ≤ 1.0 A 250 mA ≤ IO ≤ 750 mA Regload ï ï ï 2.1 2.0 1.8 mV Quiescent Current IB ï 3.6 6.0 mA Quiescent Current Change

27.3 Vdc ≤ Vin ≤ 38 Vdc, IO = 500 mA

27 Vdc ≤ Vin ≤ 38 Vdc, TJ = 25°C

5.0 mA ≤ IO ≤ 1.0 A /C0068IB ï ï ï ï ï ï 0.8 0.8 0.5 mA Ripple Rejection

28 Vdc ≤ Vin ≤ 38 Vdc, f = 120 Hz, IO = 500 mA

45 54 ï dB Dropout Voltage (IO = 1.0 A, TJ = 25°C) VI ï VO ï 2.0 ï Vdc Output Noise Voltage (TA = 25°C) ï 10 ï /C0109V/VO Output Resistance (f = 1.0 kHz) rO ï 1.4 ï m/C0087 Short Circuit Current Limit (TA = 25°C) Vin = 35 Vdc ISC ï 0.2 ï A Peak Output Current (TJ = 25°C) Imax ï 2.2 ï A Average Temperature Coefficient of Output Voltage TCVO ï ï2.0 ï mV/°C 27.Tlow = 0°C for MC78XXC, MC78XXAC, = /C004240°C for NCV78XX, MC78XXB, MC78XXAB, and MC78XXAEB 28.Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used.

current as the voltage across the pass transistor is increased. Figure 9. Current Regulator Figure 10. Adjustable Output Re gulator Figure 11. Current Boost Regulator Figure 12. Short Circuit Protection

10 W resistor and the output voltage compliance wou ld be the input

IB /C0094 3.2 mA over line and load changes. increased by VBE of the pass transistor. XX = 2 digits of type number indicating voltage. four-ampere plastic power transistor is specified. XX = 2 digits of type number indicating voltage.

MC7800, MC7800A, MC7800AE, NCV7800 www.onsemi.com DEFINITIONS Line Regulation ï The change in output voltage for a change in the input voltage. The measurement is made under conditions of low dissipation or by using pulse techniques such that the average chip temperature is not significantly affected. Load Regulation ï The change in output voltage for a change in load current at constant chip temperature. Maximum Power Dissipation ï The maximum total device dissipation for which the regulator will operate within specifications. Quiescent Current ï That part of the input current that is not delivered to the load. Output Noise Voltage ï The rms ac voltage at the output, with constant load and no input ripple, measured ov er a specified frequency range. Long Term Stability ï Output voltage stability under accelerated life test conditions with the maximum rated voltage listed in the devices electrical characteristics and maximum power dissipation. Temperature Range Package Shipping MC7805ABD2TR4G 5.0 V TJ = ï40°C to +125°C D2PAK (Pbïfree) 800 / Tape & Reel NCV7805ABD2TR4G* 5.0 V TJ = ï40°C to +125°C D2PAK (Pbïfree) 800 / Tape & Reel MC7805ABTG 5.0 V TJ = ï40°C to +125°C TOï220 (Pbïfree)

50 Units /Rail

MC7805ACD2TG 5.0 V TJ = 0°C to +125°C D2PAK (Pbïfree) MC7805ACD2TR4G 5.0 V TJ = 0°C to +125°C D2PAK (Pbïfree) 800 / Tape & Reel MC7805ACTG 5.0 V TJ = 0°C to +125°C TOï220 (Pbïfree) MC7805BD2TG 5.0 V TJ = ï40°C to +125°C D2PAK (Pbïfree) MC7805BD2TR4G 5.0 V TJ = ï40°C to +125°C D2PAK (Pbïfree) 800 / Tape & Reel MC7805BDTG 5.0 V TJ = ï40°C to +125°C DPAK (Pbïfree)

75 Units / Rail

MC7805BDTRKG 5.0 V TJ = ï40°C to +125°C DPAK (Pbïfree) 2500 / Tape & Reel NCV7805BDTRKG* 5.0 V TJ = ï40°C to +125°C DPAK (Pbïfree) 2500 / Tape & Reel MC7805BTG 5.0 V TJ = ï40°C to +125°C TOï220 (Pbïfree) NCV7805BTG* 5.0 V TJ = ï40°C to +125°C TOï220 (Pbïfree) NCV7805BD2TG* 5.0 V TJ = ï40°C to +125°C D2PAK (Pbïfree) NCV7805BD2TR4G* 5.0 V TJ = ï40°C to +125°C D2PAK (Pbïfree) 800 / Tape & Reel MC7805CD2TG 5.0 V TJ = 0°C to +125°C D2PAK (Pbïfree) MC7805CD2TR4G 5.0 V TJ = 0°C to +125°C D2PAK (Pbïfree) 800 / Tape & Reel MC7805CDTG 5.0 V TJ = 0°C to +125°C DPAK (Pbïfree) For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Spe- cifications Brochure, BRD8011/D. *NCV devices: Tlow = ï40°C, Thigh = +125°C. Guaranteed by design. NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AECïQ100 Qualified and PPAP Capable.

