MC54-74HC240A MOTOROLA | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 7

Technical content

/C0077/C0079/C0084/C0079/C0082/C0079/C0076/C0065 SEMICONDUCTOR TECHNICAL DATA 1 REV 7 Motorola, Inc. 1997 /C0079/C0099/C0116/C0097/C0108 /C0051/C0045/C0083/C0116/C0097/C0116/C0101 /C0073/C0110/C0118/C0101/C0114/C0116/C0105/C0110/C0103 /C0066/C0117/C0102/C0102/C0101/C0114/C0047 /C0076/C0105/C0110/C0101 /C0068/C0114/C0105/C0118/C0101/C0114/C0047/C0076/C0105/C0110/C0101 /C0082/C0101/C0099/C0101/C0105/C0118/C0101/C0114 High–Performance Silicon–Gate CMOS The MC54/74HC240A is identical in pinout to the LS240. The device inputs are compatible with standard CMOS outputs; with pullup resistors, they are compatible with LSTTL outputs. This octal noninverting buffer/line driver/line receiver is designed to be used with 3–state memory address drivers, clock drivers, and other sub–oriented systems. The device has inverting outputs and two active–low output enables. The HC240A is similar in function to the HC241A and HC244A.

  • Output Drive Capability: 15 LSTTL Loads
  • Outputs Directly Interface to CMOS, NMOS, and TTL
  • Operating Voltage Range: 2 to 6 V
  • Low Input Current: 1 µA
  • High Noise Immunity Characteristic of CMOS Devices
  • In Compliance with the Requirements Defined by JEDEC Standard No. 7A
  • Chip Complexity: 120 FETs or 30 Equivalent Gates LOGIC DIAGRAM DATA INPUTS B4 17 21 8

3 YB4

PIN 20 = VCC PIN 10 = GNDOUTPUT ENABLES ENABLE A ENABLE B /C0077/C0067/C0053/C0052/C0047/C0055/C0052/C0072/C0067/C0050/C0052/C0048/C0065 PIN ASSIGNMENT YB4 ENABLE A GND YB1 YB2 YB3 5 YA2 YA1 ENABLE B VCC YA4 YA3 FUNCTION TABLE Inputs Outputs Enable A, Enable B A, B YA, YB LLH LHL HXZ Z = high impedance DW SUFFIX SOIC PACKAGE CASE 751D–04 N SUFFIX PLASTIC PACKAGE CASE 738–03

