MPC7410 FREESCALE | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 8
Technical content
This document contains information on a new product. Specifications and information herein are subject to change without notice. © Freescale Semiconductor, Inc., 2002, 2007. All rights reserved. Freescale Semiconductor Advance Information This document describes part number-specific changes to recommended operating conditions and revised electrical specifications, as applicable, from those described in the general MPC7410 Hardware Specifications (Document No. MPC7410EC). Specifications provided in this document supersede those in the MPC7410 Hardware Specifications, for the part numbers listed in Table A only. Specifications not addressed herein are unchanged. Because this document is frequently updated, refer to http://www.freescale.com or to your Freescale sales office for the latest version. Note that headings and table numbers in this document are not consecutively numbered. They are intended to correspond to the heading or table affected in the general hardware specification. Part numbers addressed in this document are listed in Table A. For more detailed ordering information see Table 17. Document Number: MPC7410ECS02AD Rev. 2.0, 11/2007 Freescale Part Numbers Affected: MPC7410RX400NE MPC7410HX400NE MPC7410VS400NE MC7410VU400NE MPC7410RX450NE MPC7410HX450NE MPC7410VS450NE MC7410VU450NE --- Preliminary --- MPC7410 RISC Microprocessor Hardware Specifications Addendum for the MPC7410 xxnnnNE Series
MPC7410 RISC Microprocessor Hardware Specifications Addendum for the MPC7410xxnnnNE Series, Rev. 2.0
2 Freescale Semiconductor
Features
2 Features
This section summarizes changes to the features of the MPC7410 described in the MPC7410 Hardware Specifications.
- Bus interface — Selectable interface voltages of 1.8 V , 2.5 V (3.3 V not supported)
4.1 DC Electrical Characteristics
V oltage to the L2 I/Os and processor interface I/Os are provided through separate sets of supply pins and may be provided at the voltages shown in Table 2. Table A. Part Numbers Addressed by this Data Sheet Freescale Part Number Operating Conditions Significant Differences from Hardware SpecificationCPU Frequency Vdd T J (°C) OVdd MPC7410RX400NE MPC7410HX400NE MPC7410VS400NE MC7410VU400NE 400 MHz 1.5V±50mV 0 to 105 1.8/2.5 V Reduced core voltage to achieve lower power consumption. Removes 3.3V OVdd support. For all AC/DC specifications not mentioned in this document, please refer to the MPC7410(RX/HX/VS)400LE and MC7410VU400LE specifications in the general MPC7410 Hardware Specifications . 450 MHz 1.8V ±100mV 0 to 105 1.8/2.5/3.3 V The MPC7410(RX/HX/VS)400NE and MC7410VU400NE also fully conform to the MPC7410(RX/HX/VS)450LE and MC7410VU450LE specifications, respectively. Refer to the general MPC7410 Hardware Specifications. MPC7410RX450NE MPC7410HX450NE MPC7410VS450NE MC7410VU450NE 450 MHz 1.5V±50mV 0 to 105 1.8/2.5 V Reduced core voltage to achieve lower power consumption. Removes 3.3V OVdd support. For all AC/DC specifications not mentioned in this document, please refer to the MPC7410(RX/HX/VS)450LE and MC7410VU450LE specifications in the general MPC7410 Hardware Specifications . 500 MHz 1.8V ±100mV 0 to 105 1.8/2.5/3.3 V The MPC7410(RX/HX/VS)450NE and MC7410VU400NE also fully conform to the MPC7410(RX/HX/VS)500LE and MC7410VU500LE specifications, respectively. Refer to the general MPC7410 Hardware Specifications.
MPC7410 RISC Microprocessor Hardware Specifications Addendum for the MPC7410xxnnnNE Series, Rev. 2.0 Freescale Semiconductor 3 Table 3 provides the recommended operating conditions for the MPC7410 part numbers described herein. Table 2. Input Threshold Voltage Setting
- Caution: The input threshold selection must agree with the OVdd/L2OVdd voltages supplied.
- T o select the 2.5-V threshold option, BVSEL and/or L2VSEL should be tied to HRESET so that the two signals
change state together. This is the preferred method for selecting this mode of operation.
- T o overcome the internal pull-up resistance, a pull-down resistance less than 250 ohms should be used.
- Default voltage setting if left unconnected (internal pulled-up).
- Caution: The XPC7410RXnnnNE does not support the default OVdd setting of 3.3 V . The BVSEL input must be tie
Table 3. Recommended Operating Conditions these conditions is not guaranteed.
MPC7410 RISC Microprocessor Hardware Specifications Addendum for the MPC7410xxnnnNE Series, Rev. 2.0
4 Freescale Semiconductor
Table 7 provides the power consumption for the MPC7410 part at the frequencies described herein. Table 7. Power Consumption for MPC7410
- These values apply for all valid processor bus and L2 bus ratios. The values
- Maximum power is measured at 105 °C and Vdd = 1.5V while running an
execution units, including AltiVec, maximally busy.
- T ypical power is an average value measured at 65 °C and Vdd = 1.5V in a
system while running typical benchmarks.
9 Document Revision History
Table 16 provides a revision history for this Hardware Specification Addendum. Table 16. Document Revision History were added to this specification. MPC7410VS450NE, and MC7410VU450NE devices to list on cover page and to Table A. MPC7410ECS02AD for Hardware Specification Addendum. Added Section 1.9 Document Revision History. Section 1.10.1 - added T able 17 - Part Marking Nomenclature.
0 Initial release
MPC7410 RISC Microprocessor Hardware Specifications Addendum for the MPC7410xxnnnNE Series, Rev. 2.0
6 Freescale Semiconductor
Ordering Information
10.1 Part Numbers Addressed by this Specification
Table 17 provides the ordering information for the MPC7410 part described in this document. Table 17. Part Marking Nomenclature.
10.3 Part Marking
Parts are marked as the example shown in Figure 26. Figure 26. Freescale Part Marking for BGA Device
- Processor core frequencies supported by parts are addressed by this specification only. Parts addressed by other
specifications may support other maximum core frequencies.
MPC7410 RISC Microprocessor Hardware Specifications Addendum for the MPC7410xxnnnNE Series, Rev. 2.0 Freescale Semiconductor 7 THIS PAGE INTENTIONALLY LEFT BLANK
Document Number: MPC7410ECS02AD Rev. 2.0 Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. The Power Architecture and Power.org word marks and the Power and Power.org logos and related marks are trademarks and service marks licensed by Power.org. © Freescale Semiconductor, Inc., 2002, 2007. Printed in the United States of America. All rights reserved. Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. How to Reach Us: Home Page: www.freescale.com email: support@freescale.com USA/Europe or Locations Not Listed: Freescale Semiconductor Technical Information Center, CH370 1300 N. Alma School Road Chandler, Arizona 85224 (800) 521-6274 480-768-2130 support@freescale.com Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) support@freescale.com Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku Tokyo 153-0064, Japan 0120 191014 +81 2666 8080 support.japan@freescale.com Asia/Pacific: Freescale Semiconductor Hong Kong Ltd. Technical Information Center
2 Dai King Street
Tai Po Industrial Estate, Tai Po, N.T., Hong Kong +800 2666 8080 support.asia@freescale.com For Literature Requests Only: Freescale Semiconductor Literature Distribution Center P .O. Box 5405 Denver, Colorado 80217 (800) 441-2447 303-675-2140 Fax: 303-675-2150 LDCForFreescaleSemiconductor @hibbertgroup.com