MC7800, MC7800A, MC7800AE, NCV7800 www.onsemi.com ORDERING INFORMATION (continued) Device Shipping Package Operating Temperature RangeNominal Voltage MC7805CDTRKG 5.0 V TJ = 0°C to +125°C DPAK (Pbïfree) 2500 / Tape & Reel MC7805CTG 5.0 V TJ = 0°C to +125°C TOï220 (Pbïfree) NCV7808ABD2TR4G* 8.0 V TJ = ï40°C to +125°C D2PAK (Pbïfree) 800 / Tape & Reel MC7808AEBTG 8.0 V TJ = ï40°C to +125°C TOï220 (Pbïfree)

50 Units / Rail

NCV7808BD2TR4G* 8.0 V TJ = ï40°C to +125°C D2PAK (Pbïfree) 800 / Tape & Reel NCV7808BDTG* 8.0 V TJ = ï40°C to +125°C DPAK (Pbïfree) NCV7808BDTRKG* 8.0 V TJ = ï40°C to +125°C DPAK (Pbïfree) 2500 / Tape & Reel NCV7808BTG* 8.0 V TJ = ï40°C to +125°C TOï220 (Pbïfree) MC7808CDTRKG 8.0 V TJ = 0°C to +125°C DPAK (Pbïfree) 2500 / Tape & Reel MC7808CTG 8.0 V TJ = 0°C to +125°C TOï220 (Pbïfree) MC7809ABTG 9.0 V TJ = ï40°C to +125°C TOï220 (Pbïfree) NCV7809BD2TR4G* 9.0 V TJ = ï40°C to +125°C D2PAK (Pbïfree) 800 / Tape & Reel NCV7809BTG* 9.0 V TJ = ï40°C to +125°C TOï220 (Pbïfree) MC7809CTG 9.0 V TJ = 0°C to +125°C TOï220 (Pbïfree) MC7812ABD2TR4G 12 V TJ = ï40°C to +125°C D2PAK (Pbïfree) 800 / Tape & Reel NCV7812ABTG* 12 V TJ = ï40°C to +125°C TOï220 (Pbïfree) MC7812ACD2TR4G 12 V TJ = 0°C to +125°C D2PAK (Pbïfree) 800 / Tape & Reel MC7812ACTG 12 V TJ = 0°C to +125°C TOï220 (Pbïfree) MC7812BD2TR4G 12 V TJ = ï40°C to +125°C D2PAK (Pbïfree) 800 / Tape & Reel NCV7812BD2TR4G* 12 V TJ = ï40°C to +125°C D2PAK (Pbïfree) 800 / Tape & Reel MC7812BDTG 12 V TJ = ï40°C to +125°C DPAK (Pbïfree) MC7812BDTRKG 12 V TJ = ï40°C to +125°C DPAK (Pbïfree) 2500 / Tape & Reel MC7812BTG 12 V TJ = ï40°C to +125°C TOï220 (Pbïfree) NCV7812BTG* 12 V TJ = ï40°C to +125°C TOï220 (Pbïfree) For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Spe- cifications Brochure, BRD8011/D. *NCV devices: Tlow = ï40°C, Thigh = +125°C. Guaranteed by design. NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AECïQ100 Qualified and PPAP Capable.