ORDERING INFORMATION

CASE 948E–02 J SUFFIX CERAMIC PACKAGE CASE 732–03

MOTOROLA High–Speed CMOS Logic Data DL129 — Rev 6 ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ MAXIMUM RATINGS* ÎÎÎ ÎÎÎ Symbol ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Parameter ÎÎÎÎÎÎ ÎÎÎÎÎÎ Value ÎÎÎ ÎÎÎ Unit ÎÎÎ ÎÎÎ VCC ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ DC Supply Voltage (Referenced to GND) ÎÎÎÎÎÎ ÎÎÎÎÎÎ – 0.5 to + 7.0 ÎÎÎ ÎÎÎ V ÎÎÎ ÎÎÎ Vin ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ DC Input Voltage (Referenced to GND) ÎÎÎÎÎÎ ÎÎÎÎÎÎ – 0.5 to VCC + 0.5 ÎÎÎ ÎÎÎ V ÎÎÎ ÎÎÎ Vout ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ DC Output Voltage (Referenced to GND) ÎÎÎÎÎÎ ÎÎÎÎÎÎ – 0.5 to VCC + 0.5 ÎÎÎ ÎÎÎ V ÎÎÎ ÎÎÎ Iin ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ DC Input Current, per Pin ÎÎÎÎÎÎ ÎÎÎÎÎÎ ± 20 ÎÎÎ ÎÎÎ mA ÎÎÎ ÎÎÎ Iout ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ DC Output Current, per Pin ÎÎÎÎÎÎ ÎÎÎÎÎÎ ± 35 ÎÎÎ ÎÎÎ mA ÎÎÎ ÎÎÎ ICC ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ DC Supply Current, VCC and GND Pins ÎÎÎÎÎÎ ÎÎÎÎÎÎ ± 75 ÎÎÎ ÎÎÎ mA ÎÎÎ Î Î Î Î Î Î PD ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎÎÎÎÎÎ Î Î ÎÎÎÎÎÎÎÎÎÎÎÎ Î Power Dissipation in Still Air, Plastic or Ceramic DIP† ÎÎÎÎÎÎ Î ÎÎÎÎ Î Î ÎÎÎÎ Î 750 500 450 ÎÎÎ Î Î Î Î Î Î mW ÎÎÎ Î Î Î Tstg ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎÎÎÎÎÎ Î Storage Temperature ÎÎÎÎÎÎ Î ÎÎÎÎ Î – 65 to + 150 ÎÎÎ Î Î Î /C0095C ÎÎÎ Î Î Î Î Î Î ÎÎÎ TL ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎÎÎÎÎÎ Î Î ÎÎÎÎÎÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Lead Temperature, 1 mm from Case for 10 Seconds (Plastic DIP, SOIC or TSSOP Package) (Ceramic DIP) ÎÎÎÎÎÎ Î ÎÎÎÎ Î Î ÎÎÎÎ Î ÎÎÎÎÎÎ 260 300 ÎÎÎ Î Î Î Î Î Î ÎÎÎ /C0095C * Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. †Derating — Plastic DIP: – 10 mW//C0095C from 65/C0095 to 125/C0095C Ceramic DIP: – 10 mW//C0095C from 100/C0095 to 125/C0095C For high frequency or heavy load considerations, see Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D). RECOMMENDED OPERATING CONDITIONS ÎÎÎÎ ÎÎÎÎ Symbol ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Parameter ÎÎÎ ÎÎÎ Min ÎÎÎ ÎÎÎ Max ÎÎÎ ÎÎÎ Unit ÎÎÎÎ ÎÎÎÎ VCC ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ DC Supply Voltage (Referenced to GND) ÎÎÎ ÎÎÎ 2.0 ÎÎÎ ÎÎÎ 6.0 ÎÎÎ ÎÎÎ V ÎÎÎÎ ÎÎÎÎ Vin, Vout ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ DC Input Voltage, Output Voltage (Referenced to GND) ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ VCC ÎÎÎ ÎÎÎ V ÎÎÎÎ ÎÎÎÎ TA ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Operating Temperature, All Package Types ÎÎÎ ÎÎÎ – 55 ÎÎÎ ÎÎÎ + 125 ÎÎÎ ÎÎÎ /C0095C ÎÎÎÎ Î ÎÎ Î Î ÎÎ Î tr, tf ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎÎÎÎÎÎ Î Î ÎÎÎÎÎÎÎÎÎÎÎÎ Î Input Rise and Fall Time V CC = 2.0 V (Figure 1) V CC = 4.5 V VCC = 6.0 V ÎÎÎ Î Î Î Î Î Î ÎÎÎ Î Î Î Î Î Î 1000 500 400 ÎÎÎ Î Î Î Î Î Î ns DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND) ÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎ Guaranteed Limit ÎÎÎ ÎÎÎ ÎÎÎÎ Î ÎÎ Î ÎÎÎÎ Symbol ÎÎÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎÎÎ Parameter ÎÎÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎÎÎ Test Conditions ÎÎÎÎ Î ÎÎ Î ÎÎÎÎ VCC V ÎÎÎ Î ÎÎ ÎÎÎ – 55 to 25/C0095C ÎÎÎÎ Î ÎÎ Î ÎÎÎÎ /C0118 85/C0095C ÎÎÎÎ Î ÎÎ Î ÎÎÎÎ /C0118 125/C0095C ÎÎÎ Î Î Î ÎÎÎ Unit ÎÎÎÎ Î ÎÎ Î Î ÎÎ Î ÎÎÎÎ VIH ÎÎÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎ Î Î ÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎÎÎ Minimum High–Level Input Voltage ÎÎÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎ Î Î ÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎÎÎ Vout = VCC – 0.1 V |Iout| /C0118 20 µA ÎÎÎÎ Î ÎÎ Î Î ÎÎ Î ÎÎÎÎ 2.0 3.0 4.5 6.0 ÎÎÎ Î ÎÎ Î ÎÎ ÎÎÎ 1.5 2.1 3.15 4.2 ÎÎÎÎ Î ÎÎ Î Î ÎÎ Î ÎÎÎÎ 1.5 2.1 3.15 4.2 ÎÎÎÎ Î ÎÎ Î Î ÎÎ Î ÎÎÎÎ 1.5 2.1 3.15 4.2 ÎÎÎ Î Î Î Î Î Î ÎÎÎ V ÎÎÎÎ Î ÎÎ Î Î ÎÎ Î ÎÎÎÎ VIL ÎÎÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎ Î Î ÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎÎÎ Maximum Low–Level Input Voltage ÎÎÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎ Î Î ÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎÎÎ Vout = 0.1 V |Iout| /C0118 20 µA ÎÎÎÎ Î ÎÎ Î Î ÎÎ Î ÎÎÎÎ 2.0 3.0 4.5 6.0 ÎÎÎ Î ÎÎ Î ÎÎ ÎÎÎ 0.5 0.9 1.35 1.8 ÎÎÎÎ Î ÎÎ Î Î ÎÎ Î ÎÎÎÎ 0.5 0.9 1.35 1.8 ÎÎÎÎ Î ÎÎ Î Î ÎÎ Î ÎÎÎÎ 0.5 0.9 1.35 1.8 ÎÎÎ Î Î Î Î Î Î ÎÎÎ V ÎÎÎÎ Î ÎÎ Î ÎÎÎÎ VOH ÎÎÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎÎÎ Minimum High–Level Output Voltage ÎÎÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎÎÎ Vin = VIH |Iout| /C0118 20 µA ÎÎÎÎ Î ÎÎ Î ÎÎÎÎ 2.0 4.5 6.0 ÎÎÎ Î ÎÎ ÎÎÎ 1.9 4.4 5.9 ÎÎÎÎ Î ÎÎ Î ÎÎÎÎ 1.9 4.4 5.9 ÎÎÎÎ Î ÎÎ Î ÎÎÎÎ 1.9 4.4 5.9 ÎÎÎ Î Î Î ÎÎÎ V ÎÎÎÎ Î ÎÎ Î Î ÎÎ Î ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎ Î Î ÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎ Î Î ÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎÎÎ Vin = VIH |Iout| /C0118 2.4 mA |Iout| /C0118 6.0 mA |Iout| /C0118 7.8 mA ÎÎÎÎ Î ÎÎ Î Î ÎÎ Î ÎÎÎÎ 3.0 4.5 6.0 ÎÎÎ Î ÎÎ Î ÎÎ ÎÎÎ 2.48 3.98 5.48 ÎÎÎÎ Î ÎÎ Î Î ÎÎ Î ÎÎÎÎ 2.34 3.84 5.34 ÎÎÎÎ Î ÎÎ Î Î ÎÎ Î ÎÎÎÎ 2.2 3.7 5.2 ÎÎÎ Î Î Î Î Î Î ÎÎÎ This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high–impedance cir- cuit. For proper operation, Vin and Vout should be constrained to the range GND /C0118 (Vin or Vout) /C0118 VCC . Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC ). Unused outputs must be left open.