MC7800, MC7800A, MC7800AE, NCV7800 www.onsemi.com ORDERING INFORMATION (continued) Device Shipping Package Operating Temperature RangeNominal Voltage MC7812CD2TR4G 12 V TJ = 0°C to +125°C D2PAK (Pbïfree) 800 / Tape & Reel MC7812CDTRKG 12 V TJ = 0°C to +125°C DPAK (Pbïfree) 2500 / Tape & Reel MC7812CTG 12 V TJ = 0°C to +125°C TOï220 (Pbïfree) MC7815ABD2TR4G 15 V TJ = ï40°C to +125°C D2PAK (Pbïfree) 800 / Tape & Reel MC7815ABTG 15 V TJ = ï40°C to +125°C TOï220 (Pbïfree) MC7815ACTG 15 V TJ = 0°C to +125°C TOï220 (Pbïfree) MC7815BD2TR4G 15 V TJ = ï40°C to +125°C D2PAK (Pbïfree) 800 / Tape & Reel MC7815BDTRKG 15 V TJ = ï40°C to +125°C DPAK (Pbïfree) 2500 / Tape & Reel MC7815BTG 15 V TJ = ï40°C to +125°C TOï220 (Pbïfree) NCV7815BTG* 15 V TJ = ï40°C to +125°C TOï220 (Pbïfree) MC7815CD2TG 15 V TJ = 0°C to +125°C D2PAK (Pbïfree) MC7815CD2TR4G 15 V TJ = 0°C to +125°C D2PAK (Pbïfree) 800 / Tape & Reel MC7815CDTRKG 15 V TJ = 0°C to +125°C DPAK (Pbïfree) 2500 / Tape & Reel MC7815CTG 15 V TJ = 0°C to +125°C TOï220 (Pbïfree) MC7818BTG 18 V TJ = ï40°C to +125°C TOï220 (Pbïfree) MC7818CD2TR4G 18 V TJ = 0°C to +125°C D2PAK (Pbïfree) 800 / Tape & Reel MC7818CTG 18 V TJ = 0°C to +125°C TOï220 (Pbïfree) MC7824ACTG 24 V TJ = 0°C to +125°C TOï220 (Pbïfree) MC7824BTG 24 V TJ = ï40°C to +125°C TOï220 (Pbïfree) MC7824CD2TR4G 24 V TJ = 0°C to +125°C D2PAK (Pbïfree) 800 / Tape & Reel MC7824CTG 24 V TJ = 0°C to +125°C TOï220 (Pbïfree) For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Spe- cifications Brochure, BRD8011/D. *NCV devices: Tlow = ï40°C, Thigh = +125°C. Guaranteed by design. NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AECïQ100 Qualified and PPAP Capable.

MC7800, MC7800A, MC7800AE, NCV7800 www.onsemi.com 78xxAyD2T AWLYWWG MC 78xxAyT AWLYWWG xx = 05, 06, 08, 09, 12, 15, 18, or 24 y = B or C A = Assembly Location WL, L = Wafer Lot Y = Year WW = Work Week G = Pb ïFree Device MARKING DIAGRAMS TOï220ï3 T SUFFIX CASE 221A MC D2PAKï3 D2T SUFFIX CASE 936 DPAKï3 DT SUFFIX CASE 369C 78xxyG ALYWW78xxyD2T AWLYWWG MC * MC 78xxyT AWLYWWG *This marking diagram also applies to NCV78xx family. MC 78xxAEyT AWLYWWG

TOï220, SINGLE GAUGE CASE 221ABï01 ISSUE A DATE 16 NOV 2010 SCALE 1:1 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCHES. 3. DIMENSION Z DEFINES A ZONE WHERE ALL BODY AND LEAD IRREGULARITIES ARE ALLOWED. 4. PRODUCT SHIPPED PRIOR TO 2008 HAD DIMENSIONS S = 0.045 - 0.055 INCHES (1.143 - 1.397 MM) STYLE 1: PIN 1. BASE 2. COLLECTOR 3. EMITTER 4. COLLECTOR STYLE 2: PIN 1. BASE 2. EMITTER 3. COLLECTOR 4. EMITTER STYLE 3: PIN 1. CATHODE 2. ANODE 3. GATE 4. ANODE STYLE 4: PIN 1. MAIN TERMINAL 1 2. MAIN TERMINAL 2 3. GATE 4. MAIN TERMINAL 2 STYLE 7: PIN 1. CATHODE 2. ANODE 3. CATHODE 4. ANODE STYLE 10: PIN 1. GATE 2. SOURCE 3. DRAIN 4. SOURCE STYLE 5: PIN 1. GATE 2. DRAIN 3. SOURCE 4. DRAIN STYLE 8: PIN 1. CATHODE 2. ANODE 3. EXTERNAL TRIP/DELAY 4. ANODE STYLE 6: PIN 1. ANODE 2. CATHODE 3. ANODE 4. CATHODE STYLE 9: PIN 1. GATE 2. COLLECTOR 3. EMITTER 4. COLLECTOR STYLE 11: PIN 1. DRAIN 2. SOURCE 3. GATE 4. SOURCE DIM MIN MAX MIN MAX MILLIMETERS INCHES A 0.570 0.620 14.48 15.75 B 0.380 0.405 9.66 10.28 C 0.160 0.190 4.07 4.82 D 0.025 0.035 0.64 0.88 F 0.142 0.147 3.61 3.73 G 0.095 0.105 2.42 2.66 H 0.110 0.155 2.80 3.93 J 0.018 0.025 0.46 0.64 K 0.500 0.562 12.70 14.27 L 0.045 0.060 1.15 1.52 N 0.190 0.210 4.83 5.33 Q 0.100 0.120 2.54 3.04 R 0.080 0.110 2.04 2.79 S 0.020 0.024 0.508 0.61 T 0.235 0.255 5.97 6.47 U 0.000 0.050 0.00 1.27 B Q H Z L V G N A K F 1 2 3 D SEATING PLANE ïTï C ST U R J MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the rights of others. 98AON23085DDOCUMENT NUMBER: DESCRIPTION: Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped CONTROLLED COPY in red. PAGE 1 OF 1TOï220, SINGLE GAUGE  Semiconductor Components Industries, LLC, 2019 www.onsemi.com

DPAK (SINGLE GAUGE) CASE 369C ISSUE F DATE 21 JUL 2015 SCALE 1:1 STYLE 1: PIN 1. BASE 2. COLLECTOR 3. EMITTER 4. COLLECTOR STYLE 2: PIN 1. GATE 2. DRAIN 3. SOURCE 4. DRAIN STYLE 3: PIN 1. ANODE 2. CATHODE 3. ANODE 4. CATHODE STYLE 4: PIN 1. CATHODE 2. ANODE 3. GATE 4. ANODE STYLE 5: PIN 1. GATE 2. ANODE 3. CATHODE 4. ANODE STYLE 6: PIN 1. MT1 2. MT2 3. GATE 4. MT2 STYLE 7: PIN 1. GATE 2. COLLECTOR 3. EMITTER 4. COLLECTOR 1 2 STYLE 8: PIN 1. N/C 2. CATHODE 3. ANODE 4. CATHODE STYLE 9: PIN 1. ANODE 2. CATHODE 3. RESISTOR ADJUST 4. CATHODE STYLE 10: PIN 1. CATHODE 2. ANODE 3. CATHODE 4. ANODE b D E M0.005 (0.13) C A c C Z DIM MIN MAX MIN MAX MILLIMETERS INCHES D 0.235 0.245 5.97 6.22 E 0.250 0.265 6.35 6.73 A 0.086 0.094 2.18 2.38 b 0.025 0.035 0.63 0.89 c2 0.018 0.024 0.46 0.61 b2 0.028 0.045 0.72 1.14 c 0.018 0.024 0.46 0.61 e 0.090 BSC 2.29 BSC b3 0.180 0.215 4.57 5.46 L4 ïïï 0.040 ïïï 1.01 L 0.055 0.070 1.40 1.78 L3 0.035 0.050 0.89 1.27 Z 0.155 ïïï 3.93 ïïï NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: INCHES. 3. THERMAL PAD CONTOUR OPTIONAL WITHIN DI- MENSIONS b3, L3 and Z. 4. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR BURRS. MOLD FLASH, PROTRUSIONS, OR GATE BURRS SHALL NOT EXCEED 0.006 INCHES PER SIDE. 5. DIMENSIONS D AND E ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY. 6. DATUMS A AND B ARE DETERMINED AT DATUM PLANE H. 7. OPTIONAL MOLD FEATURE. 1 2 3 XXXXXX = Device Code A = Assembly Location L = Wafer Lot Y = Year WW = Work Week G = Pb ïFree Package AYWW XXX XXXXXG XXXXXXG ALYWW Discrete IC 5.80 0.228 2.58 0.102 1.60 0.063 6.20 0.244 3.00 0.118 6.17 0.243 /C0466mm inches/C0467SCALE 3:1 GENERIC MARKING DIAGRAM* *For additional information on our PbïFree strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. SOLDERING FOOTPRINT* H 0.370 0.410 9.40 10.41 A1 0.000 0.005 0.00 0.13 L1 0.114 REF 2.90 REF L2 0.020 BSC 0.51 BSC HDETAIL A SEATING PLANE A B C L H L2 GAUGE PLANE DETAIL A ROTATED 90 CW/C0053 e BOTTOM VIEW Z BOTTOM VIEW SIDE VIEW TOP VIEW ALTERNATE CONSTRUCTIONS NOTE 7 Z *This information is generic. Please refer to device data sheet for actual part marking. PbïFree indicator, G or microdot /C0071, may or may not be present. Some products may not follow the Generic Marking. MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS 98AON10527DDOCUMENT NUMBER: DESCRIPTION: Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped CONTROLLED COPY in red. PAGE 1 OF 1DPAK (SINGLE GAUGE) onsemi and are trademarks of Semiconductor Components Industries, LLC dba onsemi or its subsidiaries in the United States and/or other countries. onsemi reserves the right to make changes without further notice to any products herein. onsemi makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. onsemi does not convey any license under its patent rights nor the rights of others.  Semiconductor Components Industries, LLC, 2018 www.onsemi.com