High–Speed CMOS Logic Data DL129 — Rev 6

3 MOTOROLA

DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND) ÎÎÎ ÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎ Guaranteed Limit ÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ Unit ÎÎÎÎ ÎÎÎÎ ÎÎÎÎ /C0118 125/C0095C ÎÎÎÎ ÎÎÎÎ ÎÎÎÎ /C0118 85/C0095C ÎÎÎ ÎÎÎ ÎÎÎ – 55 to 25/C0095C ÎÎÎÎ ÎÎÎÎ ÎÎÎÎ VCC V ÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎ Test Conditions ÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎ Parameter ÎÎÎÎ ÎÎÎÎ ÎÎÎÎ Symbol ÎÎÎÎ Î ÎÎ Î ÎÎÎÎ VOL ÎÎÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎÎÎ Maximum Low–Level Output Voltage ÎÎÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎÎÎ Vin = VIL |Iout| /C0118 20 µA ÎÎÎÎ Î ÎÎ Î ÎÎÎÎ 2.0 4.5 6.0 ÎÎÎ Î ÎÎ ÎÎÎ 0.1 0.1 0.1 ÎÎÎÎ Î ÎÎ Î ÎÎÎÎ 0.1 0.1 0.1 ÎÎÎÎ Î ÎÎ Î ÎÎÎÎ 0.1 0.1 0.1 ÎÎÎ Î Î Î ÎÎÎ V ÎÎÎÎ Î ÎÎ Î ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎÎÎ Vin = VIL |Iout| /C0118 2.4 mA |Iout| /C0118 6.0 mA |Iout| /C0118 7.8 mA ÎÎÎÎ Î ÎÎ Î ÎÎÎÎ 3.0 4.5 6.0 ÎÎÎ Î ÎÎ ÎÎÎ 0.26 0.26 0.26 ÎÎÎÎ Î ÎÎ Î ÎÎÎÎ 0.33 0.33 0.33 ÎÎÎÎ Î ÎÎ Î ÎÎÎÎ 0.4 0.4 0.4 ÎÎÎ Î Î Î ÎÎÎ ÎÎÎÎ ÎÎÎÎ Iin ÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎ Maximum Input Leakage Current ÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎ Vin = VCC or GND ÎÎÎÎ ÎÎÎÎ 6.0 ÎÎÎ ÎÎÎ ± 0.1 ÎÎÎÎ ÎÎÎÎ ± 1.0 ÎÎÎÎ ÎÎÎÎ ± 1.0 ÎÎÎ ÎÎÎ µA ÎÎÎÎ Î ÎÎ Î ÎÎÎÎ IOZ ÎÎÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎÎÎ Maximum Three–State Leakage Current ÎÎÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎÎÎ Output in High–Impedance State Vin = VIL or VIH Vout = VCC or GND ÎÎÎÎ Î ÎÎ Î ÎÎÎÎ 6.0 ÎÎÎ Î ÎÎ ÎÎÎ ± 0.5 ÎÎÎÎ Î ÎÎ Î ÎÎÎÎ ± 5.0 ÎÎÎÎ Î ÎÎ Î ÎÎÎÎ ± 10 ÎÎÎ Î Î Î ÎÎÎ µA ÎÎÎÎ Î ÎÎ Î ÎÎÎÎ ICC ÎÎÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎÎÎ Maximum Quiescent Supply Current (per Package) ÎÎÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎÎÎ Vin = VCC or GND Iout = 0 µA ÎÎÎÎ Î ÎÎ Î ÎÎÎÎ 6.0 ÎÎÎ Î ÎÎ ÎÎÎ 4.0 ÎÎÎÎ Î ÎÎ Î ÎÎÎÎ ÎÎÎÎ Î ÎÎ Î ÎÎÎÎ 160 ÎÎÎ Î Î Î ÎÎÎ µA NOTE: Information on typical parametric values can be found in Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D). AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6 ns) ÎÎÎÎ ÎÎÎÎ Sb l ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ P ÎÎÎÎ ÎÎÎÎ V ÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎ Guaranteed Limit ÎÎÎ ÎÎÎ Ui ÎÎÎÎ Î ÎÎ Î ÎÎÎÎ Symbol ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Parameter ÎÎÎÎ Î