SCALE 1:1 D2PAK CASE 936ï03 ISSUE E DATE 29 SEP 2015 V U TERMINAL 4 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCHES. 3. TAB CONTOUR OPTIONAL WITHIN DIMENSIONS A AND K. 4. DIMENSIONS U AND V ESTABLISH A MINIMUM MOUNTING SURFACE FOR TERMINAL 4. 5. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH OR GATE PROTRUSIONS. MOLD FLASH AND GATE PROTRUSIONS NOT TO EXCEED 0.025 (0.635) MAXIMUM. 6. SINGLE GAUGE DESIGN WILL BE SHIPPED AF TER FPCN EXPIRATION IN OCTOBER 2011. DIM A MIN MAX MIN MAX MILLIMETERS 0.386 0.403 9.804 10.236 INCHES B 0.356 0.368 9.042 9.347 C 0.170 0.180 4.318 4.572 D 0.026 0.036 0.660 0.914 E 0.045 0.055 1.143 1.397 F 0.051 REF 1.295 REF G 0.100 BSC 2.540 BSC H 0.539 0.579 13.691 14.707 J 0.125 MAX 3.175 MAX K 0.050 REF 1.270 REF L 0.000 0.010 0.000 0.254 M 0.088 0.102 2.235 2.591 N 0.018 0.026 0.457 0.660 P 0.058 0.078 1.473 1.981 R S 0.116 REF 2.946 REF U 0.200 MIN 5.080 MIN V 0.250 MIN 6.350 MIN /C0095 A 1 2 3 K F B J S H D M0.010 (0.254) T EOPTIONAL CHAMFER *For additional information on our PbïFree strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. SOLDERING FOOTPRINT* 8.380 5.080 DIMENSIONS: MILLIMETERSPITCH 16.155 1.0162X 10.490 3.504 XXXXXXG ALYWW GENERIC MARKING DIAGRAM* XXXXXX = Specific Device Code A = Assembly Location L = Wafer Lot Y = Year WW = Work Week G = Pb ïFree Package *This information is generic. Please refer to device data sheet for actual part marking. PbïFree indicator, G or microdot /C0071, may or may not be present. BOTTOM VIEW OPTIONAL CONSTRUCTIONS TOP VIEW SIDE VIEW DUAL GAUGE BOTTOM VIEW L T P R DETAIL C SEATING PLANE G N M CONSTRUCTION D C DETAIL C EOPTIONAL CHAMFER SIDE VIEW SINGLE GAUGE CONSTRUCTION S C DETAIL C TT D E 0.018 0.026 0.457 0.660S 8/C00950/C00958/C0095 MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the rights of others. 98ASH01005ADOCUMENT NUMBER: DESCRIPTION: Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped CONTROLLED COPY in red. PAGE 1 OF 1 D2PAK  Semiconductor Components Industries, LLC, 2019 www.onsemi.com

onsemi, , and other names, marks, and brands are registe red and/or common law trademarks of Semiconductor Components Industries, LLC dba onsemi or its affiliates and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of onsemis product/patent coverage may be accessed at www.onsemi.com/site/pdf/PatentïMarking.pdf. onsemi reserves the right to make changes at any time to any products or information herein, without notice. The information herein is provided asïis and onsemi makes no warranty, representation or guarantee regarding the accuracy of the information, product features, availability, functionality, or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using onsemi products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by onsemi. Typical parameters which may be provided in onsemi data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including Typicals must be validated for each customer application by customers technical experts. onsemi does not convey any license under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and hold onsemi and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION TECHNICAL SUPPORT North American Technical Support: Voice Mail: 1 800ï282ï9855 Toll Free USA/Canada Phone: 011 421 33 790 2910 LITERATURE FULFILLMENT: Email Requests to: orderlit@onsemi.com onsemi Website: www.onsemi.com Europe, Middle East and Africa Technical Support: Phone: 00421 33 790 2910 For additional information, please contact your local Sales Representative

Product Information

MC7805B specifications and overview.

Summary

Voltage Regulators - Positive 1.0 A November, 2021 - Rev. 29

Description

Voltage Regulators - Positive 1.0 A November, 2021 - Rev. 29

Source title MC7805B Datasheet(PDF) - ON Semiconductor

Related Parts

More parts from the same family.

Browse manufacturer