ÎÎ Î ÎÎÎÎ VCC V ÎÎÎ Î ÎÎ ÎÎÎ – 55 to 25/C0095C ÎÎÎÎ Î ÎÎ Î ÎÎÎÎ /C0118 85/C0095C ÎÎÎÎ Î ÎÎ Î ÎÎÎÎ /C0118 125/C0095C ÎÎÎ Î Î Î ÎÎÎ Unit ÎÎÎÎ Î ÎÎ Î Î ÎÎ Î ÎÎÎÎ tPLH , tPHL ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Î Î ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Maximum Propagation Delay, A to YA or B to YB (Figures 1 and 3) ÎÎÎÎ Î ÎÎ Î Î ÎÎ Î ÎÎÎÎ 2.0 3.0 4.5 6.0 ÎÎÎ Î ÎÎ Î ÎÎ ÎÎÎ ÎÎÎÎ Î ÎÎ Î Î ÎÎ Î ÎÎÎÎ 100 ÎÎÎÎ Î ÎÎ Î Î ÎÎ Î ÎÎÎÎ 120 ÎÎÎ Î Î Î Î Î Î ÎÎÎ ns ÎÎÎÎ Î ÎÎ Î Î ÎÎ Î ÎÎÎÎ tPLZ , tPHZ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Î Î ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Maximum Propagation Delay, Output Enable to YA or YB (Figures 2 and 4) ÎÎÎÎ Î ÎÎ Î Î ÎÎ Î ÎÎÎÎ 2.0 3.0 4.5 6.0 ÎÎÎ Î ÎÎ Î ÎÎ ÎÎÎ 110 ÎÎÎÎ Î ÎÎ Î Î ÎÎ Î ÎÎÎÎ 140 ÎÎÎÎ Î ÎÎ Î Î ÎÎ Î ÎÎÎÎ 165 ÎÎÎ Î Î Î Î Î Î ÎÎÎ ns ÎÎÎÎ Î ÎÎ Î Î ÎÎ Î ÎÎÎÎ tPZL , tPZH ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Î Î ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Maximum Propagation Delay, Output Enable to YA or YB (Figures 2 and 4) ÎÎÎÎ Î ÎÎ Î Î ÎÎ Î ÎÎÎÎ 2.0 3.0 4.5 6.0 ÎÎÎ Î ÎÎ Î ÎÎ ÎÎÎ 110 ÎÎÎÎ Î ÎÎ Î Î ÎÎ Î ÎÎÎÎ 140 ÎÎÎÎ Î ÎÎ Î Î ÎÎ Î ÎÎÎÎ 165 ÎÎÎ Î Î Î Î Î Î ÎÎÎ ns ÎÎÎÎ Î ÎÎ Î Î ÎÎ Î ÎÎÎÎ tTLH , tTHL ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Î Î ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Maximum Output Transition Time, Any Output (Figures 1 and 3) ÎÎÎÎ Î ÎÎ Î Î ÎÎ Î ÎÎÎÎ 2.0 3.0 4.5 6.0 ÎÎÎ Î ÎÎ Î ÎÎ ÎÎÎ ÎÎÎÎ Î ÎÎ Î Î ÎÎ Î ÎÎÎÎ ÎÎÎÎ Î ÎÎ Î Î ÎÎ Î ÎÎÎÎ ÎÎÎ Î Î Î Î Î Î ÎÎÎ ns ÎÎÎÎ Î ÎÎ Î ÎÎÎÎ C in ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Maximum Input Capacitance ÎÎÎÎ Î ÎÎ Î ÎÎÎÎ ÎÎÎ Î ÎÎ ÎÎÎ ÎÎÎÎ Î ÎÎ Î ÎÎÎÎ ÎÎÎÎ Î ÎÎ Î ÎÎÎÎ ÎÎÎ Î Î Î ÎÎÎ pF ÎÎÎÎ Î ÎÎ Î ÎÎÎÎ C out ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Î ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Maximum Three–State Output Capacitance (Output in High–Impedance State) ÎÎÎÎ Î ÎÎ Î ÎÎÎÎ ÎÎÎ Î ÎÎ ÎÎÎ ÎÎÎÎ Î ÎÎ Î ÎÎÎÎ ÎÎÎÎ Î ÎÎ Î ÎÎÎÎ ÎÎÎ Î Î Î ÎÎÎ pF NOTE: For propagation delays with loads other than 50 pF, and information on typical parametric values, see Chapter 2 of the Motorola High– Speed CMOS Data Book (DL129/D). C P Di i i C i (P T i Ch l)* Typical @ 25°C, VCC = 5.0 V FC PD Power Dissipation Capacitance (Per Transceiver Channel)* 32 pF * Used to determine the no–load dynamic power consumption: PD = CPD VCC 2f + ICC VCC . For load considerations, see Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D).

High–Speed CMOS Logic Data DL129 — Rev 6

5 MOTOROLA

MOTOROLA High–Speed CMOS Logic Data DL129 — Rev 6 OUTLINE DIMENSIONS J SUFFIX CERAMIC PACKAGE CASE 732–03 ISSUE E N SUFFIX PLASTIC PACKAGE CASE 738–03 ISSUE E DW SUFFIX PLASTIC SOIC PACKAGE CASE 751D–04 ISSUE E NOTES: 1. LEADS WITHIN 0.25 (0.010) DIAMETER, TRUE POSITION AT SEATING PLANE, AT MAXIMUM MATERIAL CONDITION. 2. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 3. DIMENSIONS A AND B INCLUDE MENISCUS. DIM MIN MAX MIN MAX INCHESMILLIMETERS A 23.88 25.15 0.940 0.990 B 6.60 7.49 0.260 0.295 C 3.81 5.08 0.150 0.200 D 0.38 0.56 0.015 0.022 F 1.40 1.65 0.055 0.065 G 2.54 BSC 0.100 BSC H 0.51 1.27 0.020 0.050 J 0.20 0.30 0.008 0.012 K 3.18 4.06 0.125 0.160 L 7.62 BSC 0.300 BSC M 0 15 0 15 N 0.25 1.02 0.010 0.040 /C0095/C0095/C0095/C0095 A 11 0 B F C SEATING PLANE DH G K N J M L NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. M L J 20 PL MBM0.25 (0.010) T DIM MIN MAX MIN MAX MILLIMETERSINCHES A 25.66 27.171.010 1.070 B 6.10 6.600.240 0.260 C 3.81 4.570.150 0.180 D 0.39 0.550.015 0.022 G 2.54 BSC0.100 BSC J 0.21 0.380.008 0.015 K 2.80 3.550.110 0.140 L 7.62 BSC0.300 BSC M 0 15 0 15 N 0.51 1.010.020 0.040 /C0095/C0095/C0095/C0095 E 1.27 1.770.050 0.070 –A– SEATING PLANE K N FG D 20 PL –T– MAM0.25 (0.010) T E B C F 1.27 BSC0.050 BSC NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.150 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.13 (0.005) TOTAL IN EXCESS OF D DIMENSION AT MAXIMUM MATERIAL CONDITION. –A– –B– SAM0.010 (0.25) B ST D20X MBM0.010 (0.25) P10X J F G18X K C –T– SEATING PLANE M R X 45/C0095 DIM MIN MAX MIN MAX INCHESMILLIMETERS A 12.65 12.95 0.499 0.510 B 7.40 7.60 0.292 0.299 C 2.35 2.65 0.093 0.104 D 0.35 0.49 0.014 0.019 F 0.50 0.90 0.020 0.035 G 1.27 BSC 0.050 BSC J 0.25 0.32 0.010 0.012 K 0.10 0.25 0.004 0.009 M 0 7 0 7 P 10.05 10.55 0.395 0.415 R 0.25 0.75 0.010 0.029 /C0095/C0095/C0095/C0095

High–Speed CMOS Logic Data DL129 — Rev 6

7 MOTOROLA

CASE 948E–02 ISSUE A DIM A MIN MAX MIN MAX INCHES 6.60 0.260 MILLIMETERS B 4.30 4.50 0.169 0.177 C 1.20 0.047 D 0.05 0.15 0.002 0.006 F 0.50 0.75 0.020 0.030 G 0.65 BSC 0.026 BSC H 0.27 0.37 0.011 0.015 J 0.09 0.20 0.004 0.008 J1 0.09 0.16 0.004 0.006 K 0.19 0.30 0.007 0.012 K1 0.19 0.25 0.007 0.010 L 6.40 BSC 0.252 BSC M 0 8 0 8 /C0095/C0095/C0095/C0095 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE –W–. ÍÍÍÍ ÍÍÍÍ ÍÍÍÍ 11 0 1120 PIN 1 IDENT A B –T– 0.100 (0.004) C D G H SECTION N–N K JJ 1 N N M F –W– SEATING PLANE –V– –U– SUM0.10 (0.004) V ST 20X REFK L L/22X SU0.15 (0.006)T DETAIL E 0.25 (0.010) DETAIL E 6.40 0.252 SU0.15 (0.006)T Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. Mfax is a trademark of Motorola, Inc. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution;JAPAN : Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center, P.O. Box 5405, Denver, Colorado 80217. 303–675–2140 or 1–800–441–2447 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 81–3–3521–8315 – US & Canada ONLY 1–800–774–1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 INTERNET : http://www.mot.com/SPS/ MC74HC240A/D◊